Used Mineral Wool for sale (320)

Condition: like new (used), functionality: fully functional, Year of construction: 2025, operating hours: 55 h, Machine with special rotor available immediately Advantages: + special rotor with reduced blade overhang, suitable for hard and soft materials + 22 kW motor + effective square blades *for pallets: up to a maximum of 10 pallets per hour *dependent on screen size and material. With smaller wood residues, significantly more. Motor: 22 kW; 400 V - 50 Hz - 3 phase, Screen: 15/20 mm or as agreed (10 to 40 mm possible) hydraulically operated slide Screen opening currently (15/20 mm) *can be exchanged Extraction nozzle Ø 200 mm. Feed opening 1000x1000 mm Dimensions: 2000x1800x1645mm Example image above: color of the system may vary Weight: 1920 kg. Included as standard: - Control cabinet with PLC control - automatic star/delta start - fast hydraulics - auto. OFF when the rotor is idle - speed 70-90 rpm for high throughput - cycle control to avoid idle times - performance-enhancing step control of the hydraulic slide - Pertinax guides for hydraulic slide - vibration-damping machine feet - CE compliant The following options are available at an extra cost: - Raise shredder by 30 cm (preparation for conveyor belt) + €2,480 net - Inclined conveyor belt (discharge height approx. 220 cm) + €12,980 net - Overband magnet + €6,980 net - Control for conveyor belt and overband magnet + €2,750 net Isdpfx Asx Af Rdobvoau (Start and stop synchronized with the shredder) - extended feed hopper 1500x1500 mm + €3,480 net Requirements for the raw material: - The moisture content (as received) must be below 25% - The feed must be free of metals and mineral contaminants. Damage to the tools and/or increased wear may result.

Condition: as good as new (ex-display), Year of construction: 2025, Special price for our demonstration machine Another machine, available now (ex works in Neckartailfingen) Approx. 8 operating hours. Suitable for shredding all types of leftover wood and also pallet sections. The pallet would need to be prepared with a jigsaw or chainsaw so that it fits vertically into the hopper - see Figure 2. Ideally, it would be approximately 40x20x20 cm so that the wood can lie flat on the slider floor. This is where the machine works most effectively. A hydraulic slider runs at the bottom of the shredder, which pushes the wood against the rotor depending on the load. The material is shredded until it passes through the screen basket. Throughput up to 200 kg per hour *depending on the screen and how well the material is prepared. *Conveyor belt and overhead magnet available at an additional cost. + Powerful 18.5 kW motor, + Concave blades, + Large high-performance gearbox, + Special, load-dependent slide control, Customs tariff number: 84659600 Motor: 18.5 kW; 400 V - 50 Hz - 3 phase Blades: 15, multi-rotatable Option: double row of blades + €995 net Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Cutter opening: 630 x 820 mm Iaedjdwktkopfx Abveu Filling volume: approx. 0.6 m³ Hydraulic slide gate Screen perforation of your choice (10 - 30 mm) Suction nozzle diameter: 160 mm Weight: approx. 1,300 kg (depending on accessories) Dimensions (L x W x H): approx. 1,737 x 1,167 x 1,650 mm Moisture content: 30% dry Included as standard: - V-rotor for maximum throughput - Control cabinet with Siemens PLC control - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idling - Speed 70-90 rpm for high throughput - Cyclic control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant. - MADE IN GERMANY . Shredder options: - Raise shredder by 30 cm (prepared for conveyor belt) +€2,080 net - Articulated conveyor belt +€8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet +€5,980 net - Conveyor belt and overbelt magnet control +€2,750 net (Start and stop synchronized with the shredder) - Extend hopper +€940 net - Eco-rings: +€1,980 net (recommended for more than 15% hardwood) - Special scraper +€990 net (recommended for veneer or paper) - Double Knife series + €995 net . Raw material requirements: - The moisture content (dry) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear.

Condition: good (used), Used machine, good condition. Delivery time appr. 16 weeks after ordering Basic machine starts at 139.700 € net *Options at additional cost, see below Briquetting press e.g. for wood dust, spelled husks, activity material (e.g. for pigs to play and nibble around), animal feed, lucerne or wood shavings. *Optionally, short briquette tablets can be made Technical specifications: Throughput capacity up to a maximum of 750 kg/h (depending on the material) (e.g. sawdust with a bulk density of 250 kg/qbm) An exact statement about the throughput is only possible after a test with your material. Can vary greatly depending on the bulk density of the starting material. Goods tariff number: 84793010 Briquette Ø 65 mm including 2 m press channel Engine power main engine 37 kw Feed screw geared motor 2.2 kw Compressor screw 5.5 kw Hydraulic pump motor 0.37 kw Total connection value: approx. 47 kW Control panel with plain text display for operating states and utilization indicator for the main drive and feed screws PLC control with operating hours counter in the control cabinet Machine has CE mark Automatic start-stop function Dimensions 3100x860x1800 mm lxwxh Weight 3800kg Options at extra cost: Temperature control unit for the pressing tools to maintain the temperature for optimal briquette quality. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - absolutely necessary for operation including the corresponding control + €7,850 net guillotine or pill crusher, for cutting the briquettes to length + €6,900 net Necessary for compressed air connection! Silo for MAP series + €19,940 net Iaodpfx Abefmqq Ejveu - Storage silo above the machine - Content approx. 6 sqm, stable steel construction with agitator discharge and level indicator. Transport line / cooling section (nominal value: 4x2m) each 2 meters 990 euros net Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site) according to expenditure on proof against separate calculation. The following sentences apply: Service technician/mechatronics technician per hour of assembly and travel: €129.00 Overtime: 25% surcharge 50% surcharge for each Saturday and night hour 100% surcharge for each Sunday and holiday hour Release per mechanic per day: depends on the country Per car and van and driven kilometer: 0.98 € / km Arrival and accommodation against receipt or flat rate billing at the expense of the client. . Test with the respective customer material: (by arrangement, up to a maximum of 750 kg) - 1,970 € net . Raw material requirements: - The moisture content (atro) must be between at least 6 and a maximum of 15% - Maximum chip length 18 mm - Installation temperature: room with a temperature of at least +5°C - The charge must be free of metals and mineral impurities. This can result in damage to the pressing tools and/or increased wear

Condition: reconditioned (used), Year of construction: 2023, All wear parts new only 704 operating hours Special price for a low-hour demonstration unit Base machine: €29,990 net Optional extras (for an additional charge): - Cooling unit: €3,995 net - Emulsion tray: €3,990 net The hydraulic briquetting presses of the MPP NEM series compact materials such as aluminum, copper, brass, bronze, graphite, and other non-ferrous metals into dimensionally stable cylindrical briquettes. These machines are distinguished by their robust construction, ensuring consistent briquette quality during continuous operation. The pressing process does not require any binding agents – compaction is achieved solely through hydraulic pressing force. Depending on material, the feedstock volume can be reduced by up to 90%. Throughput capacity: maximum 70 kg/h (depending on material) Briquette diameter: Ø 50 mm Motor: 5.5 kW Iedpfxsd N Dnhe Abvoau 400 Volt / 50 Hz / 3-phase Pump: 40 liters Maximum briquette length: 50 mm Optimal briquette length: 40 mm Silo diameter: 1,000 mm Oil tank: 110 liters Dimensions: 1750 x 1130 x 1100 mm (L x W x H) Weight: 950 kg Hydraulic pre-compaction via slide Main press cylinder Vertical cylinder Fill level sensor: yes Feed material requirements: - Max. chip length: 15 mm - Installation room temperature: heated space, at least +5°C - Max. load on agitator: 150 kg - Feed material must be free from magnetic metals and mineral contaminants such as sand, stones, etc. Damage to pressing tools and/or increased wear may otherwise occur.

Condition: new, Year of construction: 2026, Production time of the machine approx. 3.5 months Very robust machine with high pressing force - is also suitable for producing a saleable briquette quality *depending on the material. The large press cylinder and the 65 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to faults + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Good price-performance ratio Options: Surcharge for cooling unit + € 3,995 net, (can also be retrofitted later) * cools the press tongs (important from 3.5 hours) and the hydraulic oil * Cooling unit recommended for regular operation of more than 3.5 hours at a time. Large pre-compressor chamber + € 1,975 net recommended for light starting materials such as wood shavings Product code: 84793010 Briquette diameter: 65 mm Front bush: 65 mm Briquette stroke max.: 50 mm Briquette stroke opt.: 50 mm Output (depending on material): up to 110 kg/h* approx. 87 kg/h in the last test. *depending on the bulk density *based on a bulk weight of 200 kg per cubic meter . Motor power: 5.5 kW 400 Volt / 50 Hz / 3-phase Length: 1925 mm Width: 1100 mm Height: 1500 mm Weight: 800 kg Oil volume: 110 liters Iaodjffh Atjpfx Abvou Silo diameter: 1000 mm Silo capacity: approx. 0.7 qbm Pump: 37 liters Hydraulic pre-compressor Cooling press tongs option: yes, with special accessory Coolable press tongs Cooling of the pressing tongs via water tank (to be procured on site) Hydraulic oil cooling option: yes Fill level monitoring option: yes Briquette option: yes (depending on material) CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18 % - Chip length maximum 15 mm - Installation temperature: tempered room at a minimum of +5°C - The feed must be free of metals and mineral impurities such as sand, stones, etc. Damage to the pressing tools and / or increased wear may result

Condition: new, Year of construction: 2026, The ideal machine for shredding softwood. Motor: 11/15 kW; 400 V - 50 Hz - 3 ph, Rotor diameter: 260 mm, Hydraulically actuated pusher Screen perforation to choice (12 - 40 mm) Extraction port Ø 160 mm Weight approx. 1,100 kg Dimensions (LxWxH) approx. 1805 x 1118 x 1650 mm Colour: blue / grey Requirements for raw material: - Moisture content (atro) must be below 30% - Metal and mineral contaminants such as sand, stones, etc. lead to increased wear. Isdpfx Abowzarcsveau We are pleased to offer a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material by freight and we will document the test with photos and videos.

Condition: like new (used), Year of construction: 2024, operating hours: 29 h, *one machine is ready for delivery and ready produced Press can only be supplied with a system component such as a chipper, cutting mill, hammer mill, screw conveyor, conveyor belt with overbelt magnet or suction RUF briquetting press for rectangular briquettes Very robust and established machine The ideal machine for professional, industrial briquette sellers. Classic type - throughput up to 425 kg / h * depending on the material Options for an extra charge: Plant construction / mütek system technology: - mütek shredder MRZ shredding technology - conveyor belts - Overbelt magnets - Extraction systems, optionally with rotary valve - screw conveyors - silos - Control links of all kinds - semi-automatic packaging technology Press: - Packing table with drawer - Top-mounted silo with discharge Your advantages: Most important point: + Very established, well-engineered die press thanks to 25 years of experience. The difficulty and the know-how lies in the detail. For example, valves and cylinder seals of the highest quality. + 24h operation possible + Longevity + Low maintenance costs + Compact structure Ijdpofhql Tefx Abvoau + High energy efficiency thanks to innovative hydraulics Technical data briquetting press: Throughput: up to 425 kg / h * * depending on the bulk weight of your raw material * based on a bulk weight of 200 kg per cubic meter Detailed information after a successful test with your material. If no test material is made available to us, we cannot make any statements about the briquette quality and throughput. Briquette dimensions: 150 x 60 mm Briquette length: 40 to 105 mm (adjustable) Hydraulic pre-compressor Main hydraulic compressor Pressing pressure: up to approx. 1700 kg / cm² Hydraulic system with 260 liter oil tank Pump motor: 30 kW / 400V / 50Hz / 3 ph Manual operation of all cylinders "Dustproof" switch cabinet with PLC control and touch display Total power consumption of the briquette press: approx. 33 KW Muxzr8 Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 15% - Maximum chip length: 20 x 2 x 2 mm - temperature where machine is placed + 8 degrees - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear.

Condition: new, Year of construction: 2026, Single-shaft shredder MRZ 530 Iodped Db N Iefx Abveau Included: + Profile rotor for increased throughput Options: Double knife row + €895 net Veneer and paper stripper + €970 net * recommended for extremely thin materials with a thickness less than 3 mm Our mütek single-shaft shredder MRZ 530 processes a wide variety of materials such as all types of wood residues, softwood, chipboard and MDF, pallets, construction timber, demolition wood, carpets, cables, paper, cardboard, and plastics. The machine is characterized by its robust design, ensuring consistent quality in continuous operation. We are pleased to offer you a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via freight and we will document the test with pictures and videos. Machine data: Motor: 15 kW; 400 V - 50 Hz - 3 phase Knives: multiple reversible Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Hopper (mm): 510 x 810 mm Hopper volume approx. 0.4 m³ Throughput: 1 - 5 hopper fillings/hour Hydraulically operated pusher Screen perforation as desired (10 - 40 mm) Extraction nozzle Ø 160 mm Weight approx. 1,000 kg Dimensions approx. 1550 x 1100 x 1640 mm Moisture content of raw material: must be below 30% a.d. Standard features included: • Fast hydraulics • Profile rotor • Control cabinet with Siemens PLC control • Automatic star-delta start • Automatic shut-off in case of rotor idle • Removable extraction channel • Speed 70 - 100 rpm for higher throughput • Cycle control to prevent idle time • Performance-enhancing step control for hydraulic pusher • Stable guides for hydraulic pusher Additional shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Angled conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable 0-60 degrees Discharge height: approx. 2000 mm ± 100 mm - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) Requirements for input/raw material: - Moisture content (a.d.) must be below 30% - Metals and mineral impurities such as sand, stones, etc., lead to increased wear

Condition: new, Year of construction: 2026, Delivery time approx. 3-4 months MRZ 830 Shredder Custom tariff number: 84659600 Feed opening 800 x 1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 ph Blades: multi-rotatable Hydraulically operated slider Screen perforation of your choice (10 - 40 mm) Suction nozzle Ø 200 mm Weight approx. 1,600 kg Dimensions (L x W x H) approx. 2,290 x 1,420 x 1,750 mm Turbo clutch Included as standard: Iedpfed Dgw Uex Abvsau - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 rpm for high throughput - Cycle control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant . The shredder is designed for shredding natural wood, particle board, and MDF, as well as other materials after testing and approval by the manufacturer. Additional shredder options: - Raise shredder by 30 cm (prepared for conveyor belt) + €2,140 net - Articulated conveyor belt + €8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet + €5,980 net - Conveyor belt and overbelt magnet control + €2,750 net (Start and stop synchronized with the shredder) Raw material requirements: - Moisture content (dry) must be below 30% - Installation temperature: temperature-controlled room at least +5°C - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Condition: new, Year of construction: 2025, The ideal machine for shredding hardwood and softwood Another machine now available (ex-works Neckartailfingen). Iasdjd E R D Sspfx Abvou Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Blades: 14+2 pieces, 40x40mm, reversible multiple times, Rotor diameter: 260 mm, Control system: Omron PLC, Cutting chamber opening: 600 x 800 mm, Hopper volume approx. 0.6 cbm, Hydraulically operated pusher Screen perforation of your choice (12 - 40mm) Extraction socket Ø 160 mm Weight approx. 1,300 kg Dimensions (LxWxH) approx. 1737 x 1167 x 1650 mm The following options are available at an additional cost: - Additional row of knives + €1,990 net (28 instead of 14) - Surcharge for segmented floor, 4-sided + €2,170 net (prevents the pusher from jamming. Recommended for materials with a thickness of less than 3 mm) - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Angled conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overband magnet + €5,980 net - Control system for the conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) - Special bearing + €1,540 net (rarely required. Closed, even more robust rotor bearing. May be considered for screens smaller than 15 mm or high fine content. Not necessary if bearings are greased approximately every 2 weeks in operation) Requirements for raw material: - The moisture content (atro) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. increase wear. We are happy to offer a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via freight company and we will document the test with photos and videos.

Condition: new, Year of construction: 2024, production time appr. 4 months * for suction perception, see picture 4 and 5 Tariff number: 84659600 Main motor: 55 kW; 400 V - 50 Hz - 3 ph including turbo coupling, Hydraulic motor: 2.2 kW, 400 V - 50 Hz - 3ph Knife: 76 pieces, rotatable Knife size: 35 x 35 x 20 mm Rotor diameter: 360 mm Control: PLC Siemens S7-1200 Funnel opening approx. 1530 x 1235 mm Hopper volume approx. 2.5 square meters hydraulically operated slide Screen perforation: 10 - 30 mm Extraction nozzle Ø 200 mm Weight approx. 4,500 kg Dimensions (lxwxh) approx. 2765 x 2520 x 1730 mm Turbo coupling Included as standard: - V-rotor for other throughput - 2nd row of knives on the rotor - Control cabinet with Siemens PLC control - automatic star / delta start - fast hydraulics - Automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - Clock control to avoid idle times - Performance-increasing step control of the hydraulic slide - Pertinax guides for hydraulic slides - anti-vibration machine feet - CE conformity Iodpjd Hkqhofx Abvoau The shredder is for shredding natural wood, chipboard and MDF board other materials after testing and approval by the manufacturer Recognition from the raw material: - The moisture content (atro) must be below 30% - Metals and mineral impurities such as sand, stones, etc. Interests to interests wear

Condition: as good as new (ex-display), Year of construction: 2025, Machine for sale at a special price Another machine, available immediately (ex works Neckartailfingen) * Including 1 year warranty. Iaedpfed Nnwlox Abvou Your advantages: + Very robust, simple technology + Top price-performance ratio + Suitable for continuous operation + Long-standing, well-functioning / established machine Including control cabinet with timer operation Press is switched on manually and then runs until the time set on the timer (e.g. 4 hours) has elapsed. Then the press switches off. Technical data: Briquette dimensions: approx. 30 x 30 mm (square), Briquette length: 5-40 mm *depending on material Throughput capacity: up to a maximum of 20 kg/h. *depending on material Machine dimensions approx. 137 x 75 x 148 cm (length x width x height), Weight of the machine: approx. 250 kg, Capacity of the silo: approx. 250 liters, Motor: 2.2 kW, 400 V - 50 Hz, Noise emission: 62 dB, Raw material requirements: -Wood chips and dust smaller than 15 mm in length -Moisture content less than 18 % ATRO -Sand, stones, metals and minerals increase wear --- Options at extra charge: --Timer function + 490 € net Machine is started manually and switches off automatically after a set time X. -Level indicator for automatic operation + 1450 € net Press starts and then stops automatically * NEW !!! Also available in 230 Volt, Motor then 3 kW instead of 2.2 kW, Surcharge + 890 € net (delivery time then approx. 8 weeks) - Special pressing units + 2.950 € net ---

Condition: as good as new (ex-display), Year of construction: 2025, showroom machine machine available Advantages: + special rotor with reduced knife protrusion + Motor 22 kW + effective square knife * for pallets: up to 10 pallets per hour * depending on the sieve and material. With smaller residual wood, significantly more. Engine: 22 kW; 400 V - 50 Hz - 3 ph, Iajdpfx Aedv Eu Hobvju Sieve: 15/20 mm hydraulically operated slide Current screen perforation (15/20 mm) * can be exchanged Extraction nozzle Ø 200 mm. Feed opening 1000x1000 mm Dimensions: 2000x1800x1645mm Example image above: The color of the system may vary Weight: 1920 kg. Included as standard: - Control cabinet with PLC control - automatic star / delta start - fast hydraulics - automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - cycle control to avoid idle times, - performance-increasing step control of the hydraulic slide, - Pertinax guides for hydraulic slides, - vibration-damping machine feet, - CE conform. The following options are available at an additional cost: - Additional row of knives + € 2,790 - segment bottom + € 6,890 (recommended for materials with a wall thickness thinner than 3 mm) - Special K-rotor storage + € 3,480 If necessary, consider shredding plastic with sieves smaller than 15 mm or with a lot of fines. If the bearings are lubricated with grease every approx. 4 weeks in operation, this is not necessary) - Raise the shredder by 30 cm (preparation for conveyor belt) + € 2.480 net - Angled conveyor belt (discharge height approx. 220 cm) + € 12.980 net - Overbelt magnet + € 5.980 net - Control conveyor belt and overbelt magnet + € 2.750 net (Start and stop synchronized with the hacker) - Exhibition hopper 1500x1500 mm + € 3.480 net Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: as good as new (ex-display), Year of construction: 2024, The ideal machine for shredding cables, including optimized cutting geometry, approximately 9 operating hours. Motor: 18.5 kW; 400 V - 50 Hz - 3 phase, Knives: 14 pieces, 40x40mm, multi-rotational, Rotor diameter: 260 mm, Control: Omron PLC, Cutting chamber opening 600 x 800 mm, Hopper volume approx. 0.6 m³, Hydraulically actuated slide Screen hole size optional (15 - 40mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxbxh) approx. 1737 x 1167 x 1650 mm The following options are available at an extra cost: - Double knife row + €1,990 net (28 instead of 14) - Surcharge for four-sided segmented base + €2,170 net (prevents the slide from blocking. Recommended when shredding plastics, paper, veneer with a thickness of less than 3 mm). - Raise the shredder by 30 cm (preparation for a conveyor belt) + €1,980 net - Angle conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overband magnet + €6,980 net - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) Bea9ia3l27 Requirements for the raw material: - Mineral impurities such as sand, stones, etc. lead to increased wear. Iaodpogmfa Ajfx Abvju We would be happy to offer a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material by freight forwarder, and we will document the test with photos and videos.

Condition: good (used), Refurbished machine *Options at additional cost, see below with a full 1 year warranty Ready for delivery approx. 16 weeks after ordering Technical specifications: Throughput up to 1200 kg / h depending on the material (e.g. sawdust with a bulk weight of 150/180 kg / qbm) Briquette Ø 75 mm including 2 m press channel Main motor power 45 kW Feed screw gear motor 2 x 2.2 kw Compressor screw 2 x 5.5 kw Distribution auger 2.2 kw Hydraulic pump motor 0.37 kW Total connected load 65 KW Control panel with plain text display for operating states and utilization display for main drive and feed screws PLC control Siemens S7 / 300 with operating hours counter in the control cabinet Machine hat CE mark Automatic start / stop function of the machine Dimensions 3100x860x1800 mm lxwxh Weight 4500 kg Options: -Silo for MAP series Storage silo above the machine - Contents approx. 6 square meters, stable steel construction with agitator discharge and level indicator. 19,700 € net plus VAT. *only possible for one presse MAP 1200 below the silo if you need to place two machines MAP 1200 below one silo it needs to be build completely different. the price for this silo is 37.900 € net -Temperature control device for the pressing tools to maintain the temperature for optimal briquette size. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - must be left for operation including corresponding control € 7.850 net Oil heater 1.950 € net -Guillotine, to cut the briquettes to length Create a compressed air connection on site € 6,940 net plus VAT -Transport line / cooling section (nominal value: 4x2m) 990 euros net per 2 meters - Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site to install one press) based on effort and upon proof against separate invoice. The following sentences apply: Service technician/mechatronics technician per assembly and hour of travel: €129.00 Overtime: 25% surcharge 50% surcharge per Saturday and night hour 100% surcharge for every Sunday and public holiday hour Iodpfx As E Dqujbvsau Release per fitter per day: country dependent Per car, van and driving kilometer: €0.98 / km Arrival and overnight stay against receipt or flat rate bill at the client's expense. . Test with the respective customer material: (up to a maximum of 750 kg) - €1,970 net flat rate --- Recognition from the raw material: - The moisture content must be between a minimum of 6 and a maximum of 18% - Maximum span 20 mm - Excessive temperature: temperate room at at least + 5 ° C. - The loading must be free of metals and mineral impurities. This and the pressing tools and / or responsible wear can be the result

Condition: good (used), Year of construction: 2025, Requirements: - Material must be free-flowing (less than 18 mm) - Material must be pure, with ash content below 1% ATRO Caution concerning: sand, stones, and mineral content Iedpfxefbb Aro Abvsau - Material is compacted by pressing tongs - Material must be dry, maximum 15% ATRO New: Innovative combination of briquette and pellet Optional upgrades available: Plant engineering / mütek Systemtechnik: - mütek Shredder MRZ size-reduction technology - Conveyor belts - Overband magnets - Extraction systems, optionally with rotary valve - Screw conveyors - Silos - All types of control system integration - Semi-automatic packaging solutions + 24h operation possible + Compact design + High energy efficiency thanks to innovative hydraulics + Achievable briquette density of up to ≥ 1 kg/l *Details after testing Functionality: The machine features a silo with agitator. Each of the four corners of the storage silo contains a vertical screw which compacts the material downward into the press chamber. The machine operates with two cylinders, each pressing in both directions (either as the cylinder moves forward or backward). This produces four briquette outlets, each generating six individual briquettes. *Ideal for automatic feeding of the heating boiler Format: Ø 30 mm Throughput capacity: up to 310 kg/h maximum Motor power: approx. 27 kW (total) Dimensions: 3.1 x 2.3 x 2.2 m Weight: 3.55 tons Your advantages: Compact briquette/pellet format enables fuel feeding of industrial firing plants via screw conveyor Fully automatic 24h operation possible High energy efficiency Briquettes/pellets with consistently high quality and density For automatic feeding into industrial combustion systems Small to medium quantities of wood chips generated in various processing industries (especially wood, biomass, etc.) can be efficiently compacted. The small Ø 30mm format represents an attractive alternative. Unlike our conventional briquettes, these can be fed automatically into industrial combustion systems. In addition to wood, a wide variety of other materials can also be processed without issue (various types of biomass and agricultural residues).

Condition: used, Shredding Machine MGZ 1330, 37 kW Operating hours: 275 Included: - Second knife row - Fast hydraulics for increased throughput - Preparation for conveyor belt Optional: - Conveyor belt with automatic metal separator Your advantages: + Extremely large cutting chamber opening; top: 1300x1200mm + Special rotor suitable for both hardwood and softwood + Energy-efficient and powerful, 37 kW start-up power Technical data: Feed opening, top (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen hole size (mm): configurable Tools: 37/70 knives Extraction connection diameter (mm): 200 mm Iaedpfox Tfdhjx Abvju Dimensions: 2430x2410x1735 mm (LxWxH) Weight (approx. kg): 3,500 --- Feedstock requirements: - The moisture content (atro) must be below 20% - The feed material must be free of metals and mineral contamination. Damage to the tools and/or increased wear may result.

Condition: used, maximum load weight: 31,420 kg, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 05/2023, next inspection (TÜV): 05/2026, loading space volume: 34 m³, total width: 2,550 mm, total height: 3,685 mm, Year of construction: 2023, Equipment: ABS, Kässbohrer Tank Semi-Trailer STC 34 Code L4BH Chemical First Registration Ø Unladen weight: 7,580 kg Ø Stainless steel chassis, polished to a high gloss Ø BPW axles with large disc brakes, 430 mm Ø 1st axle is a lift axle Ø Crank support legs, steel, full-load capable Ø 6 tires, size 385/65 R 22.5 Ø Aluminum rims, ALCOA Dura-Bright, high gloss Ø WABCO trailer EBS with RSS (Roll Stability Support) Ø Tank: 34,000 liters, made of stainless steel 1.4571 (AISI 316 Ti) Isdpfx Abex Rtafovjau Ø Operating pressure 3.0 bar / test pressure 4.0 bar Ø Insulation: 100 mm glass wool Ø Single compartment with 4 baffle plates Ø 5 manhole covers: 3x DN500 and 2x DN350 Ø 1 vent valve by Fort Vale Ø 1 safety valve Ø 1 check valve Ø Air line on right side, DN 50, with TW 50 connection at front right Ø Heating preparation, 4-channel hot water Ø 1 discharge outlet, DN 100 uninsulated, with sampling tap at rear right and TW 80 coupling Ø 1 emptying (cleaning) system Ø Pneumatic bottom valve Ø Hose tubes left and right, DN 150, approx. 6 m long RENTING is the new BUYING – also available from us as a full-service rental.

Condition: good (used), NOVOTEST Impulse Test Stand / High-Pressure Test Stand Sale from site! Manufacturer: NOVOTEST / BLUM-NOVOTEST GmbH Type: Impulse Test Stand System No.: 00318 Version: High-pressure impulse test stand with hydraulic supply and test cell For sale is a used NOVOTEST impulse test stand suitable for industrial applications, test engineering, hydraulics, research, development, and quality assurance. The system was used for dynamic internal pressure testing of hoses, pipelines, fittings, and containers, and features computer-controlled test sequence management. Technical data: Max. operating pressure: 1,500 bar Test medium: Mineral oil / various testing media possible Frequency: 50 Hz Rated power: 135 kVA Operating voltage: 3 x 500 V PEN Control voltage: 230 V~ / 24 V- Pre-fusing: min. 160 A / max. 200 A Impulse volume at 1,500 bar: max. 140 cm³ Impulse volume at 1,000 bar: max. 210 cm³ Additional pressure stage: max. 340 cm³ Maximum test frequency: 1.7 Hz Test fluid temperature: up to max. 160 °C Temperature control accuracy: ± 3 °C Total weight according to nameplate: approx. 6,000 kg Equipment: - Complete industrial impulse test stand - Enclosed test chamber / test cell - Hydraulic power supply - Specimen supply system - Power section - Test cabinet - Operator cabinet - PC-based control system - Pressure and displacement transducers - Temperature control - Flushing system for test media - Safety monitoring / emergency stop - Technical documentation available Hydraulic power unit: - BOSCH hydraulic power unit - Output: 55 kW - Voltage: 500 V / 50 Hz - Tank volume: approx. 840 l - Max. operating pressure: approx. 280 / 315 bar Suitable for: - Pressure impulse testing Iaodpfxoy Rp R Te Abvou - Hydraulic testing - Burst testing - Hose testing - Component testing Condition: Used system with age and usage-related wear. Visual condition as per photos. The unit comes from industrial use. Scope of delivery: - NOVOTEST impulse test stand - Test cell / test chamber - Hydraulic power unit - Control and operator cabinet - PC / monitor / operator unit - Drawer cabinet with accessories - Technical documentation / folders - Scope of delivery as depicted Commercial sale – sale without warranty. Subject to changes and errors.

Condition: new, functionality: fully functional, Year of construction: 2026, container length: 6 ft, color: grey-black, overall weight: 2,500 kg, maximum load weight: 5,000 kg, loading space width: 4,876 mm, loading space length: 6,058 mm, loading space height: 285 mm, Equipment: cooling unit, Double Office Container / Living Container / Welfare Container Price: 13,500 Euros net Iodpozb D Rbefx Abvsau Description: OMEGA CONTAINERS has been active in the market since January 2017. We specialize in the complex production of office, welfare, living, and technical containers. We offer professional services ranging from planning and production to transport and installation. OMEGA containers are built on a solid steel frame, which allows the modules to be transported or moved with a crane without risk of damage. It is possible to transport the container multiple times. If required, we also build containers with structural calculations and specified documentation, as well as technical planning. The specific standard dimensions of our container: Length: 6058 mm Width: 4876 mm External height: 2850 mm Internal height: 2500 mm We also manufacture custom containers that are perfectly adapted to the customer's requirements. Steel construction: It consists of 3 mm thick open steel profiles with 5 mm thick sheet metal reinforcements. The surface is coated with an epoxy primer and painted with polyurethane paint. Color selection based on RAL color palettes. Roof: It is a steel structure with sandwich panels filled with 100 mm thick PUR foam polyurethane foam. The roof sealing consists of 1 mm thick galvanized sheet metal over the entire surface. Walls: Made of sandwich panel with 100 mm PUR foam polyurethane foam. The exterior facade is made of sheet metal in silver, white, or graphite. The interior facade is made of sheet metal in white. Flooring: Made of tightly welded steel profiles. The sealing consists of trapezoidal sheet metal t-14. Insulation made of 100 mm pressed wool. Floor 25 mm OSB. Finished with an industrial PVC lining with increased abrasion resistance + cover sheet. Fittings: - 1 piece - 900mm x 2000mm sheet metal door, in white or anthracite. - 3 pieces - Window 1200mm x 1200mm tilt-and-turn window - 3 pieces – External roller shutter Electrical installation: 2x electrical distribution boxes - residual current circuit breakers + fuses residual current + fuses 2x electrical connection 32A 5P 2x external plug 32A 5P 4x LED lamp (2x36W) 6x double socket 2x electric heater 2kW Additional options: - It is possible to equip the container with a toilet, a shower, a sink, including water connection, heating, etc. - Installation of several windows in various sizes. - Installation of glass doors - Installation of roller shutters. - Installation of air conditioning systems with room heating - Partitioning of containers into rooms - Connection of several containers to form a single unit. We cordially invite you to contact us!

Condition: new, Korn-KALI® 38+6 Potassium chloride with added magnesium salts MINERAL FERTILIZER K2O (MgO, SO3) 38 (6, 12) Declaration of nutrient content (m/m) • 38 % K2O water-soluble potassium oxide (= 31.5 % K) • 6 % MgO water-soluble magnesium oxide (= 3.6 % Mg) • 12 % SO3 water-soluble sulfur trioxide (= 4.8 % S) Particle size Granules. 95 % of the product passes through a sieve with a mesh size of 4.8 mm. Ingredients • Potassium chloride (KCl), CAS No. 7447-40-7 • Sodium chloride (NaCl), CAS No. 7647-14-5 • Magnesium sulfate monohydrate (MgSO4 • H2O), CAS No. 14168-73-1 All ingredients are "primary raw materials and mixtures" (CMC 1). Iodpfxszb Rlfe Abvsau Instructions and dosages: For professional use only! Crop Yield Amount • Cereals average yield 200-350 kg/ha • Cereals high yield 250-450 kg/ha • Rapeseed average yield 230-600 kg/ha • Rapeseed high yield 150-700 kg/ha • Sugar beets average yield 350-1000 kg/ha • Sugar beets high yield 450-1200 kg/ha • General recommendations are based on an average level of nutrient availability in the soil. • Recommended for soil application. • Suitable for crops that tolerate chlorides. Recommended storage conditions • Protect fertilizer stock with a tarpaulin. • Store in a cool (< 30 °C) and dry place! Safety and environmental information • To avoid hazards to human health and the environment, follow the instructions for the recommended use of this fertilizer product. Comply with local legal requirements! The stated price applies to a quantity of 1000 kg EXW, and transport costs are determined individually. Minimum purchase quantity: 24,000 kg.

Condition: new, power: 132 kW (179.47 HP), Year of construction: 2026, GNR 944 Mobile Crushing Plant with Cone Crusher Mobile river stone crushing and screening system with cone crusher. Our mobile cone crushers break hard and abrasive mineral materials with a capacity of 150 tons per hour. Please contact us for this plant that can break even very hard mineral materials. Ijdjwfru Depfx Abveau

Condition: new, power: 250 kW (339.91 HP), fuel type: electric, color: dark red, maximum load weight: 70,000 kg, tire condition: 99 %, axle configuration: > 3 axles, brakes: other, Year of construction: 2026, machine/vehicle number: GNR 944, GENERAL MAKINA 944 is our high-production mobile crushing and screening plant for hard and abrasive stones at mines and minerals. It can crush hard stones and minerals such as basalt, granite, iron ore, chrome, and quartz in a mobile way at any desired location.Our facility, which takes its power from its jaw and cone crushers, derives its performance from Vibro-feeder bunker, conveyor belts (bypass, return, stock), and 3-decks vibrating screen. The improved 4-axle new mobile chassis body (facility platform) has transport and strength characteristics at international standards. General 944 Mobile Crushing Plant production capacity is between 120 and 180 t / h. For more detail please contact us. Iaedpfjy Daziox Abvou

Condition: excellent (used), Year of construction: 2008, The new powerful dry-running pumps: The ADH series is specially designed for solar developed for the demanding processes of the semiconductor and LED markets, With a suction capacity of 600-4500 m3/h. Isdpsikq Tyefx Abvsau Semiconductors: High H2 pumping rate The performance of the ADH series brings the following advantages to the process: -ADL process performance: high pumping efficiency of light gases enables faster chamber emptying between process steps - Epitaxy and EUV: high pumping speed and high flow rate Tolerance meets the most demanding process specifications Adixen AD30K dry pump, high vacuum, AD 30 KL Manufacturer: Alcatel Adixen Type: AD30K.H Year of manufacture: 2008 Adixen AD100K.H Manufacturer: Alcatel Adixen Type: AD100K.H Year of manufacture: 2008 Vacuum pump: Manufacturer: AERZEN Type: GM 2000 CM-C Speed: 6000 rpm Voltage: 200-460 V Frequency (mineral oil/PFPE oil): 100 c/s Maximum suction capacity: 4035 m3/h Maximum speed: 5920 rpm Engine power S 1 / S 6: 9/5.6 kW Year of manufacture: 2008 Weight: 345 kg Dry pump: Manufacturer: Adixen Type: BF ADP122 Year of manufacture: 2008 Power 1.5 kW Maximum suction capacity: 95 m3/h Maximum continuous inlet pressure: 50 mbar Maximum exhaust pressure: 1200 mbar Cooling water: 60 l/h Speed ​​(pump): 3000-3600 rpm Operating temperature of the pump: from 5 °C to 40 °C Inlet flange: DN 50 ISO-KF Exhaust flange: DN 40

Condition: used, Year of construction: 2001, functionality: fully functional, type of input current: three-phase, filter area: 16.5 m², suction capacity: 2,400 m³/h, Equipment: type plate available, Dust extraction unit, Donaldson Torit brand, vacuum filter, dust collector for extracting metal, mineral, and hard fiber dust, and for effectively collecting process dust. Donaldson Torit Vibra Shake is a self-cleaning dust extraction unit for intermittent applications where high collection efficiency is important, e.g., recovery of precious metals. Two-stage filter cartridge for high-performance filtration of both coarse and fine dust. The filter screen captures coarse and fibrous particles. The vacuum fan is located behind the filter on the clean air side, minimizing the risk of explosion. Brand: Donaldson Torit Model: VS 1500 (Vibra Shake) Iaodpfxjy Sz Dne Abvou Fan power: 3 kW Capacity: 2400 m3/h Filtration area: 16.5 m2 Inlet diameter: 180 mm Stock number: 1140