Used Operating Instructions for sale (25,883)

Condition: used, Year of construction: 1999, sheet width 3060 mm plate thickness 8.0 mm thickness at "Niro-steel" 6.0 mm distance between columns 3100 mm down holder 16 Stück no. of strokes max. 10 - 15 Hub/min oil volume 160 ltr. cutting angle 1.6 ° back stop - adjustable 6.0 - 750 mm Control ELGO P9521 total power requirement 18.5 kW weight 6300 kg range L-W-H 3900 x 2300 x 1630 mm Features: - Robust electro-hydraulic swing beam shear - ELGO digital display model P9521, for electric backgauge * Backgauge travel X = 750 mm * Backgauge-free ball screw drive * Travel speed 100 mm/s - 1x stable side stop * With T-slot, flip-stop, and millimeter scale - 2x stable front support arms - Electric cutting length limiter * Cutting length limiter to increase the stroke rate/min. Kwjdpfx Aboxaci Eo Teu - Manual cutting gap adjustment * Centrally operated on the right side stand - Front support plates - Front finger/interference guard - Inching operation with push buttons on the left control panel - Protective grille = safety device behind the machine - Operating instructions (PDF)

Condition: used, Year of construction: 2000, sheet width 3060 mm plate thickness 6.0 mm thickness at "Niro-steel" 4.0 mm distance between columns 3100 mm down holder 16 Stück no. of strokes 20 Hub/min oil volume 160 ltr. cutting angle 1.6 ° Control ELGO Number of working hours ~ 1.100 h total power requirement 11.0 kW weight 5250 kg range L-W-H 3800 x 1940 x 1560 mm from a maintenance workshop Kwedpfsxacfasx Ab Tju with only approx. 1.100 operating hours (!!) Equipment: - electro-hydraulic swing beam shears - ELGO NC control unit * for electric back stop * Input of target/actual position value possible - NC electro-motoric back stop * travel path of back stop X = 750 mm * back stop ball screw with no play * travel speed 100 mm/sec - electric cutting length limitation * cutting length limitation to increase the number of strokes/min. - manual cutting gap adjustment, via eccentric - tip operation with push buttons on the control panel on the left - front support plates with ball rollers - front finger/interference protection - 1x side stop with T-slot & millimeter scale - 2x front support arms - original operating instructions including CE declaration

Condition: ready for operation (used), Year of construction: 2017, turning length 4000 mm turning diameter 850 mm turning dia. in gap 1150 mm turning diameter over slide 520 mm turning speeds 5.0 - 630 U/min quill: 6 MK quill travel 250 mm spindle bore 100 mm workpiece weight max. 4000 kg bed width 600 mm travel -x axis 500 mm travel -z axis 3700 mm rapid traverse X 1800 mm/min rapid traverse Z 3640 mm/min feeds X : 0.04 - 4.8 mm/min feeds Z : 0.08 - 9.6 mm/min feeds Z1 : 0.02 - 2.4 mm/min engine output 20.0 kW weight of the machine ca. 6800 kg. dimensions 6150 x 1500 x 1500 mm good / well-maintained condition (!!) original price at the time approx. 65.000 euros special price on request Kwjdpfjxabh Tsx Ab Tsu Description: - particularly heavy, heavily ribbed and wide machine bed - in a rigid one-piece monoblock design - induction-hardened and ground guide prisms - guarantee long-term accuracy and minimal wear - solid headstock - with high-precision, tapered roller bearing main spindle . and 100 mm spindle bore - excellent smooth running at maximum spindle speed - joystick switch for X and Z feed directly on the support - manually switched 4-stage countershaft gear, - powerful main spindle motor enables exact adjustment of the speed . and high torque for heavy machining - rapid traverse for X and Z axes enables quick positioning of the support . and reduces idle times - adjustable overload clutch in the lock case protects the feed mechanism . against damage and failures - central, handy control for feeds and thread pitches - the feed gear offers a wide range of . diametric, inch, module and metric threads - support and top slide are designed for large cutting forces - higher working precision - user-friendly functions Scope of delivery: - SINO position indicator - TOS 3x jaw chuck .. Ø 400 mm - 4-jaw faceplate chuck Ø 800 mm - 4-way tool holder - Fixed steady rest 40-350 mm - Follow-on steady rest 30-120 mm - Fixed centering point - Reducing sleeves - Chuck protection - Coolant device - Machine leveling feet - Work light - Operating tools - Operating instructions

Condition: ready for operation (used), Year of construction: 2000, pressure 170 t chamfer lenght 3170 mm distance between columns 2700 mm column arm 420 mm dayligth 470 mm stroke 200 mm ajustment speed 100 mm/sec working feed 10.0 mm/sec return speed 100 mm/sec Kedpfx Ajxabgpeb Tswu table width 180 mm table height 960 mm oil volume 235 L 0 300 bar controlled axis 6 Anzahl Number of working hours 29.400 h total power requirement 16.5 KW weight of the machine ca. 11910 kg range L-W-H 4025 x 2020 x 2900 mm well-maintained condition (!!) with only approx. 29.400 operating hours - in checked condition - machine video - ?v=APP0HZjMms4 Equipment: - electro-hydraulic CNC press brake - AMADA CNC control "OPERATEUR 2" - 6 axes (X, Y1 + Y2, R, Z1 + Z2) * swiveling operation - front left * tool & program library - CNC-controlled back stop adjustment (X-axis) * adjustment range .. 700 mm - CNC-controlled vertical adjustment of the stop fingers (R-axis) * adjustment range .. 250 mm - CNC-controlled adjustment of the stop fingers left-right (Z1 + Z2) - hand control unit for manual movement of the axes - AMADA manual upper tool clamping system - AMADA Rehfuß upper tools - divided - AMADA Lower tool holder - incl. 1x V die (not complete) - AMADA DIGI PRO - gigital angle measuring system - 1x freely movable double foot switch - side protective device (swinging doors) - rear protective device (swinging door) - EMERGENCY OFF button at the front - Operating instructions (ENG)

Condition: used, Year of construction: 2007, Technical details: weight of the machine ca.: 24 t dimensions of the machine ca.: 3900 x 3500 x 2500 m -the machine has no B axis Kwedpfx Abex Aq Ete Teu -two grinding spindles with one grinding wheel each - The transport instructions can be found in the documentation (attachment). including Hoffmann KSM filter system Loading list available Operating data v. : Operating time: 21727 h / production time: 11960 h Machine documentation: 1 set of circuit diagrams, electrical plans, operating instructions Accessories: 2 replacement measuring heads Marposs S/500; prism supports Other: Hoffmann KSM filter system Machine condition: according to age, due to processing with emulsion *

Condition: used, Single-column eccentric press RICHTER type PEKRS 80 Year of construction 1970 - overhaul 2024 Compressive force 80 ton. throat depth 350 mm Table size 900 x 650 mm Hole in the clamping table Ø 200 mm ram surface 700 x 500 mm Stroke rate 70 strokes/min. Stroke adjustment 6 - 100 mm ram adjustment 85 mm Installation height max. 400 Clamping pin bore Ø 50 mm Table height above floor 810 mm Motor power 8 kW Mains connection 400 Volt, 50 Hz - ORTLINGHAUS pneumatic clutch/brake combination - HERION XSz 32 press safety valve Ksdpfx Aei Db Ibob Towu - Pneumatic ram compensation cylinder - Overload protection with breaker plate in ram - Central grease lubrication with hand pump Space requirement L x W x H 1800 x 1250 x 2830 mm Weight 5.7 tons Very good condition Technically overhauled and converted to the latest UVV with new electrics Control conversion in 05/2024 - suitable for manual insertion work - in accordance with DGUV Information 209-030 Press inspection and Machinery Directive 2006/42/EC Low Voltage Directive 2014/35/EU EN ISO 16092-1: Safety of machine tools - Presses - Part 1: General safety requirements EN ISO 16092-2: Machine tools - Safety of presses - Part 2: Mechanical presses - Control system with plain text error messages and diagnostic screen for rapid fault localization - New electrical cabinet, mounted on the side of the machine - completely based on SIEMENS, with PLC S7-1200 PROFIsafe and 7" TFT touch display - Two-hand control panel with emergency stop and engagement lock - el. foot switch - Cam switch unit with run monitor control - Stroke release via HERION XSz 32 press safety valve with pneumatic pressure compensator - New wiring of the machine - Updated operating instructions The machine is equipped with 6 operating modes: 1 = Set-up 2 = Single stroke two-handed 3 = Single stroke foot 4 = continuous run foot 5 = automatic continuous run 6 = reverse run

Condition: used, Surface grinding machine BLOHM type HFS 6 make no.: 10493 year of construction 1973 Electro magnetic clamping plate 600 x 300 mm grinding length 600 mm grinding width 400 mm table longitudinal movement max. 650 mm transversal movement 350 mm distance spindle center - table surface max. 600 mm distance spindle center - magnetic plate max. 517 mm Clamping surface table 1020 x 300 mm grinding wheel diameter 300 mm grinding wheel width 50 mm grinding wheel bore 76 mm table longitudinal feed 2-30 m/min infinitely variable table cross feed 2-65 mm stepless electric cross feed 3 m/min vertical feed 0,001 - 0,020 mm per infeed pulse vertical feed 0,250 m/min grinding wheel speed 1400 / 2800 rpm. Motor power hydraulic pump 2,2 kW Motor power grinding spindle 5 / 6 kW Mains connection 380 Volt, 50 Hz. Total power 11 kW - automatic depth adjustment - hydraulic longitudinal table movement - grinding wheel dresser on the headstock - electromagnetic plate height 83 mm - coolant system adjacent, with magnetic filter in filter housing - grinding spindle circulating lubrication - adjacent control cabinet (800 x 500 mm) - swiveling control panel - operating instructions and spare parts manual space requirement L x W x H 3000 x 2200 x 2100 mm weight surface grinding machine 3000 kg weight switch cabinet 200 kg good condition Kjdpfx Aod Hbafsb Tewu

Condition: used, Double-column hydraulic press NEFF Type RHS 125 Z Hydraulic drawing press Machine No. 3973 Year of manufacture 1983 Pressing force: 125 tons Column gap: 1050 mm Lateral column clearance: 550 mm Table size: 1000 x 800 mm Ram size: 1000 x 800 mm Ram stroke: 350 mm Installation height max.: 750 mm Table height above floor: 960 mm Blankholder force: approx. 12 tons at 105 bar Blankholder stroke: 100 mm Through-hole in table: Ø 202 mm Rapid advance speed downwards: approx. 360 mm/sec Kjdoguvtlepfx Ab Tswu Rapid advance speed upwards: approx. 360 mm/sec Working speed: approx. 36 mm/sec Oil tank capacity: approx. 1000 liters Main pump motor power: 22 kW Control pump motor power: 4 kW Control pump motor power: 2.2 kW Electrical connection: 400 Volt, 50 Hz - Hydraulic blankholder cushion underneath the table with a through-bore in the table top Ø 202 mm - Precise 4-column guide on the ram corners - Infinitely variable pressing force adjustment - Electrically adjustable fixed stop via hydraulic motor - Cutting shock damping - Two-hand control panel for stroke release on the press - Free-standing control cabinet (1600 x 500 mm) - Documentation such as operating instructions, electrical wiring diagram, and PLC program printout available Required space L x W x H: 2600 x 2400 x 4270 mm Weight: approx. 14 tons Good condition

Condition: used, Tool grinding machine, twist drill grinding machine BORA -- BI-EMME s.n.c. (Italy) Type 1/BM 40 No. 49697 Year of manufacture 1997 Grinding range Ø 3 - 40 mm Center angle 40° - 180 Motor power 1.1 kW Grinding wheel dimension max. Ø 200 mm Grinding wheel speed 2840 rpm Mains connection 400 Volt, 50 Hz - For grinding standard drills and other tools with 1, 2, 3, 4 or 6 cutting edges (step drills, taps, countersinks, drills with a thick core and drills with special grinding) - Precision six-jaw chuck Ø 125 m - pointing device (motor power 0.18 kW) - For left and right cutting drilling tools thanks to interchangeable cams - Cam disks easily interchangeable for 2 or multi-bladed tools - 4 cam disks - Centering arbor for MK1, MK2, MK3, MK4 Kjdpfxenzt A He Ab Tewu - A white grinding wheel with a diameter of 170 mm and a width of 40 mm is installed - Metal base with door and shelf - Wet grinding unit shown opposite - Operating instructions per PDF Space requirement L x W x H 900 x 850 x 1250 mm Weight 220 kg Very good condition

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel Kedpfsu Rwa Ijx Ab Tswu - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, Filter system - extraction system, central extraction Cartridge - pulse filter VALCO type Pidclean 4N Central welding fume extraction system Series. No.: 15003 Year of construction 2003 Volume flow max. 3500 m³/h Filter area 92.8 m² Differential pressure 700 Pa Suction connection at filter inlet Ø 250 mm Exhaust air connection at filter outlet 225 x 160 mm Compressed air requirement 4 to 6 bar Motor power 5.5 kW Mains connection 400 Volt, 50 Hz - AUTEL filter control unit, type Eco S6 - Pneumatic filter cleaning, automatic via control unit - 4 cartridge filters Ø 350 x 660 mm - Maintenance flap for filter change - Radial fan on top of the system - Removable dirt collection container approx. 40 liters - Silencer for fan outlet, Ø 250 mm - Electrical diagram and operating instructions for the control unit available Space requirement L x W x H 2150 x 1350 x 2560 mm Kwodpfx Abomquwqj Teu Weight approx. 550 kg Good condition

Condition: used, Hydr. hacksaw, metal saw, lifting saw KASTO type PSB WBS 210 / 230 Machine. No. 115 106 1212 / 72783 Year of construction 1986 Kwsdpfeifu Ayjx Ab Tou sawing area - round Ø 250 mm sawing area - square 225 x 225 mm sawing range - rectangle 260 x 100 mm Cutting speed 11 -13 - 17 - 22 - 26 - 34 m/min. saw blade length 400 mm motor power 1,4 and 1,8 kW pole changeable mains connection 380 Volt, 50 Hz - only for 90° cuts, no miter adjustment - Saw motor with 2 speeds and 3 V-belt stages - Hydraulic saw bow feed - hydraulic cutting pressure adjustment via throttle valve - rapid motion for saw bow lowering - manual height adjustable material support table with mm scale via hand wheel - manual material clamping - coolant device in machine base - operating instructions space requirement L x W x H 1500 x 700 x 1550 mm weight 590 kg very good condition

Condition: used, AC Spot Welding Machine, Projection Welding Machine ARO Type MA 350 DC AC Resistance Welding Machine Mach. No. MA35031332 / 9731122B110 Year of Manufacture 1997 Power at 50% duty cycle: 30 kVA Power at 100% duty cycle: 21 kVA Maximum welding power: 156 kVA Thrust 550 mm Electrode arm diameter: 60 mm Electrode holder diameter: 25 mm Cylinder stroke max. 80 mm Electrode force max. 730 daN (at 6 bar), continuously adjustable Kwjdpfx Abehpf Iys Tju Operating air pressure 0.5 to 6 bar Mains connection 400 volts, 50 Hz Connected load 75 kVA / 63 amps / Cable cross-section 3x 16 mm² Maximum possible sheet pairing: 5 mm + 5 mm - ARO Micro welding control system 2X16 III Version 6Z2P Type 1B (6 times - 2 programs) - Continuous welding current adjustment via thyristor module - Parallel electrode guide - Double-stroke welding cylinder (pre-stroke / welding stroke) - Single-stroke and continuous spot welding modes - Electrode force continuously adjustable via air pressure - Water-cooled by external water cooling (water cooling unit not included) - Electric foot switch - Control cabinet with control system permanently mounted on the machine - PC interface RS 485 - Spot weld counter - Operating instructions for control system, spot welder, and electrical diagram included Space requirement: W x H x D 520 x 1550 x 1150 mm Weight: 290 kg Very good condition

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet - 2-hand control panel adjacent - ground level installation - central lubrication - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. Kjdpfsdzp Tcjx Ab Tewu The machine was used as a production press at Volkswagen until 2000. From 2000 the machine was used as a tool testing press in a tool shop. good condition

Condition: excellent (used), functionality: fully functional, input voltage: 230 V, DGUV certified until: 03/2027, total width: 410 mm, total length: 410 mm, total height: 530 mm, empty load weight: 15 kg, input frequency: 50 Hz, year of last overhaul: 2026, overall weight: 15 kg, electrical fuse: 10 A, power: 1 kW (1.36 HP), Hobart Cream Whipper G 5 R-FC Tabletop model for 3–5 liters of cream Easy operation Timer: 1 to 6 minutes Stainless steel bowl Connection: 220V Dimensions: 410 x 410 x 530 mm (W x D x H) Kedpfxjxmrams Ab Tewu Used device, cleaned With warranty and spare parts service Quality from a specialist dealer! Benefit from over 35 years of experience! Options: Maintenance contract Spare parts box for added security Delivery service Instruction & commissioning Further cream whippers available from stock!

Condition: used, Year of construction: 1995, sheet width 3000 mm plate thickness 4 mm Kwjdpfx Abeyk Diis Teu work height max. 900 mm 450 mm total power requirement 5,5 kW weight of the machine ca. 4800 kg dimensions of the machine ca. 4250 x 1500 x 1850 mm Equipment: - electric bending angle adjustment - electric upper beam adjustment - foot switch - operating instructions

Condition: used, Year of construction: 2000, sheet width 3020 mm plate thickness 5 mm distance between columns 3020 mm Control Simatec OP7 stroke 450 mm back stop - adjustable 1000 mm work height max. 900 mm total power requirement 22 kW weight of the machine ca. 9000 kg dimensions of the machine ca. 4200 x 1600/2900 x 2000 mm Features: - Motorized backstop, 1000 mm Kwjdpeyk Dicjfx Ab Teu - Motorized upper crossbar adjustment - Motorized lower crossbar adjustment - Side protection - Foot switch - Operating instructions

Condition: used, Year of construction: 2009, sheet width 3050 mm plate thickness 6 mm rear stop 10-1000 mm cutting angle 0,5 - 2,5 ° down holder 20 Stk no. of strokes 14 - 23 Hub/min Kjdpeyk Dhxefx Ab Towu work height max. 900 mm oil volume 140 l total power requirement 11 kW dimensions of the machine ca. 4000 x 2150 x 1900 mm weight 7800 kg Equipment: - ELGO control unit type P50 - Automatic cutting angle adjustment - Automatic cutting gap adjustment - electric back gauge - Pneumatic sheet holding device - Light barrier behind the machine - 4 support arms - front finger guard - foot switch - Angle stop Operating instructions

Condition: good (used), Year of construction: 1979, roll diameter 420 mm throat 410 mm workpiece height 265 mm saw band length 3150-3260 mm width of saw-band max. 16 mm table-size 600 x 600 mm work height max. 1000 mm total power requirement 1,1/1,7 kW weight of the machine ca. 0,51 t dimensions of the machine ca. BTH 740x920x1815 mm - Includes welding equipment - Includes grinding equipment - Includes work light - Includes semi-hydraulic weight feeder Kjdpfx Abeyg Raao Tjwu - Includes tilting work table - Includes operating instructions

Condition: used, Year of construction: 1980, x-travel 300 mm y-travel 160 mm z-travel 340 mm tool taper SK40 Speed 40-2000 U/min. control Aktiv HEIDENHAIN table-size 600 x 210 mm total power requirement 2 kW weight of the machine ca. 0,73 t dimensions of the machine ca. TBH 1200x1100x1600 m Kwedpfx Absw A Apyo Teu - Active feed in the X and Z axes - Additional swiveling table 600 x 210 mm - Coolant system - Counter bearing for horizontal milling - Several fixtures and clamping devices/milling cutters - Operating instructions

Condition: used, Year of construction: 1980, x-travel 300 mm y-travel 160 mm z-travel 340 mm tool taper SK40 Speed 40-2000 U/min. control Aktiv HEIDENHAIN table-size 600 x 210 mm total power requirement 2 kW weight of the machine ca. 0,73 t dimensions of the machine ca. TBH 1200x1100x1600 m - Active feed in the X and Z axes - Additional swiveling table 600 x 210 mm - Coolant system Kedpsw A Ap Hefx Ab Tswu - Counter bearing for horizontal milling - Several fixtures and clamping devices/milling cutters - Operating instructions

Condition: used, Year of construction: 2007, Condition: used Kedpfxjhtu U Rj Ab Tswu Location: Bremen Other: The M-Pulse metal detector is a highly sensitive device for the reliable detection of metallic foreign objects. It uses an inductive measuring method with a balanced coil system. The metal detector is exclusively designed to detect metallic foreign bodies in pasty or liquid media. A more detailed description of the machine can be found in the existing operating instructions.

Condition: good (used), Year of construction: 2000, pressure 40.0 t Kwodpoyk E Umofx Ab Tju chamfer lenght 1600 mm distance between columns 1100 mm stroke of upper beam 100 mm throat 195 mm working feed 10.0 mm/sec return speed 70.0 mm/sec 180 bar work height max. 840 mm table width 110 mm dayligth 295 mm Control ATL 550 total power requirement 5.5 kW weight 2500 kg range L-W-H 2100 x 1200 x 1800 mm Equipment: - NC-controlled hydraulic press brake, with torsion shaft - with ATLANTIC NC control - model "ATL 550" * Positioning of the backgauge (X axis) * Positioning of the depth adjustment (Y1 Y2 axis) * Possibility of programming different programs * Memory capacity max. 200 programs - max. 400 blocks * Swivel control panel, left front - Electro-motorized backgauge (X axis) * with 2x stop fingers, manually adjustable (R Z axis) - Tool holder system A - with top wedge crowning - Split insert/bending tools - Lateral safety guards - rear safety guard - 1x freely movable double foot switch - Operating instructions (PDF)

Condition: good (used), Year of construction: 2000, pressure 40.0 t chamfer lenght 1600 mm distance between columns 1100 mm stroke of upper beam 100 mm throat 195 mm working feed 10.0 mm/sec return speed 70.0 mm/sec 180 bar work height max. 840 mm table width 110 mm dayligth 295 mm Control ATL 550 total power requirement 5.5 kW weight 2500 kg range L-W-H 2100 x 1200 x 1800 mm Equipment: - NC-controlled hydraulic press brake, with torsion shaft - with ATLANTIC NC control - model "ATL 550" * Positioning of the backgauge (X axis) * Positioning of the depth adjustment (Y1 Y2 axis) * Possibility of programming different programs * Memory capacity max. 200 programs - max. 400 blocks * Swivel control panel, left front Kwedjyk E Utopfx Ab Teu - Electro-motorized backgauge (X axis) * with 2x stop fingers, manually adjustable (R Z axis) - Tool holder system A - with top wedge crowning - Split insert/bending tools - Lateral safety guards - rear safety guard - 1x freely movable double foot switch - Operating instructions (PDF)

Condition: new, I-beam section - upend 100 x 20 (d 2100) mm bar material dia. max. 100 x 3 (d 3000) mm L-beam 80x80x8 (d 2000) mm square material 50 x 25 x 2 (d 600) mm I - beam section - flat steel 120 x 30 (d 600) max.140b mm bar material - diameter 60.0 (d 1000) mm tool taper 80.0 mm oil volume 100 Liter turning speeds 4.2 m/min. weight 1600 kg range L-W-H 1240 x 1375 x 1540 mm Equipment: Kwodexcukgspfx Ab Tju - electro-hydraulic ring/profile bending machine - hydraulic bottom/side roller adjustment * for extra small bending radii - bottom/side roller can be adjusted individually - 3x driven rollers - divided roller segments - digital position display of the bottom/side rollers * Display with touchscreen function - hardened tool holder (42CrMo4) - machine base - 2x hydraulically adjustable side guides - horizontal and vertical work possible - freely movable control panel - pressure gauge / pressure display for the rollers - CE mark / declaration of conformity - operating instructions in German