Used Gear Tester for sale (6,817)

Condition: used, max. wheel diameter 0-200 mm max. module 25 min. module 0,5 Fodpstuxa Uefx Aarjfw

Condition: used, Chroma Type: ATE 17020 The Chroma 17020 is a highly professional, modular test system for lithium-ion & other battery pack qualification. Particularly strong in: - Lifetime testing, BMS verification, and validation of complex charging cycles - High energy recovery – up to 85% efficiency - Flexible expansion through numerous channels or higher current ranges - Enterprise deployment with extensive safety features & data persistence Technical data – Chroma ATE 17020 PTS Feature Specification Model: Chroma ATE 17020 PTS System type: Regenerative battery pack test system (charge/discharge test) Channel output: 600 W to 60 kW (modular and scalable) Total output: Up to 600 kW (depending on configuration) Voltage range: 20 V / 60 V / 100 V / 200 V / 500 V Current per channel: Depending on module: from a few amps up to >300 A per channel Parallel operation: Yes, for higher current up to 2,600 A Current and voltage accuracy: ±(0.05% of reading + 0.05% of range) Power accuracy: ±0.1% Transition time (charge/discharge): < 50 ms Sampling rate (measured data): up to 50 kHz (with BatteryPro) Data logging: Cyclic, 10 μs – 1 s / memory for 60 min power failure Test modes: CC, CV, CP, CC-CV, DCIR, pulse, drive cycle, dynamic profiles Number of channels: Up to 60 channels (expandable) Communication: CAN, S-Bus, Ethernet, USB Software: Chroma BatteryPro (test programming, real-time monitoring) Protection functions: OVP, UVP, OCP, UCP, OTP, reverse polarity, wire loss, delta V/I, etc. Energy recovery: Yes – up to 85% energy efficiency, grid-friendly (THD < 5%) Cooling: Fan cooling, low waste heat due to energy recuperation Temperature monitoring: Optionally integrable, range 0–90°C ±2°C Dimensions & weight: Depending on configuration (e.g. 19″ rack, approx. 300 kg) Mains connection: 3-phase, 400 V AC (depending on model) Applications: E-mobility, battery development, quality assurance, cell research Weight: approx. 455 kg Condition: used Scope of delivery: (See picture) Ffedpfxewwrxae Aarsw (Specifications and technical data are subject to change and errors excepted!) If you have further questions, we are happy to assist you by phone.

Condition: excellent (used), functionality: fully functional, Year of construction: 2002, operating hours: 48,651 h, Mazak Space Gear-510 MKII 2.5 kW Year of manufacture December 2002 - after renovation!!! Very good condition! Ffodowqr Tdspfx Aarow Meter reading 48651 hours Operating system Fanuc L-64

Condition: excellent (used), functionality: fully functional, Year of construction: 2007, operating hours: 41,417 h, Mazak Hyper Gear 510 4.0 kW Year of production February 2007 Meter reading 41417 hours MAZATROL operating system very good condition Technical data of the MAZAK HYPER GEAR 510 laser cutter - laser power: 4 kW - feeds in the X/Y/Z axes: 3070/1545/100 mm - dimensions of the work table (length x width): 3000 x 1500 mm Ffsdpfswqr Twsx Aarew - maximum weight of the workpiece: 930 kg - maximum dimensions of the workpiece (length x width x height): 3050 x 1525 x 25 mm - laser type: CO2

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2002, operating hours: 25,769 h, machine/vehicle number: 159687, laser power: 2,500 W, travel distance X-axis: 3,335 mm, travel distance Y-axis: 1,545 mm, travel distance Z-axis: 420 mm, swivel angle A-axis (max.): 360 °, No reserve price - guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel X-axis: 3335 mm Travel Y-axis: 1545 mm Travel Z-axis: 420 mm A-axis: ±360 ° B-axis: ±135 ° Maximum workpiece dimensions: 3050 x 1525 x 22 mm Maximum table load: 810 kgf MACHINE DETAILS Laser power: 2500 W Laser model: YB-L250A8M NC control: Mazak & Fanuc L-64 Dimensions & Weight Machine dimensions: 7,525 x 2,875 x 2,300 mm Chiller dimensions: 920 x 1,600 x 1,780 mm Extraction unit dimensions: 850 x 850 x 930 mm Machine weight: 14.6 t Operating hours: 25,769 h EQUIPMENT Fodpoymfmbjfx Aarjfw Chiller Extraction unit

Condition: good (used), Year of construction: 2002, Clampable cutter head type (max.) 460 mm Cutter head weight (max.) 150 kg Mounting disc diameter for cutter heads (Ø) 360 mm Mounting cone for cutter heads Nominal diameter Ø 58,227 mm travel -z axis 200 mm diagram-drawing enlargement ±10 - ± 500 µm weight of the machine ca. 2,3 t dimensions of the machine ca. 2 x 1,5 x 2,03 m In the manufacturing process for spiral-toothed bevel gears, the quality of the gear cutting gear cutting tools used plays a decisive role. Particularly in high gear cutting quality and a long service life can only be achieved with precisely can only be achieved with precisely adjusted cutterheads. The Oerlikon cutterhead setting and testing device CS 200 enables quick and easy setting of the individual knives and simple adjustment of the individual knives, it checks the position and documents the measurement results. The measuring sequence on the CNC-controlled testing device is partially automated: The individual actions for carrying out the actions for carrying out the sequence are displayed on the screen via the operator guidance. The positioning of the individual knives in the cutter head and the height of the knife tips is largely automatic thanks to a special sequence and is simultaneously documented by means of a run-out diagram. A subsequent measuring sequence checks the radial position of the inner and outer cutting edges of all knives in the cutterhead. If individual test parameters on the knives do not correspond to the the tolerance specifications, this can be individually repositioned. The combination of semi-automated setting sequence, operator-guided set-up actions and automatic operator-guided set-up actions and automatic measuring sequence, Fedpfx Aew N S E Asarefw cutterheads can be can be set conveniently, quickly and with high precision. Operator-guided setting and test sequence - Graphic display of the cutter head design and the measurement results with tolerance check - Instructions for the operator in plain text Instructions for the operator in plain text (without coded information) - Simple assignment of the measurement results to the knives - Documentation of the setting and measurement results via printer- Setting and test sequence suitable for ARCON®, RSR, Spirapid, SPIRON®, TRI-AC® types - Interface for neutral data

Condition: good (used), Year of construction: 2007, max. wheel diameter 500 mm gear width 200-400 mm module 12 turning speeds 0-3250 U/min bracke pressure bis max. 95 Nm inner taper Konus #39 Control Fanuc 16 Fsdpfevr Hf Eex Aarjfw total power requirement 15 kW weight of the machine ca. 6 t dimensions of the machine ca. 2.350 x 2.240 x 2.500 mm HIGHLY FLEXIBLE TESTING OF HARD, FINISHED AND GREEN SPIRAL BEVEL AND HYPOID GEAR SETS The T 60 bevel gear testing machine is a CNC testing machine with three linear axes for the fully automatic hard and soft testing of spiral bevel and hypoid gear sets with a 90° axis angle. It offers versatile objective and subjective testing options with speeds up to 3,250 min and braking torques up to max. 95 Nm.

Condition: good (used), Year of construction: 2001, Equipped with: Power Stock Fanuc 5-Axis CNC Control 160M 400mm Honing Wheel X Axis Pulse Generator Coolant System w/Twin Filters Magnetic Chip Separator Honing Tool Set up for Last Job is Still in Machine Internal Diameter of Honing Tool on Machine is 14" Work Light Power Door Auto Dress 5-Part Program Instruction Book for 16M Control Instruction Book for Set-Up and Operation Specifications: Maximum Outer Diameter: 250 (350) Minimum Outer Diameter: 30 Maximum Overall Length: 400mm Maximum Tooth Width: 45mm Module: 1.0-3.0 Cross Feed Device(Z Axis): 430mm Max. Travel Honing Wheel Cutting Feed Device(X Axis): 370 Max. Travel Honing Wheel Swing Device(C Axis): Swing Angle: +30 Degress Honing Wheel Rotation Drive Device(A Axis): Honing Wheel Spindle Speed R/Min: 500 Honing Wheel Outer Dia.: 300 (400) Maximum Honing Wheel Width: 50mm Crowning Device (Y Axis): Maximum Rocking Angle: 1.6 Degrees Motor Types: Z-Axis Drive Motor: 1.8Kw X-Axis Drive Motor: 1.8Kw Y-Axis Drive Motor: 0.7Kw C-Axis Drive Motor: 1.8Kw A-Axis Drive Motor: 2.2/3.7Kw Maximum Distance Between Centers: 600mm Fjdpfxorualps Aarofw Center Height: 1,100mm Floor Space: 2,170W X 2,800D X 2,100H Mass Of Machine: 4,500Kg

Condition: used, Year of construction: 1996, functionality: fully functional, machine/vehicle number: 25734, Equipped with: Fanuc 150MB Control Hydraulic Chucking Work Spindle Large Bore Work Spindle #80 Taper Stock Divider Helical Motion Modified Roll Hansen Coolant Chiller & Filtration Coolant Tank & Pumps Chip Conveyor Chip Hopper Reven Mist Collector Hydraulic System Transformer Cutter Bolt Work Light Operator Platform Hand Tools Documentation Specifications: Extreme Ratio: Face Milling: 10:1, Face Hobbing: 10:1 Full Depth: Maximum: Face Milling:1.25" (31.75mm), Face Hobbing: 0.93" (23.50mm) Fsdpfx Aoxaqa Searjfw Face Width: Maximum: Face Milling:6.00" (152.00mm),Face Hobbing: 3.00" (76.20mm) Range of Tooth Numbers: 1-300 Inclusive Gear Pitch Diameter, Maximum: 1000 mm (39.37") Cutter Size, Maximum: 18" (diameter) Face Milling Cutter Size, Maximum: 350 mm (radius) Face Hobbing Root Angle Range (B-Axis) 5 deg.to 90 deg., Face Hobbing:5 deg. to 90 deg. Machine Center to Work Spindle Face:9.00"Fixed, 229mm (Fixed) A-Work Spindle: 0 to 67 RPM, 0 to 333 RPM B-Swinging Base: 0 to 30 deg./sec, N/A C-Cutter: 0 to 500 deg., Same X-Horizontal: +/-305mm (+/-12") Y-Vertical: +/-305 mm (+/-12") Z-Sliding Base: -25/+700mm (-1/+28") B-Root Angle: -5 Degree/+90 Degree Diameter of Taper Hole at Large End: 8" (#80 Taper) to 6" (#60 Taper) Taper Per Foot:3/4", Same Depth of Taper Front:6", 152.40 mm Depth of Bore: 678 mm (26.7") Diameter of Taper Bore: 140 mm (5.5") Diameter Through Spindle of Hole:7.125", 180.98 mm MACHINE DIMENSIONS: Length x Width:233"x 209", 5920 mm x 5310 mm Height: 129", 3280 mm Weight: 65,000 lbs., 29,484 kg

Condition: used, Year of construction: 2011, machine/vehicle number: 25621, workpiece diameter (max.): 360 mm, Equipped with: Gear Spindle Runout: -Radial (Bore): .00005 -Axial (Face): .00005 Pinion Spindle Runout: -Radial (Bore): .00005 Axial (Face): .00005 Axis Repeatability: -X: .0001 -Y: .0001 -Z: .0001 Axis Lost Motion: -X: .00005 -Y: .00005 -Z: .00005 Fanuc 160I MB Control Fodpexdfanjfx Aarefw Base Work Holding Draw Bars Automatic Doors Spindle Chiller Transformer Hydraulic System Festo Pneumatics Automation Interface Available SPECIFICATIONS: Maximum Gear Outside Diameter: 360 mm (14.2") Maximum Pinion Outside Diameter: 340 mm (13.4") Maximum Pinion Drive Speed: 3000 rpm Maximum Gear Drive Speed: 1500 rpm Offset Vertical 150 mm ( 5.9") Pinion Cone Range: (90) (135-350) (70) (146-438)* (110) (51-343)* Gear Cone Range: (90) (65-280) (70) (78-306)* (110) (56-284)* Standard Testing Torque Load 2 to 90 Nm (1.5 to 66 ft-lb). Parallel Axis - face-to-face 147 - 362 - Center Distance -7 - 250 Pinion Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 419 mm (16.5") Gear Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 250 mm (9.8") Floor Space (width & length) 2100 x 2550 mm (82.7 x 100.4") Height (to top of stack light) 2750 mm (108.3") Weight (base machine) 9100 Kg (20062 lbs)

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Ffsdpfsrtrzdox Aarsw Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Depth of Taper: 8" Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Condition: used, Year of construction: 1977, machine/vehicle number: 19909, Equipped with: Index Plate Geneva Cam Cutter Body Hydraulic Work Clamping Coolant Pump & Tank Chip Conveyor Additional Cutter Bodies, Index Plates & Geneva Cams Available Specifications: Minimum Outside Cone Distance: 2.75" Maximum Cone Distance: 10" Fjdpfsxdfazex Aarjfw Maximum Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 Deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Depth of Taper: .625" Cutter Speeds: 15.6 to 87.7 RPM Feeds (seconds/tooth): 5 to 34.3 Main Motor: 10hp, 1800 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approximate Floor Space: 118" x 86.5" Needed Overall Height: 70" Approximate Net Weight: 18,820 lbs Shipping Weight Boxed for Export: 20,500 lbs

Condition: used, Year of construction: 1973, machine/vehicle number: 24109, Equipped with: Ffedpoxdfa Ujfx Aarow Stock Divider Hydraulic Work Clamping Chip Conveyor Cutter Clamping Bolt Index Plate Change Gears Hydraulic System Coolant System Specifications: Min. Outside Cone Distance: 2.75" Max. Cone Distance: 10" Max. Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Depth of Taper: .625" Cutter Speeds: 6.8 to 16.5 RPM Feeds (seconds/tooth): 3 to 9 Main Motor: 5hp, 900 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approx. Floor Space: 118" x 86.5" Needed Overall Height: 70" Approx. Net Weight: 16,000 lbs Shipping Weight Boxed for Export: 17,000 lbs

Condition: good (used), Year of construction: 2019, machine/vehicle number: 25653, Equipped with: -Automatic Central Lubrication System -Machine Guard -Indramat - MTX and Sercos CNC Control -The standard machine is equipped with CNC-control make Indramat - MTX and SERCOS-interface -Tool Dressing (Automatic dressing cycle of the dressing master and honing wheel tip diameter by a diamond coated dressing roll. The dressing cycle of workpieces can be pre-selected) -Electronic Indexing Unit -Operator and Maintenance Manual -All Electrical Drawings -PLC Language in English -Software and Hardware for Remote Diagnosis -High Precision Control of the Stock Allowance Material -Manual Loading on Spindle for Prototypes -Software for Infeed Optimized Cycle Type Reduction (Adaptive Honing) -Software for Vario Speed Dressing -Software for Calibration of Master Gears -Software for Timing Gears (including additional sensor for the hole of 4mm) -Software for Shortening of Workpiece Change-Over Time -Clamping Cylinder -RITTAL Cooling Unit -Lighting for Working Area -Installation of Vibration Detecting Sensors -Coolant Unit -Electrostatic Oil Mist Exhauster IFS With Rigid Piping -Internal Automation -Pallet Ring Conveyor System FlexLink (L-form shape see approved layout) -Parallel - Double Gripper -Pick and Placer Between Pallet Conveyor and Internal Loader -Extended Loading Length of the Pick and Placer Specifications: Workpiece: -Part Diameter: 20-150 mm -Maximum Face Width: 70 mm -Part Weight: 20 kg Ffodpfow Iquysx Aarsw -Number of Teeth: 6-150 -Module: 1-5 mm Workpiece Spindle: -Maximum Speed: 6000 1/min -Installed Power: Approx. 25 kW Tool: -OD of Honing Wheel: 270 mm -Widths of Honing Wheel: 20-70 mm -Honing Wheel Material: Ceramics Tool Spindle: -Maximum Speed: 2000 1/min -Installed Power: Approx. 25 kW Machine: -Total Connected Load, Approx: 70 kVA -Floor Space (w x l x H): -Total Weight, Approx: 11 Ton -Bosch Rexroth MTX Control CML 85 Longitudinal Slide, Z-Axis: -Linear Drive -Drive Torque: 3,700 Nm -Infeed Speed: 60 m/min -Theoretical Infeed: 200 m/min -Drive Length, Maximum: 400 mm Cross Slide, X-Axis: -Linear Drive -Drive Momentum: 2,150 Nm -Infeed Speed: 60 m/min -Theoretical Infeed: 200 m/min -Drive Length, Maximum: 1050 mm Swiveling Axis, W-Axis: -AC-Servo Drive: 10,000 1/min -Setable Gear Transmission: i=5000:1 -Swiveling Angle: -90 Degrees / +16 Degrees Workpiece Spindle, C-Axis: -Direct Drive, Maximum RPM: 7,000 1/min -Drive Power: 30 kW -Drive Torque: 112 Nm -Digital Measuring System Tool Spindle, B-Axis: -Direct Drive (hollow spindle drive), Maximum RPM: 2000 1/min -Drive Power: 30 kW -Drive Torque: 150 Nm -Digital Measuring System

Condition: good (used), gear diameter: 508 mm, total height: 1,780 mm, total length: 2,990 mm, total width: 2,200 mm, MODEL 610 GLEASON GEAR ROUGHER/FINISHER Equipped with: Fodpfxortryko Aarsfw Hydraulic Workholding Pendant Control Chip Conveyor Index Plate Geneva Cam Change Gears Hydraulic System Coolant System Manuals Specifications: Maximum Gear Pitch Diameter: 20" Cutter Diameters: 9", 10.5", 12",14",16", 18" Whole Depth: 1.250" Root Angle: 60 to 80 deg. Face Width: 3.0" Extreme Ratio (Minimum): 2.25 to 1 Number of Teeth: 20 to 75 Diameter of Taper Hole at Large End: 3-27/64" Cutter Speeds (Per Minute) for Roughing: 15.6' to 87.7' Feeds (Seconds Per Tooth) for Roughing: 3 to 35 Cutter speeds (Per Minute) for Finishing: 6.8' to 20.5' Feeds (Seconds Per Tooth) for Finishing: 3 to 9 Floor Space: 118" x 86.5" x 70" H Weight: 17,500 lbs.

Condition: good (used), geared motor, electric motor -Speed: 68 rpm -Power: 0.18 kW Fodpfx Aaedaa Hlorjfw -Design: B3 -Shaft diameter: Ø 24 mm Protection rating: Quantity: 1 piece available -Dimensions: 350/175/H190 mm -Weight: 14 kg

Condition: not inspected (used), functionality: unexamined, table diameter: 50 mm, No minimum price – guaranteed sale to the highest bidder! Ffedeyr Rqcopfx Aarsw Bidding obligates timely collection between 04.05.26 and 07.05.26. TECHNICAL DETAILS Diameter of support surface: 50 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 500 x 200 x 650 mm Machine weight: 100 kg External reference: Lot 85

Condition: good (used), Year of construction: 1979, functionality: fully functional, machine/vehicle number: 1137.05, Used tool grinding machine Manufacturer: KAPP Model: AST305B Fodpfx Aswzk R Nsarjfw Year of manufacture: 1979 Serial number: 1137.05 With accessories

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 27506, Complete overhaul in 2009 Ffedpjxtpg Rsfx Aarew CNC gear hobbing machine Pfauter PE 150 Serial number: 27 506 Year of manufacture: 1991 – complete overhaul in 2009 CNC control: SINUMERIK 840 D

Condition: like new (used), Year of construction: 2017, max. wheel diameter 100 mm gear width 26 mm max. module 31 min. module 0,1 Control Siemens 840 D SL Number of working hours 9598 h total power requirement 45 kW weight of the machine ca. 7 t dimensions of the machine ca. 4x3x2,5 m Gleason 100S gear shaping machine for the production of internally and externally toothed cylindrical gears and Fodpfov Ehbbex Aarofw other cylindrical workpiece circumference regularly occurring profiles and moulds as well as for the production of profiles using the single part process. Technical data: Nominal workpiece diameter 100 mm Largest circumferential diameter 150 mm Machine nominal module approx. 3 mm (Guide value depending on the respective machining task.) Shaping spindle stroke speed range 0 - 3,000 1/min Stroke position adjustment range (manual) 20 mm Largest toothing width 26 mm Smallest pitch height of the hydrostatic inclined guide 400 mm Smallest/largest distance between tool axis - 20/+ 180 mm and workpiece axis Stand inclination range (manual) - 1/+ 11° Tool holder (manual clamping) HSK-D63 (hollow shank taper according to DIN 69063) Weight of the machine approx. 7,000 kg with robot cell

Condition: excellent (used), Gear motor, electric motor, electric gear motor, worm gear motor, parallel shaft gear motor -Condition: Gear motor is unused -Manufacturer: SEW-Eurodrive, gear motor with brake, parallel shaft gear unit series F -Type: FH87/G DRS132S4BE5HF/TF -Speed: 68 rpm -Power: 5.5 kW Ffsdpfx Ajvvbnpoarow -Protection class: IP54 -Hollow shaft: Ø 60 x 280 mm -Brake: 28 Nm -Number: 2x motor available -Price: per piece -Dimensions: 760/335/H530 mm -Weight: 155 kg/piece

Condition: like new (used), Screw Jack GROB RTP 502-000-8 Screw Jack RTP 502-000-8 GROB Ffodpfx Aasyrydlsrsw 40:23 240/01 00000 Manufacturer: GROB Antriebstechnik Type: RTP 502-000-8 Design: screw jack / lifting gear Item number: 213554 Drawing number: 90010016737 Packaging: original wooden crate Condition: unused, original packaging from warehouse clearance

Condition: ready for operation (used), self aligning set of welding rotators one driven unit Ffodpox Enhyjfx Aarsw one non-driven unit max load capacity: 300 ton max rolling capacity: 450 ton speed range: 60 1200 mm/min min diameter of workpiece: 1000 mm max diameter of workpiece: 7800 mm spare wheels included Max weight on both supports: 450 ton Number of wheels: 24 wheels Dia x width wheels: dia 580 x 140 mm Coating material on wheels: steel

Condition: ready for operation (used), empty load weight: 160,000 kg, total length: 12,000 mm, total width: 7,000 mm, total height: 10,000 mm, laadvermogen: 300 ton Fedexpkh Iepfx Aarofw tafeldiameter: 9500 mm variabel draaien en variabel kantelen 180°

Condition: ready for operation (used), Year of construction: 2005, travel distance X-axis: 3,070 mm, travel distance Y-axis: 1,545 mm, travel distance Z-axis: 25 mm, overall weight: 14,800 kg, table load: 930 kg, number of axes: 3, This 3-axis Mazak Hyper Gear 510 was manufactured in 2005. It features an X-Y-Z axis stroke of 3070 × 1545 × 100 mm and a maximum workpiece size of 3050 × 1525 × 25 mm. With a rated laser output of 4000 W, this CO₂ laser cutting machine is designed for precision cutting. If you are looking to get high-quality cutting capabilities, consider the Mazak Hyper Gear 510 machine we have for sale. Contact us for further details. • Max. workpiece size: 3050 × 1525 × 25 mm • Rated laser output: 4000 W • CO₂ laser model: YB-L400A 8M (5E) Fjdpfx Aaeymn Dvsrofw • NC unit: Mazatrol Preview