Used Sound Wall for sale (7,206)

Condition: used, Year of construction: 2010, machine/vehicle number: 1000017741, inner dimension length: 1,000 mm, inner dimension width: 840 mm, inner dimension height: 815 mm, operating temperature: 1,700 °C, usable tank capacity: 685 l, No minimum price – guaranteed sale to the highest bidder! The machine was professionally dismantled and stored. All parts and connections are labeled for reassembly. An on-site inspection is possible at any time. TECHNICAL DETAILS Furnace chamber and usable space Usable batch space (W × H × L): 840 × 815 × 1,000 mm Total length of the graphite box: approx. 1,100 mm Usable volume: approx. 685 l Operating temperature: max. 1,700 °C Operating temperature under partial pressure: max. 1,500 °C Operating temperature under vacuum: max. 1,700 °C Temperature uniformity: ± 10 K Temperature fluctuation in the steady state: ± 5 K MACHINE DETAILS Process pressure range: 1 × 10⁻² < p < 1,040 mbar Final pressure in the empty, clean, and cold furnace: < 1 × 10⁻² mbar Leak rate: < 5 × 10⁻³ mbar·l/s Power supply: 3 × 400 V, 50 Hz Permissible voltage fluctuation: max. ± 5 % Installed heating power: max. approx. 190 kW Electrical power of the pump station: approx. 14 kW Cooling water flow rate: approx. 150 l/min Cooling water temperature: 20–30 °C Cooling water pressure: 2–4 bar Cooling water quality requirements: according to specification PW 800 943 ND Compressed air for valve operation: 4–5 bar Nitrogen inlet pressure: 5–7 bar Hydrogen inlet pressure: 5–7 bar EQUIPMENT Double-walled furnace chamber made of stainless steel with water cooling Internal graphite box for precise guidance of the process gases Post-cleaned graphite components Automatic control of the entire process Pump station Labeled lines and connections for easier recommissioning Note: Two internal graphite heating elements were damaged during dismantling and must be replaced. Ndsdsz I Tt Iepfx Akqjc

Condition: like new (used), Year of construction: 2025, operating hours: 91 h, functionality: fully functional, machine/vehicle number: SMG25/2-S2H-2x085-603/0,48, pressure: 3 bar, operating pressure: 5 bar, total width: 1,500 mm, total height: 1,700 mm, total length: 2,500 mm, type of input current: three-phase, overall weight: 500 kg, inner dimension width: 650 mm, inner dimension length: 450 mm, inner dimension height: 550 mm, input current: 1 A, input voltage: 400 V, space requirement width: 1,500 mm, construction width: 1,000 mm, space requirement length: 3,000 mm, space requirement height: 2,000 mm, Equipment: cabin, compressor, documentation/manual, lighting, MHG blasting system SMG 25 DUO hand blasting booth with double booth. We offer this like-new MHG SMG25/2-S2H-2x085-603/0,48 sandblasting system, manufactured in 2025. Like new: purchased new from MHG in September 2025 as the 2nd machine, and therefore unfortunately used very little. Currently 91 operating hours in 12 months. Identification number: SMG25/2-S2H-2x085-603/0,48 Order number: 2025-105286 Serial number: 11429/07/25 Machine color: RAL 7024 Supply voltage: 230/400 V Frequency: 50 Hz Phases: 3 phases + N + PE Rated current L1: 0.9 A Rated current L2: 0.8 A Rated current L3: 0.8 A Fuse: 3 × C 16 A Wiring diagram version: 1.2.5 DEU PLC program version: 1.2.6 DEU If you have any questions or need more information, please send us a message or call us. ----- MHG blasting system SMG 25 DUO hand blasting booth with double booth. Like new: purchased new from MHG in September 2025 as the 2nd machine, and therefore unfortunately used very little. Currently 91 operating hours in 12 months. Further details upon serious inquiry. TYPICAL APPLICATION AREAS Precision engineering Medical technology Nodpfsz Eq Epjx Akqedc Extremely small, precise components Laboratory applications Toolmaking WORK AREA 650 x 450 x 550 mm each (W x D x H) BLASTING CHAMBER Dust-tight, under-pressure chamber in a robust steel sheet construction WORK GLOVES Special rubber, abrasion-resistant, inner lining cotton, securely connected to the booth to prevent dust leakage DOORS Two side doors, dust-tight closing, double-walled, sound-absorbing foam filling, lockable, with electrical interlock for safety BLAST MEDIA RECOVERY Via a coordinated MHG recovery system OPERATION Separate for each work area, ON/OFF switch for extraction and lighting, pressure regulator, manometer and foot switch VIEWING WINDOWS Safety glass, 500 x 320 mm each, can be replaced without special tools BLASTING CHAMBER LIGHTING Wear-free, mounted externally, very good illumination by fluorescent tube, optional LED lighting unit MHG BLASTING GUNS High-performance blasting gun, MHG system, with optimal efficiency, operated via foot pedal, available with nozzles in different sizes and materials WORKPIECE BLOW-OFF NOZZLES For cleaning the blasted workpieces and the blasting chamber. ENERGY-SAVING FUNCTION - INTEGRATED IN ALL MHG BLASTING BOOTHS: Clearly arranged in the lamp housing: ON/OFF button for light ON/OFF button for extraction fan Both functions have separate energy-saving times (adjustable in the LOGO). The standard settings are 5 minutes for lighting and 10 minutes for extraction. If the blasting booth is not in use, the lighting will switch off after five minutes and the extraction will switch off automatically after ten minutes. Both functions are reactivated by simply pressing the foot pedal, without the blasting booth having to be switched on manually. When a booth door is opened, the lighting is automatically switched on and the energy-saving time starts again. Maintenance indicator light A "Maintenance" indicator light is located on the control panel. This flashes after 1000 operating hours and is reset by the service department. By adhering to the maintenance intervals, the blasting booth is always kept in an technically optimal condition. www.mhg-strahlanlagen.de/de/strahlanlagen/handstrahlkabinen/smg- 25-duo/

Condition: excellent (used), Year of construction: 2007, Striebig Panel Saw Compact 5220, Year of Manufacture 2007 Solid, self-supporting, firmly welded, and torsion-resistant saw frame Stable, durable saw beam steel construction Robust mounting of the motor carriage ensures high cutting precision Powerful, low-vibration 3.0 kW motor (S1) TRK dust extraction system Automatically adjusting aluminum grid with plastic supports Device for wall mounting Ball-bearing support rollers Split center support at optimal working height, with aluminum grids Integrated small parts support made of wood Supersilent sound insulation to reduce saw blade noise Electromagnetic motor brake Saw weight approx. 910 kg Cutting depth 60 mm Saw motor power 3.9 kW (5.3 hp) Saw blade diameter 250 mm Saw blade bore 30 mm *1 Emission sound pressure level at the workplace LpA 82 dB *2 Saw blade speed 5250 rpm Ndjdpfjz N Igaox Akqjc 2 dust extraction ports ø 100 mm Connection value 4.8 kW Mains connection 3 x 400 V / 50 Hz Cutting range: L: 4300; H vertical: 2200 mm, H horizontal: 2100 mm Equipment: - Compact 5220 - Freestanding support, complete Location: In stock, 54634 Bitburg - immediately available -

Condition: used, The Compact Series The new Wanner shredding mills in the C series (“C” stands for “compact,” “s” stands for “silent,” meaning noise-optimized) offer practical solutions for almost all challenges related to in-line recycling of sprues and defective parts in the production process. Thanks to their modular design, the shredding mills in the C series can be easily adapted to the specific application or the needs of the operation. Depending on the method of feeding the sprues, the disposal of the ground material, or the injection molding machine being used, the C series from Wanner offers optimal solutions that can be adapted to your specific operational processes through a variety of standard components. The optimized cutting geometry and low rotor speed guarantee high-quality ground material with a low dust content. Sound-insulated feed hoppers and the noise-optimized shredding chamber design contribute to a low noise level with regard to structure-borne noise and natural frequency. The large-sized gearbox ensures a long service life for the shredding mills and also allows for extremely compact dimensions. The shredding chamber can be opened very easily with just a few steps, which saves time and thus costs, for example, during cleaning due to a change of color or material. The advantages of the C series: easy adaptation to the specific application through a modular system compact design requires only a small footprint next to the injection molding machine robust, cast/steel housing mounted on swivel casters durable motor/gearbox unit for a long service life significantly reduced noise through angled-cut rotor and vibration-optimized shredding chamber design easy handling and simple cleaning, saving time and costs improved feeding behavior of bulky sprues and ground parts thanks to the optimal rotor geometry shredding chamber with hardened inserts for minimal wear with GF materials high-quality and low-dust ground material thanks to the optimized cutting geometry. The rotating disc in the side wall reduces friction and thus heating and damage to the ground material. blades can be easily re-sharpened without a special device sound-insulated and tamper-proof feed hoppers Technical data: Manufacturer: Wanner Type: C17.26sv Nsdezc Nydepfx Akqodc Shredding chamber opening: 170 x 260 mm² Rotor diameter: 170 mm Rotor blades: 12 Stator blades: 2 Throughput: 20-25 kg/h Screen size: 3-8 mm Voltage: 400 Volt/ 50 Hz Suction container: approx. 6 l Suitable for GF materials as standard Control: Contactor control with overcurrent protection switch electrically redundant design with self-monitoring safety relay according to EN 12012 5 m connection cable Weight: 155 kg Year of manufacture: Product video “Everything from a single source: We would be happy to offer you suitable bank financing for your project.” You can find more new and used items in our shop! International shipping costs on request!

Condition: used, Year of construction: 2023, Special price – Showroom machine Garbsen INDUSTRIAL AUTOMATIC EDGE BANDING MACHINE stefani md (the images of the machine are not binding with regard to the actual features specified below) KEY FEATURES EDGE BANDING OF SOLID WOOD UP TO 15 MM THICKNESS: SIMPLE AND FUNCTIONAL PROCESSING OF EDGES WITH LARGE DIMENSIONS "SGP" GLUE TANK: USE OF EVA AND POLYURETHANE GLUE FOR A PERFECT GLUE JOINT "STARTOUCH" CONTROL: A TOUCH IS ALL IT TAKES TO OPERATE THE MACHINE GENERAL FEATURES Automatic single-sided edge banding machine for applying edge banding with hot melt adhesive to the four sides of straight panels and for subsequent finishing. Machine frame and longitudinal supports made of cold-rolled steel in a box construction, manufactured in a single element, for high rigidity and vibration-free operation to accommodate the working units. Openings with slides for discharging any remaining chips to the floor. Upper pressure beam made of thick-walled steel construction and with columns made of cast iron, for a vibration-free structure where the working units are attached. Pressure rollers on the feed chain in a double row, made of rubber with a high coefficient of friction and with sliding on bearing rollers. Device to protect the pressure rollers from any remaining chips. Electronic adjustment of the upper pressure unit, depending on the panel thickness. Upper working units attached to the pressure beam or mechanically connected to ensure automatic adjustment when changing the panel thickness. Lower working units attached to the machine frame or to the longitudinal support, for a precise reference to the panel. All high-frequency motors are operated via frequency inverters. Protective cover for all units positioned after the gluing unit. Windows made of polycarbonate ensure a good view of the units during processing. Interior lighting of the cabinet. Protective cover with sound-absorbing material for lower noise emissions during processing. The spacer on the infeed guide allows the machine to be fed in the correct spacing. The spacing is automatically adjusted to the selected feed speed. Extraction nozzle arranged on the soundproof hood. Swivel control panel in an ergonomic position at the machine infeed. The electrical system complies with current regulations. Electrical components housed in a metal housing, attached to the machine frame and provided with doors for convenient access during any maintenance work. Panel feed The panel feed is carried out via a feed chain consisting of rubber sliding blocks with a high coefficient of friction, attached to a 1-1/4" industrial chain. The chain slides on 2 guides made of hardened and ground steel, a round guide and a flat guide, to guarantee a straight feed and protect against lateral displacement. Automatic lubrication of the chain. The amount of lubricating oil is optimized by the control system depending on the panels being processed. Support roller track externally and positioned along the entire length of the machine; consisting of an extendable opening system with sliding on linear bearings and plastic sliding rollers with steel pivot pins. "STARTOUCH" CONTROL Main features: 12" touchscreen color display Graphical representation of all processing units and their status (on/off) Njdpfozc Ilxox Akqjdc

Condition: good (used), Year of construction: 2010, Striebig Panel Saw Compact 5220, Year of Manufacture 2010 Robust, self-supporting, firmly welded, and torsion-resistant saw frame Stable, durable saw beam steel construction Robust bearing of the motor carriage ensures high cutting accuracy Powerful, low-vibration 3.9 kW motor (5.3 HP) TRK dust extraction system Automatically adjusting aluminum slat grid with plastic supports Device for wall mounting Ball-bearing support rollers Split center support at optimal working height, with aluminum grid Integrated small parts support made of wood Supersilent sound insulation to reduce saw blade noise Electromagnetic motor brake Saw weight approx. 910 kg Cutting depth 60 mm Ndsdpfx Akezhx A Reqec Saw motor power 3.9 kW (5.3 HP) Saw blade diameter 250 mm Saw blade bore 30 mm *1 Emission sound pressure level at the workplace LpA 82 dB *2 Saw blade speed 5250 rpm 2 dust extraction ports ø 100 mm Connection value 4.8 kW Mains connection 3 x 400 V / 50 Hz Cutting range: L: 4600; Hvertical: 2200 mm, Hhorizontal: 2100 mm Equipment: - Compact 5220 - Strip fence - Mechanically braked support rollers - Freestanding support complete Location: Available from stock in 54634 Bitburg - immediately available -

Condition: good (used), Year of construction: 2008, Striebig Panel Saw Compact 5220, Year of Manufacture: 12/2008 Solid, self-supporting, firmly welded saw frame with high torsional rigidity Stable, durable saw beam steel construction Robust mounting of the motor carriage ensures high cutting accuracy Powerful, low-vibration 3.0 kW motor (S1) TRK dust extraction system Automatically adjusting aluminum slat grid with plastic supports Device for wall mounting Ball-bearing support rollers Split center support at optimal working height, with aluminum grid Integrated small parts support made of wood Supersilent sound insulation to reduce saw blade noise Electromagnetic motor brake Saw weight approx. 910 kg Ndodpfx Akszp Nt Ajqsc Cutting depth 60 mm Saw motor power 3.9 kW (5.3 HP) Saw blade diameter 250 mm Saw blade bore 30 mm *1 Emission sound pressure level at the workplace LpA 82 dB *2 Saw blade speed 5250 rpm 2 dust extraction ports ø 100 mm Connection value 4.8 kW Mains connection 3 x 400 V / 50 Hz Cutting range: L: 4600; H vertical: 2200 mm, H horizontal: 2100 mm Equipment: - Compact 5220 - Freestanding support, complete Location: Available from warehouse 54634 Bitburg - immediately available -

Condition: used, Weiss climate testing chamber with seat pulsator Manufacturer: Weiss Type: SD 1400/+20 DU Test chamber: Material: Stainless steel Dimensions Height approx. 800 mm Width approx. 2000 mm Depth approx. 900 mm Volume: 1440 liters Outer housing Material: Double-coated Zincor sheet Dimensions Height approx. 2000 mm Width approx. 2200 mm Depth approx. 2000 mm HxWxD 2000 x 2200 x 2000 mm Paint: light gray (RAL 9002) Door, double-leaf: hinged on the left and right Equipment: Passage through the floor and ceiling: 2 pieces each, nominal diameter 100 mm, for installing the pulsation table Passage in the side walls: 1 piece each, left, right, 100 mm Refrigeration unit: air-cooled Control: Digital measuring and control system DMR Basic control panel: integrated in the main switch panel Interface: RS 232 C, for connection to a PC Software: Operating software for MS-Windows Performance data: Temperature range without climate control: +20...+100 °C Temperature stability without climate control: +0.2 … ±0.5 K (time-dependent) depending on the range, in the stable state Temperature range with climate control: 20...+95 °C Temperature stability with climate control: +0.2 … +0.5 K (time-dependent) depending on the range, in the stable state Dew point range: 20...+94 °C Humidity range: 10...98 % RH Nodpjxbgrgefx Akqedc Humidity stability: +3 ... +5 % RH, depending on the range, in the stable state Temperature change rate measured in the outlet without test specimen and without load - Cooling: 0.5 K/min on average, between +100 and +20 °C - Heating: 0.5 K/min on average, between +20 and +100 °C The performance data refer to an ambient temperature of max. +25 °C and the specified rated voltage. For proper operation of the system, the ambient temperature must be between +10 and +35 °C. Connections / Other Protection class: IP 32 for the control cabinet Sound pressure level during free-field measurement at a distance of 1 m in front of the device: 60 dB (A) Humidification water: fully demineralized, conductivity max. 20 μS/cm, pH value 6 - 7, automatic replenishment Condensate drain: backpressure-free, 3/4" hose connection Mains connection: 400 V; 3 PH+N PE; 50 Hz Connection value: max. 10 kVA Weight: approx. 1160 kg Seat testing device with steel structure for mounting and securing to the climate testing chamber, including: • 2 pneumatic weight lifting devices (150 mm stroke) for test specimen changeover, 12 weights each with 5 kg • 1 base frame in normal steel welded construction for fastening to the underside of the climate testing chamber. This frame is equipped with removable sheets on all sides and has 2 folding doors for adjusting the eccentricity. These doors have safety switches. • 2 eccentric disks with bearing and tachometer, 2 connecting rods, 2 ball guides • 2 mounting tables, perforated, 20 mm grid, 650 x 650 mm, for connecting the test specimens, made of aluminum, thickness min. 10 mm • 2 mounting plates, perforated, 20 mm grid, 200 x 200 mm, for connecting the buttock simulation • 2 load rods, 600 mm long, made of stainless steel (The connection to the test specimen is not included in our price, but can be offered at a later date after a precise definition.) • 2 three-phase motors, 2 belt drives with tensioning devices • 1 pneumatic control with 2 hand valves, a filter-regulator unit and a shut-off valve, 1 electrical control cabinet with 2 SEW frequency inverters, hand switch, emergency stop button, 2 push buttons, 2 release buttons, 2 speed indicators, 2 potentio

Condition: used, Bystronic Type: ERMM180 Thermoplastic Applicator Application Area The thermoplastic applicator applies a thermoplastic material to rectangular glass panes within a production line for solar modules. The material forms a seal to a second glass pane, which is applied in a later process step. The panes are fed in, the material is applied, and the panes are removed on horizontally running belts/conveyors. The thermoplastic applicator is a highly advanced machine that must meet many requirements with great precision. For this reason, you should only process raw materials (glass, sealant) that meet the specifications on the following pages. This helps to achieve a high-quality and safe production. Performance and Connection Values Maximum transport speed: 18 m/min Height of the glass running surface: 1100 mm Height of the applied sealant bead: 0.5 to 1.2 mm Maximum width of the applied sealant bead: 12.0 mm Required constant inlet pressure, pneumatics: 6.5 to 8.0 bar Operating pressure, pneumatics: 6.0 bar Compressed air consumption, normal operation: 10 normal liters/min Compressed air consumption during drum change: 500 normal liters/min Average energy consumption per hour: 10 kWh Operating temperature of the sealant: 110°C to 130°C Ambient Conditions and Emissions Minimum ambient temperature: +15°C Maximum ambient temperature: +35°C Maximum relative humidity: 75% Sound pressure level: less than 70 dB (A) Requirements for the drums for the sealant Design: Material-lid container D18 according to DIN 6644 – with foot (F1) and smooth outer surface (body design, smooth). Capacity: 216 liters Inner diameter: 571.5 mm Height: 874 mm Minimum wall thickness: 1.25 mm Processable glass panes Glass types Glass panes with a smooth surface (float glass) can be processed. Nedszdyh Hspfx Akqjdc Dimensions and weights Smallest dimensions Largest dimensions Geometry 1198 mm 1200 mm Length LS 498 mm 600 mm Width BS 1.8* mm 5.0* mm Thickness DS Thermoplastic materials based on poly-isobutylene (butyl) can be processed. The material must be flowable in the range of approximately 110°C to 130°C and have a defined viscosity curve. Only use materials that have proven themselves in practice and have been approved by the manufacturers of these materials and by Bystronic for your intended use. For detailed product descriptions and information on the handling, storage, and disposal of the material used, please refer to the information sheets and safety data sheets, which the manufacturers of the materials will gladly provide. Dimensions of portal robot with glass conveyor Height x Width x Depth: 2800 x 1890 x 2735 mm Weight of the portal robot: 850 kg Weight of the glass conveyor: 1400 kg Dimensions of drum pumps Height x Width x Depth: 3320 x 1060 x 1200 mm Weight (without drum): 850 kg Weight (with drum): 1100 kg Height H at drum pump FP1: 4400 mm Height H at drum pump FP2: 4000 mm Dimensions of control cabinet Height x Width x Depth: 2200 x 1800 x 600 mm Weight: 450 kg The applicator was used with butyl material. Condition: used From a test laboratory, in new condition, only a few operating hours for testing! Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have over the phone.

Condition: new, functionality: fully functional, Year of construction: 2023, overall weight: 39 kg, extraction blower, wall-mounted fan high-performance fan, axial fan Industrial axial fan 800mm diameter ZIEHL-ABEGG fn80-sdi.6n.v7 NEW! Sold in a box of several pieces manufacturer: ZIEHLL-ABEGG type: FN080-SDI.6N.V7 Axial fan with sickle-shaped aluminum blades air flow: 10000-24000m3/h nominal air flow: 15800m3/h at 140pa air pressure motor power: 1.15kw/0.53kw Nominal values 3. phase~400V D/Y 50Hz 1.55/0.95kW 3.3/1.7A rpm:850/650/min Protection type:IP54 Ndsdpfxew U T E Is Akqsc sound level:70 dB COSY 0.69 max temperature range:80°C Motor protection: thermal contact Protective grid type: mesh grid Dimensions (w x h x d) mm: 861 x 861 x 273

Condition: used, mileage: 90,616 km, power: 177 kW (240.65 HP), first registration: 03/1998, fuel type: diesel, overall weight: 15,000 kg, axle configuration: 2 axles, color: red, gearing type: mechanical, total width: 2,400 mm, total height: 3,170 mm, Year of construction: 1998, Equipment: ABS, compressor, Mercedes-Benz 1524 with METZ DLK 23-12 PLC II aerial ladder – Registered: 05.03.1998 Mileage: 90,616 km Operating hours: 3,626 hours Base vehicle equipment: * Suspension type: leaf spring rear axle * Wheelbase: 4250 mm * Permissible gross vehicle weight: 15 t * 7-speed manual transmission * Fuel tank: 127 l, located under the platform at the rear * Differential lock in rear axle * Stiffer rear springs and shock absorbers * Front spring: torsion bar, reinforced stabilizer and shock absorbers * Co-driver's double bench seat * Exhaust pipe for fire department, positioned in front of the front axle * Engine brake * Anti-lock braking system (ABS) * Traction control system (ASR) * Fog lights * Hour meter * Headrest for driver * 2 headrests for co-driver * Cab rear wall with 2 windows * Electric window lifter on the right * Heated and electrically adjustable rear-view mirror with wide-angle mirror * Ramp mirror on the right * Rotating beacon, blue light, and siren * Front flashing blue light Aerial ladder equipment: Njdpjxa Sbwofx Akqodc * Metz aerial ladder DLK 23-12 PLC III with rescue basket (rescue height approx. 30.75m) Max. outreach angle: 75 degrees, Max. basket load capacity: 270 kg, Nominal rescue height: 23m, Nominal outreach: 12m, Outrigger system: horizontal-vertical, Variable outrigger width between 2,400mm and 4,500mm * Folding rescue basket for 3 people * 2 LED spotlights 24V at the front of the rescue basket * Load eye at the top of the lower ladder, on the reinforced ladder support, for lifting, lowering and pivoting loads * Mounting bracket for portable generator 5kVA on the turntable * 2 halogen spotlights 24V / 70W at the head of the lower ladder with Teleflex control from the main control station * 400V power supply, protected in the ladder support, to the top of the upper ladder including socket and power supply with plug from the generator on the turntable * Bridge cable from the head of the upper ladder to the rescue basket with 1 socket 400V and 2 sockets 230V in the rescue basket * Fixed water line in the lower ladder * Adjustable spray nozzle, mountable in the rescue basket * Storage for adjustable spray nozzle * METZ stretcher holder SLK 111 including storage on the platform * Box for storing the stretcher in the platform * Siren with 4 sound cups instead of BOSCH high-tone horn * Fixed charger 230V / 24V * Service booklet available, all maintenance performed annually ----Ready-to-drive vehicle from first owner, ladder system only works sporadically - defects present! Non-smoking vehicle! Your contact person for this vehicle: ---- Daniel Seidler Tel: Mobile: also Whatsapp Email: Subject to changes, prior sale and errors!

Condition: used, Year of construction: 2016, Industrial automatic edge banding machine SOLUTION XD KEY FEATURES "E-TOUCH" CONTROL WITH AUTOMATIC PROGRAMMING: A SINGLE "TOUCH" IS ALL IT TAKES TO OPERATE THE MACHINE STANDARD PRESSURE DEVICE WITH DRIVE BELT FOR OPTIMAL PANEL GUIDANCE EDGE BANDING OF ROLL MATERIAL, STRIP EDGES AND SOLID WOOD EDGES GENERAL FEATURES Single-sided edge banding machine in left-hand version for edge banding of roll material and strip edges with all conventional hot melt adhesives. The base frame consists of a stable steel welded frame with higher rigidity, which provides optimal support for the installation of the processing units. The upper pressure beam consists of a thick-walled steel profile and a double trapezoidal drive belt, which is automatically positioned according to the panel thickness. Height adjustment with display on the upper pressure beam and on the operator panel. Manual workpiece feeding system with a large-sized work area and increased support surface facilitates the feeding of large workpieces. Adjustable infeed fence for two positions with automatic selection for processing with or without a pre-milling unit. Upper working units are attached to the pressure beam and mechanically connected to ensure automatic adjustment when changing panel thickness. Lower working units are attached to the machine frame or to the longitudinal support for precise referencing to the panel. All high-frequency motors are operated via frequency inverters. Each unit is equipped with its own inverter for optimal flexibility and improved machine production times. Protective hood for all units positioned after the glue application unit. Polycarbonate windows ensure a good view of the units during processing. Interior lighting of the hood. Protective hood with sound-absorbing material for lower noise emissions during operation. Spacer on the infeed fence allows the machine to be fed with the correct spacing. The spacing is automatically adjusted to the selected feed rate. Dust extraction port arranged on the pivoting control panel, positioned in the infeed area, is adjustable for ergonomic operation. The electrical system complies with current regulations. Electrical components are housed in a metal housing, attached to the machine frame and equipped with doors for easy access in case of maintenance. Standard voltage is 400 V EU 50 Hz (with neutral conductor). Material feed is via a feed chain with 80 mm wide chain plates made of rubberized nylon, for optimal guidance and high load capacity. The chain slides on 2 guides made of hardened and ground steel, one round and one flat guide, to guarantee straight feed and to protect against lateral displacement. Automatic chain lubrication. The amount of lubricating oil is optimized by the control system depending on the panels being processed. External support roller track positioned along the entire length of the machine; consisting of an extendable opening system up to 650 mm (for panels with a maximum width of 1200 mm). E-TOUCH PC control system for quick and easy execution of the main functions of the machine. Includes: – Processing of programs in Just in Time mode – Possibility of management via bills of materials – Possibility of management by Nedpjxy Tm Iefx Akqjdc

Condition: used, functionality: fully functional, machine/vehicle number: WDB4371251W199327, mileage: 318,533 km, power: 177 kW (240.65 HP), first registration: 07/2002, fuel type: diesel, empty load weight: 7,300 kg, overall weight: 7,500 kg, tire size: 395/85 R 20, axle configuration: 4x4, brakes: engine braking, color: white, gearing type: mechanical, number of seats: 3, total length: 7,170 mm, total width: 2,410 mm, total height: 3,500 mm, permissible axle load (axle 1): 4,400 kg, permissible axle load (axle 2): 4,400 kg, Year of construction: 2001, operating hours: 4,765 h, Equipment: ABS, parking air conditioner, Unimog U1550L Expedition Vehicle First registration: 07/04/2002 Mileage: ≥ 318,000 km Operating hours: ≥ 4,700 h Total weight: 7,500-8,500 kg depending on load Engine: 176kW / 240 hp, Euro 2 Tires: 395/85 R 20 - Michelin Asking price: €139,800 Special equipment Unimog: A27 Double sealing of wheel hub, for use in muddy conditions A30 Tire pressure control system A31 Wheel-side, wheelbase-dependent parts for tire control B02 ABS Nedpfx Aoz S Ni Iskqjdc B28 Mechanical quick-release device for spring storage cylinders C22 STABILIZER SEAL FRONT AND REAR C34 Anti-slip coating on bumpers D65 Mounting parts for external superstructures E35 Circuit breaker instead of fuse F06 Higher cab roof (by 120mm) F44 ADDITIONAL VENTILATION F50 SOUND AND HEAT INSULATION FOR CAB G22 Auxiliary gearbox with off-road gear G50 Transmission oil cooler G73 SHIFTING DAMPER (SHIFT LEVER - TRANSMISSION) H02 Single-circuit hydraulic system H11 HYDRAULIC SYSTEM 1-CELL H71 HYDR. PLUG-IN CONNECTION FRONT 2-WAY, CELL 1 J24 Tachograph, 2 drivers, outside EU J29 Speed-dependent engine speed compensation (measurement result / warning sign) L02 Outline lights to the front, white L18 Fog lights, halogen, suitable for wading L25 Rear fog light L30 Stone guard grille for headlights L30 Headlight stone guard L35 Headlight beam adjustment L41 ADDITIONAL TURN SIGNALS L71 Side marker lights with integrated reflectors M02 EURO II ENGINE M03 Increased engine power M31 AIR COMPRESSOR WITH HIGHER OUTPUT M53 Fuel preheating M78 Engine number stamping M86 PULLEY AND VIBRATION DAMPER WITH COMBINATION RING M91 ELIMINATION OF START PILOT R27 Disc wheels 11x20 super S21 Three-point automatic safety belts S26 Windshield electrically heated, laminated glass S26 Electrically heated windshield, laminated glass S39 Power windows (left and right) S46 2 Outside rearview mirrors, heated, electrically adjustable S50 First-aid kit S82 Wide-angle mirror S83 Ramp mirror X18 Increased load capacity level UNICAT Expedition Mobile Superstructure: - Pneumatically sprung Recaro seats, adjustable, heated and ventilated - Robust GRP box body, wall thickness approx. 60–100 mm, waterproof and dustproof; designed for temperatures from -40 °C to +40 °C - Four-chamber fuel tank system with a total of 560 liters of diesel - Solar system on the roof and extensive on-board electrical system with a central control panel - 310 l fresh water tank, 80 l waste water tank, 22 l hot water boiler via heat exchanger and drinking water filter system - Kitchen with refrigerator, freezer, sink, hot and cold water, three-burner propane stove, oven and storage compartments - Sleeping area with a double bed, cabinets, mirror, reading light and storage space - Bench seat, can be converted into an additional sleeping space for a third person - Bathroom with porcelain toilet and flushing, washbasin, mirror cabinet and shower - Outside shower and outside water connection - Awning - Rear bicycle carrier, roof rack with spare wheel - Additional front headlights with protective grille - Winch at the front and rear - Ball hitch K50 Offer subject to change. Errors, changes and prior sale are reserved. All information without guarantee. Our general terms and conditions apply. Location: Peter Meineke GmbH Becklinger Straße 17 29683 Fallingbostel Viewings and/or test drives only by prior appointment. Please coordinate by telephone before arriving, as the vehicle/device may not be at the specified location. Contact: Ewgeni Schneider Mobile: +49 (0) 173 / 9903073

Condition: used, Vötsch Type: VLM 3068/S Vötsch Temperature Test Chamber VLM 3068/S, Air-Cooled (Top-loading test chambers for construction materials) Control Panel The control panel is mounted on a console on the temperature test chamber. All control and operating commands can be activated by simply touching the function symbols. The operating manual for the control panel is included. Main Switch The main switch is located at the front of the temperature test chamber. Air Handling Unit The air handling unit is located in the test chamber and contains the components necessary for temperature control. In the air handling unit, the air is conditioned (cooled/heated) and circulated through the test chamber by the test chamber fan. The air is drawn in at the center of the side wall and re-enters the test chamber via the air deflectors on the long sides. Feedthroughs The temperature test chamber can optionally be equipped with feedthroughs. These allow cables and testing equipment to be placed in the test chamber. Feedthrough at the front 2 x 82 mm diameter, at the rear 1 x 85 mm diameter. Internal Dimensions: Width 2000 mm, Depth 570 mm, Height 600 mm External Dimensions: Width 3000 mm, Depth 870 mm, Height 1060 mm Technical Data: Data for Mechanical Load: Max. load with test specimen Test chamber floor (evenly distributed over the area) 600 kg Point load 50 kg Data for Temperature Tests: Temperature range -30 °C to +125 °C Temperature deviation over time in the center of the useful space ±1 K Temperature change rate Heating approx. 1 K/min Cooling approx. 2 K/min Data for Operation: Rated voltage 3/N / PE AC 400 V ±10% 50 Hz Rated power 3 kW Rated current 9 A Fuse on customer side 16A slow-blow Temperature Test Chamber VLM 3068/S Test chamber volume approx. 680 l Weight approx. 700 kg Refrigerant: R-404A Noise measurement Sound pressure level approx. 68 dB(A) Condition: used Scope of delivery: (See picture) Ndedpfx Akjzgbmieqjc (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: as good as new (ex-display), functionality: fully functional, power: 5.52 kW (7.51 HP), input voltage: 400 V, input frequency: 50 Hz, saw blade diameter: 300 mm, total length: 6,689 mm, total width: 1,766 mm, total height: 3,055 mm, cutting length (max.): 5,300 mm, cutting depth: 80 mm, extraction nozzle diameter: 140 mm, Further technical data Vertical cutting height: 2,150 mm / 2,150 mm (with lowering function) Horizontal cutting height: 2,100 mm Width: 1,766 mm (free-standing) / 1,383 mm (wall-mounted) Cutting length: 5,300 mm / 3,000 mm / 5,000 mm (with lowering function) Saw frame Self-supporting, torsion-resistant, welded frame with latticework reinforcement on 4 solid machine feet Automatically deflecting timber support wall TRK1 with integrated small parts timber shelf Panel lowering device (PAV) with 2 panel lowering units for board materials up to max. 160 kg (80 kg per unit) Length stop profile above central support up to zero cut position Continuous length stop profile above roller support with flip stop Precise 17-fold roller support, pneumatically braked Swivelling central support along the entire length, support grid made of aluminum with plastic pads Unit for wall mounting Aluminum small parts support (1 pair), can be used individually Saw beam & saw unit Stable, durable saw beam with double locking Robustly mounted motor carriage for high cutting precision Pneumatic clamping of the motor carriage Powerful, high-torque saw motor 5.5 kW (7.5 HP) Integrated, high-performance TRK dust extraction system for external extraction unit Supersilent sound insulation Electromagnetic motor brake Paper holder Control Clear push-button control for easy operation Positioning of the panel lowering device via two-hand control User guidance via status LED indicators on panel lowering units Operating hours counter Dimension adjustment Programmable cam switch for recurring dimensions Laser-guided display of horizontal cuts Digital measurement system DMS-Y, including motorized fine adjustment Digital measurement system DMS-X, including manual fine adjustment, installation selectable above central or roller support Optional equipment 006 Striebig free-standing base support Nodpfx Akjxazapjqedc 103 Digital measurement system DMS, X-axis 104 Digital measurement system DMS, Y-axis 105 Additional digital measurement system DMS, X-axis 200 Pro Lock Easy-Fix tool clamping system at the saw blade 201 Scoring saw unit VSA 300 Additional panel lowering unit 401 Complete aluminum small parts support Including delivery and installation in postal code areas 71, 72, 73, 77, 78, 79, 86, 87, 88, 89

Condition: new, Viessmann Tecto RF WMC3 1450 Refrigeration Unit The Viessmann Tecto RF WMC3 1450 (also known under the series designation TectoRefrigo) is a state-of-the-art, plug-and-play, piggyback refrigeration unit for wall mounting in cold storage rooms for standard cooling applications. Ndsdpfx Aj Aa Rlrskqoc Technical Data • Manufacturer: Viessmann Refrigeration Solutions • Model Designation: Tecto RF WMC3 1450 (Size 2) • Equipment Type: Plug-and-play piggyback refrigeration unit (monoblock) for wall mounting • Integrated Bluetooth connectivity (for control via app and data tracking) • Automatic leakage detection • Pre-installed connection cables: 2.5 m for door contact switch and 5 m Modbus-RTU cable (for building automation system / BMS). • Application area: Standard cooling • Housing surface: Powder-coated, similar to RAL 9003 (signal white) • Cooling capacity at L0L32 (0 °C chamber / 32 °C ambient): 1450 watts • Cooling capacity at L0L43 (0 °C chamber / 43 °C ambient): 1270 watts • Control range for cold storage room: -5 °C to +10 °C • For cold storage room volume: Up to approx. 11.1 m³ to 15 m³ (depending on the selected insulation, goods, and set temperature) • Airflow (evaporator): 1000 m³/h • Permissible ambient temperature: +5 °C to +43 °C (indoor operation only) • Refrigerant: R290 (propane) – an environmentally friendly, natural refrigerant with a very low global warming potential (GWP 3) • Refrigerant charge: < 150 g • Global Warming Potential (GWP): 3 • CO₂ equivalent: < 0.45 t • Defrosting: Automatic hot gas defrosting with demand-controlled cycle control • Condensate: Automatic, integrated condensate evaporation • Maximum permissible wall thickness: 150 mm (for the mounting cutout) • Power connection: 230 V / 50 Hz (AC via CEE plug, blue, power consumption approx. 990 W) • Power consumption (nominal current): 5.4 A • Sound pressure level: 32.8 dB • Dimensions: 828 mm x 671 mm x 976 mm (H x W x D) • Weight: 64 kg (net) Dimensions for the wall cutout • Width of the cutout: 575 mm • Height of the cutout: 395 mm Key features • Piggyback design: The monoblock unit is simply hung into the corresponding cutout in the cold storage room wall (“piggyback”). The maximum wall thickness may be 150 mm. • Hot gas defrosting: The unit has an automatic, demand-controlled hot gas defrosting system with integrated condensate evaporation, so that a separate drain is usually not necessary. • Smart electronics: Equipped with modern control, Bluetooth connectivity (for app control and data tracking), and automatic leakage detection. • Components: Thermostatic expansion valve, pressure sensors, and efficient, internally finned heat exchangers. Important application notes • Ambient temperature: The device is designed exclusively for operation in closed rooms with an ambient temperature of +5 °C to +43 °C. It does not have a winter control system and is not weatherproof (no outdoor installation). • Accessories for Viessmann cells: If the WMC3 unit is mounted on a classic Viessmann cold storage room, a special adapter cable and a converter box are usually required to connect the door contact switch and the power supply correctly. “Everything from one source: We would be happy to offer you suitable bank financing for your project.” More articles – new and used – can be found in our shop! International shipping costs on request!

Condition: new, Year of construction: 2026, functionality: fully functional, warranty duration: 12 months, workpiece weight (max.): 500 kg, temperature: 250 °C, heating capacity: 105 kW (142.76 HP), air demand: 7,000 m³/h, workpiece height (max.): 1,600 mm, workpiece length (max.): 3,000 mm, Equipment: lighting, Compact powder coating system (complete system) – booth, curing oven, conveying system & Gema technology Complete system for manual powder coating of parts up to 3,000 mm in length and 500 kg payload per carrier. First-class brand-name components (Gema, Siemens, Schneider Electric, Donaldson, Riello), including installation, commissioning and operator training. Overview & Concept For sale is a brand-new, manual powder coating complete system for workpieces up to 3.0 m in length. The system combines an efficient extraction coating booth, a powerful gas curing oven, and a flexible rail conveying system including steel structure (individual design/planning of a powder coating system possible upon request!). 1. Powder coating booth (double-sided manual coating) - External dimensions (L x W x H): 3,400 x 1,100 x 2,150 [mm] - Workpiece opening dimensions: 500 x 1,600 [mm] - Extraction & filter: 2x radial fans at 4,500 m³/h (ATEX version, 3 kW each); 2 filter units with a total of 6 antistatic Teflon filters (Donaldson, 325 x 660 [mm]) - Cleaning: Automatic/manual compressed air pulse cleaning (6 valves) - Safety/equipment: ATEX-compliant internal lighting, sound insulation in the fan area, control via Siemens/Schneider wall control cabinet Electrostatic powder coating technology (Gema) (other manufacturers can also be supplied upon request) - 2x hand guns: Gema OptiSelect Pro with PowerBoost® technology, ATEX-certified - 2x control units: Gema OptiStar 4.0 CG20 with DVC and PCC precision current control, 250 memory programs, app connectivity - 2x injectors: Gema OptiFlow IG07 with quick-release & non-stick cartridge Convection curing oven (chamber oven with double door) - Internal dimensions (L x W x H): 3,500 x 2,000 x 2,300 [mm] - Max. temperature / operating temperature: up to 250°C / 180 - 200°C - Heating: Indirect thermo block with Riello/Ecoflam burner (approx. 105 kW (90,000 kcal/h)) - Fuel: Natural gas or liquefied gas (LPG) (other energy supply e.g. electricity possible upon request) - Recirculation: 2 x 3,500 m³/h recirculation fans (plus automatic fan exhaust fan) - Insulation: 150mm rock wool insulation Manual conveying system including steel structure Load capacity: Max. 500 kg per carrier Equipment: 5 oven rails, 15 carriers (3m each), 3 transverse transfer trolleys Running trolleys: Equipped with high-temperature resistant bearings Scope of supply & services / Commercial points Included in the price: Nodpfx Ajzu Imrokqodc - Booth with extraction & filter unit - 2x Gema powder coating units - Curing oven including thermo block & burner - Conveying system including steel structure & trolleys - Installation, commissioning & operator training on site

Condition: used, Year of construction: 2015, Wall line, manufactured to produce walls for modular manufacturing. Used by a Swedish producer between 2015 and 2021. NOTE: Sold in its current condition. Station lengths: 7000 mm Station width: 2700 mm Station nr1: Framing station CAD/CAM (includes two nail tools) Station nr2: Working table Station nr3: Semi automatic nailing bridge (includes two nail tools) Station nr4: Working table - Upraiser table Station nr5: Multifunction portal CAD/CAM (includes four screw tools and milling unit) Station nr6: Working station - Receiver table - Moveable sideways Station nr7: Working station - Angle transmission Station nr8: Working station - Upraiser table Station nr9: Working station - Angle transmission Ndedpfx Ajxv Arxokqjc Station nr10: Working station - Upraiser table

Condition: good (used), Year of construction: 1970, Column jib crane, overhead crane, workstation crane -Manufacturer: Demag, wall-mounted jib crane, lifting capacity 1000 kg -Projection: 5070 mm -Swivel range: 270° -Chain hoist: DEMAG type PK5NF -Main stroke: 5.0 m/min Njdpfx Ae Adzazskqedc -Fine stroke: 1.25 m/min -Hook travel: 4300 mm -Transport dimensions: 5300/1310/H400 mm -Weight: 316 kg

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Electrical Data Charging voltage: 80 V Charging current: 280 A Charger type: Modular HF charger General Data Manufacturer: Hawker Model: Life SeediQ Year of manufacture: 2019 Application: Forklifts / Electric forklifts MACHINE DETAILS Dimensions Length: 600 mm Width: 600 mm Height: 800 mm Weight Net weight: 80 kg Ndedpsz R Rizsfx Akqsc EQUIPMENT Battery connector Wall connector All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: Side loading up to 6 tons with a large forklift on site is possible. Loading is done at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons and up to a width of 230 cm. Collection is only possible after receipt of the payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. If the item is not collected on time, a storage fee of €20 per machine and day will be charged. Outstanding storage fees must be paid in full before collection. Lot number: 3758

Condition: new, mileage: 500 km, power: 265 kW (360.30 HP), overall weight: 18,000 kg, fuel type: diesel, color: orange, axle configuration: 2 axles, gearing type: automatic, loading space width: 2,420 mm, loading space length: 4,800 mm, loading space height: 600 mm, Equipment: ABS, air conditioning, all wheel drive, electronic stability program (ESP), parking heater, Municipal new vehicle, MAN TGS 18.360 BL 4x4 all-wheel drive tipper with Meiller and Küpper-Weisser winter service equipment. MAN manufacturer's warranty until 02.12.2026 Equipment: Ndsdsyv Tt Aopfx Akqjc Mileage approx. 441 delivery kilometers 18,000 kg permissible gross vehicle weight 22,000 kg technically permissible gross vehicle weight for winter service 9,000 kg permissible front axle load 10,000 kg technically permissible front axle load for winter service operation up to a maximum of 62 km/h 11,500 kg permissible rear axle load, 13,000 kg technically permissible rear axle load Winter service hydraulics, 2-section system with quick couplings, manufacturer Küpper-Weisser Front mounting plate, type F1/C, according to DIN EN 15432-1 with hydraulic connections Winter service lighting Preparation for additional lighting on the vehicle rear Heated windshield Preparation for 2 hydraulic pumps on the engine, 11 cm and 22.5 cm (for external attachments) TGS NN medium cab with rear window Wheelbase 3,900 mm Engine Euro 6 e Drive 4x4 Front axle as external planetary axle, driven, switchable High configuration Differential lock in front and rear axles Meiller 3-sided tipper, approx. 4.80 m x 2.42 m x 0.60 m high Front wall 0.80 m high Side panels, M-Jet, steel HB 450, 2.5 mm Floor of the loading platform made of steel HB 400, 4 mm Tie-down points fully recessed in the floor panel Side walls of the tipper, pivoting and foldable, deep latches Rear wall of the tipper, pivoting with automatic latch Transfer case MAN G172 with on-road and off-road gears MAN TipMatic 12.26 OD Transmission function MAN Idle Speed Driving Driving program MAN TipMatic Efficiency, up to 70,000 kg Driving program MAN TipMatic Offroad, up to 70,000 kg Driving program MAN TipMatic Manoeuvre, shunting mode Air conditioning, Climatronic Auxiliary heater, 4 kW Trailer coupling, Ringfeder type RF40/G150A with compressed air connections Tipping hydraulic connection at the rear Front axle with leaf springs, rear axle with air suspension Front axle AP 9 tons, rear axle AP 13 tons Stabilizer for front and rear axles MAN Comfort Steering Hill start assist MAN EasyStart Full brake assist Lane departure warning LDW EBS ASR ESP ABS Offroad with additional off-road logic Cruise control High-performance engine brake MAN EVBec, adjustable 390-liter aluminum tank, right side Sun visor 2 rotating beacons and 2 work lights Dustbox in the cab Reversing warning, audible, can be switched off when reversing gear is engaged Reversing camera Multi-function steering wheel MAN EasyControl control panel, 2 functions can be operated from the outside when the door is open Electrically adjustable and heated exterior mirrors Electric windows MAN Media System Advanced 7 inches MAN sound system Smartphone integration Driver comfort seat with air suspension, lumbar support, shoulder adjustment and heating Seat covers in comfort quality Municipal new vehicle with registration date 02.12.2025 Archive images Price NET, plus 19% VAT. We will gladly provide you with attractive financing offers. All information without guarantee. Errors and prior sale excepted. Internal vehicle number: 2517

Condition: good (used), Year of construction: 2016, functionality: fully functional, Includes 1 arm. Njdpez Dv Dnofx Akqjdc

Condition: new, Year of construction: 2026, DCV4500 VIBER – Modern Industrial Dust Extraction System with Automatic Filter Cleaning Nsdpfxeuc Unqo Akqedc The DCV4500 VIBER is a modern industrial dust extraction system designed for continuous, efficient, and quiet operation in demanding woodworking environments. The unit ensures stable extraction performance throughout the entire operating cycle, minimizing the risk of efficiency losses and production downtime. Main Advantages of the Machine VIBER system – automatic filter cleaning without interrupting operation. Full upper enclosure – significantly reduces noise and vibrations. Extraction capacity of 4500 m³/h – ensures effective dust removal even with several machines operating simultaneously. Highly sealed system design – prevents heat losses and guarantees clean air in the production hall. New safety protection system – improves operational reliability. Metal rotor – dynamically balanced for quiet and vibration-free operation. Design and Technology The machine is based on a reinforced, hardened steel construction. Its compact dimensions allow the extractor to be installed close to a wall or between machines without limiting the available working space. Metal waste containers equipped with viewing windows and a mobile system enable quick emptying and easy monitoring of filling levels. Service doors provide convenient maintenance access and simplify the replacement of filter bags. Precision and Work Efficiency The dust extraction fan used in the DCV4500 VIBER provides an air suction speed of 28–32 m/s. Thanks to the specially designed rotor blade geometry, maximum efficiency is achieved with minimal energy consumption. At the same time, filtration down to 5 microns effectively captures fine dust particles, improving workplace air quality and enhancing the final quality of processed materials. Applications The DCV4500 VIBER is an advanced central dust extraction system ideal for: woodworking plants, furniture manufacturers, producers of wooden components. It efficiently supports machines such as sanding machines, panel saws, edge banders, and other equipment generating large amounts of dust and chips. Its reliable operation makes it suitable for both serial production and intensive industrial use. Standard Equipment Control cabinet with ON/OFF function 18 polyester filters with filtration efficiency down to 5 microns Metal waste containers with viewing windows Full sound-insulated enclosure Technical Specifications Parameter Value Motor power (S1) 3.0 kW Power supply 400 V / 50 Hz Motor speed 3000 rpm Extraction capacity 4500 m³/h Negative pressure 3000 Pa Noise level 80 dB Suction port diameter 200 mm Air velocity 28–32 m/s Filtration area 6 m² Number of filters 18 Filter material Polyester, 5 microns / filter category "G" Dimensions 752 × 1502 × 2200 mm Weight 220 kg

Condition: new, mileage: 50 km, power: 100 kW (135.96 HP), color: white, gearing type: automatic, emission class: euro6, Equipment: ABS, air conditioning, central locking, power assisted steering, - Rear air suspension - Front air suspension Ndsdpfx Aeyrw Rvskqec - Mr. Rudolph will be happy to assist you by phone at: Engine: 2.3 l D EVIe 100kW (136hp), HI-MATIC 8-speed automatic transmission, rear axle suspension: air suspension, rear axle: single wheels, vehicle version: standard chassis with cab, wheelbase: 3450 mm, standard configuration, seats non-heated, passenger seatbelt pretensioner, seats upholstered in fabric, AIR PRO control elements in cab, Connectivity Box 4G incl. TCO service contract, front headlights halogen, EU control device, delete option, light and rain sensor, manual high beam control, bodybuilder interface, tinted windows, rear parking sensors, fuel filler neck in B-pillar, standard vehicle plaque, tire pressure monitoring system (TPMS), emergency brake assistant AEBS with City Brake, MY 2024, standard rear lights, electrically adjustable and heated exterior mirrors, cab width 2000 mm, driver drowsiness detection (Driver Drowsiness Attention Warning), central locking with remote control, speed limiter 160 km/h, COC certificate of conformity, rear wall insulation, traffic sign recognition with intelligent speed assistant (ISA), electric windows for front doors, front airbags for driver and passenger with seatbelt pretensioners, first aid kit, spare wheel mounted at rear frame, 20-liter AdBlue tank under cab, trailer load 3.5 t, spare wheel, dimension matches chassis tires, rear underrun guard, ESP system, steel wheels, 86-liter fuel tank between frame rails, standard single-leaf front transverse spring (plastic), C-profile steel ladder frame, standard suspension, front axle, rear air suspension adaptive, rear axle ratio i 3.59, comfort sound insulation, additional speed limiter, switch for body lighting, 12V 13-pin trailer socket, rear blind spot radar, lane change assistant with door opening warning on both sides + turn assist passenger side, rear-view camera included loose, mirrors for body width 2200 mm, cab rear wall with window, proximity monitoring (MOIS), additional vehicle key with remote control, storage box next to driver's seat with USB port, overhead storage above windshield, adaptive cruise control (ACC) with Stop & Go, grab handle on A-pillar, tires 235/65 R16, ball-type trailer hitch, Eco-Smart function, delete option, White IC 194, generic tire, printed operation and maintenance manual, USB sockets driver and passenger side, My Iveco Infotainment 10-inch with navigation, Alexa voice assistant integrated, passenger bench with multifunction tray and storage compartment, fog lights, air conditioning with climate control, comfort headrests, comfort driver's seat with armrest and lumbar support, height, tilt, and longitudinal adjustment, hydraulically cushioned, leather steering wheel, intelligent traffic jam assistant (TJA), lane centering plus (LC), electric parking brake, and much more. We are happy to provide you with an offer for your vehicle trade-in. If you wish to lease or finance your vehicle, we are pleased to prepare an individual offer for you. Subject to errors and prior sale! Mr. Rudolph will be happy to assist you by phone at: For further information, please visit our homepage: ... ESP, navigation system, particulate filter Engine displacement: 2,287...

Condition: new, power: 353 kW (479.95 HP), first registration: 01/2026, fuel type: diesel, tire size: 385/65-22,5, axle configuration: 6x4, wheelbase: 3,600 mm, fuel: diesel, fuel tank capacity: 390 l, color: white, driver cabin: day cab, gearing type: automatic, emission class: euro6, suspension: steel-air, loading space length: 52,000 mm, loading space width: 24,200 mm, loading space height: 8,000 mm, Year of construction: 2026, Equipment: ABS, AdBlue, Bluetooth, EBS, air conditioning, central locking, crane, cruise control, differential lock, electric window regulation, electronic stability program (ESP), navigation system, onboard computer, power mirror, seat heater, soot filter, trailer coupling, - Aluminum fuel tank - Rear work lights - Heated exterior mirrors - Heated mirrors Njdpfx Aeyllctskqedc - Passenger seat - Differential lock - Speed limiter - Catalytic converter - Automatic climate control - Refrigerator - Air suspension - Air-suspended seats - Particle filter - PTO - Radio/Multimedia system - Disc brakes - Seat heating - Sun visor - Lane keeping assistant - Stability control - Toolbox - Windshield Internal number for customer inquiries: 3-198 MAN TGS 26.480 6x4 three-way tipper with FASSI F195A.2.24 E-DYNAMIC loading crane Loading crane: FASSI F195A.2.24 e-dynamic Lifting moment 162 kNm (16.51 mt) Hydraulic four-stage extension boom 12.7 m e-dynamic hose system for 2 auxiliary devices Slew range 400° Double knuckle boom system with PROLINK (overextension of the knuckle arm up to 15°) Electronic overload cut-off system with FX 500 FASSI stability control FSC incl. LMB II Fassi RCS Funk maxi - 6 functions with 3 joysticks (2-2-2) Special outriggers, outrigger width 6.64m hydraulically extendable incl. FSC Outriggers can be operated via radio remote control FL system (Full Lift), switchable quick-action valve for the extension booms LED work lights Vehicle: Diesel engine MAN D2676 LFAI, 352 kW (480 hp) power, 2,400 Nm torque, Euro 6e Automatic transmission MAN TipMatic 12.26 OD Driving program MAN TipMatic Performance, Efficiency and Offroad, up to 70,000 kg Drive 6x4 Suspension leaf/air Differential locks on driven rear axles 3,600 mm main wheelbase, 1,400 mm wheelbase between rear axles 310 l fuel tank volume, 60 l AdBlue tank volume Full brake assist High-performance engine brake MAN EVBec, adjustable Disc brakes on front axle, drum brakes on rear axles Trailer coupling RINGFEDER type 4040/G150A Cab NN: the practical one (narrow, medium length, normal height) Tilt roof, mechanical Driver comfort seat, air-suspended, with lumbar support, shoulder adjustment and seat heating MAN EasyControl control panel, 4 functions, operable from the outside when the door is open Sun visor front windshield, inside, electric Cool box MAN SmartSelect infotainment control with touchpad and direct access buttons MAN Media System Navigation Advanced 7 inch MAN Sound System Advanced Navigation map Europe and Russia Online traffic for navigation function Standard extension warranty for powertrain for 3rd operating year up to 450,000 km, subject to maintenance records Superstructure: Three-way tipper body with FASSI F195A.2.24 E-DYNAMIC crane mounted directly behind the cab Body: Dimensions L x W x H 4,800 mm x 2,420 mm x 800 mm (Alternatively also available: loading area length 5,200 mm x 2,420 mm x 800mm ) Front wall 1,000 mm high Special equipment: - Rear corner pillars fixed - Lifting aids for the side walls - Eight lashing eyes recessed on the left and right in the floor (4 per side) - Hydraulic crane/tipper/trailer switchable via valve in the cab - Positioning of the underrun protection, the tail lights and the supply lines on the left - Central locking for opening...