Used Raising Machine for sale (65,882)

Condition: used, SincoTec Type: Exciting Mot Resonance test bench POWER SWINGLY 20 kN The POWER SWINGLY BigTable resonance test bench is designed as a dual-mass vibrator. It consists of a vibration head, which is excited via an asynchronous motor with frequency control and an eccentric motor. The vibration head is located in the upper part of the machine and generates the dynamic amplitude. The vibration head is supported on the upper traverse via pre-tensioned coil springs and is guided centrally. The center load drive is located in the lower part of the machine and applies the static preload with the aid of a geared motor via a spindle drive. The test chamber is located above the mounting table and is bounded upwards by the adjustable traverse. The control of the test bench is carried out by the EXCITING MOT control system. The complete control electronics for the control system are housed in an industrial PC cabinet. The control cabinet is made of powder-coated steel sheet and meets protection class IP 50 according to EN 60529. Technical data: General data of the test bench: Overall height of the test bench 1840 to 2240 mm Height of the machine table 1030 mm Width of the test bench 800 mm Depth of the test bench 1500 mm Height of the test chamber max. 600 mm (without force sensor) Free column passage 550 mm Maximum force amplitude 10000 N Maximum total force ±20000 N Maximum stroke ±5 mm Test frequency 30 to 110 Hz Accuracy of the measuring sensors min. class 1 (according to DIN EN 10002-3) Weight of the test bench approx. 1880 kg Max. weight of the clamping device 150 kg General data of the control cabinet: Overall height of the control cabinet 1900 mm Height of the table top 1080 mm Width of the control cabinet 650 mm Depth of the control cabinet 700 mm Weight of the control cabinet 152 kg Color RAI 9006 (white aluminum), table top Midnight Conditions for the installation site: Isdpszii Awofx Ap Debc Space requirement 2.5 x 2.5 m Required ceiling height 2.8 m Floor load-bearing capacity 170 N/cm² Voltage supply 400 V / 50 Hz (right-rotating field) Connection plug CEE socket, 5-pole, 16 A Fuse 16 A Connection and environmental conditions Mains conditions: Voltage 400 V three-phase with PE conductor and protective earth, right-rotating field Voltage fluctuations < ± 10% Short-time voltage dips < 20 ms Limits for permanent interference Radio interference level A according to VDE0871 Frequency 50 Hz ± 1% Protective earth Ground resistance < 0.3 Ω Model: POWER SWINGLY MOT Condition: used Scope of supply: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, ZEISS Multisensory CNC Coordinate Measuring Machine O-INSPECT 442 Professional coordinate measuring machine for optical and tactile precision measurements in industry, research, and quality assurance. For sale is a used multisensory coordinate measuring machine from the manufacturer Carl Zeiss IMT GmbH. The ZEISS O-INSPECT 442 combines highly precise optical and tactile measurement technology in a CNC coordinate measuring machine. The installed ZEISS CALYPSO measurement software enables convenient evaluation of measurement data as well as the display of the actual state, target profile, and deviations. The system is ideal for quality assurance, toolmaking, precision engineering, medical technology, as well as research and development. Technical data: Manufacturer: Carl Zeiss IMT GmbH Model: O-INSPECT 442 Type: Coordinate measuring machine Measuring range X: 400 mm Measuring range Y: 400 mm Measuring range Z: 200 mm Max. workpiece weight: 20 kg Noise level: < 70 dBA Measurement system: Multisensory measurement system Optical and tactile measurement CFS measuring head system CALYPSO measurement software CNC-controlled measurement sequences Electrical data: Supply voltage: 100 / 110 / 120 / 125 / 230 / 240 V AC (±10 %) Current type: 1 / N / PE Frequency: 50–60 Hz (±3.5 %) Power consumption: max. 1500 VA Dimensions: Width: 1,055 mm Depth: 1,351 mm Height: 1,770 mm Weight: Coordinate measuring machine: approx. 800 kg Max. workpiece weight: 20 kg Equipment: Integrated control Control panel Computer with peripherals ZEISS CALYPSO Software 5.2 Documentation CFS measuring head system Reference probe Calibration standard Calibration template Applications: Coordinate measuring technology Optical measuring technology Tactile measuring technology Quality assurance Toolmaking Precision engineering Ibsdpfozii Dhjx Ap Dec Medical technology Research and development Scope of delivery: ZEISS O-INSPECT 442 coordinate measuring machine Integrated control Control panel Computer with peripherals ZEISS CALYPSO Software 5.2 Documentation Measuring head system Reference probe Calibration standard Calibration template Accessories as shown in the pictures Condition: Used Optical condition as shown in the pictures. Normal signs of wear and tear due to age. The table shown in the photos or other items not explicitly mentioned are not included in the sale. Due to its size and weight, shipping is possible via a freight forwarder. Subject to changes, errors and prior sale. We would be happy to answer any further questions by telephone.

Condition: used, SLM Solutions Type: SLM 280 HL For sale is a professional metal 3D printing system, type SLM 280 2.0, from SLM Solutions (Lübeck). The SLM is designed for 24/7 operation and was last used with titanium. Installation was in 2018. The system already has the sintering walls for gas flow. The system has only been operated with argon for the last 3 years. Approx. 50,000 laser hours. The 50,000 hours refer to the laser on-time; the exposure time is not recorded in the older 280 models. If I disregard the coating time, I estimate approximately 10,000 active laser hours. Last maintenance was in early 2026. Currently, occasional communication issues between the PC and the PLC are observed. In rare cases, this can lead to incorrect status messages, which can cause the system to be briefly interrupted during a running job. Technical data (excerpt) Single laser 400W Weight: 1,245 kg Build volume: 280 × 280 × 365 mm Laser: 1 × 400 W fiber laser (IPG) Optics: 3D galvo system Focus diameter: 80 – 115 µm Max. scanning speed: up to 10 m/s Layer thickness: 20 – 90 µm Minimum feature size: approx. 150 µm Build speed: up to approx. 113 cm³/h (material-dependent) Materials: Stainless steel, tool steel, titanium (Ti64), aluminum, Inconel, CoCr Inert gas: Argon Gas consumption process: approx. 2.5 – 8 l/min Gas consumption purging: approx. 70 – 110 l/min Compressed air: approx. 6 – 7 bar Electrical: 400 V, 3P+N+PE Fuse: 63 A Power consumption: approx. 3.5 – 5.5 kW Ibjdszhlr Eopfx Ap Doc Machine dimensions: approx. 2600 × 1200 × 2700 mm Weight: approx. 1300 kg (empty), up to approx. 1800 kg (including powder) Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of supply: (See image) SLM 280 machine Control cabinet Process chamber Internal control panel with screen (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Zwick / Roell Material Testing Machine / Universal Testing Machine Zwick / Roell Z020 Allround-Line BT2-FR020TNW.A50 20 kN material testing machine for tensile and compression testing with testControl II & testXpert V3.5 For sale is a used material testing machine from the manufacturer Zwick / Roell. The machine is suitable for tensile and compression tests on metals, plastics, elastomers, composite materials, and numerous other materials in the laboratory, quality assurance, research and development. Technical data: Manufacturer: Zwick / Roell Model series: Z020 Allround-Line Type: BT2-FR020TNW.A50 Testing force: 20 kN Testing direction: Tensile & Compression Testing space height: 1000 mm Crosshead speed: 0.0005–1000 mm/min Power connection: 230 V / 50–60 Hz Power consumption: 8 A Electronics: testControl II Software: Zwick / Roell testXpert V3.5 Equipment: Servo-electric material testing machine testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Testing table Test fixture Various connection and cable sets Accessories as shown in the pictures Dimensions and weight: Machine dimensions (approx.): 1244 × 690 × 1324 mm (W × D × H) Weight: approx. 212 kg Iedpfozra Rqsx Ap Debc Application areas: Tensile testing Compression testing Material testing Quality assurance Research & Development Testing laboratory Education and training Scope of supply: 1 × Zwick / Roell Z020 Allround-Line material testing machine testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Connection and cable sets Further accessories as shown in the pictures Condition: Used Visual condition as shown in the pictures Functional scope as shown in the pictures Nameplates are present The table, monitor, keyboard, and mouse shown in the photos, as well as any other items not explicitly mentioned, are not part of the sale. Shipping or freight forwarding possible. Subject to change, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: used, Desktop Metal Desktop Metal 3D Printer Complete System 3D Metal Printer Studio System from Desktop Metal Complete system: 3D printer + debinding machine + sintering furnace Desktop Metal The three-part solution includes a 3D printer, debinder, and furnace. Manufacturer: Desktop Metal Model: Desktop Metal Studio System Operating condition: Used (Good) Year of manufacture: 2019 Includes: Bound Metal Deposition (BMD) technology Features: Printed materials: Metal Technology: FDM Application: Industrial Other features: Office X-axis travel: 30 cm (12 in) Ijdozd Tllepfx Ap Dobc Y-axis travel: 20 cm (8 in) Z-axis travel: 20 cm (8 in) Description: In contrast to laser-based systems that selectively melt metal powder, the printer extrudes bound metal rods – similar to an FDM printer. This eliminates the safety requirements often associated with 3D metal printing, and enables new features such as the use of closed-cell fillings for lightweight strength. Desktop Metal Studio Debinder (Delamination machine) Fully automatic debinding Cleaning tank: 17.4 L (in process) / 22.5 L (storage) Description: The debinder prepares green parts by dissolving the primary binder for sintering. With a low-emission design, it requires no external ventilation and is safe for an office environment. Automatic liquid distillation and recycling mean that no refilling is required between cycles. Desktop Metal Studio Sinter Furnace Hybrid technology (microwave & conventional heating elements) Build volume: 305x205x205 mm Carbon housing Gas supply: 2 x 900 L gas cylinders Heating power: 20 kW Function: Sintering Configuration: Chamber Heat source: Gas Other features: High temperature, automatic Maximum temperature: 1,400 °C (2,552 °F) Description: Fully automated and sized to fit through an office door, the furnace delivers industrial-grade sintering in an office-friendly package. Built-in temperature profiles, tailored to each design and material, ensure uniform heating and cooling without the residual stresses that occur in laser-based systems. Condition: used Scope of delivery: (See image) (Changes and errors in technical data, information is subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Applied Type: Applied Biosystems ViiA7 Biosystems ViiA7 Specifications: Block change from the front of the instrument in less than 1 minute; no secondary tools required Supported applications: Standard curve, comparative CT, genotyping, presence/absence, HRM, melting curve Temperature uniformity: ±0.5 °C, within 30 seconds after reaching the target temperature Run time: ~35 min for 96/384-well blocks with Applied Biosystems® Fast Master Mix Supported blocks and volumes: 96-well standard (10–100-μl reactions) Ibodpfx Aozd Ud Nop Dec 96-well Fast (10–30 μl reactions) • 384-well (5–20 μl reactions) TaqMan® Array Micro Fluidic Cards (~1 μl reactions) Detectable sensitivity: up to 1 copy • Excitation/detection wavelengths: 6 excitation (450–670 nm) 6 emission (500–720 nm) • Dynamic range: Up to 9 logs linear dynamic range Resolution: Detects only 1.5-fold changes in target quantities in a singleplex reaction 21 CFR p11 Enablement: Security, audit, and e-signature functions for instrument data Automation: Includes plate loading arm with barcode (distribution, service, and support provided by Life Technologies) Remote notification: Notifies the user via email when the run is started, stopped, or aborted Data export format: Fully configurable by the user Description: Applied Biosystems Real-time PCR ViiA7. Ideal for performing real-time PCR with medium to high throughput. Interchangeable blocks for 96-well, Fast 96-well, and 384-well plates, as well as TaqMan Array Cards. Fast block change. Touchscreen interface. 2x Ethernet connection. 2x USB connection. 1x RS 232 connection. 2x connection on the display. Weight: 67 kg Condition: used Scope of supply: (See picture) (Changes and errors in technical data and information are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: used, Haida Type: HD-B604-S Sensor: TECSIS load cell Max. Capacity: 2T / 20 kN Unit: G, kg, N, LB (adjustable) Resolution: 1/250,000 Accuracy: ± 0.5% Max. Stroke: 700 mm (without fixture) Test speed: 0.1-500 mm/min (adjustable) Voltage: 220V AC ± 10%, 50/60Hz Chuck: 0-7 mm Iedpfx Aozgr Eijp Dobc Weight: approx. 175 kg Dimensions (W x D x H): 88 x 50.5 x 150 cm Condition: used Scope of delivery: (See picture) (Subject to changes and errors in the technical data!) We will be happy to answer any further questions you may have by phone.

Condition: used, Trumpf Type: TC 6000 L 1300 Laser and punching machine Technical data: Power supply: 400V/50 Hz Fuse rating: 3 x 100 A Connected power: 65 kVA Working area X x Y without repositioning: Combined operation: 2585 x 1280 mm Punching operation: 2585 x 1370 mm Laser operation: 2585 x 1280 mm Performance: Laser: 2000 W Maximum sheet thickness: 8 mm Maximum punching force (including 20 kN holding-down device): 220 kN Active holding-down device (programmable in stages): 4.5-20 kN Maximum workpiece weight: 200 kg Maximum clearance height: In punching operation: 35 mm In laser operation: 22 mm Speeds: X-axis: 90 m/min Y-axis: 60 m/min Simultaneous movement: Punching: 900 min Marking: 2800 min C-axis: Punching: 60 revolutions/min Thread forming: 330 revolutions/min Tools: Tool stations on linear magazine: 19 with 2 grippers Number of tools when using a multi-tool: 19 to 190 tools Rotation of all tools: 360° Tool change time: 1.5-5 s Maximum punching diameter: Single stroke: 76.2 mm on all tool stations Standard multi-cut: 200 mm Maximum bending height: 25 mm Maximum part size: 500 x 500 mm Accuracy: Positioning deviation: ± 0.1 mm Average position spread: ± 0.03 mm TRUMPF CNC control: Base: Siemens SINUMERIK 840D Loading and dismantling must be handled by the buyer! Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone. Ibedpfxezd Ulas Ap Djc

Condition: used, Mitutoyo   Quick Vision Apex QV-X404P1L-C CNC Image Processing Measuring Machine / Optical Measuring System   Manufacturer: Mitutoyo Corporation Type: QV-X404P1L-C Code No.: 363-131EU Professional CNC image measuring system for non-contact dimensional measurement tasks   For sale is a used Mitutoyo Quick Vision Apex CNC image processing measuring machine, including existing PC system, two monitors, control unit, measuring software, and extensive documentation.   The existing PC system and the installed QVPAK software start up. However, the complete machine and measuring function could not be fully tested.   The Quick Vision series is used for non-contact dimensional measurement of workpieces by means of an optical system, image acquisition, and image processing. Suitable for precise measuring and testing tasks, among others, for components from the fields of electronics, precision mechanics, and industrial manufacturing.   Technical data:   Manufacturer: Mitutoyo Corporation Model: Quick Vision Apex Type: QV-X404P1L-C Code No.: 363-131EU Country of Manufacture: Japan Machine type: CNC image processing measuring machine   Measuring range X / Y / Z: approx. 400 × 400 × 250 mm Measuring principle: non-contact optical image measurement CNC-controlled measuring system   Existing measuring software: Mitutoyo QVPAK QVPAK (R): Version 7.502.0010 QVGEO: Version 7.502.0010 Statistics: Version 7.502.0010   Equipment:   Mitutoyo Quick Vision Apex measuring machine PC workstation Fujitsu Siemens CELSIUS PC system 2 Fujitsu monitors Keyboard and mouse Mitutoyo control unit / joystick with emergency stop QVPAK measuring software Mitutoyo MCOSMOS / MiCAT data carriers GEOPAK documentation QVPAK documentation Other Mitutoyo operating manuals and documents Clamping plate / workpiece fixture as shown in the pictures Connection cables and accessories as shown in the pictures   Application areas:   Optical dimensional inspection Non-contact workpiece measurement Quality assurance Precision metrology Component and contour inspection Manufacturing and process control   Scope of delivery:   Mitutoyo Quick Vision Apex QV-X404P1L-C with PC workstation, monitors, control unit, existing software, documentation, and accessories as shown in the pictures. Scope of delivery is limited to what is shown in the pictures.   Condition: Iedpfx Ajztyabjp Debc   Used Optical condition according to pictures PC system and existing QVPAK software start up. Signs of wear and tear due to age and use are present. Visible damage / signs of wear are present on the machine housing, see pictures.   Important note: The machine has not been tested, as it is in a protective mode after being moved. This is also intended by the manufacturer when transporting the machine. The machine must be recommissioned by qualified Mitutoyo personnel.   Shipping by freight forwarder is possible. Subject to changes, errors and prior sale.   We would be happy to answer any further questions by telephone.

Condition: used, INSTRON Spring Testing Machine / Universal Testing Machine SPRING SF1392-E1-L12-SPL Professional 100 kN testing machine for spring, compression, and material testing For sale is a used spring testing machine from the manufacturer INSTRON. The system was designed for highly precise spring, compression, and material testing. It is ideal for use in testing laboratories, research and development, quality assurance, and industrial manufacturing. Technical data: Manufacturer: INSTRON Type: SPRING Model: SF1392-E1-L12-SPL Serial number: SPRGK4348 Year of manufacture: 2007 Testing force: 100 kN Power supply: 240 V AC / 1~ / 50–60 Hz Mains current: 25 A Control voltage: 24 V AC / 50–60 Hz Max. ambient temperature: 40 °C Dimensions: Machine (W × D × H): approx. 1,307 × 757 × 2,392 mm Sliding door with 0 mm additional opening space Base Extension Model: 2910-061 Weights: Testing machine: approx. 1,145 kg Base Extension: approx. 96 kg 5800 Controller: approx. 31.8 kg Total weight: approx. 1,273 kg 5500 Controller: Dimensions (H × W × D): 650 × 280 × 570 mm Weight: approx. 31.8 kg Equipment: 100 kN testing frame Protective enclosure with sliding door Base Extension Model 2910-061 Instron 5500 Controller Operating console Industrial PC Monitor Keyboard Mouse Emergency stop system Testing platens / compression tools as shown in the pictures Technical documentation as shown in the pictures Application areas: Ibsdpjzlp Ixsfx Ap Dec Spring testing Compression testing Material testing Component testing Load testing Material testing Quality assurance Testing laboratory Research & Development Scope of delivery: Instron SPRING SF1392-E1-L12-SPL Base Extension Model 2910-061 Instron 5500 Controller Operating console Testing platens / compression tools as shown in the pictures Machine accessories as shown in the pictures Technical documentation as shown in the pictures Important note: To operate the system, the original Instron testing software including a valid software license is required. The software and the software license are not included in this offer. According to the manufacturer, a corresponding retrofit is required for recommissioning. A functional test could not be carried out due to the missing software. The sale is therefore preferably aimed at specialist companies for recommissioning or upgrading. Condition: Used Optical condition according to the pictures. Normal signs of wear and tear are present. The workbench shown in the photos is not part of the sale. The operating console and the machine accessories shown are included in the scope of delivery. Transport information: Original shipping dimensions according to the manufacturer: 2,795 × 1,600 × 1,295 mm (L × W × H) Shipping weight according to the manufacturer: approx. 1,565 kg Loading with a forklift is possible. Shipping via a freight forwarder is possible. Subject to changes, errors and prior sale. We will gladly answer any further questions by telephone or email.

Condition: used, Shimadzu Type: AG-X plus 20kN-50kN +750mm Isdozimkfspfx Ap Debc Dimensions: W 1206 x D 765 x H 2920 mm Technical data: Fmax: 50 kN Speed: 0.00005~1500 mm/min Accuracy: ±0.1% JIS B7742 Class 0.5, ASTM E2658 Class A Crosshead-table distance (mm) (tensile stroke)*3: 215 to 1940 (20 kN: 0 to 1535 mm, 50 kN: 0 to 1475 mm) Possible test width: 600 mm Frame stiffness: 180 kN/mm 710 kg 200 V 4.5kVA/15 A + Accessories as shown in the picture Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and specifications are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Zwick Testing Machine Type: Z20 Controller: BX1-EZ020.A4K-000 Technical Data: Stroke: 200 mm Piston dimensions H x W x D: 1037 x 385 x 180 mm Fmax: 20 kN Vmax: 125 mm/s Accessories: Iodpfx Aozil Upop Dobc ClipOn extensometer, 13.5 mm MFA 25 extensometer (temperature range up to +200°C) Computer + testXpert II V3.5 software Climate chamber: Airtemp LKG-K-TK-50 Temperature range: -40°C to +150°C Climate temperature range: 20°C to +90°C Humidity range: 10% to 95% Test chamber volume: 50 liters Temperature change rate: 1 K/min Refrigerant: R404, 5 kg Voltage: 400V 3Ph/N/PE/50 Hz 16 A 9 kW Condition: used Total weight: approx. 1500 kg Scope of delivery: (See image) (Subject to changes and errors in the technical data and specifications!) We will be happy to answer any further questions you may have by phone. Written orders can be placed by email or fax.

Condition: used, Zwick Type: Z30 Technical data: Overall height 2114 mm, width 748 mm, depth 580 mm Fmax: 30 kN Vmax: 125 mm/s Accessories: Extensometer ClipOn 13.5 mm Extensometer ClipOn 40 mm Computer + testXpert II V3.5 software Total weight approx. 500 Condition: used Ibjdpezil Ucefx Ap Doc Scope of delivery: (See image) (Subject to changes and errors in the technical data and specifications!) We will gladly answer any further questions you may have over the phone.

Condition: used, Zwick / Roell Type: Z020 Allround-Line BT1-FR020TN.A50 Zwick / Roell Material Testing Machine, 20 kN, Tensile & Compression Testing, testXpert III For sale is a high-quality Zwick / Roell material testing machine for professional tensile and compression testing of materials and components. The machine is suitable for metals, plastics, rubber, and many other materials and is typically used in laboratories, quality assurance, research, and education. The machine is controlled via a PC with Zwick/Roell testXpert III software (storage medium and documentation available). Technical Data: Nominal testing force: 20 kN Testing direction: Tensile & Compression Power connection: 230 V / 50–60 Hz / 1-phase Power consumption: approx. 2.1 kVA Weight: approx. 150–180 kg Dimensions: approx. 856 × 650 × 1,545–2,114 mm Technical Data (from documents & nameplate) Mechanics / Testing Nominal force: 20 kN Testing direction: Tensile & Compression Max. testing frequency: 0.5 Hz Crosshead: servo-electric Positioning accuracy: < 1 µm Speed range: 0.0005 – 1,000 mm/min Dimensions & Weight Overall height: approx. 1,545 – 2,114 mm (depending on the crosshead position) Overall width: approx. 856 mm Overall depth: approx. 650 mm Working space width: 440 mm Weight: approx. 150 kg (basic unit) approx. 180 kg with typical equipment Electrical Data Power connection: 230 V AC Ibodpjzimgtsfx Ap Dsc Phases: 1-phase (1PH, N, PE) Mains frequency: 50 / 60 Hz Current consumption: approx. 8–10 A Power consumption: approx. 2.1 kVA Socket: Schuko (CEE 7) Measuring & Control Electronics Internal measurement value acquisition: 500 Hz Data transmission to PC: 10–100 Hz adjustable Interface: RS232 (COM) Protection class for electronics housing: IP32 Important note: “The table shown in the photos is not included in the sale.” Condition: used Scope of supply: (See picture) Zwick / Roell material testing machine (20 kN) Electronics unit PC workstation (monitor, PC condition see pictures) 2 measuring modules (Delock units) Zwick/Roell testXpert III software (storage medium) Original operating and technical documentation Various connection and linking cables (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: used, Zwick/Roell Zwick/Roell ProLine Universal Testing Machine Z010 TN – 10 kN, Type: BT1-FB010TN.D30 For sale is a professional material testing machine from Zwick/Roell, suitable for tensile and compression tests up to 10 kN. The machine comes from an industrial setting and has been professionally operated. General Data: Manufacturer: Zwick GmbH & Co. KG, Ulm Rated force: 10 kN Type of test: Tensile and compression test Ibedjzizrkjpfx Ap Djc Technical Performance Data: Crosshead speed: 0.001 – 1,000 mm/min Speed accuracy: 0.01% of Vnenn (nominal speed) Displacement resolution: 0.038 µm Positioning repeatability: < 2.0 µm Maximum test frequency: 0.5 Hz Data acquisition rate: 500 Hz Data transfer to PC: 10–100 Hz Force measurement according to ISO 7500-1 Dimensions & Weight: Height with leveling elements: approx. 1,331 mm Width with electronics: approx. 930 mm Depth with electronics: approx. 437 mm Working space width: 440 mm Working space height (bottom): 1,050 mm Weight with typical components: approx. 160 kg Electrical Data: Adjustable mains voltage: 100–250 V Mains frequency: 50 / 60 Hz Power consumption: 800 VA Current consumption at 230 V: approx. 3.4 A Fuse rating: ≤ 16 A Connection: 1L / PE / N Documented test and calibration records: 18.09.2017 Machine BT1-FB010TN.D30 testXpert II Version 3.2 tC-PC System Temperature during testing: 23.3 °C Displacement measurement system: Incremental encoder (rotary) Force sensor installed 29.01.2014 Force sensor: Xforce HP Module: DCSC Calibration at Zwick Ulm 28.08.2013 Force sensor: Xforce P Module: DCSC Rotation before test series: 120° testXpert control system Documented service and calibration records are available. Software & Control: Software: testXpert® II Documented version: V3.2 Installation documentation from version 2.2 Documentation status: March 2010 PC control: tC-PC Interfaces: RS232 / Ethernet Note: testXpert II is a professional industrial testing software. Installed Modules & Components DCSC measuring module Force sensor Xforce P / Xforce HP Incremental encoder (rotary displacement measurement system) ISO 7500-1 compliant force measurement Installed under the traverse Important Note: “The table shown in the photos is not part of the sale.” Condition: used Scope of delivery: Material testing machine BT1-FB010TN.D30 PC with monitor Force sensor DCSC module Specimens / Grips Adapters and holders Tools Documentation folder with documents Scope of delivery as shown in the pictures. (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, total length: 4,750 mm, total width: 2,640 mm, total height: 2,030 mm, Colour: White Empty weight: 3.500 kg The Bauerrichter ESR-1 is a polisher designed for creating high-gloss surfaces on various materials. Below is a summary of its technical specifications: Technical Specifications: CharacteristicSpecificationElectric connection380 V, 20 kDimensions (L x W x H)5,600 mm x 2,400 mm x 2,100 mmWeightAbout 3,000 kgWork table dimensions1,350 mm x 3,200 mmMaximum workpiece height< 100 mmDiameter polishing rollerØ 400 mmFeed rateFrequency controlled Characteristics: Ibjdjwnhxdspfx Ap Doc Polishing unit:Moves over a fixed work table and is equipped with an inclined, oscillating polishing roller. The height and oscillation speed are infinitely adjustable. Polishing roller: Equipped with special 400 mm diameter polishing rings that ensure longer life and lower operating costs. Quick-change system: Allows easy and quick replacement of polishing rings, reducing set-up time. Workpiece attachment: Standard equipped with a quick clamping system; optional vacuum clamping system is available for faster and more comfortable operation. Construction: Robust welded precision work table with phenolic resin bonded film plates, resistant to heat, moisture and chemicals. Drive: High quality SEW electric motors with energy efficiency class EFF1 (IE2), known for their robustness and durability. This machine offers an efficient solution for polishing various materials and is designed with durability and ease of use in mind. - CE marking present: Yes - Serial number: 150610 - Number of units [pcs]: 2 - └ Unit 1: - - Position: Top - - Type of unit: Brush unit - - Number of brushes [pcs]: 1 - - Brush length [mm]: 1500 - - Brush diameter [mm]: 180 - - Motor power [kW]: 11 - └ Unit 2: - - Position: Top - - Type of unit: Brush unit - - Number of brushes [pcs]: 7 - - Brush length [mm]: 75 - - Brush diameter [mm]: 180 - Max. working width [mm]: 1440 - Max. passage height [mm]: 250 - Infeed table length [mm]: 5150 - Outfeed table length [mm]: 5150 - Voltage [V]: 400 - Transport dimensions: 4750mm x 2640mm x 2030mm (l x w x h) - Transport weight [kg]: 3500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2018, x-travel 620 mm y-travel 350 mm z-travel 400 mm Isdpoz St Nrofx Ap Dobc table surface area 820 x 420 mm Maximum weight on the table 300 kg milling head -swivable +/- 90 ° Speed range - 2 levels 0 - 4.500 U/min feed speeds 0 - 2.000 mm/min rapid traverse 5.000 m/min total power requirement 7 kW weight of the machine ca. 1,65 t dimensions of the machine ca. 2,25 x 1,9 x 2 m

Condition: good (used), Spot welding machine, spot welding system, spot welding gun, resistance spot welding machine, lever-operated spot welding machine, roller seam welding machine, projection welding machine -Manufacturer: Dalex, spot and projection welding machine with roller table -Type: PMS 14-4 -Rated power: 200 kVA -Protrusion: 740 mm -Operation: via foot pedal -Individual components: including documentation, see photos -Submission/Price: complete -Dimensions: Machine 2120/890/H1680 mm / Table 2730/800H1055 mm -Weight: 966 kg / 70 kg Ibedpjy Au Eyofx Ap Dsc

Condition: used, operating hours: 13,672 h, total height: 2,450 mm, total length: 5,000 mm, total width: 2,200 mm, Year of manufacture: 2013 Empty weight: 9.000 kg - Year: 2013 - Documentation available: Yes - CE marking present: Yes - Serial number: 1237361A51A - Operating hours: 13672 - Drive system: CNC - Horizontal/vertical: vertical - Control system brand: Fanuc - Control system type: 0-MD - Power [kW]: 11.0 - Number of axes [pcs]: 3 - X-axis travel [mm]: 610 - Y-axis travel [mm]: 430 - Z-axis travel [mm]: 570 - Table length [mm]: 650 - Table width [mm]: 450 - Tool holder: BT40 - Main spindle power [kW]: 15 - Max. spindle speed [rpm]: 10000 - Options: Tool magazine, Chip conveyor, Spindle cooling, Pallet milling machine, Exchange table, External cooling - └ Tool magazine [pcs.]: 24 - Transport dimensions: 5000mm x 2200mm x 2450mm (l x w x h) Ibodpfx Apsyzzrko Djc - Transport weight [kg]: 9000kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, total height: 2,570 mm, total length: 3,520 mm, total width: 2,350 mm, Year of manufacture: 1996 Empty weight: 6.000 kg Iedpfx Apsw Slaxo Dobc - Year: 1996 - Documentation available: Yes - CE marking present: Yes - Serial number: M2058 - Drive system: CNC - Horizontal/vertical: Horizontal - Control system brand: Fanuc - Control system type: 18-M - Number of axes [pcs]: 3 - X-axis travel [mm]: 750 - Y-axis travel [mm]: 420 - Z-axis travel [mm]: 450 - Table length [mm]: 900 - Table width [mm]: 420 - Min. spindle speed [rpm]: 40 - Max. spindle speed [rpm]: 8000 - Transport dimensions: 3520mm x 2350mm x 2575mm (l x w x h) - Transport weight [kg]: 6000kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, total height: 1,900 mm, total width: 2,200 mm, total length: 1,500 mm, Year of manufacture: 1959 Colour: Blue Empty weight: 2.500 kg Price: On request - Year: 1959 - Documentation available: Yes - Serial number: 80 - Drive system: Conventional - Power [kW]: 5.0 - Transport dimensions: 1500mm x 2200mm x 1900mm (l x w x h) - Transport weight [kg]: 2500kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Ibjdpfszkui Ssx Ap Dec Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, functionality: fully functional, In this listing, you are purchasing a second-hand “Pfaff Creative Icon 2” sewing machine Items for sale: 1x Pfaff Creative Icon 2 with the following accessories: incl. additional embroidery module or embroidery unit incl. ‘Grand Endless Hoop’ fabric or embroidery material incl. embroidery hoop or embroidery accessories Condition: This listing is for a second-hand machine, which may show signs of wear (minor scratches or discolouration). The machine has been tested to ensure it is in working order Packaging and dispatch: You are welcome to view the machine during our opening hours. Please arrange an appointment to do so! Sturdy packaging and worldwide dispatch available on request! A video recording of a functional test will be made for you prior to dispatch or collection. For further information, please feel free to contact us directly. Ijdpfoz Sx Rujx Ap Dobc

Condition: good (used), Year of construction: 2011, functionality: fully functional, Heidenhain iTNC 530 CNC control Travel ranges: X-axis 1.016 mm Y-axis 610 mm Z-axis 760 mm Spindle speed 10.000 rpm Tool holder HSK 80 Power 12 kW Table clamping surface 1.250 x 590 mm Table load 900 kg Feed rate 40.000 mm/min. Machine weight 9.400 kg Equipment: Heidenhain iTNC 530 CNC contouring control Electronic handwheel 3D touch probe tool changer 2-position pallet table Coolant system with internal coolant supply (ICS) Chip conveyor Ijdpfsz S H H Djx Ap Djbc Oil mist extraction system

Condition: used, Year of construction: 2006, Control MAZATROL 640M x-travel 1.740 mm y-travel 760 mm z-travel 660 mm table dimensions 2.000 x 760 mm max. table load 1.400 kg spindle tunring speed 12.000 U/min tool taper SK 40 number of tool places 30 Pos. weight approx. 11.500 kg Condition: used Ibsdpfxsz S N I Do Ap Dec Accessories, tools, and clamping devices shown are included in the scope of delivery only if this is explicitly stated in the additional information. Subject to changes and errors in technical data and specifications; prior sale reserved!

Condition: excellent (used), Year of construction: 2020, MACHINING CENTER GANNOMAT "PROTEC 0571" working width 1300 mm Drilling, grooving, milling Base machine complete in standard version according to price list 01/19/D: For detailed technical data, please refer to the datasheet for PROTEC Type 0571 - Machining unit with: PowerBlock with 21 spindles and 1 slotting saw (BK 1341) - 13 vertical drilling spindles - 6 horizontal drilling spindles in Y - 2 horizontal drilling spindles in X - 1 grooving unit in Y 4th drilling axis in Y - Milling unit Profit F3 HSK63F with 3-position magazine for automatic tool change, 5.5 kW motor (S1), 1,000–20,000 rpm with frequency converter, clockwise and counterclockwise rotation, tool holder HSK63F with collet 462E, cutter length up to 130 mm. - INCLUDES OPTION: Iedpfxew Sguws Ap Debc Additional safety device with lamella curtain for processing Lamello P-System. Required for horizontal milling for Lamello P-System with groove cutter Ø 100.4 x 7 x 30 mm. - Workpiece sizes and weights: - Workpiece width (X): min. 60 mm / max. 1300 mm - Workpiece thickness (Z): min. 6 mm / max. 60 mm - Workpiece length (Y): min. 263 mm in through-feed mode, max. 5600 mm programmable workpiece length in software - Workpiece weight: max. 75 kg. - Air connection: 7 bar Machine No. 435.046 Electrical connection: (400V, 3Ph, 50Hz, (12kVA, 17.5A)) - Pressure device from above for working width 1300 mm - 765 mm roller table (Y-axis), foldable, for machine front, W 500 mm - 765 mm roller table (Y-axis), foldable, for machine rear, W 500 mm - Auxiliary stop 600 mm with integrated rollers for roller tables - Extraction distributor Ø 160 mm / Ø 80-80-80 mm, spacing 196 mm - Documentation in German: Operating manual: GERMAN Programming manual: GERMAN Operator software: GERMAN Operating system: ENGLISH Keyboard: GERMAN Location: ex stock 54634 Bitburg - immediately available -