Used Manual Lathe for sale (19,197)

Condition: used, L + Z Lathe VOEST ALPINE - WEILER Type DA 210 / 1 Machine No. 1-004/2552 Year of manufacture: 1983 Centre distance: 1000 mm Swing over bed: 420 mm Centre height over bed: 210 mm Swing over cross slide: 240 mm Centre height over cross slide: 120 mm Spindle bore: 52 mm Spindle speed: 33 - 1500 rpm, 12 steps Chuck flange: short taper DIN 55027 size 6, 4x M12 Tailstock taper: MK 4 Motor power: 5.5 kW Power supply: 380 Volt, 50 Hz - Spindle speed via 12 gearbox steps - EMCO 3-jaw scroll chuck Ø 200 mm with turning and boring jaws - Multifix size B quick-change tool post with 3 change cartridges - Automatic longitudinal and face feed - Coolant system - Spindle brake - Emergency stop - Machine lamp Iajdpeykca Hsfx Abren - Operating manual Space requirement (L x W x H): 2200 x 1200 x 1450 mm Weight: 1400 kg Very good condition

Condition: used, L + Z Lathe WEILER Type Praktikant 800R Machine No. 3309 Year of manufacture: 1984 Centre distance: 800 mm Swing over bed: 280 mm Swing over cross slide: 160 mm Centre height over bed: 140 mm Centre height over cross slide: 80 mm Spindle bore: 36 mm Feed: longitudinal and face Chuck mount: short taper DIN 55027 size 5, 4x M10 Tailstock taper: MK 3 Quill travel: 90 mm Spindle speed: 42 - 2000 rpm Drive power: 1 / 1.6 kW Mains connection: 380 Volt, 50 Hz Iaedpfx Asyg Rfiobrjn - Spindle speed via 2 motor speeds and 8 gear steps - 3-jaw scroll chuck BILSING Ø 160 mm with 1 set of stepped jaws and 1 set of soft jaws - MULTIFIX size A quick-change toolpost with 3 interchangeable holders - revolving centre - emergency stop - folding chuck guard - coolant system - very low operating hours Space requirements L x W x H: 1900 x 700 x 1300 mm Weight: 600 kg Very good condition

Condition: used, Harrison M300 Manual Lathe, 160mm 3 Jaw Chuck, Quick Change Tooling, Distance Between Centres 110mm, 2500rpm. S/No. 307209. Country of Origin: United Kingdom Location: These lots are located in Leamington Spa, UK. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. All/Any tooling is being offered as specifically described. Iodpjyidtiefx Abrsan

Condition: used, L + Z Lathe VOEST ALPINE - WEILER Type DA 210 / 1 Machine No. 1-004/2581 Year of manufacture: 1984 Centre distance: 1000 mm Swing over bed: 420 mm Centre height over bed: 210 mm Swing over cross slide: 240 mm Centre height over cross slide: 120 mm Spindle bore: 52 mm Spindle speed: 33 - 1500 rpm, 12 steps Chuck flange: short taper DIN 55027 size 6, 4x M12 Tailstock taper: MT 4 Motor power: 5.5 kW Electrical connection: 380 Volt, 50 Hz - Spindle speeds via 12-step gearbox - 3-jaw scroll chuck AROWA Ø 200 mm (only one set of chuck jaws) - Multifix quick-change tool post, size B, with 3 tool holders - Automatic longitudinal and cross feed - Coolant system - Spindle brake - Emergency stop - Splash guard Iaodjyah Rvepfx Abron - Fixed steady rest Ø 160 mm - Machine lamp - Operating manual Space requirement (L x W x H): 2200 x 1200 x 1450 mm Weight: 1500 kg In very good condition

Year of construction: 1970, condition: used, functionality: fully functional, machine/vehicle number: 180664, We are selling a Grazioli Dania 180-1000 lathe, manual operation. Year of manufacture: 1970. In good used condition. Isdpsx U Ac Refx Abrsan

Condition: used, Year of construction: 2012, functionality: fully functional, machine/vehicle number: G3169-0110, turning length: 530 mm, turning diameter: 420 mm, spindle speed (min.): 20 rpm, spindle speed (max.): 4,000 rpm, spindle bore: 65 mm, travel distance X-axis: 220 mm, travel distance Y-axis: 80 mm, travel distance Z-axis: 550 mm, overall weight: 4,700 kg, turning diameter over bed slide: 800 mm, HYUNDAI WIA L200SY CNC TURNING CENTER Year: 2012 | Fanuc 18i-TB CNC Control SN: G3169-0110 • 5-Axis CNC Turning Center – Hyundai WIA L200SY • Main Chuck: 8″ | Sub Spindle: 5″ • Live Tooling & Y-Axis + C-Axis indexing • Max Turning Diameter: approx. 419–420 mm / 16.5″ • Max Turning Length: approx. 520–530 mm / ~20.5–20.9″ • Swing Over Bed: approx. 800 mm / 31.5″ • X Travel: approx. 220 mm / 8.7″ • Z Travel: approx. 550 mm / 21.7″ • Y Travel: approx. 80 mm / 3.1″ • Max Spindle Speed: up to 4,000 rpm Iaedpfx Aox I A Hcsbrjn • Main Spindle Power: ~20 HP (~15 kW) • Sub Spindle Speed up to 6,000 rpm • C-Axis indexing: 0.001° possible • Tool Stations: approx. 12 • Coolant system and chip conveyor included • Approx. Dimensions: 120″ × 68″ × 80″ • Approx. Weight: ~10,500 lbs (~4,760 kg) NOTE: MACHINE WAS REMOVED FROM GOOD WORKING CONDITION 2 YEARS AGO. PLANNED TO PUT BACK IN SERVICE BUT SELLER WILL NO LONGER BE DOING MACHINING.

Condition: excellent (used), Broadbent Heavy Duty Lathe 1041mm x 10,000mm Year approx. 1973. Swing over bed 1041mm (41”) Iedewhylvopfx Abrsan Swing bin gap1575mm (62”) Distance between centres 9300mm (30’ 6”) Spindle bore 115m (4 ½”) Spindle speeds (18) 3.3 – 360 rpm Spindle motor 30 HP or 40 HP (To be confirmed) Tailstock 6 MT Imperial & Metric screw-cutting with change gears. 36” Faceplate with 4 adjustable jaws, 54” Faceplate, Taper turning attachment, Power feed to top slide, 2 x 18” 3 point steadies, 24”/28” Steady.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Schiess CNC vertical lathe with C axis, year 1992, retrofitted in 2012 CNC: NUM 1060 FLEXIUM 2 tables, table diameter 2000mm – max turning diameter 2500mm – max table speed 201 rpm – table power 56 KW Load capacity (table included): 16,000kg Iasdjxpqm Repfx Abren Movable crossrail with 12 positions, 50mm pitch Available space under spindle nose: min. 795mm, max. 1345mm RAM Z stroke: 1000mm C axis with 360,000 positions – milling spindle max speed 1600 rpm – milling spindle power 22KW – 2 gear ranges Tool magazine: 20 turning tool positions, 35 milling tool positions 1 milling head WIDAFLEX UTS80 1 milling head ISO 50 Renishaw MP60 touch probe (for parts) Tool presetter – Transmit function: G20 / G21 – No rigid tapping Chip conveyor Front door: partial opening M0 / full opening

Condition: new, Year of construction: 2025, turning diameter over cross slide: 250 mm, turning length: 730 mm, turning diameter: 500 mm, spindle speed (max.): 1,800 rpm, CNC lathe machine CK 6150 with flat bed We offer a new CNC lathe machine model CK6150. Iaedpfsxdmgvox Abron We use this machine in our production and you can see it in operation before ordering. The CK 6150 lathe has a flat bed and hardening guides, which ensures a long period of operation of the equipment. The machine is equipped with a CNC system, the GSK CNC system is installed as standard. Optionally, the machine can be equipped with a Fanuc or Siemens CNC system. The machine can have a tool holder for 4-6 or 8 tools, depending on the customer's wishes. It is possible to install a hydraulic chuck on the machine, which will greatly simplify the process of installing parts on it and a hydraulic tailstock. The CK 6150 lathe can be equipped with additional supporting frame for more accurate manufacturing of long parts. Technical specifications: Model CK 6150 x 1000 Maximum workpiece diameter over bed 500 mm Maximum workpiece diameter over support 250 mm Maximum workpiece length 1000 mm Maximum turning length 730 mm Spindle bore diameter 82 mm Spindle speed 150-1800 rpm Engine power 7.5 kW Mechanical chuck (hydraulic optional) Chuck size 250 mm. 4-position tool holder (6 or 8 optional) Maximum tool size for tool holder 25x25 mm Machine weight 2700 kg Machine dimensions 2650×1700×1820 mm We can also supply lathes CK 6140, CK 6150 and CK 6160 with other dimensions of the working part: CK 6140 dimensions of the working part 550/750 mm CK 6150 dimensions of the working part 1000/1500/2000 mm CK 6160 dimensions of the working part 1000/1500/2000 mm CK 6152E dimensions of the working part 1000/1500/2000/3000 mm CK 6165E dimensions of the working part 1000/1500/2000/3000 mm CK 6165E dimensions of the working part 1000/1500/2000/3000 mm CK 6185E dimensions of the working part 1000/1500/2000/3000/4000 mm CK 61100E dimensions of the working part 1000/1500/2000/3000 mm CK 61125E dimensions of the working part 1000/1500/2000/3000 mm

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, spindle speed (max.): 3,500 rpm, travel distance X-axis: 271 mm, travel distance Y-axis: 600 mm, center width: 600 mm, Equipment: bar feeder, chip conveyor, TECHNICAL DETAILS Swing diameter over bed: 350 mm Distance between centers: 600 mm Bed width: 210 mm Travel X-axis: 271 mm Travel Y-axis: 600 mm Spindle bore: 62 mm Max. spindle speed: 3,500 rpm MACHINE DETAILS CNC control manufacturer: Siemens Power: 30.0 kW Dimensions & Weight Dimensions (L x W x H): 4,300 x 2,100 x 2,100 mm Unladen weight: 5,000 kg Transport weight: 5,000 kg EQUIPMENT Chip conveyor Three-jaw chuck Isdpfoyh Npmex Abrsan Bar feeder Driven tools C-axis

Condition: ready for operation (used), functionality: fully functional, turning diameter over bed slide: 630 mm, center height: 315 mm, center width: 8,000 mm, spindle speed (max.): 1,180 rpm, empty load weight: 9,000 kg, TECHNICAL DETAILS Centre height: 315 mm Centre distance: 8,000 mm Swing diameter over bed: 630 mm Swing diameter over cross slide: 360 mm Bed width: 700 mm Spindle bore: 62 mm Max. spindle speed: 1,180 rpm MACHINE DETAILS Iaodpfx Abjyh Nk Rjrsn Control: Conventional Connected load: 22.0 kW Dimensions & Weight Dimensions (L x W x H): 10,560 x 1,710 x 1,400 mm Unladen weight: 9,000 kg EQUIPMENT Digital readout

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: F20170X00187, Year of construction: 2020, operating hours: 5,557 h, load capacity: 2,000 kg, overall weight: 774 kg, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Load capacity: 2,000 kg MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 700 x 1,145 x 1,850 mm Weight with battery: 774 kg Operating hours: approx. 5,557 h Drive power: 1.2 kW Iaodpfx Ajyhdf Ssbron EQUIPMENT Charger

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: F20170X00184, Year of construction: 2020, operating hours: 2,302 h, load capacity: 2,000 kg, overall weight: 774 kg, total length: 700 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Iaodjyhddbopfx Abren Load capacity: 2,000 kg MACHINE DETAILS Dimensions & weight Dimensions (L x W x H): 700 x 1,145 x 1,850 mm Weight with battery: 774 kg Operating hours: approx. 2,302 h EQUIPMENT Charger

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2019, operating hours: 7,866 h, load capacity: 2,000 kg, lifting height: 130 mm, fork length: 1,000 mm, overall weight: 866 kg, TECHNICAL DETAILS Load capacity: 2,000 kg Load center distance: 600 mm Load distance: 1,023 mm Lift: 130 mm Fork inner dimensions: 55 / 172 / 190 mm Fork outside distance: 560 mm Fork length: 1,000 mm MACHINE DETAILS Tyres: Polyurethane + Drive wheel size: 230 x 75 mm Load wheel size: 2 x 85 x 80 mm Support rollers (drive side): 140 x 54 mm Track width (drive side): 495 mm Track width (load side): 388 mm Travel speed with load: 7.5 km/h Travel speed without load: 9.0 km/h Lifting speed with load: 1.4 m/s Lifting speed without load: 1.4 m/s Lowering speed with load: 0.9 m/s Lowering speed without load: 1.2 m/s Gradeability with load: 10 % Gradeability without load: 20 % Acceleration time over 10 m with load: 6.9 s Acceleration time over 10 m without load: 5.4 s Service brake: electromagnetic Dimensions & Weight Dimensions (L x W x H): 2,333 x 720 x 1,305 mm Weight: 866 kg Battery voltage: 24 V Rated capacity: 240 / 360 Ah Battery weight ± 5%: 220 / 290 kg Operating hours: approx. 7,866 h Iasdpfxeyianco Abrjn EQUIPMENT Integrated charger Display with charge level and operating hours

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: W42377N00009, Year of construction: 2024, operating hours: 8 h, load capacity: 800 kg, mast type: triplex, fork length: 1,500 mm, overall weight: 1,995 kg, Stacker with only 8 operating hours! TECHNICAL DETAILS Load capacity: 800 kg Fork length: 1,500 mm Lift height: 2,800 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 2,200 x 820 x 2,260 mm Weight: 1,995 kg Mast type: Triplex Battery voltage / capacity: 24 V / 500 Ah Operating hours: approx. 7.3 h EQUIPMENT Charger Hydraulic carton clamps Side clamps (1,150 mm length) Operating manual (digital in PDF format) Iasdeyh E Ekjpfx Abrjn

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 98306821, Year of construction: 2021, operating hours: 12,312 h, load capacity: 2,500 kg, fork length: 860 mm, TECHNICAL DETAILS Load capacity: 2,500 kg Fork length: 860 mm Load center distance: 575 mm MACHINE DETAILS Battery voltage/capacity: 24 V / 390 Ah Iasdjyh Du Depfx Abrjn Operating hours: approx. 12,312 h EQUIPMENT Charger Digital display Code card for starting Note: The digital display has lines.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2021, operating hours: 12,312 h, load capacity: 2,500 kg, fork length: 2,400 mm, TECHNICAL DETAILS Load capacity: 2,500 kg Isdpfjyh A I Nex Abrsan Fork length: 2,400 mm Load centre distance: 1,200 mm MACHINE DETAILS Unladen weight without battery: 652 kg Battery voltage: 24 V Battery capacity: 390 Ah Operating hours: approx. 12,312 h EQUIPMENT Charger Digital display Operating hours indicator Charge status display Code card for starting Note: The digital display has stripes.

Condition: ready for operation (used), Year of construction: 2015, operating hours: 16,000 h, functionality: fully functional, turning length: 80 mm, spindle speed (max.): 7,000 rpm, bar diameter (max.): 32 mm, controller model: Fanuc Serie 32i-B, TECHNICAL DETAILS Maximum bar diameter: 32 mm Maximum turning length: 80 mm Main spindle speed: 7,000 rpm C-axis (main spindle): 0.001° Maximum counter spindle diameter: 32 mm Counter spindle speed: 7,000 rpm Tool capacity: 23 tools MACHINE DETAILS Control system: Fanuc Series 32i-B Number of axes: 7 Operating hours: 16,000 h EQUIPMENT Coolant pump with increased delivery capacity Parts conveyor belt Iasdpfx Asyh Azpebren Mayfran chip conveyor Service kit with emulsion package Bar feeder FMB Turbo 3-36/3200 / A Emulsion coolant unit Accessories for short lathe subframe Note: The seller can offer disassembly and loading for €2,000.

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: G00399, turning length: 2,000 mm, turning diameter: 560 mm, spindle bore: 82 mm, spindle speed (max.): 2,200 rpm, controller model: FANUC Series oi-TC CNC, TECHNICAL DETAILS Isdpfx Asygxipobrsan Turning diameter: 560 mm Turning length: 2,000 mm Spindle speeds: 2,200 rpm Spindle bore: 82 mm Tailstock quill taper: MK 5 Quill stroke: 150 mm MACHINE DETAILS Control: FANUC Series oi-TC CNC Total power requirement: 7.5 kW Dimensions & weight Space requirement: approx. 3,800 x 1,750 x 1,600 mm Machine weight: approx. 3,800 kg EQUIPMENT 3-jaw chuck 250 mm 6-position tool turret Coolant system Automatic pressure lubrication 1x travelling steady rest 1x fixed steady rest 2x machine lights

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: 09071204, turning length: 1,000 mm, turning diameter: 430 mm, spindle speed (max.): 2,800 rpm, travel distance X-axis: 240 mm, travel distance Z-axis: 700 mm, TECHNICAL DETAILS Turning diameter: 430 mm Turning length: 1,000 mm Turning diameter over cross slide: 277 mm Spindle bore: 30 mm Spindle speed range: 30 - 2,800 rpm X-axis travel: 240 mm Z-axis travel: 700 mm MACHINE DETAILS Control: CNC Ijdpfxjygxhxo Abroan Total power requirement: 10 kW Dimensions & Weight Required floor space: approx. 2,500 x 1,900 x 1,900 mm Machine weight: approx. 3,000 kg EQUIPMENT 3-jaw chuck 200 mm 4-position tool holder Coolant system Machine lamp

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: X1T126, spindle bore: 42 mm, turning length: 650 mm, turning diameter: 350 mm, spindle speed (max.): 3,500 rpm, controller manufacturer: Fanuc, TECHNICAL DETAILS Max. turning length: 650 mm Max. turning diameter: 350 mm Spindle bore: 42 mm Max. spindle speed: 3,500 rpm MACHINE DETAILS Control system: Fanuc Dimensions & Weight Dimensions (L x W x H): 2,400 x 1,700 x 1,500 mm Weight: 1,800 kg EQUIPMENT 3-jaw chuck Multiple jaws Collet chuck Iasdjyg Hvwjpfx Abren Collets Steady rest Faceplate Parat tool holder

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2019, operating hours: 7,866 h, load capacity: 2,000 kg, lifting height: 130 mm, fork length: 1,000 mm, overall weight: 850 kg, TECHNICAL DETAILS Load capacity: 2,000 kg Load center distance: 600 mm Load distance: 1,023 mm Lift height: 130 mm Fork length: 1,000 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 2,333 x 720 x 1,305 mm Weight: 850 kg Battery Voltage / Capacity: 24 V Version: Pedestrian-operated or rider Tyres Tyres: Polyurethane Drive wheel size: 230 x 75 mm Load wheel size: 2 x 85 x 80 mm Support rollers (drive side): 140 x 54 mm Number of wheels drive/load side: 1 x – 2 / 4 Track width drive side: 495 mm Ijdpfxjyh Hlfo Abroan Track width load side: 388 mm Operating hours: approx. 7,866 h EQUIPMENT Charger (integrated) UVV: 11/26 Display for battery charge status and operating hours Note: The battery tray is dirty.

Condition: ready for operation (used), functionality: fully functional, load capacity: 1,600 kg, lifting height: 122 mm, overall weight: 420 kg, TECHNICAL DETAILS Load capacity: 1,600 kg Load center distance: 600 mm Load distance: 908 mm Wheelbase: 1,252 mm Lift height: 122 mm Length incl. fork back: 486 mm Fork dimensions: 55 x 172 x 1,150 mm Outside fork width: 535 mm Ground clearance at wheelbase center: 30 mm Working aisle width for pallet 1,000 x 1,200 transverse: 2,240 mm Working aisle width for pallet 800 x 1,200 lengthwise: 2,128 mm Turning radius: 1,433 mm Isdoyh D Idopfx Abrean Axle load with load front/rear: 695 / 1,325 kg Axle load without load front/rear: 331 / 89 kg MACHINE DETAILS Dimensions & Weight Dimensions: 1,636 x 720 mm Tiller handle height: min. 750 / 1,237 mm Lowered height: 85 mm Weight: 420 kg Battery voltage/capacity: 24 V / 390 Ah Operating hours: approx. 9,201 h EQUIPMENT integrated charger

Condition: excellent (used), Year of construction: 2019, operating hours: 13,000 h, functionality: fully functional, bar diameter (max.): 22 mm, INDEX MS22-8 Ijdpfx Abex H H Nrjroan Mfd. 2019 2 NCU 2 Syncrons 2 Y-Axis Control: Siemens Solution Line Knoll System Bar Feed: IEMCA SIR rack loader (12-ft) 22,000 on-hours 10,000-15,000 Hours

Condition: excellent (used), Year of construction: 2004, operating hours: 1,000 h, functionality: fully functional, turning diameter over cross slide: 380 mm, turning length: 350 mm, turning diameter: 200 mm, travel distance X-axis: 240 mm, rapid traverse X-axis: 12 m/min, Hembrug Mill-Turn Machine Model: Slantbed Mikroturn 100 CNC Siemens 840D Control Approximate Actual Run Time Hours: 1,000 Hydeostatic Spindle Hydrostatic Ways Scale Feedback Suspended Granite Bed Garnite Spindle Housing Coolant Pump Coolant Circulation Pump Pneumatic Bearing Purge Hydraulic Temperature Control Coolant Temperature Control Return Oil Pump and Reservoir for Remote Location of Hydraulic / Cooling Unit. Options & Additional Purchased Features: Tailstock Iaedpfx Abewcfgberon Vacuum Pump for Vacuum Chucking Programable Controlled Spray Mist C-Axis Milling / Drilling Renishaw Tool Touch Probe Non-Contact Tool Incoming Air Dryer / Filter Thousands of Dollars of Brand New Tooling: Live Center Tailstock Taper Adapter 8” Micro-Centric Pneumatic Chuck 3 Sauter Straight Live tooling heads 2 Sauter 90 degree Live tooling heads 1 Special VDI offset Tooling holder 16 VDI Tool Holders for Turning, boring, and on center drilling. Tool Pick-up Video System Additional Backup Hard Drive with Software Fully Loaded and Tested. Extra Siemens Control Pannel Complete Set of Manuals Machine Upgrades I added at additional cost. New Digital Hard Drive New Backup Hard Drive with software already loaded, plug and play ready, no downtime. New Z-Axis Heidenhain Scale Rewound Hydraulic Pump Motor, factory motor was running too hot for my liking. Replaced Operator Panel, back light on monitor went out, have the original, back light needs replacing. 50 Foot Extended Wiring Harness For Remote Location of Hydraulic / Cooling Unit.