Used Pneumatic Feeder for sale (9,427)

Condition: used, Vibratory Feeder with Pneumatic Screwdriver Stand Eco Line Vibratory Feeder, Sorting Device, Bowl Feeder, Vibratory Bowl, Automatic Screwdriver WEBER Type ZSU 24 Machine No.: 1113212 Year of Manufacture: 2003 Vibratory Feeder WEBER ZSU 24 Bowl diameter: 240 mm Bowl internal height: 70 mm Sorting track width: 10 mm Power supply: 230 Volt, 50 Hz Operating pressure: 6 bar (for singulation and screws) Control voltage for pneumatic valves: 24 Volt - Controller for infinitely variable vibration speed = infinitely variable transport speed - Vibratory bowl in protective enclosure - With pneumatic feeding system - Feed impulse via external electrical control - The feeder was used for feeding screws M5 x 12 mm - Some pneumatic hoses need to be replaced - Siemens S7-200 CPU 224 PLC MISSING Space requirements vibratory bowl L x W x H: 450 x 450 x 315 mm Dodpfx Ajxf Up Ujgcswf Vibratory bowl weight: 32 kg WEVER Eco Line Screwdriver Stand Guide column: Ø 60 x 525 mm Height adjustment: 345 mm Primary stroke pneumatic cylinder 1 FESTO DZF-32-125-P-A-SM: 115 mm Screwdriver holder diameter: Ø 50 mm Secondary stroke pneumatic cylinder 2 FESTO: 30 mm Screwdriver guide diameter: Ø 37 mm Distance screwdriver guide to table: 135 - 465 mm - 1 piece flat cylinder FESTO, Type DZF-32-125-P-A-SM - 1 piece flat cylinder FESTO, Type probably DZF-32-30-P-A-SM - Screwdriver linear motion frame on linear guide - 3 position sensors on the cylinders - Festo pressure switch - Bosch pneumatic valve Screwdriver stand dimensions W x D x H: 200 x 410 x 1050 mm Screwdriver stand weight: 35 kg good condition Total weight vibratory feeder and screwdriver stand: 67 kg Attention: The original Siemens S7-200 CPU 224 PLC is missing (see picture control cabinet without PLC), therefore, an automatic process is not possible in this condition. The control system also managed the separations of the screws and controlled the screwdriver itself. The vibratory bowl is fully functional even without the PLC, the built-in vibratory bowl controller does not require PLC control. Process: Fasteners are filled into the bowl in bulk and conveyed upward by mechanical vibration (micro-throw principle). The vibratory bowl is automatically switched on or off depending on the fill level of the screw magazine. The screw is then conveyed by compressed air through a plastic hose to the downstream device. The feed impulse for each individual screw is triggered externally by the downstream device.

Condition: excellent (used), Pamasol 33200 Pneumatic feeder With 1-lane exit onto the conveyor belt Dwsdsqazqiepfx Agcsf Accumulation conveyors ensure an even product feed to a processing machine. - Hinged belt chain 150 mm wide - 8-lane, with 1-lane exit - Drive with infinitely variable geared motor - Without center belt drive - Suitable for continuous operation in hazardous areas - Electric drive unit - Feed table suitable for Centomat Specifications Capacity: Up to 3000 cans per day The capacity depends on the can size, filling volume, valve type and number of workers Cans: Ø 100-200 mm x H 50-200 mm, aluminum, tinplate and glass Electrical connection: 3 x 400 V + N + PE, 50 Hz Dimensions: H x W x L 88 x 140 x 290 cm New price 57.000 ,-€ You can find more items - new and used - in our store! International shipping costs on request!

Condition: excellent (used), Pamasol 5934 Pneumatic feeder With 1-lane exit onto the conveyor belt Accumulation conveyors ensure an even product feed to a processing machine. - Hinged belt chain 150 mm wide Dwsdpfjqazcyjx Agcsf - 5-lane, with 1-lane exit - Drive with infinitely variable geared motor - Suitable for continuous operation in hazardous areas - Electric drive unit Electrical connection: 3 x 400 V + N + PE, 50 Hz Dimensions: H x W x L 88 x 80 x 210 cm Further items in other sizes - new and used - can be found in our store! International shipping costs on request!

Condition: used, Year of construction: 2015, functionality: fully functional, overall weight: 880 kg, Specification: Protection rating: IP54 Control voltage: 24V DC Fuse: 16A Power: 0.5kW The hydropneumatic press with feeder from Tox Pressotechnik is a versatile and efficient solution for the precise and reliable processing of a wide range of materials. By combining hydraulic power and pneumatic control, it allows for uniform force transmission as well as fast and controlled operation. The integrated feeder ensures a smooth material flow, increasing productivity and optimizing the production process. Dwodpfx Aowq R Rhogcof

Condition: used, The Wahli-Stream Feeder TM 530 is a reliable feeder designed for efficient paper handling. Manufactured by Wahli, this model is located in Germany, with pricing available upon request. The machine supports an A2 format and is designed to enhance productivity in printing and finishing operations. Format: 360 420 mm Equipment: AUTOMATIC ENVELOPE FEEDER (with vacuum suction) SUITABLE FOR PRESSES WITH STREAM / SINGLE SHEET FEEDERS Dwodpfx Aevphzpsgcjf ADJUSTABLE VACUUM, HEIGHT & SPEEDDELIVERY CONVEYOR MIN ENVELOPE SIZE: 7.6 x 12.7 CM MAX ENVELOPE SIZE: 36 x 42 CM

Condition: excellent (used), Machine in very good condition. It has worked to the end, now it is on warehouse not connected to power. Machine in 100% completed Dwodovllbrjpfx Agcef Hu3Nhjg Parts conveyor, chips conveyor, bar feeder available. Spindels bore 42 mm IRCO feeder bar All manuals and documentation available

Condition: excellent (used), machine/vehicle number: 41206972, WITH DELIVERY BELT Return belts For 10.5 cm x 14.8 cm envelopes and portrait orientation, the straps should be pushed to the middle conveyor belt Rule: for large envelopes, push the straps out, for small envelopes press the straps (22) inwards. CONNECTION TO PRINTING MACHINE The STENZ FEEDER does not need synchronization. The feeder is guided by the handles the pressure machine and sets the required height with the crank. Important: only when the printing height is set, fix the rear rollers and check the stability. Turn on the machine and start printing. For single sheet feeder printing machines (GTO) adjustable inclination. Efficient printing of envelopes can now begin. Dedpfsxuhy Sex Agcswf Designed for heavy-duty use at maximum printing speeds. Compatible with all 36 x 52 print machines irrespective of the feed system (overlapped/single-sheet feed). - Requires no mechanical alterations to the printing machine - No need for synchronization adjustments as controlled by laser technology - Very short set-up time allows economic use from 1000 envelops upwards - Easy to operate - The design of the feeder results in a forced overlap. The Stenz Feeder is thus not restricted in throughput - A minimum of wearing parts for extremely long service life - Already approved in thousands of different print machines - A Swiss quality product - Designed by printers for printers. Specifications: Speed: Limited by print machine Length: 115 cm Width: 50 cm Height: adjustable between Max. format size: 36.5 x 35 cm Max. pass-through width: 36.5 cm Electrical: 230 V, 50 Hz

Condition: ready for operation (used), functionality: fully functional, input voltage: 24 V, type of input current: DC, pressure: 7 bar, For sale: Complete Clyde Bergemann ash hopper assemblies (EPK-7A / EPK-7B), designed for industrial ash collection and pneumatic conveying systems. Each unit includes: Ash hopper throat with thermal insulation Clyde Bergemann double-acting pneumatic actuator (24 VDC / 7 bar) Control cabinet with gauge and automation elements Dwodpfxjxy Nt Ds Agcef Stainless steel ash discharge piping High-temperature insulation CE-marked, energy-sector quality components Systems are operational, complete, and were in service until decommissioning. Ideal for power plants, biomass plants, waste-to-energy facilities, or ESP ash handling retrofits.

Condition: reconditioned (used), Year of construction: 2013, overall weight: 447 kg, volume flow: 178.8 m³/h, pressure (max.): 13 bar, Equipment: type plate available, PROD - CHICAGO PNEUMATIC TYPE - CPVS40 S/N - CAI616722 YEAR - 2013 POWER (kW) - 30 EXPENDITURE. (m3/min) - 2.98 CIS (bar) - 13 Dwsdpforb A Nyox Agcjf WAVE - yes

Condition: new, functionality: fully functional, Year of construction: 2025, CONSTMACH vibrating feeder bunkers are high-efficiency equipment designed to ensure continuous and balanced feeding of crushers in stone crushing and screening plants. These bunkers are placed in front of primary impact crushers or jaw crushers to ensure a homogeneous flow of material. This increases the capacity of the crushers, balances the loads on the intermediate crushers, and ensures continuity in the overall production line. The vibrating feeding system prevents sudden loads, eliminating the risk of overloading on conveyor belts and thermal damage to equipment. Thanks to CONSTMACH's special design, the vibrations in the bunkers are smooth and balanced. This ensures both a steady material flow and extended machine life. Otherwise, uneven feeding could cause serious wear on crusher hammers, conveyor belts, and bearings. Using a vibrating feeder bunker helps reduce maintenance costs, increase operational efficiency, and maintain long-term performance throughout the facility. Vibrating Feeder Bunker Technical Specifications Model: CPG - 09 Body Size: 2,500 x 520 mm Grid Size: 820 mm Motor Power: 2 x 3 kW Bunker Volume: 8 - 10 - 15 m³ Capacity: 80 - 100 t/h Weight: 8,000 kg Model: CPG - 10 Body Size: 3,000 x 850 mm Grating Size: 1,160 mm Motor Power: 2 x 4.5 kW Hopper Capacity: 10 - 15 - 20 m³ Capacity: 150 - 200 t/h Weight: 12,000 kg Model: CPG - 11 Body Dimensions: 4,600 x 1,100 mm Grate Dimensions: 1,400 mm Motor Power: 2 x 9.2 kW Bunker Volume: 15 - 20 - 30 m³ Capacity: 200 - 300 t/h Weight: 18,000 kg Model: CPG - 13 Body Size: 4,880 x 1,370 mm Grating Size: 1,840 mm Motor Power: 2 x 11 kW Dwjdpfx Agexqf Sdjcsf Bunker Volume: 30 - 45 - 50 m³ Capacity: 350 - 500 t/h Weight: 26,000 kg Why Choose CONSTMACH Vibrating Feeder Bunkers? CONSTMACH is a trusted brand in the industry with years of engineering experience and high production standards. Our products stand out with their durable body structure, low maintenance requirements, and energy-efficient motor systems. Each one undergoes high-quality control processes to ensure long-lasting use. CONSTMACH Vibrating Feeders increase the performance of your crushing plant while minimizing your operating costs. If you are looking for quality, durability, and maximum efficiency, CONSTMACH is the right solution. What Do We Do at Constmach? Constmach is a leading machine manufacturer serving the construction and mining industries with a wide range of products. Our product portfolio includes concrete block making machines, stationary and mobile concrete plants, stone crushing machines, stone crushing and screening plants, sand washing machines, sand making machines, asphalt plants, conveyor belt systems, jaw crushers, and mobile crushing plants. With its high quality standards, innovative production approach, and customer-focused solutions, Constmach stands out as a reliable brand in both national and international markets. Our products continue to be the preferred choice of industry professionals due to their durability, efficiency, and long-lasting performance.

Year of construction: 2005, condition: excellent (used), diameter: 1700mm Dedpefd E R Aofx Agcswf Stainless steel

Condition: new, Year of construction: 2025, operating hours: 1 h, machine/vehicle number: 6151710200, Demo tool with only 2 operating hours: Chicago Pneumatic CP4210AS push riveting machine with short alligator head Take advantage of the CP push riveting tool for the most common riveting and repair applications for metal structures in the aerospace industry. Experience the benefits of the CP push riveting tool for the most common riveting and repair applications for metal structures in the aerospace industry. Year of manufacture: 2025 Technical specifications: Max. compression force (90 psi/6.2 bar): 13.3 kN Max. piston stroke: 15.9 mm Dedpfx Aoxwu Rcegcjwf Height: 92 mm Length: 233 mm Weight: 1.7 kg Jaw type: Alligator short Main material: Aluminum Max. rivet size aluminum (in): 1/8 Max. rivet size aluminum (mm): 3.2 Max. rivet size steel (in): 3/32 Max. rivet size steel (mm): 2.4 Starting system: Safety lever Air inlet thread size (in): 1/4 Air inlet thread size: NPT Max. working air pressure: 6.3 bar Min. hose diameter (5 m hose length): 0.38 in Min. hose diameter (5 m hose length): 9.5 mm Visit our store; we always have a wide selection of Pneumatic tools for industry and trade in stock.

Year of construction: 2003, condition: excellent (used), Feeder Caps 8006 automatic disc feeder, sorting machine Fully automated, variable dosing speed, manual height adjustment. Stainless. Year of production: 2003 Power: 0.55kW max. dosing capacity: approx. 1000 pcs / min Diameter: 1400mm Siemens control. Djdpfsg Rkwmsx Agcjwf Purchase of industrial equipment and machinery. Wide Range of Used Machinery, Industrial Equipment

Condition: new, Year of construction: 2025, PROFESSIONAL WIRE FEEDER WITH AC SERVO MOTOR FOR LASER AND TIG WELDING Citronix professional wire feeder with servo technology - means that it uses ac servo motor for motor drive, which enables it not only to feed wire very precisely even when the speed is low, but also the ability to set the length in „mm“ for wire withdrawal, and also, after the material is cooled down, we can push it again (the smallest step 0,1 mm) This is a very important feat with laser welding, and this working method is an advantage compared to wire feeders made in the Far East, since with those machines the function of withdrawal and pushing the wire is set on time, and the consequence of this method is that the tip of the welding wire never comes back to the place where the withdrawal started. We made the Citronix wire feeder in a way that it can control not only the wire feeding process, but it can also manage (turn on and off) both the laser source and the gas magnetic valve. This is another significant difference and advantage compared to other manufacturers, because usually there is no spot welding technology in laser welding machines, so if someone wants to weld sheets in the spot welding technology, he can set the spot time and the wire feeder will control the laser source. Wire feeder has 4 operation technologies: 1. continuous welding with wire feeding; 2. continuous welding without wire feeding; 3. spot welding without wire feeding; Dodpfx Agomk S Slscowf Wire feeder has 200 memory cells – locations, if the parameters are set, they can be saved on the memory location and we can name them in any number or text combination, in order to make use easier. We also developed a foot pedal, which can be attached to the wire feeder and regulate the feeding speed. It works like a gas pedal in motor vehicles. If, for example, we set the maximal speed 10 meter per minute on the display, and press the pedal all the way, the speed will be 10 meter per minute (or the speed we set), if pressed only half way, the speed will be half of the set speed. This feat can be used if the operator remains in one place, for example if he is sitting. If this pedal isn't necessary, the wire feeder can be attached to the system in a manner to turn on-off the welding process from the button on the torch. This pedal is optional, and in case you want to order it, it is additionally charged 400 EUR. Take a look at the monitor images and see the functions – parameters that can be adjusted. Citronix wire feeder can be used not only for laser welding, but also for the TIG welding, we made a filter to prevent HF-spark. Wire thickness it can push is from 0,8-2,4 mm. At this moment, we have a menu in English, German, Hungarian, and Serbian language.

Condition: new, New Conveyor with overhead feeder hopper Both units are mobile on castors Feeder hopper with opening end door, adjustable exit gate to conveyor Feeder hopper dimensions 800mm x 740mm x 600mm deep Conveyor belt dimensions 1800mm x 230mm W x 1260mm H Dsdswd Nthjpfx Agcjwf Conveyor height is adjustable VFD on conveyor drive

Condition: new, functionality: fully functional, Year of construction: 2025, The wobbler feeder is a feeding system that delivers superior performance, especially when handling large, sticky, and moist materials. Its structure, consisting of rotating elliptical rods, creates a vibrating motion during material flow. This motion separates fine materials from larger particles and provides consistent feeding to crushers and screens. As a result, clogging is prevented and the overall efficiency of the plant is increased. Widely used in the mining, aggregate, and recycling industries, wobbler feeders are typically placed in front of primary crushers. This ensures that the material undergoes pre-screening in the initial stage. Its ability to operate without clogging, even with sticky and clayey materials, makes it an ideal solution for demanding conditions. Its mechanically simple design, ease of maintenance, and long-lasting performance keep operating costs to a minimum. With these features, wobbler feeders are a reliable choice for all plants requiring a continuous and balanced material flow. Wobbler Feeder Technical Specifications Body Liners: HARDOX 450 – 10 mm Dedpoxqcn Asfx Agcowf Feeding Capacity: 150 - 200 t/h Weight: 18.5 tons Dimensions: 4,000 x 1,000 mm Wobbler Motor: 14 x 3 kW, 1500 rpm, GAMAK brand Gearbox: Heavy-duty type Walking Platforms: Available Steel Feet: Available Why Choose CONSTMACH Wobbler Feeders? CONSTMACH wobbler feeders stand out with their high-quality, durable materials, heavy-duty gearboxes, and ease of maintenance. Each one is designed to offer long-lasting, low-cost operation. HARDOX body liners provide maximum resistance to wear, while the adjustable design easily adapts to different material types. CONSTMACH is a trusted name in the industry for its production quality, engineering support, and after-sales service. Invest in a wobbler feeder with the CONSTMACH guarantee for the continuity and performance of your facility. What Do We Do at Constmach? Constmach is a leading machine manufacturer offering a wide range of products designed to meet the needs of the construction and mining industries. Our product portfolio includes concrete block making machines, stationary and mobile concrete plants, stone crushing machines, stone crushing and screening plants, sand washing machines, sand making machines, asphalt plants, conveyor belt systems, jaw crushers, and mobile crushing plants. With its high quality standards, innovative production approach, and customer-focused solutions, Constmach stands out as a reliable brand in both national and international markets. Our products continue to be the preferred choice of industry professionals due to their durability, efficiency, and long-lasting performance.

Condition: excellent (used), Volt: 220-240VAC // Amps. 1.8 // Hz: 50/60 // Ph: 1 // Kw: 0.4 WITH DELIVERY BELT Return belts For 10.5 cm x 14.8 cm envelopes and portrait orientation, the straps should be pushed to the middle conveyor belt Rule: for large envelopes, push the straps out, for small envelopes press the straps (22) inwards. CONNECTION TO PRINTING MACHINE The STENZ FEEDER does not need synchronization. The feeder is guided by the handles the pressure machine and sets the required height with the crank. Important: only when the printing height is set, fix the rear rollers and check the stability. Turn on the machine and start printing. For single sheet feeder printing machines (GTO) adjustable inclination. Efficient printing of envelopes can now begin. Designed for heavy-duty use at maximum printing speeds. Compatible with all 36 x 52 print machines irrespective of the feed system (overlapped/single-sheet feed). - Requires no mechanical alterations to the printing machine - No need for synchronization adjustments as controlled by laser technology - Very short set-up time allows economic use from 1000 envelops upwards - Easy to operate - The design of the feeder results in a forced overlap. The Stenz Feeder is thus not restricted in throughput - A minimum of wearing parts for extremely long service life - Already approved in thousands of different print machines - A Swiss quality product - Designed by printers for printers. Specifications: Speed: Limited by print machine Length: 115 cm Width: 50 cm Height: adjustable between Djdpfoh Eibaox Agcewf Max. format size: 36.5 x 35 cm Max. pass-through width: 36.5 cm Electrical: 230 V, 50 Hz

Condition: like new (used), functionality: fully functional, Year of construction: 2024, machine/vehicle number: 6151740170, Exhibit: Chicago Pneumatic Air Chisel Hammer GV 5 Strokes per minute: 2400 Dsdsxwpitepfx Agcewf Stroke: 52.5 mm Chisel shank: Hexagonal 19 mm Air consumption under load: 8.3 l/s Power: 12.2 Joules Weight: 5.1 kg Overall length: 385 mm Air inlet: G 1/2 Specifically designed for heavy-duty industrial applications, the GV5 hammer combines powerful blows and an efficient impact frequency with a robust design. Thanks to its metal housing, large stroke volume, and high impact rate, the GV5 offers maximum performance and durability simultaneously. It is therefore ideal for roughening, chiseling, or cutting tasks.

Condition: new, Year of construction: 2025, C43 airend Motor power 5.5 kW Pressure 8 bar FAD 888 l/min – 53 m3/h Power supply 400 V – three-phase -50 Hz Start YD Noise level 66 dB Connections 3/4″ Dedpjvpgclofx Agcjwf

Condition: used, Year of construction: 2014, power capacity 3 kW feed pressure 7 bar liter capacity / l weight 286 kg Chicago Pneumatic CPVR15 CE screw compressor - Year of manufacture 2014 The CPVR15 CE impresses with its robust design, long service life and low operating costs. Whether in workshops, workshops or industrial applications - this compressor reliably supplies you with the compressed air you need. Drive power: 3 kW Delivery pressure: 7 bar Air output: up to 58 CFM (approx. 1,640 l/min) at 7 bar Weight: 286 kg Dimensions: approx. 965 mm (L) × 620 mm (W) × 1,040 mm (H) Operating noise: approx. 50-58 dB(A) Voltage/frequency: 415 V / 50 Hz Application: Workshops, craft businesses, industrial applications with medium compressed air requirements Included in delivery: 1x compressor - Chicago Pneumatic CPVR15 CE 1x refrigeration dryer - OMI ESD 108 - 0.70kW 1x Beko Öwamat 2 - oil-water separator Dwedpfx Ajh A Sfdogcsf Technical data was taken from publicly available sources

Condition: ready for operation (used), functionality: fully functional, A good used Hopper Feeder fopr feeding small parts into assembly machine or feeding a bowl feeder with bulk parts - stainless steel conveyor - flighted belt (comes with a second spare belt also) - three phase geared drive unit - 24 V DC sensors (2) for control of belt index if required Ready to ship worldwide More pictures and videos available upon request Djdpfx Agow D Ev Eocswf

Condition: new, functionality: fully functional, color: yellow, Year of construction: 2025, • The Fabo Wobbler feeders are designed to feed sticky, wet and large materials comfortably and clean to the crusher with an ellipse-shaped bar and unique motion mechanism. With its self-cleaning structure, it eliminates the problem of obstruction and stone compression. • Work with wet and sticky materials without clogging and jamming. • Adjustable feed rate. • It occupies less space and has smaller height. • It works without dust, vibration and noise. • Low power consumption and maintenance frequency. • Width: 1400 mm • Length: 2500 mm • Motor power: 22 kW Dodpfxsxl R D Us Agcowf • Bar number: 5-9 • Elliptical bar shape • Aperture: 25-150 mm • Feeding size 50-1.500 mm • Chainy drive system • Max. Capacity 200-300 T / s • Capacities calculated according to the specified material density (1.6 tn/m3)

Condition: excellent (used), machine/vehicle number: 2069056, Equipment / Additional information: WITH DELIVERY BELT Return belts For 10.5 cm x 14.8 cm envelopes and portrait orientation, the straps should be pushed to the middle conveyor belt Rule: for large envelopes, push the straps out, for small envelopes press the straps (22) inwards. CONNECTION TO PRINTING MACHINE The STENZ FEEDER does not need synchronization. The feeder is guided by the handles the pressure machine and sets the required height with the crank. Important: only when the printing height is set, fix the rear rollers and check the stability. Turn on the machine and start printing. For single sheet feeder printing machines (GTO) adjustable inclination. Efficient printing of envelopes can now begin. Designed for heavy-duty use at maximum printing speeds. Dedpfjw Rvu Dox Agcewf Compatible with all 36 x 52 print machines irrespective of the feed system (overlapped/single-sheet feed). - Requires no mechanical alterations to the printing machine - No need for synchronization adjustments as controlled by laser technology - Very short set-up time allows economic use from 1000 envelops upwards - Easy to operate - The design of the feeder results in a forced overlap. The Stenz Feeder is thus not restricted in throughput - A minimum of wearing parts for extremely long service life - Already approved in thousands of different print machines - A Swiss quality product - Designed by printers for printers. Specifications: Speed: Limited by print machine Length: 115 cm Width: 50 cm Height: adjustable between Max. format size: 36.5 x 35 cm Max. pass-through width: 36.5 cm Electrical: 230 V, 50 Hz

Year of construction: 2024, condition: new, functionality: fully functional, machine/vehicle number: CP3T30-085AAV, Chicago Pneumatic Angle Turbine Grinder CP3T30-085AAV Dwedpfxoxwn R Ae Agcef with autobalancer with spindle lock Turbine grinder - twice the power with less weight! Ideal tool for grinding and smoothing cast iron, steel, welds, non-ferrous metals of all kinds and stones, e.g. in steel and container construction, mechanical engineering, foundries and reinforced concrete construction Specifications: Speed (idle): 8500 min-1 Max. power: 2.3 kW Air consumption under load: 1.92 m³/min Air consumption idle: 0.48 m³/min Weight: 2.1 kg Spindle Thread: M14 Air connection: IG 3/8" min. hose size at (5m hose length): 16 mm Required air quality: dried and oil-free

Condition: good (used), Short-stroke cylinder, pneumatic cylinder, air cylinder, pneumatic piston, air piston, standard cylinder -stroke: 50 mm -Piston: Ø 50 mm -Piston rod: Ø 16 mm -Number: 2x available -Price: per piece -Dimensions: 65/70/H95 mm Dwsdpsv Ab Hljfx Agcef -Weight: 0.65 kg