Used Torque Tester for sale (2,619)

Condition: good (used), Year of construction: 2019, machine/vehicle number: 25653, Equipped with: -Automatic Central Lubrication System -Machine Guard -Indramat - MTX and Sercos CNC Control -The standard machine is equipped with CNC-control make Indramat - MTX and SERCOS-interface -Tool Dressing (Automatic dressing cycle of the dressing master and honing wheel tip diameter by a diamond coated dressing roll. The dressing cycle of workpieces can be pre-selected) -Electronic Indexing Unit -Operator and Maintenance Manual -All Electrical Drawings -PLC Language in English -Software and Hardware for Remote Diagnosis -High Precision Control of the Stock Allowance Material -Manual Loading on Spindle for Prototypes -Software for Infeed Optimized Cycle Type Reduction (Adaptive Honing) -Software for Vario Speed Dressing -Software for Calibration of Master Gears -Software for Timing Gears (including additional sensor for the hole of 4mm) -Software for Shortening of Workpiece Change-Over Time -Clamping Cylinder -RITTAL Cooling Unit -Lighting for Working Area -Installation of Vibration Detecting Sensors -Coolant Unit -Electrostatic Oil Mist Exhauster IFS With Rigid Piping -Internal Automation -Pallet Ring Conveyor System FlexLink (L-form shape see approved layout) -Parallel - Double Gripper -Pick and Placer Between Pallet Conveyor and Internal Loader -Extended Loading Length of the Pick and Placer Specifications: Workpiece: -Part Diameter: 20-150 mm -Maximum Face Width: 70 mm -Part Weight: 20 kg -Number of Teeth: 6-150 -Module: 1-5 mm Workpiece Spindle: -Maximum Speed: 6000 1/min -Installed Power: Approx. 25 kW Tool: -OD of Honing Wheel: 270 mm -Widths of Honing Wheel: 20-70 mm -Honing Wheel Material: Ceramics Tool Spindle: -Maximum Speed: 2000 1/min -Installed Power: Approx. 25 kW Machine: -Total Connected Load, Approx: 70 kVA -Floor Space (w x l x H): -Total Weight, Approx: 11 Ton -Bosch Rexroth MTX Control CML 85 Longitudinal Slide, Z-Axis: -Linear Drive -Drive Torque: 3,700 Nm -Infeed Speed: 60 m/min -Theoretical Infeed: 200 m/min -Drive Length, Maximum: 400 mm Cross Slide, X-Axis: -Linear Drive -Drive Momentum: 2,150 Nm -Infeed Speed: 60 m/min -Theoretical Infeed: 200 m/min -Drive Length, Maximum: 1050 mm Swiveling Axis, W-Axis: -AC-Servo Drive: 10,000 1/min -Setable Gear Transmission: i=5000:1 -Swiveling Angle: -90 Degrees / +16 Degrees Workpiece Spindle, C-Axis: Hedpfx Ajw Iquysgzjg -Direct Drive, Maximum RPM: 7,000 1/min -Drive Power: 30 kW -Drive Torque: 112 Nm -Digital Measuring System Tool Spindle, B-Axis: -Direct Drive (hollow spindle drive), Maximum RPM: 2000 1/min -Drive Power: 30 kW -Drive Torque: 150 Nm -Digital Measuring System

Condition: used, Year of construction: 2007, turning length 2500 mm control Sinumerik 840 D spindle head A 11 tool numbers 48 swing diameter over bed slide 750 mm Hsdpfx Agjwwaruezeg swing over bed 780 mm c-axis 0,1-30 1/min diameter of quill 160 mm taper bore MK 5 tool length - max. 500 mm weight of tools max. 15 kg weight of the machine ca. 27 t dimensions of the machine ca. 8,4 x 4,0 x 2,5 m Technical details: Nominal turning length: 2,500 mm Swing diameter over bed slide: 750 mm Swing diameter over bed: 780 mm Working height: 1,300 mm Spindle head to DIN 55026: A 11 Bore through: 123 mm Diameter in front bearing: 200 mm Oriented spindle stop: 0-359 degrees Drive power at 100/60 % duty cycle: 37/45 kW Total speed range: 10-2,500 1/min Number of speed ranges: 2 Speed range I: 10-775 1/min Speed range II: 20-2,500 1/min Max. torque at 60 % duty cycle: 2,500 rpm. Torque at 60 % ED: 2,083 Nm (up to 186 rpm)

Year of construction: 2000, condition: used, Sold for parts, ADU card missing. Automatic tablet testing system - Laboratory measuring equipment - Tablet tool Enables testing of: Hardness Diameter Thickness Weight Precision balance Sartorius WZ64S Scale : 10 à 50 g Hjdsx Riauepfx Agzsg Unit : mg / 0,5 mg / 0,1 mg adjustable Thickness Drive: stepper motor. Measuring principle: linear potentiometer. Unit of measurement: mm or inch. Tolerance: +/- 0.1 mm Hardness Drive: stepper motor. Measurement: load cell (lmz) Measurement principle: dynamometric gauge Unit: N, Kp or Sc Diameter Drive: stepper motor. Measuring principle: stepper motor. Unit of measurement: mm or inch. Scale: 3 - 18 mm / 3 - 30 mm (manual) Tolerance: +/- 0.1 mm Tension : 100 / 240 V, 50Hz / 60 Hz The UTS is a universal, fully automated testing system developed for use in industry. This tool is the approved model of a series of test systems that have been tested over many years. It was developed in close collaboration with the pharmaceutical industry. The UTS 4.1 can be used to test round, oval, square and oblong tablets, as well as many special shapes. For delicate oblong tablets, the proven oblong centring system (OZB) can be integrated. All parts requiring cleaning can be removed quickly and easily without any tools. The test system can be supplemented with various options, such as a distributor and/or sample collector with a different number of stations. Use the UTS as a laboratory tester or an online control device connected to a tablet press. Sampling can be triggered either in the production machine or using the TTS11 software.

Condition: used, Used Becomix model Beco Mini Lab homogenizing mixer.  Manufacturer: Becomix. Capacity: Working capacity maximum of 5 Litres approximately Dimensions: 820mm x 820mm x 1250mm high approximately Pressure: -1/+1 Bar maximum working pressure  internally; 4 Bar maximum working pressure of the external jacket Conical welded bottom with a clamped dish top. Pressure and vacuum sealed by a double acting axial seal rings and cooled by barrier water flow. Hedpfsx Nixusx Agzjg Bottom entry homogenizer: Power 1.55kW Torque 2.5Nm Weight: Estimated: Kg250.0 Dimensions: 820mm X 820mm

Condition: good (used), Gearbox, planetary gear for hydraulic motor, axle drive, gear axle drive, wheel drive, double planetary gear -Manufacturer: Trasmital Bonfiglioli, wheel drive -Type: 601R1L10BC5DODHP011 -Translation: 1 : 5 -Torque: 3000 Nm -Drive side mount: KW-21 splined shaft -Dimensions: see photos / technical drawing -Number: 20x gearbox available -Price: per piece -Dimensions: Ø 262 x 270 mm -Weight: 42 kg/piece Hjdpsr H Nlpofx Agzjg

Condition: used, Technical details: faceplate diameter: 1800 mm swing diameter: 2000 mm turning height: 1170 mm z-axis: 1000 mm cross rail adjustment - vertical: 800 mm Hodovb Db Nopfx Agzog faceplate speeds:: 2,5 - 280 workpiece weight: 12 t feeds: 1 - 6000 mm/min max. torque on the faceplate: 50000 Nm total power requirement: 85 kW weight of the machine ca.: 41 t dimensions of the machine ca.: 5,6 x 4,8 x 4,6 m Machine retrofit and overhould in 2005 with SIEMENS 840 D powerline control - 6 jaw hydraulic power chuck - tool changer for 12 tools - chip conveyor, coolant attachment, splash housing - various tool holders *

Condition: used, Year of construction: 2011, machine/vehicle number: 25621, workpiece diameter (max.): 360 mm, Equipped with: Gear Spindle Runout: -Radial (Bore): .00005 -Axial (Face): .00005 Pinion Spindle Runout: -Radial (Bore): .00005 Axial (Face): .00005 Axis Repeatability: -X: .0001 -Y: .0001 -Z: .0001 Axis Lost Motion: -X: .00005 -Y: .00005 -Z: .00005 Fanuc 160I MB Control Base Work Holding Draw Bars Automatic Doors Spindle Chiller Transformer Hydraulic System Festo Pneumatics Automation Interface Available SPECIFICATIONS: Maximum Gear Outside Diameter: 360 mm (14.2") Maximum Pinion Outside Diameter: 340 mm (13.4") Maximum Pinion Drive Speed: 3000 rpm Maximum Gear Drive Speed: 1500 rpm Offset Vertical 150 mm ( 5.9") Pinion Cone Range: (90) (135-350) (70) (146-438)* (110) (51-343)* Gear Cone Range: (90) (65-280) (70) (78-306)* (110) (56-284)* Standard Testing Torque Load 2 to 90 Nm (1.5 to 66 ft-lb). Parallel Axis - face-to-face 147 - 362 - Center Distance -7 - 250 Pinion Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 419 mm (16.5") Hsdexdfanepfx Agzeg Gear Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 250 mm (9.8") Floor Space (width & length) 2100 x 2550 mm (82.7 x 100.4") Height (to top of stack light) 2750 mm (108.3") Weight (base machine) 9100 Kg (20062 lbs)

Condition: good (used), Year of construction: 2013, control Siemens 840D sl turning length 2000 mm turning speeds max. 3100 1/min Torque 1200 Nm diameter of quill 140 mm quill power 5-30 kN total power requirement 125 kW weight of the machine ca. 20 t The machine can still be inspected under power at the seller's factory. Hodpfxev Nw Npj Agzeg It is in good condition, the precision of the turning operation is very good. The milling drive is not functional. An offer from Niles for the repair of the milling drive is available on request. Hydraulic steady rest included. Technical details: Turning length 2000 mm Control Siemens 840 D sl Main spindle: Speed max.3800 1/min Main spindle: Torque max. 1200 Nm Pinole diameter 140 mm Center point MK6 Quill force 5 - 30 kN Feed speed Z-axis mm/min Rapid traverse Z-axis 40 m/min Feed rate X-axis - mm/min Rapid traverse X-axis 25 m/min Total power requirement 125 kW Machine weight approx. 20 tons

Condition: refurbished (used), Year of construction: 1985, functionality: fully functional, travel distance X-axis: 1,200 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 700 mm, spindle speed (max.): 1,500 rpm, spindle speed (min.): 5 rpm, feed length X-axis: 1,200 mm, feed length Y-axis: 2,000 mm, feed length Z-axis: 700 mm, feed rate X-axis: 1,000 m/min, feed rate Y-axis: 1,000 m/min, feed rate Z-axis: 1,000 m/min, total width: 4,000 mm, San Rocco Horizontal Boring Machine Hodpfx Asx Rhlcsgzjg Fully overhauled San Rocco horizontal boring machine, originating from a high-end aerospace manufacturing facility. The machine is equipped with a Siemens SINUMERIK 840D CNC control system with SIMODRIVE 611 drive technology. The machine is fitted with modern digital drive systems and is designed for high-precision multi-axis machining in continuous operation. It was fully overhauled in 2024, including brand-new telescopic covers on all axes, as well as numerous additional essential refurbishments to the hydraulic system, CNC components, hoses, seals, and related assemblies. Travels X-axis (longitudinal): 1,200 mm Y-axis (cross): 2,000 mm Z-axis (vertical / spindle axis): 700 mm Spindle Data Boring spindle diameter: 100 mm Tool interface: ISO 50 Milling spindle diameter: 185 mm Spindle axial travel: 700 mm Feeds and Rapid Traverses Automatic feeds (spindle and vertical axis): 2 × 1,000 mm/min Rapid traverse (spindle and vertical axis): 5,500 mm/min Distances Minimum spindle height above table: 0 mm Maximum spindle height above table: 1,500 mm Maximum distance from spindle nose to table center: 1,850 mm Spindle Speeds Torque range: 5 to 14 rpm Continuous power range: 15 to 1,450 rpm Number of gearbox ranges: 4 Speed ranges: 6–51 / 49–160 / 140–460 / 440–1,450 rpm Table Data Rotary table size: 1,100 × 1,300 mm Longitudinal travel: 1,200 mm Cross travel: 2,000 mm Table Feeds Automatic feeds X and Y: 1,000 mm/min Rapid traverse X and Y: 5,500 mm/min Table Rotation Continuous rotation: 30 to 100 degrees per minute Rapid rotation: 5,000 degrees per minute Drive System Siemens SIMODRIVE 611 E/R module 36/47 kW LT modules 108 A and 2 × 25 A Lifting and Transport Data Group 1 Steel bar Ø 70 mm, length 1,600 mm Steel bar Ø 70 mm, length 2,400 mm Four spacer rings for lifting slings Four steel slings Ø 22 mm Weight approx. 12,500 kg Group 2 Two steel slings, minimum Ø 18 mm Weight approx. 3,500 kg Group 3 Manual lifting Weight approx. 1,300 kg Condition The machine is in very good technical condition and can be inspected and tested under power by appointment.

Condition: excellent (used), Year of construction: 1999, CNC Lathe MAZAK SQT 200 MS Year of manufacture: 1999 Including indicated tools and sub-spindle Control: Mazatrol PC Fusion CNC 640T Technical specifications: Max. swing diameter: 525 mm Max. swing diameter over saddle: 350 mm Max. turning diameter: 300 mm Bar work up to max. diameter: 51 mm Main spindle: Speed range: 35 – 4,000 rpm Main drive power: 15 kW Max. torque: 350 Nm Spindle nose: A2 – 6 inch Spindle bore: 61 mm Spindle positioning C-axis: 0° - 360°/0.001° Second spindle: Speed range: 35 – 5,000 rpm Drive power: 7.5 kW Max. torque: 57 Nm Indexing: 72 positions/5° Tool turret: Number of tool stations: 12 (freely configurable with stationary and driven tools) Turret indexing time – 1st station: approx. 0.2 s Driven tools: Drive power: 3.7 kW Max. torque: 35 Nm Speed range: 25 – 4,500 rpm Travel: Turret travel: X-axis: 190 mm Z-axis: 575 mm B-axis: 585 mm Rapid traverse: X-axis: 30 m/min Z-axis: 30 m/min B-axis: 18 m/min Hsdpfx Asx Hgl Hogzog Feed range: X/Z-axis: 0 – 5,000 mm/min C-axis: 1 – 2,000°/min

Condition: ready for operation (used), chuck outer diameter: 700 mm, total height: 3,415 mm, controller model: Siemens 840D Solution Line, empty load weight: 17,000 kg, Type: Ultrix 800 RT The Ultrix 800 RT is a multifunction machining center with 5 interpolated axes and a moving gantry for high-speed milling, turning, grinding, drilling, tapping, finishing, deburring, and roughing of complex parts. When used for turning vertical lathe: - swivel range: 1100 mm - maximum weight of the workpiece: 700 kg - 40/30 kW on the table - max. torque on the table: 1500 Nm - maximum speed of the table: 1000 rpm !! - hydraulic clamping on table - tool taper for turning: KM63 - 18 000 rpm - HSK 63 - 150-position tool changer with 24 tool positions for turning When used for milling, grinding, drilling, ... machining center: - X-axis: 800 mm - Y-axis: 900 mm - Z-axis: 600 mm - A-axis: -30° / 110° - C-axis: continuous - maximum weight of the workpiece: 700 kg - 55/40 kW on spindle - max. torque on the spindle: 22 Nm - max 40,000 rpm - tool taper for milling: HSK-E40 - 150-position tool changer with 126 tool positions for milling, grinding, drilling Hedpfx Agextgkaozeg List of options mounted on the machine: 1 - 40,000 rpm high-speed spindle 2 - table dia 700 mm with hydraulic clamping 3-150-position tool changer 4 - chip conveyor belt 5 - cooling system with recovery 6 - coolant temperature control 7 - high pressure cooling (40 to 70 bar) by spindle 8 - smoke extraction system 9 - chip collection box 10 - Presetting system and tool integrity: laser and mechanical probe for measuring tools 11 - Renishaw probe Max turningdia -- passage: 1100 mm Power on the spindle: 40/30 kW Long: 4655 mm Wide: 5890 mm Turret: yes Qty Tools: 150 positions Coolant pump: yes

Condition: used, Year of construction: 2010, Technical details: x-travel: 6500/13500 mm y-travel: 4000 mm z-travel: 1500 mm w-axis: 2250 mm table surface area: 5500/12500 x 3000 mm max. workpiece weight: 50.000/75.000 kg ram head dimension: 520 x 625 mm Hodoway I Uopfx Agzog milling spindle motor: 67,4 ( s1/100% ) kW max. torque on the spindle: 2900 Nm tool taper: DIN 69893 HSK-A 100 milling head speed: 1 - 1000 / 5 - 5000 U/min feed speeds: 1 - 24000 mm/min w-axis: 1 - 6000 mm/min. distance between columns: 3500 mm passage: 3000 mm total power requirement: 120 kW weight of the machine ca.: 250 t dimensions of the machine ca.: 29,5 x 9,5 x 8,2 m with CNC SIEMENS 840 D autom. tool magazine for 212 tool stations autom. milling head magazine for 6 milling heads 1 milling head -straight- 67 kW, 2900 Nm, 5000 rpm, HSK-A 100 2 milling head -straight extended- 40 kW, 1700 Nm, 5000 rpm, HSK-A 100 3 milling head -angular head extended- 40kW, 4000 rpm, 1800 Nm, HSK-A 100 4 milling head -angular head - 67 kW, 4000 rpm, 2900 Nm, 360 x 1°, HSK-A 100 5 milling head -angular head - 67 kW, 4000 rpm, 2900 Nm, 360 x 1°, HSK-A 100 6 milling head -universal Index head - 40 kW, 4000 rpm, 2100 Nm, C-axis 360 x 1°, B-axis +/- 110 x 1°, HSK-A 100 coolant attachment, chip conveyor *

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Hedpsrtrzdjfx Agzsg Depth of Taper: 8" Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Condition: good (used), Year of construction: 2007, max. wheel diameter 500 mm gear width 200-400 mm module 12 turning speeds 0-3250 U/min bracke pressure bis max. 95 Nm inner taper Konus #39 Control Fanuc 16 Hsdpfx Agjvr Hf Eezjg total power requirement 15 kW weight of the machine ca. 6 t dimensions of the machine ca. 2.350 x 2.240 x 2.500 mm HIGHLY FLEXIBLE TESTING OF HARD, FINISHED AND GREEN SPIRAL BEVEL AND HYPOID GEAR SETS The T 60 bevel gear testing machine is a CNC testing machine with three linear axes for the fully automatic hard and soft testing of spiral bevel and hypoid gear sets with a 90° axis angle. It offers versatile objective and subjective testing options with speeds up to 3,250 min and braking torques up to max. 95 Nm.

Condition: good (used), DECKEL Milling Machine, Tool Milling Machine DMU 35 M 3 x 2-axis CNC milling machine With SIEMENS 810 D – ShopMill software Year of manufacture: 2001-2003 Travel distances X/Y/Z: 350 x 240 x 340 mm Infinitely variable spindle speed: 20 – 6,300 rpm Spindle taper: SK 40 DIN 69871 Drawbar: DIN 69872 Drive power: 6.3 / 10 kW (100/40% duty cycle) Torque: 55/80 Nm max. Universal swivel/rotary table: 400 x 290 mm Table load capacity: 100 kg Distance spindle nose to table: min./max. 145/485 mm Feed rates: 3,000 mm/min Rapid traverse: 5,000 mm/min Input increment: 0.01 mm Rotation range: 360 degrees Swivel range: degrees Total power requirement: kVA Weight: approx. 1,750 kg Technical data subject to change! Equipment / Accessories: Direct position measuring system for 3 axes Spindle drive via servo motor with toothed belt 2 gearbox stages Full safety enclosure with sliding door Swiveling control panel Coolant nozzles on vertical head Coolant system Chip tray with coolant tank Electronic handwheel Machine feet Machine lamp Interface Serial RS232C, LAN (RJ45) Hodpfx Agjxz Rdaszsg The machine is perfect for prototyping, toolmaking, training, mechanical workshops, gunsmiths, etc. It impresses with its versatility, with the additional manually operated rotary-swivel table allowing 5-sided machining. Available in March 2026 A total of 3 machines are available. Condition: Good to very good from a vocational training center, see pictures

Condition: excellent (used), Year of construction: 2000, CNC Lathe MAZAK SUPER QUICK TURN 200 Year of manufacture: 2000 Working area: Max. swing diameter: 525 mm Max. turning diameter: 350 mm Max. turning length: 514 mm Bar work up to max. diameter: 51 mm Main spindle: Speed range: 35 – 5,000 rpm Main drive power: 18.5 kW Constant torque: 333 Nm Spindle nose: A2 – 6 inch Spindle bore: 61 mm Turret: Standard version: 12 stations Travel: Turret travel: X-axis: 190 mm Z-axis: 535 mm Hedpfxsxvb E De Agzjg

Condition: used, Technical details: x-travel: 6500/13150 mm y-travel: 4000 mm z-travel: 1250 mm w-axis: 2250 mm table surface area: 5500/12150 x 3000 mm max. workpiece weight: 70.000/105.000 kg Hsdpfjwc A Shex Agzjg ram head dimension: 480 x 510 mm milling spindle motor: 63 kW max. torque on the spindle: 3300 Nm tool taper: DIN 39871 AD ISO 50 milling head speed: 6,3 - 4000 U/min feed speeds: 1 - 24000 mm/min w-axis: 1 - 6000 mm/min. distance between columns: 3500 mm passage: 3000 mm total power requirement: 120 kW weight of the machine ca.: 245 t dimensions of the machine ca.: 29,0 x 7,7 x 8,1 m The machine is in mint condition and was generally overhauled in 2020! with CNC SIEMENS 840 D autom. tool magazine for 153 tool stations autom. milling head magazine for 6 heads milling heads - straight - straight extended length - milling head -angular head standard - 4000 rpm, 144 x 2,5°, ISO 50 milling head -angular small extended length -40 kW, 4000 rpm, 1800 Nm, 144 x 2,5°, ISO 50 milling head -universal index - 40 kW, 4000 rpm, 2100 Nm, C-axis 144 x 2,5° , B-axis +/- 44 x 2,5°, ISO 50 coolant attachment, chip conveyor *

Condition: good (used), Year of construction: 2019, machine/vehicle number: 25728, Equipped with: Hydraulic Unit Sinumerik 840D sl CNC Control Slim Line Operator Panel OP012 W/12 TFT-Color Display 19" Machine Control Panel 20 Tool ATC CAPTO C6 Multifunctional Tool Carrier For Turning and Driven Tools One Fixed Tool Unit Assembled To The Compound Slide W/Coolant Thru The Turning And Drilling Tools, Coolant For The Driven Spindle From The Outside Drilling Spindle Additional Drill Spindle For Orientation Chip Conveyor Coolant Equipment -Including piping and shut-off valve and flow control switch -To supply coolant to tools for coolant and flushing through the cutting tools -To supply coolant for flushing the work piece and chuck -To supply coolant for flushing the working area Paper Band Filter Immersion Cooler High Pressure Coolant Pump, 40 Bar Through Tools Flushing Pistol, Hand Held Air Cleaner - Mechanical Separation "Mist Collector" Tool Life Display Remote Diagnostics Signal Lamp Automatic Door For Loading W/Shuttle Load and Unload Shuttle Swivel Loader Automation Cell Tuned for Part Pallet Conveyor For 20 Raw And Finished Parts Pallets Pallets Designed for Part 596500 Handling System SPC Station (Maximum O 270 mm, Maximum H 150 mm, Maximum Wt. 12 kg) NIO Station (Closing forward leading gravity) Skiving Software (Hardware: Software and user surfaces for skiving technology) Measuring Probe (For measuring diameters and length of the workpiece in the machine) Measuring Software for Teeth Measuring (MDK and Flank Line, Software and User) Measuring Program (Automatically measuring program for measure the position of the two gears to each other, after using sister tools) SPC (Every X workpieces the MDK needs to be measured) Tool Changer (Precut, measurer and final cut) Skiving Tool Identification (Hardware, software for the identification of the skiving tool after tool change) Hydraulic Diagrams Coolant Diagrams Lubrication Diagrams Electrical Wiring Diagrams Hardcopy of Diagrams CF Certificates Specifications: Workpiece Spindle: -Speed: 0-7000 l/min -Power: 55,2 - 59,7 kW Tool: Capco C6 Tool Spindle: -Speed: 0-6000 l/min -Power: 29 - 41 kW Machine Weight, Floor Space and Voltage Supply: -Operating Voltage: 400V, 3 Phases, 50 Hz -Control Voltage: 24 V -Lighting Voltage: 240 V, 50 Hz -Floor Space: 2,700 x 2,600 mm -Height: 4,000 mm -Total Weight, Approximate: 16,000 kg Longitudinal, Z-Axis: -Stroke: 800 mm -Rapid Rate: 24 m/min -Feed Force: 12 kN Transverse, X-Axis: -Stroke: 900 mm Hedpfew Iqumjx Agzeg -Rapid Rate: 24 m/min -Feed Force: 12 kN Tool Spindle, B-Axis: -Range: -20 / +90 Degree Y-Axis for Spindle Unit: -Stroke: 200 mm -Rapid Rate: 12 m/min -Feed Force: 6 kN C-Axis Main Spindle: -Positioning Accurace: 9" Multifunctional Tool Carrier: -Power: 29 kW at 100% ED -Power: 41 kW at 44% ED -Torque: 141 Nm at 100% ED -Torque: 212 Nm at 44% ED -Spindle Speed: 0-6000 min-1 -B-Axis for Stepless Motion in a Range Of: -20/+90 Degree Tool Magazine: -Maximum Tool Diameter: 100 mm -Approximate Tool Length: 300 mm -Approximate Tool Weight: 12 kg Swivel Loader: -Maximum Workpiece Diameter: 270 mm -Height: 150 mm -Weight: 16 kg

Condition: excellent (used), Cycle Lathe Weiler E 50 / 1D Year of manufacture: 1999 Machine no.: 684 Control: Weiler (Siemens 810D) Power-on hours: 43,543h (Machine was overhauled by Schmeißer a few years ago) Technical specifications: Spindle speed: 1–625 / 4–2,500 rpm (2 gear stages) Drive power: 17kW torque Spindle torque: 1,200Nm Hsdpswtqnrsfx Agzeg Spindle bore: 66mm Distance between centers: 1,000mm Center height: 280mm Swing diameter over bed: 570mm Swing diameter over cross slide: 340mm Equipment/Accessories: - Interface for external programming - Parat tool holder incl. 6 holders - Operating manual - Coolant system - Various turning tools and drills - Jaws for lathe chuck - Live center - Machine feet The machine has been tested under power and is in perfect, ready-to-use condition. The machine bed is also in good condition. Price: net ex works, loaded on truck from stock.

Condition: excellent (used), Year of construction: 2006, 5-axis CNC machining center 2006 Control: Heidenhain iTNC 530 Technical data: x-axis travel 880 mm y-axis travel 630 mm z-axis travel 630 mm Max. torque 130 Nm tool holder SK 40 (ISO 7388IIB) swiveling B: 103° Work table: Clamping surface 1,250 x 700 mm Rotary table diameter 700 mm rotatable C: 360 ° Max. table load approx. 500 kg T-slots 11x 14mm x 63mm Tool magazine: Number of tool places 32 (2x 16) pos. tool holder SK 40 (ISO 7388IIB) Max. tool diameter 80 / 130 mm Max. tool diameter with free neighbor box 160 mm Max. tool length 315 mm Hodpewn A Slefx Agzeg Max. tool weight 8.0 kg

Condition: excellent (used), EMCO Precision Lathe EMCOMAT 17 D Incl. 3-axis EMCO digital display Year of manufacture: 2007, with CE marking 2 units available! Centre distance: 700 mm Centre height: 170 mm Swing over bed diameter: 340 mm Swing over cross slide diameter: 190 mm Bed width: 260 mm Longitudinal slide travel: 600 mm Cross slide travel: 220 mm Top slide travel: 110 mm Cross slide length: 410 mm Cross slide width: 150 mm Bed carriage guide length: 380 mm Tool cross-section: 20 x 20 mm Distance spindle centre – top slide: 34 mm Top slide (compound rest) swivelling range: 60 / 120° Headstock: Spindle mount: DIN 55029 (Camlock) Spindle bore: 50 mm Internal taper to DIN 7178 1:22 Spindle diameter in front bearing: 70 mm Max. chuck diameter: 200 mm Max. face plate diameter: 200 mm Spindle speed: 40 – 3000 rpm Stepless speed control Mechanical speed ranges: 4 Main Drive: Power at 40% duty cycle: 5.3 kW Max. rated torque at main spindle: 640 Nm Feed: 20 (28) longitudinal feeds Z: 0.045–0.787 mm/rev 20 (28) cross feeds X: 0.023–0.406 mm/rev Threads: 20 (28) metric threads (basic equipment): 0.4 – 7.0 mm Tailstock: Hodsxx S R Ajpfx Agzsg Quill diameter: 50 mm Quill taper: MK 3 Quill stroke: 120 mm Lateral adjustment: ±13 mm Permissible workpiece weight (between centres): 50 kg, supported by tailstock: 150 kg Weight: 755 kg Dimensions: 1650 x 1060 x 1635 mm The EMCOMAT 17 D is a precision lathe designed for all areas of mechanical engineering and for training purposes. Equipment: • EMCO 3-axis digital display with colour screen • Potentiometer, EMERGENCY STOP button, digital speed display on control panel next to digital display • 3-jaw chuck • MULTIFIX toolpost head, size B • Electrically interlocked chuck guard • Quick-change collet device • MICROJET coolant spray device • Chip guard rear panel • Machine light • Machine feet • Bed stop Condition: Very good, from a training centre "Due to its quality and price, the machine is not suitable for private individuals." Available from March 2026

Condition: excellent (used), Year of construction: 2002, CNC Turning-Milling Center GILDEMEISTER TWIN 500 Linear Year of manufacture: 2002 Siemens control system Technical data: Swing diameter: 610 mm Turning diameter: 610 mm Turning length: 1870 mm Drive power: 69 kW Spindle speed: 3,200 rpm C-axis torque: 650 Nm Main spindle - left Chuck diameter: 250–500 mm Max. bar diameter: 102 mm Upper slide Hsdpsw Tarfefx Agzsg Rapid traverse speed X/Y/Z: 45/24/70 m/min Slide travel X1/Y1605 / 105 mm Turning/milling spindle HSK 63A Max. spindle speed: 12,000 rpm B axis Swivel range B1: 120° Resolution: 0.001° Tool magazine Number of tools: 40 Tool length / Max. quantity: 350/40 mm

Condition: excellent (used), Year of construction: 2004, We are offering an exceptionally high-quality precision lathe. Within its class, this is likely the best German lathe ever built. BOEHRINGER Precision Lathe Model DUE 500 Year of manufacture: 2004, including CE certification and central lubrication Machine No.: T1022.2027-00 Center height: 240 mm Swing diameter over bed: 500 mm Swing diameter over cross slide: 285 mm Center distance: approx. 1,200 mm Effective turning length: approx. 1,000 mm Bar capacity: 62 mm Spindle nose: DIN 55027 Size 6 Hodpfx Ajw Rdthjgzsg Spindle bore: 100 mm Drive power: 11 kW Maximum torque: 2,000 Nm 24 spindle speeds: 11.2 – 2,240 rpm 60 cross feeds: 0.03 – 28 mm/rev 60 longitudinal feeds: 0.06 – 56 mm/rev Tailstock quill stroke: 190 mm Tailstock taper: MK 5 Machine footprint (LxW): approx. 4,000 x 1,525 mm Weight: approx. 4,300 kg Accessories: - HEIDENHAIN 3-axis digital readout - Central lubrication system - Electrically interlocked chuck guard - Coolant system - Chip protection rear panel - Röhm chuck, T 250 mm, with various jaws - Telescopic cover for lead and feed screw, support to bed - Machine lamp - Multifix C + 4 quick-change tool holders - Live center - Operating manual - Circuit diagram - Rapid traverse in longitudinal and cross slides Condition: The machine is in very good technical and visual condition. Backlash on cross slide approx. 0.3 mm, on compound slide approx. 0.15 mm Spindle nose runout approx. 0.006 mm Bed geometry: deviation approx. 0.01 mm over approx. 750 mm bed length (measured on flat guideway towards chuck using dial indicator) The following parts have been renewed: - Oil change - New hoses for central lubrication - New wipers - Key for operating lever replaced - Locking pin for interlock replaced Price is net, ex stock, loaded free of charge. Delivery by company truck can be arranged at extra cost.

Condition: excellent (used), Year of construction: 2002, 5-Axis Machining Center - Universal DECKEL MAHO DMU 70 EVO Year of manufacture: 2002 Control: MillPlus iT Heidenhain Machine hours: 33,289.6 h Spindle hours: 10,533.5 h Technical Data: X-axis travel: 750 mm Y-axis travel: 600 mm Z-axis travel: 520 mm Main Spindle: Speed range - main spindle: 20 - 18,000 rpm Drive power - main spindle: 35 / 25 kW Max. torque: 130 / 87 Nm NC Rotary Swivel Table: Clamping surface: 700 x 500 mm Swivel range, B-axis: 180° Rotatable, C-axis: 360° Max. table load: 350 kg Centering bore: 30 H6 mm T-slots: 7x 14H7 x 63 mm Table speed range: 21.5 rpm Hodsxf Hlhspfx Agzjg Tool Magazine: Number of tool positions: 32 Max. tool length: 315 mm Max. tool diameter: 105 mm Max. tool diameter with adjacent pockets empty: 130 mm Max. tool weight: 6 kg

Condition: reconditioned (used), We are offering an exceptionally good precision lathe. The machine is probably the best German lathe that has been built in this class. BOEHRINGER precision lathe model DUE 800 Year of manufacture: 1984 Order no.: 04041.01-807 Center height: 400 mm Circulation diameter over bed: 820 mm Circulation diameter over facing slide: 515 mm Center width: approx. 2200 mm Effective turning length: approx. 2000 mm Bar passage: 128 mm Spindle head DIN55022 size 11 Drive power: 30 kW Max. Torque: 6300 Nm 24 Speeds: 7.1 - 1400 rpm 60 face feeds: 0.05 - 28 mm/rev 60 longitudinal feeds: 0.06 - 56 mm/rev Rapid traverse in longitudinal cross feed Hedpfxsrt T S Rj Agzog Motorized top support Tailstock quill stroke: 280 mm Tailstock taper: MK 6 Space requirement: LxWxH approx. 6700x2500x2250mm Weight: approx. 7500 kg Accessories: 3-axis digital readout HEIDENHAIN Coolant device; chip protection rear panel, power chuck autoblock 500 mm with clamping jaws, roller conveyor cover for lead screw support to bed, machine light, chip conveyor, Parat basic holder incl. 11 holders, suction unit, 3-jaw steady rest with roller inserts (moving), emergency stop, chuck key, moving center point, operating instructions Condition: The machine is in very good technical and optical condition. Backlash in the top slide 0.1 mm and face slide 0.15 mm The geometry of the machine is also very good (was checked with a dial gauge) Measured on the flat track guide with dial gauge in the direction of the lathe chuck Bed wiper replaced, gearbox input shaft axial play compensated and bearings replaced, drive pins on motor/gearbox side replaced, shaft seals on lock case replaced, various bearings replaced The machine can be demonstrated under power. Functional videos can also be sent on request.