Used Profiling Machine for sale (67,410)

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Itsdpfjuz If Nox Ap Dsn Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Roundo PS340 3000 mm Hydraulic Double-Pinch Plate Bending Rolls Manufacturer: Roundo AB Model: PS340 Year: 1983 Country of manufacture: Sweden Type: Hydraulic three-roll double-pinch plate bending rolls Itjdpfx Apezuzpyj Dsn Capacity Maximum working length: 3,000 mm Pre-bending capacity: approximately 12 mm mild steel aximum rolling capacity: approximately 18–23 mm mild steel, depending upon finished diameter Standard upper-roll diameter: 340 mm Plate capacities based upon mild steel of approximately 270 N/mm² yield strength Minimum rolling diameter: approximately 1.1–1.4 times the upper-roll diameter, depending upon material thickness Remaining straight edge after pre-bending: approximately 1.5–2 times plate thickness Features Hydraulic double-pinch design Both lower rolls independently hydraulically adjustable Pre-bending of both ends without removing and reversing the plate Hydraulic rotation of all three rolls Infinitely variable rolling speed Hydraulic powered drop end Portable pendant control Front safety trip bar Heavy-duty fabricated and stress-relieved frame Forged and crowned steel rolls Rolls mounted in heavy-duty roller bearings Suitable for cylindrical and conical bending Approximate machine weight: 14,000–15,000 kg, subject to confirmation Approximate main motor: 22 kW, subject to data-plate confirmation

Year of construction: 2004, condition: good (used), functionality: fully functional, We have no more use from the machine and therefore its for sale. It is fully operational. The machine is in our ownership from 2007, regularly maintained and can be seen in our production hall in Croatia. Dismantile and load on truck are in price. Some other information: 4-axis profile machining centre Designed for flexible and efficient machining of aluminium Autonomous clamp positioning Max. working lenght: 7.200 mm 8 pneumatic clamps Tool magazine with 8 tools capacity Additional tehnical specifications available on request Itsdpjwwtxnofx Ap Djn

Condition: new, Year of construction: 2026, actuation type: electric, number of rollers: 3, shaft diameter: 30 mm, - Shaft diameter 30 mm - Can be operated in both clockwise and counterclockwise directions Isdpfezmc T Dox Ap Dstn - Suitable for horizontal and vertical applications - Foot pedal control - Emergency stop switch - Documentation - 400V

Condition: like new (used), Double-sided profiling milling and grinding machine, model Uinze 4T2500STD - Year of manufacture: 2023 - New price: €64,000 - Machine is equipped with 2 special carbide milling heads and 2 grinding units - Weight: 4300 kg - Safety fence: 800 kg, safety roller gate: 300 kg Iodpfxjzqgmcs Ap Dotn - Working length: 2500 mm, working width: 170 mm - Motor power: milling unit 4.5 kW, grinding unit 4.5 kW - Table return speed: 80-100 m/min - Milling speed: 4000 rpm

Condition: excellent (used), Year of construction: 1992, Shaft diameter: 40 mm Bending capacity: Flat bar edgewise at 500 mm Ø: 60 x 10 mm Flat bar flatwise at 400 mm Ø: 100 x 15 mm Square bar at 500 mm Ø: 35 mm Angle iron, leg outwards at 450 mm Ø: 50 x 50 x 6 mm Angle iron, leg inwards at 600 mm Ø: 50 x 50 x 6 mm T-section, T outwards/inwards at 600 mm Ø: 60 x 60 x 7/50 x 50 x 6 mm Round bar at 500 mm Ø: 35 mm Iodpfx Apjx Anpvj Dotn Shaft speed: 7.5 rpm Electrical connection: 380 V, approx. 1.7 kW Space requirement: 910 x 640 x 1400 mm Weight: approx. 480 kg

Condition: used, Dimensions (l x w x h) approx.: 3200 x 1800 x 1600 mm Weight approx.: 500 kg 3 spindles, 1 milling spindle, 2 - 3 grinding and milling spindles, feeder belt approx. 100 mm wide, total working length approx. 3000 mm, Itedpfxexrlgwo Ap Djn extendable workpiece support

Condition: used, 5-way combination profile steel shear, PEDDINGHAUS Type 210 AD/13 Machine No. 529A059, Year of manufacture approx. 1970 Punching unit: Punching force 60 tons Punch stroke 25.5 mm Punching capacity Ø 25 mm in 16 mm sheet metal Ø 20 mm in 19 mm sheet metal Overhang 365 mm Round bar shear: Cutting capacity, round 42 mm Square 38 x 38 mm Flat bar shear: Cutting capacity at shear angle 5° 150 x 13 mm or 200 x 10 mm Blade length 245 mm Profile steel shear: Shearing capacity, angle iron at 90° 110 x 10 mm Shearing capacity, angle iron at 45° 90 x 9 mm T-steel 110 x 10 mm Notching device: Rectangular notching up to 12 mm sheet metal Punch dimensions 85 x 50 mm Itodpei Duh Ijfx Ap Den Motor power 3 kW Mains connection 380 Volt, 50 Hz - Center-finding device via hand lever and centering device - Mechanical stroke release via hand lever - Flat bar shear equipped with 2° blade - Mechanical clamp on the profile steel shear, round bar shear and on the flat bar shear Space requirement L x W x H 1500 x 800 x 1900 mm Weight 2000 kg Good condition

Condition: new, 35 (600) mm 35 (900) mm L-beam 50 x 50 x 5 (800) mm T - beam - web outwards 60 x 7 (600) mm Axis diameter 50 mm work speed 4,5 m/min total power requirement 1,5 kW weight of the machine ca. 0,4 t dimensions of the machine ca. 1,1 x 0,8 x 1,5 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display Itjdpfx Aefv H Etep Den - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device

Condition: like new (used), Year of construction: 2026, operating hours: 8 h, functionality: fully functional, machine/vehicle number: SG202640, total length: 1,500 mm, power: 4 kW (5.44 HP), overall weight: 650 kg, total width: 800 mm, total height: 1,150 mm, input voltage: 380 V, warranty duration: 12 months, Pipe Shrinking, Profile Forming Machine SG40NC Itjdjyak Ikopfx Ap Dsn Machine Model: SG40NC Product Description: Microcomputer-controlled and hydraulically driven. Equipped with a mobile foot switch featuring three functions: automatic operation, emergency stop, and continuous emergency stop, ensuring high safety. Capable of multiple processing methods including tube Forming, tube expanding, tube end blunting, and bulging. Processed shapes include concave-convex joints, elongated, flat, square, flared, angled, V-shaped, open elbow, etc. Molds can be changed according to the user’s processed products. Mold replacement is simple and convenient, facilitating flexible production. The machine has a compact and sturdy structure, uses hydraulic power, operates stably with a high yield rate, minimal vibration, and low noise. It can perform tube end reduction, expansion, bulging, upsetting rib forming, and other shape forming processes. Suitable for processing various shapes at the connecting parts of pipe fittings (for insertion), automotive oil pipes, air ducts, water pipes, and air conditioning pipes. Maximum Tube Forming Capacity mm Ø40×2mm Maximum Tube Forming Length mm 100mm Motor Power kW 4 Weight kg 600

Year of construction: 2014, condition: good (used), The Elumatec SBZ 130 is a 3-axis profile machining center designed for efficient processing of aluminum, steel, and stainless steel profiles. All operations, such as milling, drilling, and threading, are performed on a stationary profile, which protects its surface. - Axes: 3-axis control, with a tool spindle as an additional axis. - Machining length (X-axis): 7200 mm - Travel (Y-axis): standard 485 mm (Vmax. 60 m/min) - Travel (Z-axis): standard 340 mm (Vmax. 60 m/min) - Spindle speed: standard 6000 rpm, optional high-speed spindle (18,000 rpm) - Spindle power: 5.5 kW - Tool magazine: integrated revolving tool head for 8 tools or 4 angled heads, ensuring short tool change times - Control: Windows operating system with eluCam software; 18.5" PC panel, with USB ports and network connection - Clamping system: automatic positioning of pneumatic clamps Ijdsyt H Uyepfx Ap Dstn - Compressed air supply: 7 bar MACHINE: Prepared tooling dedicated to PVC and steel processing: - Tool holders, - Reducer for steel processing, - Special tools with chip breakers, - Dedicated programs for processing door profiles. The head was replaced in 2025.

Condition: used, functionality: fully functional, Year of construction: 2013, Sahinler HPK 200 Hydaulic section and pipe bending machine Mil and Shaft Diameter: 200mm Tool and Roll Diameter: 900mm Working Speed: 2-5 m/min Motor Power: 30 kW Bending capacity x15x4 273x5.6 / 10000 mm Iedpew D Uqxsfx Ap Dstn Diameter biggest roll 9"x6,3 / 4000 mm Diameter top roll 650 mm Diameter upper roll 650 mm Roll capacity section - 3 200x200x18 / 5000 Shaft diameter 200 mm Top roll x15 with prebending min.120x120 / 3000 mm Voltage 3x400 V Working speed 2-5 m/min Power Power max. 30000 W Height 2300 mm Length 2400 mm Width 3400 mm Weight15000 kg

Condition: ready for operation (used), A profile and surface grinding machine RBW is available. Grinding quality class: 6, rotary table diameter: 800mm, grinding diameter: 800mm, max. workpiece height: 300mm, max. workpiece weight: 1000kg. Documentation available. An on-site inspection is possible. Iedpfoy Hk T Uex Ap Dotn

Condition: good (used), functionality: fully functional, Year of construction: 2007, machine/vehicle number: CA90H2 PIPE BENDING ROLL, shaft diameter: 90 mm, roller diameter: 260 mm, rotational speed (min.): 8 rpm, rotational speed (max.): 8 rpm, overall weight: 1,000 kg, total length: 1,260 mm, total width: 1,000 mm, total height: 1,260 mm, power: 3.68 kW (5.00 HP), input voltage: 380 V, type of input current: three-phase, operating speed: 8 mm/s, roll diameter: 260 mm, Equipment: documentation/manual, emergency stop, PROFILE BENDING ROLL SHAFTS OUTPUT 90 MM - PIPE BENDING ROLL MARGI CA90H2 YEAR 2007 Iedpfowkrr Tox Ap Dotn SHATS OUTPUT SIZE 90 MM SET OF UNIVERSAL ROLLERS SIZE 260 MM LATERAL CORRECTOR ROLLERS LEFT/RIGHT SIDE SCREW ADJUST 4 SET OF ROLLERS FOR TUBE BENDING MM 61 - 78 – 90 – 116- CONSOLE ELECTRIC MOVABLE ON WHEELS ALL THE CONTROLS CENTRALIZED DIGITAL POSITION READOUT OF BENDING ROLLS UPPER ROLL DRIVEN MOTORIZED ELECTRIC POWERED WITH GEAR UNIT SIDE ROLLERS HYDRAULIC ADJUSTMENT POWERED INDEPENDENT WITH PISTON MACHINE REVERSIBLE CAN WORK WITH SHAFTS VERTICAL/HORIZONTAL. SAFETY AND EMERGENCY STOP EQUIPMENT INSTALLED WITH THE MACHINE MANUALS AND SCHEMATICS IN ORIGINAL ALONG WITH THE MACHINE WEIGHT 1000 KG DIMENSION 1260 X 1000 X H 1260 MM

Condition: used, Year of construction: 1992, spindle diameter: 50 mm, milling spindle length: 545 mm, Longitudinal profile milling machine with lifting spindle 545mm long, diameter of lifting spindle D=50mm, motor 5.5kW. Glazing bead saw D=180mm, 2,2kW. Feed rate 2-4-6-12m/min Isdpoua Swwsfx Ap Djtn

Year of construction: 2006, condition: ready for operation (used), Travel X/Y/Z: 12100mm/2350mm/800mm, swivel A-axis: +/-98°, rapid traverse X/Y/Z/A: 45/45/24/10 m/min, processing length: 11000mm, speed: 24000 rpm, table: 10 support crossbars, 2 hydraulically swiveling workpiece stops, control: BWO 930, operating hours: 23792h, dimensions X/Y: 18300mm/6250mm. Including moving gantry version with Gentry drive on both sides, coolant spraying system with minimum quantity fine atomization. Documentation available. Ijdpfxotqfqxo Ap Dstn

Condition: new, number of rollers: 3, shaft diameter: 50 mm, – Shaft diameter: 50 mm – Digital display Itjdpfx Apoz Dquuo Djn – Forward and reverse operation – Can be used horizontally and vertically – Foot pedal control – Emergency stop – Documentation – 400V

Condition: used, Year of construction: 1991, with 2 double-head linear grinding machines used, good condition Make: Reckmann Type GL 162 Year of manufacture 06/1991 Machine no. 1622 Workpiece width 10-100 mm Itjdpfx Asvwgihsp Djn Workpiece thickness 10-106 mm Number of units 2 x 2 Vibro longitudinal grinding units 2 double-head, tiltable 130 ° Pressure rollers from above Pressure from the side Digital display Feed speed 0-25 m/min. continuously variable Space requirement approx. 2500 mm x 1300 mm x 1300 mm Weight approx. 850 kg Storage location 97447 Gerolzhofen, free loading, unpacked Handed over in the current condition as viewed, without guarantee or warranty

Condition: excellent (used), Catalog number 7248 TECHNICAL DATA - max. workpiece height 160mm - spindle working length 250mm - spindle diameter 40mm - max. tool diameter 220mm - worktable dimensions (length/width) 420x1010mm - motor 11kW - 2 pneumatic workpiece clamps - dust extraction port diameter 180mm - dimensions (length/width/height) 1500x1010x1560mm - weight 689kg ADVANTAGES – Made in Germany – Used milling machine, very good condition Net price: 31900 PLN Net price: 7419 EUR, depending on the exchange rate of 4.30 EUR (Prices are subject to change due to currency fluctuations) Itedpszh H A Esfx Ap Dsn

Condition: good (used), Year of construction: 2000, CNC flat and profile grinding machine Manufacturer: Ziersch & Baltrusch Type: PROFITLINE ZB 62 NC Year of manufacture: 2000 Ijdefrbckopfx Ap Detn Grinding area: 600 x 270 mm Electro-magnetic chuck with continuous transverse division 600 x 200 mm, pitch = 4 mm Wet grinding system, with paper band filter automatic, machine tray. Complete machine documentation available.

Year of construction: 2018, condition: excellent (used), For machining aluminium and steel profiles Fully functional, in very good condition Machining length: 7200mm 3-axis control with 15" screen Tool changer: 8 positions / turret 8 pneumatic horizontal material clamps Autonomous clamp positioning Two separate work zones, suitable for pendulum operation 2 pneumatic material stops 8 tool positions / BT30 turret Barcode scanner Handheld control unit Safety light barrier at the front and side safety fence Minimal quantity lubrication Central lubrication Thread cutting without compensating chuck Simple programming at the control panel High-speed spindle up to 18,000 rpm Including 3 angle heads X-axis [mm]: up to 7,200 / 7,200 Y-axis [mm]: up to 485 / 310 Z-axis [mm]: up to 340 / 260 Rapid traverse speed X/Y/Z axis [m/min]: 60/60/60 Max. milling cutter diameter: 25mm Max. saw blade diameter: 180mm Itjdpfezzw Edox Ap Don Max. tool length: 200mm (tool + holder) Max. spindle speed: 6,000 rpm Spindle power: 6 kW Weight: approx. 5.5 t Total operating hours: 30,844 h Total spindle hours: 11,583 h

Condition: used, Year of construction: 1995, Technical details: grinding length: 1250 mm grinding width: 600 mm workpiece height: 730 mm table surface area: 1720 x 500 mm headstock: dist. table - spindle center: 900 mm max. longitudinal movement: X-1450 feed range: 10 - 20.000 mm/min vertical movement: Y-730 mm feed range: 0,2 - 3.000 mm/min cross travel: Z-550 mm feed range: 5 - 5.000 mm/min power capacity: 1500 U/min.- 44 kW / 8000 U/min. - 38 kW kW grinding wheel turining speeds: 50-6.000 U/min cutting speed: max. 80 m/sec. weight of the machine ca.: 11 t with CNC SIEMENS 840 C auto. dynamic balncing system integrated in the grinding conus profile grinding unit ( on table mounted ) Diamant profile rollers ( dia. max 140 mm , width max. 200 mm, hole 52 H3 ) speed 3000 rpm Itjdpfxsx Uzvpj Ap Djn two magnetic plates ( 1000 x 400 mm, 1200 x 350 mm ) divers Flanges ect. *

Condition: good (used), Code: 0375 Brand: GREDA Model: CFL 4 - CE Standard Contouring, milling, and sanding machine for contouring and milling on two opposing sides of a piece of wood, such as chair, armchair, sofa, gun handles, and various - CE Standard Technical data: N° 2 milling units N° 2 milling and sanding units N° 4 motors 7,5 Hp each N° 4 rotation reversals Max workable length 2500 mm Max workable height 180 mm Min/max workable width 20/320 mm Milling unit shaft diameter 35 mm Max milling tools dimensions diameter 160 mm - height 180 mm Carriage feed 30 mt/min Carriage return 30 mt/min Automatic table slowdown with stops Sanding belt length 2500 mm Automatic positioner N° 6 adjustable pressers Total installed power 36 Hp Compressed air 6 bar Itedpfx Apsy Iwvro Djn Overall dimensions mm 6700 x 2200 x 1800 h Weight kg 3600

Condition: good (used), functionality: fully functional, *Description* Hydraulic shear and punch press *GEKA model HYD 50-S* No. 3497. Versatile 5-station machine, ideal for cutting and punching steel profiles. Robust machine, visible and in working order. *Technical Specifications* - *Brand / Model*: GEKA HYDROCROP HYD 50-S Itodpfozt Swlex Ap Den - *Machine No.*: 3497 - *Punching force*: 50 tons - *Bending force*: 50 tons *Capacities with standard blades* - *Angle iron*: 120 x 120 x 10 mm at 90° - *Flat bar*: 300 x 15 mm - *Round bar*: Ø 40 mm - *Square bar*: 40 x 40 mm - *Punching*: Ø28 x 13 mm thickness *Special Equipment* - *Bending*: 200 x 15 mm - *Notching*: 250 x 250 x 6 mm - *Shear for UPN/UPE*: 100 mm - *Shear for IPN/IPE*: 100 mm *Condition* Complete machine with stations: punching, flat/angle/round/square shearing, bending, notching. Sold with punches. Heavy weight, mounted on a steel base.

Condition: excellent (used), Year of construction: 1998, control type: CNC control, controller model: SIEMENS TOUCH, number of rollers: 3, overall weight: 15,000 kg, total length: 2,600 mm, total width: 2,200 mm, total height: 2,300 mm, Profile bending machine FACCIN - RCMI 180 Itsdpfjz Iwy Sox Ap Don MACH-ID 9828 Make: FACCIN Type: RCMI 180 Control: SIEMENS TOUCH YOP: 1998 Power 30 kw Hydraulic side supports 3 roll driven  Touchscreen SIEMENS Panel with S7 SPS  Laser measuring device for Radius  Set Universal rolls hardned Set Tool points  Horizontal and vertical:Horizontal Shaft Ø: 190mm Number of rolls: 3 Stroke X-Axis: 500mm Resistance moment: 360CM³ Working speed: 2000 - 5000mm/min. Length: 2600mm Width: 2200mm Height: 2300mm Weight: 15000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!