Used Graphite for sale (168)

Condition: used, Year of construction: 2010, machine/vehicle number: 1000017741, inner dimension length: 1,000 mm, inner dimension width: 840 mm, inner dimension height: 815 mm, operating temperature: 1,700 °C, usable tank capacity: 685 l, No minimum price – guaranteed sale to the highest bidder! The machine was professionally dismantled and stored. All parts and connections are labeled for reassembly. An on-site inspection is possible at any time. TECHNICAL DETAILS Furnace chamber and usable space Usable batch space (W × H × L): 840 × 815 × 1,000 mm Total length of the graphite box: approx. 1,100 mm Usable volume: approx. 685 l Operating temperature: max. 1,700 °C Operating temperature under partial pressure: max. 1,500 °C Operating temperature under vacuum: max. 1,700 °C Temperature uniformity: ± 10 K Temperature fluctuation in the steady state: ± 5 K MACHINE DETAILS Process pressure range: 1 × 10⁻² < p < 1,040 mbar Final pressure in the empty, clean, and cold furnace: < 1 × 10⁻² mbar Leak rate: < 5 × 10⁻³ mbar·l/s Power supply: 3 × 400 V, 50 Hz Permissible voltage fluctuation: max. ± 5 % Installed heating power: max. approx. 190 kW Electrical power of the pump station: approx. 14 kW Cooling water flow rate: approx. 150 l/min Cooling water temperature: 20–30 °C Cooling water pressure: 2–4 bar Cooling water quality requirements: according to specification PW 800 943 ND Compressed air for valve operation: 4–5 bar Nitrogen inlet pressure: 5–7 bar Hydrogen inlet pressure: 5–7 bar EQUIPMENT Double-walled furnace chamber made of stainless steel with water cooling Internal graphite box for precise guidance of the process gases Post-cleaned graphite components Automatic control of the entire process Pump station Hnodpfxez I Tt Is Ak Uou Labeled lines and connections for easier recommissioning Note: Two internal graphite heating elements were damaged during dismantling and must be replaced.

Condition: used, Year of construction: 2001, operating hours: 18,250 h, functionality: fully functional, machine/vehicle number: 6097/01, type of input current: three-phase, total height: 2,000 mm, total width: 3,000 mm, total length: 5,000 mm, control cabinet height: 2,000 mm, control cabinet length: 800 mm, control cabinet width: 600 mm, input voltage: 380 V, temperature: 950 °C, control voltage: 220 V, input current: 30 A, input frequency: 50 Hz, overall weight: 2,500 kg, Equipment: documentation/manual, Morgan gas electric tilting aluminium oven type GE60, platform and Foseco rotor degasser. Year 2001 and 18400 operating hours. Melting capacity: 500kg aluminium Comes with 1 extra graphite crucible and stand. Hnjdpfxozhad As Ak Uou

Condition: excellent (used), Year of construction: 1999, Double-sided, multi-purpose edge sanding machine with oscillation and 200mm sanding height. Langzauner LZK 4-S with a veneer edge sanding side and a solid wood sanding side. 200mm sanding width Motorized sanding belt oscillation, therefore no compressed air connection is necessary Drive motor 400V / 3kW Front work table for sanding veneer edges with a stop guide rail (for veneer overhang) Veneer sanding device with fine adjustment, foldable Spring-mounted table, height-adjustable and can be positioned to the side Angle stop Rear, adjustable work table for sanding solid wood Both tables are height-adjustable to utilize the entire sanding belt Belt dimensions 3000 x 200mm Side extension table for radius sanding on the 150mm belt roller Feed support holder 68mm Central dust extraction connection 140mm Very stable chassis, 2 swivel castors, 2 steering castors and a lever brake for locking CE marking All graphite pads and dust extraction hoses have been replaced Hjdpez I T Apefx Ak Ujnu Original paint, only touched up in some areas Excellent condition from a small restoration workshop Some sanding belts are included Dimensions approx. 1800 x 1000 x 1250mm (L x W x H). Weight approx. 650kg. The machine can be demonstrated on site by appointment. We only offer machines that are ready for demonstration and are in our warehouse; see "other offers from this provider".

Condition: refurbished (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: 025, travel distance X-axis: 800 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 500 mm, controller manufacturer: Heidenhain, controller model: iTNC530, total height: 2,800 mm, total length: 3,000 mm, total width: 2,500 mm, table width: 600 mm, table length: 800 mm, table load: 800 kg, overall weight: 9,500 kg, spindle speed (max.): 36,000 rpm, operating hours of spindle: 9 h, spindle nose: HSK 50E, number of spindles: 1, number of slots in tool magazine: 30, input voltage: 400 V, type of input current: AC, Equipment: chip conveyor, documentation/manual, For sale is a used high-speed machining center from the manufacturer MIKRON. High-precision CNC machining center from Mikron / GF AgieCharmilles, designed for demanding HSC machining in toolmaking, graphite and electrode machining, as well as for flexible series production. Additionally equipped with APS (Advanced Process System) and ITC (Intelligent Thermal Control) for maximum process reliability and thermal stability. At “Der Spindel Doctor”, a Step-Tec spindle (a key component of the machining center) was professionally overhauled (report and invoice included) and put back into operation after balancing and inspection. The machine will be completely set up and tested according to the Mikron protocol. During the machine inspection, many wear parts were replaced: X-axis encoder and scale, pneumatic cylinders on the tool changer, tool holders, pneumatic maintenance unit, pneumatic hoses, MMS hoses, water hoses, etc. The machine is energized and can be inspected and tested. By arrangement, the machine can be put into operation at your location. Hnsdpfxoz Dx She Ak Uou Accessories: 4-position pallet changer II Table chuck Preparation for PS 32.00 measuring probe Mobile handwheel Blum laser tool measurement system Spindle cooling unit Minimum quantity lubrication - Unilub Oil mist extraction Optical operating mode indicator Air nozzle on the spindle slide Chip conveyor (including coolant tank) General overhaul of the spindle

Condition: ready for operation (used), functionality: fully functional, Gas inlet: AR Alternatre Gas inlet. Good working condition. Hnedpsxnpw Esfx Ak Uju Please check out our other listings as well.

Condition: used, Year of construction: 2015, functionality: fully functional, NAKAMURA NTJ-100, CNC turning and milling center with FANUC 31i-B control • C-axis on the left spindle • C-axis on the right spindle • Milling drive on the upper turret • Milling drive on the lower turret • B-axis on the upper turret +/-91° • Y-axis +/- 40 mm on the upper turret • Y-axis +/- 32.5 mm on the lower turret • Bar capacity left 42mm A2-5, 6000 rpm • Bar capacity right 42 mm A2-5, 6000 rpm • 12/24 + 6 stations under 45° turret, top • 12/24 stations turret, bottom • 90° inclined bed • Interface for bar loader magazine, Hommel • Air blow-out, right spindle • Drive power left, FANUC AC11/7.5kW • Drive power right, FANUC AC 11/7.5KW • Chuck pressure monitoring, right and left • 19" touch monitor • Door lock • Clamping force control • Helical interpolation • NT-Nurse 2 • NT-Work navigator • Feed rate and rapid traverse adjustment switch • Transformer • CE marking • Memory capacity 2560 meters • Tool offset memory 99 items • Program management 2000 programs • Extended editor function • Background editor • Macro B • Direct input of drawing dimensions • G52-G59 • Polar coordinate interpolation • Cylindrical interpolation • Current documentation • Machine color RAL 9002, light gray • Door color RAL 7011, iron gray • Chip conveyor RAL 7024, graphite gray Machine options NTJ-100 Air and coolant blow-out through the right spindle Ø 65mm NTJ-100 Chuck blow-out, left spindle NTJ-100 Intelligent handwheel NTJ-100 Polygon turning function Manual tool probe, removable for left and right Workpiece unloading NTJ-100 Unloading with gripper hand on the upper turret for parts up to Ø 65 mm x length 150 mm / 3.0 kg NTJ-100 Material collection tray type A with enclosed collection box, left, for material remnants and finished part ejection, part size up to spindle bore 65 mm NTJ-100 enlarged main spindle, left, Ø 65 mm, spindle nose A6 NTJ-100 enlarged counter spindle, right, Ø 65 mm, spindle nose A6 Hnedpfjz Iy Urex Ak Usu Chip disposal Hinged belt chip conveyor for NTJ-100, discharge right. Manufacturer: AME. Color: RAL 7024. Motor right, in the direction of travel.

Condition: used, Year of construction: 2012, Condition: Used, ready for operation • The first unit is equipped with a Ø190 mm calibration roller with a grooved rubber coating, hardness 90 Shore. • The second, combined unit contains a Ø190 mm sanding roller with a grooved rubber coating, hardness 40 Shore. In addition, it includes a hard felt sanding pad mounted on an aluminium rail, with a graphite-grain surface for fine sanding. The pad is equipped with timer-controlled automatic operation. Options: Electronically controlled sanding pad divided into 42 sections. The unit is driven by an independent motor with inverter-controlled speed adjustment and the possibility of changing the direction of rotation. • The third unit is a finishing brush roller. Technical specifications: Working width: 1350 mm Sanding belt size: 1380 x 2200 mm Workpiece thickness: 3–160 mm Motor power of first unit: 11 kW Motor power of second (combined) unit: 11 kW Feed speed: 3–16 m/min Feed motor power: 1.5 kW Pneumatic connection: 6 bar Air consumption: 17 Nl/min Extraction port diameter: 158 mm Extraction air speed: 25 m/min Required extraction capacity: 3095 m³/h Net machine weight: 2450 kg Width: 2320 mm Length: 2030 mm Height: 2050 mm The table movement is carried out by four large-diameter trapezoidal threaded lead screws, which are mounted externally on the machine frame. Table rollers: one roller is positioned before and one after the feed belt. • The feed belt has a 60 Shore hardness rubber surface with a concave pattern. • Precise tracking of the feed belt is ensured by an automatic centering unit. Hodpezlxp Sofx Ak Uenu PRESSURE HOLD-DOWN UNITS • Rubber-coated pressure rollers are positioned before and after the processing units to ensure accurate holding-down of the parts being sanded. SAFETY EQUIPMENT • with CE standards. Options: • Electronically controlled sensing unit for the 42-section sanding pad • Front table extension with two roller cylinders • Rear table extension with two roller cylinders • Complete vacuum table with vacuum pump: 2.2 kW – 3 HP • Electro-pneumatic engagement/disengagement of the contact roller • Nozzle system for cleaning and cooling the sanding belt. A.S.S. (Air Saving System) • Kombi R (drum) Ø190 – electronically controlled sanding pad divided into 42 sections (32 mm pitch) • Electro-pneumatic engagement/disengagement of the contact roller • Electro-pneumatic engagement/disengagement of the sanding pad • Nozzle system for cleaning and cooling the sanding belt. A.S.S. (Air Saving System) • Possibility of reversing the sanding belt rotation direction • Electronic inverter 11 kW (15 HP) • IPC COMPACT 8.5" control panel • Scotch Brite roller Ø200 mm – 1.1 kW – 1.5 HP Specifications are provided for information only. This machine is offered for sale on behalf of a customer. Viewing is available by prior arrangement. Please contact us through the platform's messaging system for further information and the relevant technical contact details.

Condition: like new (used), Year of construction: 2021, operating hours: 30 h, functionality: fully functional, machine/vehicle number: AE00002612, grinding width: 1,350 mm, overall weight: 6,250 kg, grinding height: 170 mm, working height: 170 mm, table height: 900 mm, workpiece height (max.): 170 mm, The machine has only been in use for a few hours and is practically brand new. It is in perfect working order. See below for the full specifications: Hsdezcmcvepfx Ak Uonu DMC system T5C 1350 PF170-4M Lifting unit for a fixed work table, 900 mm from the ground * Working thickness: 3 to 170 mm BL 16 Infeed panel with reading bar for 'epics' sectioned pads, pitch 16 mm, or with PWM3 POSITION 01 TIE-5000 Working unit for an extractable internal cross pad PE 16T 'EPICS' sectioned electronic sanding pad, pitch 16 mm Working pressure control of the sectioned pad via the Pro-Sand control system Motor driven by an inverter, power up to 15 kW POSITION 02 DO 19 Oscillating unit fitted with 19 rotating 125 mm disc brushes 1.1 kW main motor driven by an inverter Independent motor for controlling the oscillating movement Electronic auto-set for the unit Sliding movement with motor driven by an inverter POSITION 03 BF 300 Working unit for a brush roller, diameter 300 mm 4 kW main motor driven by an inverter Double rotating direction of the brushing roller Electronic auto-set for the brush roller Side oscillation of the brush roller POSITION 04 BF 300 Working unit for a brush roller, diameter 300 mm 4 kW main motor driven by an inverter Double rotating direction of the brushing roller Electronic auto-set for the brush roller Side oscillation of the brush roller POSITION 05 SC-2620 Operating unit for a superfinishing pad Sanding belt rotation against the conveyor feed direction Electronic sanding belt swing control Disc brake ◦ Chevron belt dimensions: 1370 x 2186 mm ◦ Sanding belt dimensions: 1370 x 2620 mm PE 16/C 'EPICS' sectioned electronic sanding pad, pitch 16 mm 16 mm center-to-center distance of sectors Double-action pneumatic cylinders with adjustable push/counter-push Graphite cloth with quick extraction device Total management of its functionality by the "Pro-Sand" electronic control Working pressure management of sectioned pad via the Pro-Sand control system Timed oscillating clearing blowers 15 kW motor driven by an inverter OUTSIDE THE MACHINE SB/U 200 Outfeed working unit for abrasive cloth-coated rollers, diameter 200 mm Roller rotation against the conveyor feed direction / Manual adjustment of the roller working position / Abrasive cloth-coated roller, diameter 200 mm, 'Ultra Fine' type with silicon carbide fibers / 2.2 kW motor / Side oscillation of the brush roller OTHER DEVICES Perforated worktop and conveyor belt with a vacuum motor powered by an inverter up to 7.5 kW, integrated into the machine frame Front supporting worktop equipped with five idler rollers Rear supporting worktop equipped with five idler rollers 4 kW feed belt motor driven by an inverter Console with integrated PC "eye-M" and "Maestro Pro-Sand" electronic control with Tele Service system 1999 working programs / Virtual keyboard for fast settings of the machine / Production report / Interactive trouble-shooting program and self-diagnosis of the electronic cards / Display of electric and pneumatic diagrams / Display of the user manual, spare parts catalog, electric and pneumatic diagrams Vision panel door positioned on the service side Internal LED lighting for the machine

Condition: used, Used SGL Carbon Technic Sas (France) model CKL7 diam.16 - 10 blocks, graphite (DIABON NS1) heat exchanger/cooler-condenser with surface area 102,6 sq. meters. Has 10 graphite blocks, each diameter 765 mm x 347 mm height. Construction material of shell P265GH (W.Nr. 1.0425). Process side rated full vacuum/3bar at 1 to 110 deg.C. Design pressure -1/3Bar at 1 to 110 deg.c. Service side rated 5 bar design pressure at 1 to 40 deg.C. Process side capacity 542 litre and service side capacity 648 litre. Product inlet diameter: 450 mm and 100 mm outlet. Dimensions: 1000 mm diameter x 4520 mm height. Mounted on (3) lugs. New 2010. Hnedpfx Akjyi Ewfo Ueu Transport dimensions: 4700 mm lenght x 1 450mm width - 1700 hight. Transport weight: 5 600 kg, (only exchanger 4950 kg). Weight: Actual: Kg5600.0

Condition: used, Year of construction: 2021, functionality: fully functional, Dürr Ecopure VAR 2206 Thermal Oxidizer with Flue Gas Cleaning (2021) For burning liquid and gaseous waste streams including fluorinated gases, e.g. PFAS, and recovery of aqueous hydrogen fluoride Emissions limits SO2 ≤ 100 mg/Nm³ NOX ≤ 30 mg/Nm³ CO ≤ 50 mg/Nm³ CF4 ≤ 70 mg/Nm³ HF ≤ 1 mg/Nm³ NH3 ≤ 2 mg/Nm³ Comprising Direct fired thermal oxidizer Hot gas cooling and acid recovery Alkaline wet scrubber Honeycomb selective catalytic reduction deNOx system >1M cost spare parts Direct fired thermal oxidizer Including 2x natural gas combustion chambers and burners - High calorific liquid waste requires safe ignition supplemental hydrogen supply for acid formation - Gaseous waste streams injected via nozzles downstream and close to the burner - 1.5MW multi-fuel natural gas & liquid waste (minor fuel stream) burner with natural gas capacity up to 200Nm3/h - 1400C normal, 1540C max allowable temperature destruction of pollutants to reduce emissions with 3.28 MW thermal energy transfer - 2 seconds minimum residence time in combustion chamber at 1400C - 1,800mm combustion chamber internal dia. - Approx 300mm refractory lining - 2,400mm combustion chamber external dia. - 12,000mm combustion chamber internal length - 3.28MW maximum thermal capacity - 4,900Nm3/h, 60mbar, 14kW combustion air fans One chamber is active, the other one is on standby and can be prepared, repaired, or maintained. This allows minimizing shutdown and changeover time to only several days Wet scrubber hot gas cooling and acid recovery SGL Carbon Diabon HT-PQ 850 graphite pipe quencher - 6,000 Nm3/h capacity flow - 1,100 mm dia. - 2,000mm high - pumps SGL Carbon Diabon THX-RS falling film absorber shell & tube heat exchanger - 1,100mm dia. - 4,500mm tube length - 595 no. tubes - 22mm tube internal dia. - Graphite, carbon steel - pumps Quench vessel - PP/FRP - 1,100mm dia. - Approx. 6,000mm high 2x Scrubber absorber columns, each - Shell FRP/PP - Internals PP - 1,000mm dia. - 11,000mm high - Pumps - Dosing station FRP 5m3 Emergency water tank - 1,600mm dia. - 3,000mm high - 3kW heating 2x Teblick 100,000L HDPE hydrofluoric acid tanks (2019) Honeycomb selective catalytic reduction deNOx system - 5,900Nm3/h, 130mbar, 42kW induced draft fan - 320 kW gas/gas heat exchanger Hnodpfx Aez Ai Tpok Uou - 500 kW capacity reheat burner - 1.2m deNOx honeycomb catalyst Clean gas outflow Stack with flow & temperature measurement Spare parts include - 200 items of sensors, pumps, valves, gaskets, joints etc. - Graphite quencher - Falling film absorber With the redesign and maintenance support of Dürr, the system could also - be adapted to other halogenated gases with bricks to be selected according to gas application - cope with the presence of VOCs or contaminated air - larger volumes with the addition of a small lance for 15kg/h liquid injection

Condition: like new (used), Year of construction: 2019, operating hours: 2,611 h, functionality: fully functional, machine/vehicle number: 7621, travel distance X-axis: 650 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 400 mm, spindle speed (max.): 42,000 rpm, total height: 2,900 mm, total width: 2,400 mm, total length: 2,200 mm, table width: 900 mm, table length: 530 mm, type of input current: three-phase, input voltage: 400 V, workpiece weight (max.): 600 kg, distance table to spindle center: 600 mm, input frequency: 50 Hz, number of slots in tool magazine: 30, Equipment: documentation/manual, EXERON HSC 600/3 – a high-speed 3-axis CNC machining center, particularly suitable for the production of graphite electrodes. The EXERON HSC 600/3 is a highly precise 3-axis CNC machining center, designed primarily for machining graphite electrodes. The machine is optimized for high-speed (HSC) machining with high dynamic performance on all axes. The robust construction with a portal and a polymer concrete bed ensures excellent vibration damping, maximum precision, and top-quality surface finish. The machine is equipped with digital drives for all axes, direct measuring systems with a resolution of 0.0001 mm, a high-frequency spindle for HSC machining, and a Heidenhain TNC 640 control system. Thanks to its compact dimensions, it offers a minimal installation footprint and excellent accessibility for operation and automation. Hodozrhd Sspfx Ak Ujnu The machine is in excellent technical condition, has been used very little, and is ready for immediate deployment in production.

Condition: excellent (used), Year of construction: 2024, operating hours: 1,200 h, functionality: fully functional, Offered: Sinker EDM machine genius750NOVA + connection Chameleon Linear - 120 electrode positions - 6 pallet positions 400x400 Sinker EDM machine genius 750 NOVA Right-hand configuration Control panel on the right, automation possible from the left side! * Travel ranges X * Y * Z: 420mm * 420mm * 400mm * Work table: 600mm * 600mm * Work table T-slots: number / width / spacing: 6 slots / 10mm / 83/100/100/100/83 * Controlled C-axis with n = 45 1/min * High retraction speed due to acceleration of 10 m/s² in Z and 20 m/min travel speed Generator * genius IPMtec, with comprehensive technology package for graphite, copper, and tungsten copper for machining all materials commonly used in tool and mold making * max. working current 52A, optional 100A or 196A (with 96A booster) Control system * Internal control computer with 1.2 GHz RISC CPU, 64-bit * Industrial PC with user interface, based on Win 10 * 22“ touchscreen, keyboard, mouse and handheld unit for setup with joystick, handwheel and touch display * Connections: LAN, USB, RS-232 Connection values * Electrical: 6 kVA, 400V, 50Hz * Pneumatic: 6 bar, 10 l/min * Required cooling capacity: 4.5 kW for cooling of dielectric fluid and control cabinet Chameleon base unit Hedpfx Aszzawpjk Uonu consisting of: * Robot * ZK’s own robot controller * 1 guide rail * 1 base magazine without magazine levels with rack and pinion drive Chameleon expansion magazine including base plate and glass sliding door set (magazine positions not included)

Condition: good (used), Dust extraction unit, extraction system, self-cleaning vacuum filter, absorber, dust collector for extracting graphite, metal, mineral, hard fiber, flammable, hazardous, and toxic dust, and for the effective collection of process dust, blasting dust, sanding dust, grinding dust, polishing dust, and all types of dry dust. The extraction unit has explosion hazard classes ST1 and ST2. The vacuum fan is located behind the filter on the clean air side, which minimizes the risk of explosion. Filter cartridge – multi-pocket design. 11 kW fan in a sound-absorbing housing. Capacity: 3500 m3/h. Vacuum: 7000 Pa. Filtration area: 24 m2. Automatic filter cleaning with an electric motor. The extraction unit was used during graphite processing. Hnodpfx Aeg Rhfbek Usu

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, number of chambers: 1, actuation type: electric, Equipment: CE marking, documentation/manual, Stock item, immediately available -Tmax 1350°C -Usable space L x W x H (mm) 600 x 500 x 500 -Batch weight 300 kg -External dimensions L x W x H (mm) 4200 x 2500 x 3500 -Space requirement L x W x H (mm) 5000 x 5000 x 4000 -Weight (net) 13000 kg -Total connected load 125 kVA -Connection voltage 400 V -Current fuse rating 250 A -Control system: Stange SE 607 -Documentation Included: -Protective gas buffer tank -Vacuum pump stand -4-flap design for cooling, allowing the flow direction of the gas stream to be adjusted horizontally or vertically. Hedjzr U Anopfx Ak Usnu -There is the possibility of connecting a liquid nitrogen supply, allowing the furnace to cool down to -80°C. -Internal insulation made of graphite hard felt, CFC-protected and reinforced. We will build a second identical furnace by the end of the year. You can find the detailed description as a PDF in the advertisement! We offer new and used industrial furnaces. Inspection in our warehouse by appointment! Industrial furnace, vacuum furnace, vacuum furnaces, vacuum hardening furnace, hardening furnaces, sintering furnace, sintering furnaces.

Condition: excellent (used), Year of construction: 1992, Wide Belt Sander VIET Target 211 A Calibration and fine sanding machine with 2 sanding units and one motor, sanding from above Working width: 1100 mm Abrasive belt dimensions: 2200 x 1130 mm Workpiece dimensions: 4 – 160 mm Motor for table height adjustment: 0.18 kW, 400 V, 50 Hz Main motor: 8.0 kW, 400 V, 50 Hz 2 feed speeds 1st unit: Rubber-coated sanding roller, 90 Sh, 2nd unit: Fixed sanding pad & air cushion sanding pad, timer controlled Compressed air requirement: approx. 6 bar Extraction connection diameter: 2 x 150 mm Approx. dimensions (L x W x H): 1700 x 1750 x 1800 mm Weight: approx. 1,400 kg Automatic workpiece thickness adjustment with digital display Workpiece thickness adjustment via foot pedal Automatic conveyor belt centering Abrasive belt oscillation Abrasive belt (emergency) stop with disc brakes Table extension with 2 rollers at infeed and outfeed Emergency stop Main switch Hnsdpfx Akey Exhws Uju CE compliant INCLUDES many sanding belts INCLUDES 2 pcs newly covered graphite sanding pad inserts NEW bearings for return rollers NEW drive belts for the motor Note on used machinery: • Errors in technical specifications and prior sale excepted. • Stated prices are ex works - free loading! • Machines have been cleaned and tested for functionality. • All machines are sold as inspected, without any claim to warranty. Buyers are welcome to inspect the machines on site. • Special arrangements are only possible in writing. (Enquiries are only answered if you provide your address and telephone number!)

Condition: like new (used), Year of construction: 2025, Holzkraft Edge Sanding Machine Model: KSO 200 F with veneer sanding equipment Sanding unit tiltable up to 45° via lever The machine frame is made of welded steel, ensuring high torsional rigidity and vibration-free operation. Oscillating sanding belt with separate geared motor for improved sanding results Oscillation can be activated as needed Sanding shoe with graphite coating for extended belt life Height-adjustable sanding table to utilize the entire sanding belt width Height-adjustable auxiliary table with extraction for sanding radii Spring-loaded belt tension automatically compensates for belt length variations Double extraction system Extendable roller table extension With rubber-coated sanding drum Veneer edge sanding device with fine-adjustable contact shoe, pressure rollers, and stop rulers Infeed ruler with groove for overlapping veneer Quick changeover from veneer edge to solid wood sanding possible Dimensions and Weights Length approx. 1900 mm Width/depth approx. 900 mm Height approx. 1350 mm Weight approx. 290 kg Dust Extraction Connection Suction nozzle diameter 140 / 100 mm Drive Power Oscillation motor 0.25 kW Working Tables Working table length 960 mm Working table width 350 mm Hsdpfx Akjy Iu N Ao Ujnu Working table height adjustment 230 mm Height min. 735 mm Height max. 965 mm Longitudinal table height adjustment 230 mm Cross table length 330 mm Cross table width 330 mm Cross table height min. 720 mm Cross table height max. 900 mm Cross table height adjustment 180 mm Electrical Data Main drive motor power 3.0 kW Connection voltage 400 V Sanding Unit Abrasive belt length 3000 mm Abrasive belt width 200 mm Belt speed(s) 20 m/s Sanding surface length 1050 mm Sanding surface width 200 mm Oscillation stroke 20 mm Location: Ex stock 54634 Bitburg — Immediately available —

Condition: defective spare-parts repository (used), Year of construction: 2004, functionality: not functional, travel distance X-axis: 800 mm, travel distance Y-axis: 700 mm, travel distance Z-axis: 500 mm, For sale are spare parts from a 3-axis CNC machining center of the brand Ingersoll, model OPS 800. Ideally suited for the production of graphite electrodes thanks to its high-speed spindle. The machine has been disassembled, and individual components such as the controller, extraction system, spindle, and control panel are available for sale. Please let us know which parts you require, and we will provide you with a tailored offer. Technical Data: Year of manufacture: 2004 X-axis travel: 800 mm Y-axis travel: 700 mm Z-axis travel: 500 mm Control system: ANDRON Spindle speed: 42,000 rpm Tool changer: 36 positions Tool holder: HSK 63 Included: - Graphite dust extraction system - Chip trays - Cooling system Tooling not included. Transport and loading can be organized throughout Europe upon request and at an additional cost. All prices are subject to VAT. Hnsdpfx Ajuu Rthjk Uou Inspection is possible by appointment. Please contact us—our team will be happy to assist you. Trade-ins or exchanges possible! Machinery Purchase / Sales PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MORE. Are you looking for a high-quality but affordable metalworking machine for your production? Or do you want to sell yours? For further information or to contact us, please visit our website.

Condition: like new (used), Year of construction: 2003, TECHNICAL SPECIFICATIONS X axis travel: 1,500 mm Y axis travel: 750 mm Z axis travel: 500 mm Worktable height: 820 mm Open height (clearance): 920 mm Maximum workpiece weight: 100,000 N Maximum load on head: 4,000 N Tank type: Fixed Tank dimensions: 2,300 x 1,300 x 700 mm Worktable size: 1,700 x 1,000 mm Usable dielectric height: 620 mm GENERATOR Standard minimum surface finish: VDI = 0 Power: 60 A MACHINE EQUIPPED WITH Generator with 120 A Expert System Fixed worktable 1,700 x 1,000 mm CNC for simultaneous axis control Integrated ONA C-axis with automatic System 3R Macro Standard chuck Eco-friendly filter with automatic cleaning cycle Dielectric temperature control system Year of manufacture: 2003 MACHINE FEATURES Fixed-table structure ensuring stable operating conditions, equipped with leveling supports Stabilized grey cast iron structure (base, column, tables) X-Y-Z movements via high-precision class A ball screws, driven by three DC motors Motion on prismatic roller guideways Position detection via linear glass scales Improved front accessibility with retractable front door system Fixed working tank Integrated C-Axis (mounted on the head) Maximum speed: 40 rpm Resolution: 0.001° Maximum load (static C-axis): 500 N Hjdpfjxwma Aex Ak Ujnu Maximum load (dynamic C-axis): 120 N Heidenhain encoder Toothed belt transmission Maximum current without rotation: 120 A Maximum current with high-speed rotation: 60 A Maximum current with slow rotation (0–1 rpm): 12 A Moment of inertia: 2,000 kg/cm³ GENERATOR FEATURES Modular design Programmable parameters Maximum power: 60 A EXPERT SYSTEM Controls the entire erosion cycle, from roughing to final surface finish, automatically adjusting spark parameters to ensure maximum generator efficiency and highest machining speed. Dedicated software for deep ribs Dedicated software for finishing large homogeneous surfaces Fully unattended machining capability with maximum productivity and excellent final quality Process parameter monitoring via screen and control panel display Automatic anti-collision system preventing electrode damage in case of accidental contact with the workpiece TECHNICAL DATA Pulse duration (Ton): continuously adjustable from 1 to 6,500 microseconds Pulse interval (Toff): continuously adjustable from 1 to 6,500 microseconds Copper electrode volumetric wear: 0.2% Graphite electrode volumetric wear: 0.1% Surface finish Ra (CLA): 0.1 micron – VDI = 0 Maximum material removal rate: 600 mm³/min Power consumption: 10.7 kVA Current intensity: adjustable from 1 to 12 (manually or via program) Highly sensitive servo control system High erosion stability

Condition: used, Year of construction: 2021, - Working width 1,350 mm - Belt feed speed 2 to 16 m/min - PRO SAND electronic control Automatically Calibrating Sanding Machine Manufacturer: SCM Type: DMC system Year of manufacture: 2021 Technical data - Working width 1,350 mm - Belt feed speed 2 to 16 m/min - PRO SAND electronic control - PLC terminal with 10.4" LCD color display Unit 1 TIE 5000 working unit for additional table, internal cross-padding - Sequencing system of the unit for belt change by only one machine operator - Automatic brake - Linear blower with timed activation for belt cleaning - Belt dimensions: 150 x 5,000 mm - Chevron belt dimensions: 140 x 4,710 mm PE16T EPICS electronic sector sanding, pitch 16 mm - 16 mm distance between sectors from center to center - Double-acting pneumatic cylinders with adjustable feed/counter feed - Graphite cloth with quick extraction device - Complete management of functions via the electronic Pro Sand control - Motor with inverter power up to 15 kW Unit 2 DO19 orbital unit for 19 rotating disc brushes - Manual adjustment of the unit's working position - 1.1 kW main motor with inverter drive - Independent motor for controlling the orbital movement - Diameter of the rotating disc: 125 mm FT/19/125 Set with 19 rotating discs, diameter 125 mm Unit 3 BF300 working unit for brush roller, diameter 300 mm - Manual adjustment of the roller's working position - 4 kW main motor with inverter drive FT 300 brush roller, diameter 300 mm Unit 4 BF300 working unit for brush roller, diameter 300 mm - Manual adjustment of the roller's working position - 4 kW main motor with inverter drive FT 300 brush roller, diameter 300 mm Unit 5 SC 2620 working unit for super finish pad - Rotation of the belt in the opposite direction of the conveyor belt - Electronic belt swiveling control - Disc brake - Chevron belt dimensions: 1,370 x 2,186 mm - Belt dimensions: 1,370 x 2,620 mm PE16/C EPICS electronic sanding block with sector pitch 16 mm - 16 mm distance between sectors from center to center - Double-acting pneumatic cylinders with adjustable feed/counter feed - Graphite cloth with quick extraction device - Complete management of functions via the electronic Pro Sand control - Inverter motor with a power of up to 15 kW Hnodpfxezuzbce Ak Ueu Inverter-controlled vacuum motor integrated into the machine frame, up to 7.5 kW - Rubber-coated conveyor belt, 50 Shore - 4 kW conveyor belt motor with inverter drive Console with integrated PC eye-M and electronic Maestro Pro Sand control with tele service system Device connected to the machine that enables the use of the Maestro Pro Sand software. The integrated LED light strip enables the operator to monitor the machine's status in real time (emergency, operation, etc.) without having to be near the machine itself. It is equipped with a fanless industrial PC with protection class IP53 (IP65 on the front). This robust solution guarantees the highest level of resistance even under the most adverse environmental conditions that an industrial site can offer. The 21.5" LCD color display with a large 16/9 touchscreen enables particularly easy and efficient control of the machine's most important functions: - Full HD display resolution 1920x1080 - LED backlight - Capacitive

Year of construction: 2011, condition: used, The LECO TC-400 ON analyzer is a highly precise laboratory instrument for determining the oxygen and nitrogen content in solid samples. This system is typically used in metallurgy, materials testing, research, and quality assurance, providing reliable elemental analysis for a wide range of inorganic materials. Hodpfxszkaa Ae Ak Usnu The TC-400 operates as an inert gas fusion analyzer (ON/O-N analysis) and enables: Determination of oxygen (O) and nitrogen (N) in solid samples Analysis of metals, alloys, ceramics, and powder materials Highly precise measurement through fusion extraction in a graphite crucible Automated sample loading (depending on the configuration) Evaluation via integrated analysis software Repeatable results for quality and process control Documentation and data management via TCWin Analysis Software (Version 4.24) Thanks to its robust LECO technology, the TC-400 offers stable performance, high measurement accuracy, and a proven analytical platform for demanding applications in research and industry.

Condition: used, Opal Type: Opal 460 Opal 460 by ATM The Opal 460 is a fully hydraulic, water-cooled hot embedding press for embedding polished samples. The process sequence is carried out automatically. The fully automatic sliding shutter enables smooth opening and closing of the embedding area. Manufacturer: ATM Q Ness GmbH Model: OPAL 460 Operating principle: The Opal 460 is a fully hydraulic, water-cooled hot embedding press for embedding polished samples. In hot embedding, the sample is embedded in an embedding press under temperature and pressure with a plastic granulate. The advantages of the process are the high hardness of the embedding media (e.g., glass fiber reinforced) and the good gap-free embedding. Hot embedding media are available based on epoxy resin, acrylic resin, phenol resin, and graphite resin. Main application area: Embedding the samples for better sample preparation for further metallographic examinations. Technical data: Press mold diameter: Ø 30 mm, Ø 50 mm Temperature range: 20 ... 200 °C Max. pressure: 310 bar Weight: ~ 40 kg Hnsdpfx Akezh D Avj Usu Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: like new (used), Year of construction: 2025, travel distance X-axis: 1,000 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 500 mm, table width: 800 mm, table length: 1,200 mm, Machine type: Sinker EDM Manufacturer: ONA Model: IRIS6 Year of manufacture: 2025 Condition: Like new – demonstration machine. Technical data Travel range of the X-axis: 1000 mm Travel range of the Y-axis: 600 mm Travel range of the Z-axis: 500 mm Table length: 1200 mm Table width: 800 mm Description Demonstration machine in the showroom – not used in a production cycle. Ona Iris 6 X: 1000 mm Y: 600 mm Z: 500 mm C-axis 360° Positioning resolution: 0.001 mm XYZ positioning resolution: 0.0001 mm Feed rate: 3000 mm/min Feed rate: 18000 mm/min Hnedpfxey D R Sfj Ak Ueu Working tank dimensions: 1700*1000*600 mm Door type: automatic drop-down door Table dimensions: 1200*800 mm Maximum dielectric height: 565 Maximum workpiece height: 515 Distance between the head and the table without the C-axis is 800 mm, and with the C-axis – 760 mm Maximum electrode weight: 50 kg Maximum table load: 4000 kg Machine dimensions: 3300 x 3370 x 2930 mm Machine weight: 7400 kg 21-inch color TFT touchscreen display Generator: 100 A Maximum material removal rate with copper mm3/min: 550 Maximum material removal rate with graphite mm3/min: 660 Volumetric consumption of copper: < 0.10% Volumetric consumption of graphite: < 0.05% Filtration system: environmentally friendly ONA filter with long service life and no cartridges – self-cleaning Flushing: through the central tool holder / tank – both programmable in the range of 1–31 Additional equipment installed on the machine: - precision pressure rulers - central automatic lubrication system - C-axis + automatic Erowa ITS 100 chuck - machine head prepared for fume extraction - 9-position automatic tool changer - CNC access to shared files in Windows networks - file sharing of machine files in Microsoft Windows networks - 1650 liters of ONA dielectric fluid - ISL function – online diagnostics - dielectric cooler matched in performance to the 100A generator - 3 mm measuring probe

Condition: used, Year of construction: 2007, total height: 2,800 mm, total length: 3,000 mm, total width: 2,500 mm, overall weight: 8,300 kg, Mikron HSM 800 – High Speed Machining Center Year 2007 | Heidenhain iTNC 530 | 24,000 rpm | 3-pallet changer High-precision CNC machining center from Mikron / GF AgieCharmilles, designed for demanding HSC applications such as mold & die, graphite and electrode machining, as well as flexible production. Travels: X 800 mm / Y 600 mm / Z 500 mm with pallet size 800 x 600 mm. Equipped with a 3-pallet changer for efficient automated operation. The machine features a high-speed spindle up to 24,000 rpm with HSK-A63 interface and a 50-position tool magazine. Well equipped with high-pressure through-spindle coolant (18–70 bar) including band filter system, chip conveyor, minimum quantity lubrication, oil mist extraction, rotating viewing window and probing system (M&H). Additional features include APS (Advanced Process System) and ITC (Intelligent Thermal Control) for maximum process stability and thermal accuracy. Control: Heidenhain iTNC 530 Spindle speed: 24000 - rpm Travel Y-axis: 600 - mm Dimensions of the clamping surface: 900 x 600 mm Travel Z-axis: 500 - mm Travel X-axis: 800 - mm Hsdpfsy Tkc Ajx Ak Uonu Dimensions (LxWxH) approx.: 3000 x 2500 x 2800 mm Weight approx.: 8,300 kg Year of construction: 2,007 Condition: in working order Terms of payment: 100% prepayment before pick-up Terms of delivery: From foundation under power: Yes

Condition: like new (used), functionality: fully functional, Year of construction: 2022, operating hours: 29 h, roller diameter: 90 mm, sheet thickness steel (max.): 2 mm, overall weight: 520 kg, power: 1.1 kW (1.50 HP), working length: 1,270 mm, For sale is a like-new round bending machine with only 26 operating hours! TECHNICAL DETAILS Work area Working length: 1,270 mm Sheet thickness at 450 N/mm²: max. 2.5 mm Sheet thickness at 700 N/mm²: max. 1.5 mm Sheet thickness for conical bending of steel sheet: 2 mm Roller diameter: 90 mm Roller speed: 6 m/min Diameter of feed grooves: 4 / 6 / 9 mm MACHINE DETAILS Motor power, main drive: 1.1 kW Dimensions & Weight Dimensions (L x W x H): 1,850 x 700 x 1,200 mm Weight: 520 kg EQUIPMENT 3-roller round bending machine with asymmetrical roller arrangement Robust machine frame made of spheroidal graphite cast iron Induction-hardened rollers, also suitable for processing stainless steel Main motor with braking system for precise bending Hedpfsz Dw Emsx Ak Ujnu Swiveling top roller with eccentric locking for easy workpiece removal Wire feed grooves on the lower and rear rollers Conical bending device Manual adjustment of the rear roller Separate mobile control console with foot switch for left/right operation Emergency stop safety cable Side cover Operating manual

Condition: used, mileage: 25,000 km, power: 120 kW (163.15 HP), first registration: 07/2025, fuel type: diesel, color: grey, gearing type: automatic, number of seats: 8, total length: 4,895 mm, total width: 2,244 mm, total height: 1,910 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, * 2-way speakers front and rear * Comfort 3-seater bench, 1st row, outer seat foldable * Comfort 3-seater bench, 2nd row, outer seat foldable * 9G-TRONIC automatic transmission * Adaptive brake light * Aerodynamics package * Passenger airbag * Active Brake Assist * Active door retainer for sliding door * Active Lane Keeping Assist * Acoustic package * Trailer load capacity 2500 kg * Detachable ball-type trailer coupling * Armrests for passenger area seating * Exit lights * Electrically folding exterior mirrors Hjdpfx Akey Nvg Ee Uonu * Heated and electrically adjustable exterior mirrors * Lighting in rear grab handle with reading spotlight * Illuminated vanity mirrors * Front footwell lighting * BlueEFFICIENCY package * Brake force booster failure compensation * CO2-optimized braking system * Chrome interior package * Privacy glazing in rear, tinted glass * DIGITAL RADIO (DAB) * Roof cladding * Double cup holder in center cockpit * ECO start/stop function * EMISSION CLASS EURO 6E UP TO M1 * Automatic headlamp control * Misfuelling protection * Fixed rear window * Tailgate window with wiper and washer system * Front right window, fixed in side wall/sliding door * Front left window, fixed in side wall/sliding door * Electric parking brake * Speed limiter 210 km/h * Weight variant 3,100 kg * Belt warning for front passenger seat * HOLD function * Entry grab rails for driver and front passenger * Main tank 70 liters * Interior and ambient lighting for combi * Automatically dimming interior mirror * Premium interior trim * COMBI VEHICLE * Passive child detection in vehicle * Child safety locks for rear passenger doors * Semi-automatic climate control, TEMPMATIC in rear * Automatic climate control THERMOTRONIC * Instrument cluster with color display * Comfort front passenger seat * Comfort roof control unit * Comfort driver seat * Comfort suspension * Comfort closing * Communication module (LTE) for digital services * PAINT COLOR GRAPHITE GREY METALLIC DARK MB 7831 * Leather steering wheel * Live Traffic Information * Lumbar support driver and passenger seat * MBUX multimedia system * MULTIBEAM LED with High Beam Assist PLUS * Mercedes-Benz MobiloVan with DSB and GgD * Mercedes-Benz emergency call system * Metallic paint * Center console with storage compartment * Multi-button remote control * Multifunction steering wheel * Rear compartment night lighting * Navigation system * OM 654 DE 20 LA 120 kW (163 hp) 3800 rpm * Breakdown management * Parking package with reversing camera * Wheelbase 3200 mm, long rear overhang * Wireless tire pressure monitoring front and rear axle * Sliding door left * Tail/brake/blinker lights in LED technology * Face-to-face seat mounting 1st rear seat row, rails * Driver seat occupancy detection * Heated passenger seat * Heated driver seat * Seat cushion depth adjustment passenger seat * Seat cushion depth adjustment driver seat * Quick-release seat rail system * Smartphone integration package * Vito Mirror Package * 12V socket in boot/cargo area * 12V sockets for rear passenger rows right & left * Fabric Caluma black * CRUISE CONTROL * Thorax-pelvis sidebag passenger * Thorax-pelvis sidebag driver * Blind Spot Assist * Tourer SELECT * Ambient lighting for tailgate * Traffic Sign Assist * Front axle with increased load capacity * Preparation for Remote Services Plus * Warm air duct to passenger compartment * Heated Wet Wiper blades * Window airbags for driver and front passenger * All-round heat-insulating glass * Electric auxiliary heat