Used Undercut for sale (32)

Condition: good (used), Year of construction: 1999, functionality: fully functional, machine/vehicle number: 1877, cutting height (max.): 300 mm, total length: 18,500 mm, total height: 2,550 mm, cutting width (max.): 450 mm, total width: 2,400 mm, control cabinet width: 400 mm, saw blade diameter: 735 mm, overall weight: 11,000 kg, control cabinet length: 1,600 mm, control cabinet height: 2,400 mm, power: 15 kW (20.39 HP), type of input current: three-phase, Equipment: safety light barrier, Equipment: 01_ Cross-sections 20 x 60 to 300 x 450 mm 02_ Feed conveyor, transverse, 5 strands, 2.2 m 03_ Undercutting miter saw 04_ Universal milling machine ----> Roller cutter ----> Finger cutter 05_ Combination support for vertically operating tools ----> 1x Drilling machine ----> 1x Finger milling machine 06_ Combination support for horizontally operating tools ----> 2x Drilling machine ----> 1x Grooving machine 07_ Beam turning station, fully automatic Machine installation: 08_ Substrate, foundation: ----> The floor slab must have a thickness of at least 10 cm (with corresponding good reinforcement) This should be level and suitable for anchoring. 09_ Power requirements, type, quality, quantity: 09.1_ Electrical: ----> Voltage: 400/230V, 3/N/PE ----> Fuse rating: 3 x 63A ----> Frequency: 50 Hz ----> Peak demand: 15 kW The mains voltage must be constant and uninterrupted within the specified tolerance range! 09.2_ Compressed air: Fedpezv Tt Hjfx Al Ujpn ----> Flow rate: V < 600 l/min ----> Pressure: Operating pressure p = 8.5 bar; Maximum permissible pressure p = 10 bar Important: The control system was converted by Hundegger from MIPPS to CAN control in the fall of 2020!!

Condition: like new (used), Year of construction: 2024, Technical specifications: - Motor power 2.2 kW S1 - Max. Saw blade diameter: 350 mm - Saw blade holder: 30 mm Fjdpfx Alsfhbuyo Ujpn - Cutting time per stroke: 1.5 sec. - Speed ​​on the saw shaft: 3800 rpm - Air consumption per cycle: 5 L - Working table height: 900 mm - Extraction nozzle: 2x100 mm - Operating pressure: 7-8 bar - Net weight: approx. 200 kg - Required air flow 1000 m³ / h - Voltage: 400 V / 50 Hz 3-phase - Cutting capacity in mm: 45 x 230 60 x 210 90 x 180 100 x 125 Standard basic equipment: - Saw blade feed pneumatic drive - Automatic engine brake - Set of operating keys - Emergency stop push button - Speed ​​control for saw blade feed - Fixed vertical protection device - Upper safety pressure device (pneumatic protective hood) - Suction speed at least 28m / sec. - Colors: basic stand light gray RAL 7035, doors telegrey RAL 7046, protective shield and protective hood zinc yellow RAL 1018

Condition: used, Year of construction: 2000, operating hours: 3,273 h, machine/vehicle number: 15015702974, travel distance X-axis: 710 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 520 mm, torque: 130 Nm, controller manufacturer: Heidenhain 426/430, workpiece weight (max.): 350 kg, total height: 2,724 mm, total length: 2,756 mm, total width: 2,020 mm, table width: 500 mm, table length: 700 mm, rotary table diameter: 700 mm, overall weight: 5,500 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 15,000 W, number of spindles: 1, number of slots in tool magazine: 32, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, 5-Axis Machining Center DECKEL MAHO DMU 70V We offer for sale an advanced, universal vertical machining center, the Deckel Maho DMU 70V (part of the renowned DMG MORI group), equipped with a numerically controlled (NC) rotary/tilting table. The machine features a compact and robust design, minimizing its footprint in the production hall while offering full capabilities for advanced 5-axis machining. AXIS SPECIFICATIONS AND WORKING AREA Fpodpfxezumh Io Al Uen • Axis travel (XYZ): X = 710 mm | Y = 520 mm | Z = 520 mm • Working travel: 710 mm (X) / 520 mm (Y) / 520 mm (Z) INNOVATIVE NC ROTARY/TILTING TABLE (4th and 5th AXIS) • Mounting surface dimensions: ∅ 700 mm x 500 mm (practical design with factory-cut sides, facilitating optimal mounting of vises and fixtures) • Maximum table load: 350 kg (full mechanical safety of the gearbox, bearings, and measuring system) • Axis rotation range: • C-axis (rotation): continuous / multi-rotation operation (advanced trochoidal milling strategies) • B-axis (tilting): wide working range of over 180°, providing excellent access to the workpiece and freedom for angled undercutting MAIN DRIVE AND SPINDLE • Spindle speed: continuously (steplessly) adjustable in the range of 20 – 12,000 rpm • Spindle power: 15 kW • Maximum torque: up to 130 Nm (powerful cutting force guaranteeing excellent stiffness and stability during heavy rough machining of hard materials) CONTROL SYSTEM AND TOOL MAGAZINE • Control system: Reliable and widely appreciated by operators, the Heidenhain 426/430 (simple dialog programming, intuitive menu) • Tool magazine: Automatic, compact chain-type magazine with a capacity of 32 positions (fast tool change in automatic cycles) LOGISTICAL AND CONNECTION PARAMETERS • Overall dimensions of the machine ready for operation (with chip conveyor): • Length: 2756 mm • Width: 2020 mm • Transport height: 2724 mm (the machine fits easily on standard trailers and passes through conventional hall doors) • Total machine weight: approx. 5,500 kg • Maximum power consumption (connection): up to 42 kVA • Input voltage: 400 V (AC - three-phase current) • Current protection (fuse): 63 A • Power supply frequency: 50/60 Hz MACHINE CONDITION AND ADDITIONAL INFORMATION The machine is in good technical condition, regularly serviced and maintained. It is ideally suited for both serial production and tool shops producing complex molds, dies, and precise 5-axis parts. The machine comes complete with a chip conveyor.

Condition: ready for operation (used), Year of construction: 1990, MARKON Log house drilling machine with undercutter year 1990 manufacture Markon Lathi / Finland Length = 3550mm Width= 1500mm Height= 2910mm Engine power Drilling unit: 6 x 3 kW moulder: 1 x 5.5 kW Dimensions of the log to be pushed Height max 250mm Height min 130mm Width max 250mm Width min 60mm Length min 600mm Tool sizes and speeds Drill max diameter 40 mm Moulder max diameter 250 mm Drill length 325 mm Drill mounting arm diameter 20h7 mm Drill rotation speed 2880 rpm Moulder: Fpedpfx Ajfw Rt Rjl Uen rotation speed 2880 rpm AIR Suction openings dia. 160 mm 2 suction openings Drill unit suction opening diameter 90 mm Suction openings 6 pcs Air speed at the suction opening 30 m / s Air consumption 8460 m3 / h electrical connection Total power 380 V 24 kW Compressed air connection Minimum pressure 6 bar Drilling unit air demand / stroke "48 1 Total air demand ~ 2200 1 / min incl. 3,5 meter roller conveyor + 12 drillings

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, travel distance X-axis: 4,000 mm, travel distance Y-axis: 2,200 mm, travel distance Z-axis: 1,100 mm, table length: 4,500 mm, table width: 2,500 mm, spindle speed (max.): 22,000 rpm, CNC Heidenhain iTNC 640 WORKING AREA: Longitudinal X-axis travel: mm 4.000 Transversal Y-axis travel: mm 2.200 Vertical Z-axis travel: mm 1.100 Maximum speed with interpolating axes: m/min 50 WORKTABLE: Dimensions: mm 4.500 x 2.500 Height: mm 300 Load capacity: T/m² 15 T-slots for workpiece clamping mm 28 DIN 650 (H12), complete with leveling elements. T-slot direction parallel to Y-axis movement. CONTINUOUS POSITIONING UNIVERSAL HEAD WITH ELECTROSPINDLE: Automatic universal head indexed to 360,000 positions (every 0.001°). Rotation is driven by direct drive motors and controlled by the CNC as a positioning axis. Automatic tool clamping. Allows 10° undercut machining. Internal cooling system for bearings and axis motors. C-axis rotation range: ± 270° A-axis rotation range: ± 185° Maximum axis rotation speed: rpm 30 Maximum torque available on A/C axes: Nm 450 Axis clamping torque: Nm 1.400 Spindle power (S1/S6): kW 22/33 Spindle torque (S1/S6): Nm 84/128 Maximum spindle speed: rpm 22.000 Constant power range: rpm 3.000 to 18.000 Constant torque range: rpm 10 to 3.000 Tool interface: HSK-A63 DIN 69893 ELECTROSPINDLE HSK-A100 WITH SEMI-AUTOMATIC CHANGE SYSTEM Spindle power (S1/S6): kW 37/43 Spindle torque (S1/S6): Nm 140/165 Maximum spindle speed: rpm 15.000 Constant power range: rpm 2.500 to 12.000 Constant torque range: rpm 10 to 2.500 Tool interface: HSK-A100 DIN 69893 CHAIN TOOL MAGAZINE – 55 POSITIONS, HSK-A100 / HSK-A63 Floor-mounted fixed chain magazine located at the rear of the machine, fully enclosed for operator protection, equipped with a vertical tool change arm and automatic tool pre-selection. Fixed-pocket management system. Hydraulic axis locking Total tools: No. 55 HSK-A63 tools (DIN 69893): Number of tools: No. 30 Max tool diameter: mm 90 Max tool diameter (with adjacent pockets free): mm 160 Max tool length: mm 300 Max tool weight: kg 10 HSK-A100 tools (DIN 69893): Number of tools: No. 25 Max tool diameter: mm 100 Max tool diameter (with adjacent pockets free): mm 160 Max tool length: mm 450 Max tool weight: kg 20 REQUIRED CONNECTIONS Fpsdpfoyv In Iox Al Uen Maximum installed power: kVA 177 Maximum current required: A 235 MACHINE EQUIPPED WITH: • Heidenhain HR550 remote electronic handwheel • High-pressure water and air through the spindle • Semi-automatic electrospindle change system with HSK-A63 and HSK-A100 interfaces • Various tooling included with the machine • Renishaw probe • BLUM laser presetting system • AUTOCAL automatic head calibration system • Visormax subscription for remote monitoring • Electrical cabinet air conditioning unit • Cooling system for all axes and the electrospindle • User and maintenance manual and CE declaration of conformity

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, travel distance X-axis: 4,000 mm, travel distance Y-axis: 2,200 mm, travel distance Z-axis: 1,100 mm, feed rate X-axis: 50 m/min, feed rate Y-axis: 50 m/min, feed rate Z-axis: 50 m/min, table length: 4,000 mm, table width: 2,000 mm, spindle speed (max.): 22,000 rpm, torque: 128 Nm, spindle nose: 63, CNC Heidenhain iTNC 530 S.P. WORKING AREA Longitudinal X-axis travel: mm 4.000 Transversal Y-axis travel: mm 2.200 Vertical Z-axis travel: mm 1.100 Maximum speed with interpolating axes: m/min 50 WORKTABLE Dimensions: mm 4.000 x 2.000 Height: mm 300 Load capacity: T/m² 15 T-slots for workpiece clamping mm 28 DIN 650 (H12), complete with leveling elements. T-slot direction parallel to X-axis movement. AXIS CHARACTERISTICS Axis feed rate: mm/min 50.000 Acceleration: m/s² 4 WORKING AREA (CLEARANCES) Maximum horizontal clearance: mm 3.200 Maximum vertical clearance under crossbeam: mm 1.926 Height of worktable from floor: mm 330 CONTINUOUS POSITIONING UNIVERSAL HEAD WITH ELECTROSPINDLE Automatic universal head indexed to 360,000 positions (every 0.001°). Rotation is driven by direct drive motors and controlled by the CNC as a positioning axis. Automatic tool clamping. Allows 10° undercut machining. Internal cooling system for bearings and axis motors. B-axis rotation range: ± 185° A-axis rotation range: ± 185° Maximum axis rotation speed: rpm 30 Maximum torque available on A/C axes: Nm 450 Axis clamping torque: Nm 1.400 Spindle power (S1/S6): kW 22/33 Spindle torque (S1/S6): Nm 84/128 Maximum spindle speed: rpm 22.000 Tool interface: HSK-A63 DIN 69893 The head is supplied complete with a cradle for handling and storage. The cradle is used outside the working area and therefore does not reduce the machine’s actual working capacity. CHAIN TOOL MAGAZINE – 30 POSITIONS (HSK) 30-position automatic chain tool changer located at the rear side of the working area, fully protected from dust and chips. Tool type: HSK-A63 DIN 69893 Max tool diameter (adjacent pockets occupied): mm 90 Max tool length: mm 300 Max tool weight: kg 10 MEASURING SCALE PRESSURIZATION Pneumatic system complete with control unit for pressurizing the measuring scales. SPRAY-MIST TOOL LUBRICATION/COOLING Mist lubrication system. The mist is generated by mixing air and oil and is controlled via M-function. The spray-mist improves cutting quality, prevents built-up edge formation, keeps the cutting area clean, and provides cooling. Highly effective for improving surface finish quality. EXTERNAL TOOL COOLING Coolant distribution system controlled by the CNC, with nozzles positioned on the flange around the spindle. Complete with a tank (1,200-liter capacity) for coolant collection and filtration. Flow rate: 30 l/min, pressure: 4 bar. REQUIRED CONNECTIONS Maximum installed power: kW 150 Maximum current required: A 235 MACHINE EQUIPPED WITH: • Heidenhain HR550 remote electronic handwheel • Various tooling included with the machine • Renishaw probe • BLUM laser presetting system • AUTOCAL automatic head calibration system • Visormax subscription for remote monitoring • Electrical cabinet air conditioning unit Fedpezb Evlsfx Al Uepn • Cooling system for all axes and the electrospindle • No. 2 chip conveyors positioned on both sides of the worktable • User and maintenance manual and CE declaration of conformity

Year of construction: 2025, operating hours: 210 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: VAUZ1973KZT03151, Liebherr Telescopic Handler T 33-10, Generation 6 For sale is a Liebherr telescopic handler T 33-10, originally owned, acquired as new from an authorized Liebherr dealer. Used exclusively in biogas and substrate logistics. Maintenance performed according to manufacturer specifications throughout, records available. ENGINE AND DRIVE - Deutz TCD 3.6 L4, 4-cylinder inline engine, water-cooled, turbocharger with intercooler - 105 kW / 143 hp, 3.6 l displacement, 500 Nm at 1,600 rpm - Emission stage EU V / Tier 4f, electronic common rail fuel injection - Hydrostatic closed-loop drive, infinitely variable - Permanent all-wheel drive, 45% limited-slip differential in the front axle - 3 electronically adjustable steering modes, full lock in 3.5 turns - 20 km/h, 41 kN traction force, reversible fan drive LIFTING AND WORKING HYDRAULICS - Max. load capacity 3,300 kg, lifting height 9,747 mm, reach 7,176 mm - Load capacity at max. lifting height 1,500 kg, at max. reach 300 kg - Working hydraulics 106 l/min, single-lever control via multi-function joystick - Lowering brake valves on lifting, tilting, and telescopic cylinders - Auxiliary work circuit on the telescopic head, adjustable flow rate - Hydraulic quick hitch Liebherr Compact and Stereo - Tilting kinematics 126.4°, telescopic cylinder with end-of-stroke damping CABIN - Elastomer mounting, integrated ROPS/FOPS structure internally - Tinted safety glazing front and roof, one-piece windshield wiper - Windshield washer system front and rear, rear window tilting - Driver's door with opening window, lockable when open - 3-stage fan with fresh air intake and filter - Steering column tilt adjustable via foot pedal, driver's seat with artificial leather upholstery SAFETY AND EQUIPMENT - Overload warning device EN 15000 with automatic shut-off, audible/visual - Hill start assist Auto Hill Assist, level adjustment via the front axle - Battery main switch with automatic battery disconnection - Air filter with automatic dust extraction - Central lubrication system, tool-free access to telescopic cylinder lubrication - Work spotlights 2x front, 2x rear, display matrix - Liebherr hydraulic oil HVI (-20 to +40 °C) - Tires Firestone Duraforce-Utility 460/70 R24 INCLUDED ACCESSORIES All attachments fit the hydraulic Liebherr quick hitch and were acquired new along with the machine. - Pallet forks detachable - Fixed pallet fork, load capacity 3.6 t, fork length 1,200 mm - Light goods bucket LSB 3.0 m³, width 2,500 mm, undercutting blade, overflow guard, wear strip hardened steel 400 HB (bulk density max. 0.2 t/m³) - Lattice boom extension 3.9 m - Front sweeper FKM 2.4, working width 2,500 mm, mounting plate CAT 2, hydraulic dirt collection container, splash guard, parallelogram mounting system with pivot joint, mechanical adjustment via locking lever, height adjustment via fine-step locking system, polypropylene sweeping roller also suitable for snow removal, 3 heavy-duty swivel rollers, support legs, lashing eyes TRANSPORT DIMENSIONS Length 5,104 mm, width 2,327 mm, height 2,465 mm, operating weight 8,050 kg Fpodpfxez Hx Rce Al Uen SCOPE OF DELIVERY Operating manual digital (MyLiebherr) and printed in German, emergency kit, lifting cylinder support, complete maintenance history Inspection by appointment. Sale from commercial to commercial, price net plus statutory VAT. Transport can be arranged upon request.

Condition: used, Year of construction: 2017, The BIESSE ROVER A 1643 EDGE is a comprehensively equipped CNC machining center with a 5-axis machining head and an integrated edge banding unit. Working area, X-axis: 4,320 mm Swing machining in X: 1,620 mm Working area, Y-axis: approx. 1,580-1,660 mm Travel, Z-axis: 180 mm Edge banding Working area, X-axis: 3,300 mm Working area, Y-axis: 1,540 mm Maximum loading width in Y: 1,900 mm, expandable to up to 2,100 mm 5-axis unit 5-axis machining head C-axis: continuous 360° rotation B-axis: continuous 360° rotation B-axis speed: 18 rpm C-axis speed: 18 rpm Maximum spindle speed: 24,000 rpm Power 11 kW in S1 operation 13 kW in S6 operation Additional features Maximum undercut angle: -10° Collision monitoring for the 5-axis unit Prepared for the use of attachments on the 5-axis unit Work table and clamping system ATS work table 8 support rails 32 adjustable consoles 32 pneumatic vacuum cups Vacuum cups adjustable in 15 steps Pneumatic system divided into 2 working zones along the X-axis Vacuum system Vacuum pump capacity: 250 m³/h Additional equipment 6 lifting bars for easier loading and unloading 28 sensors for detecting lowered stops Stops and positioning 8 rear stops 8 center stops 4 side stops (2 left + 2 right) 2 additional side stops 4 removable center stops (2 left + 2 right) 2 additional center stops Pneumatic positioning and lowering of the stops Drilling unit BH 24L drilling head 13 independent vertical spindles 5 independent horizontal spindles Grooving saw, 120 mm Maximum groove depth: 25 mm Programmable spindle speed up to 6,000 rpm Tool changer 16-position rotary magazine Mounted on the X-axis carriage For tools and attachments Capacities Fodpfx Alozuwyzo Uspn Maximum tool/attachment weight: 7.5 kg Maximum total load of the magazine: 55 kg Edge banding unit GU60A edge banding unit For workpieces up to 60 mm thick Edge banding speed up to 20 m/min Double pressure roller system Glue pot with hot melt system Edge heating lamp, 600 W CNC-controlled edge feeding system Automatic edge trimming Sensor for closed geometric shapes Accessories for edge machining Edge magazine 2-roller edge magazine mounted on the X-axis carriage Maximum roller diameter: 800 mm Maximum edge height: 65 mm Additional units Rounding tool 85 mm, HSK F63 Saw unit HSK F63 for cuts and grooves Maximum saw blade diameter: 215 mm Maximum saw speed: 8,400 rpm Maximum cutting depth with a 215 mm saw blade: 68 mm Post-processing Combined glue joint and edge trimming blade units Tool sets for different edge thicknesses Software bSolid basic module 2D CAD environment Import of DXF, CIX and BPP files 3D machine simulation Tool management Management of 5-axis machining through positioning Assistant-supported program creation

Condition: excellent (used), Year of construction: 2011, operating hours: 80,000 h, functionality: fully functional, clamping force: 1,200 kN, screw diameter: 40 mm, displacement volume: 201 cm³, total length: 5,245 mm, total width: 1,525 mm, total height: 2,300 mm, overall weight: 7,200 kg, input frequency: 50 Hz, input voltage: 400 V, The machine comes from the current series production of a plastics processor and, according to the previous owner, is fully functional. An inspection at the production facility is possible after scheduling an appointment. Key data (according to manufacturer's specifications ENGEL) • Clamping force 1,200 kN (120 t), tie-barless clamping unit • Platen dimensions 790 × 790 mm (Wide Platen), minimum tool size 350 × 350 mm • Tool installation height min. 400 mm, opening stroke 506 mm, max. platen distance 900 mm • Ejector 130 mm stroke, 39.8 kN • Injection unit 1 (330H, horizontal): screw Ø 40 mm, displacement volume 201 cm³, specific injection pressure 1,221 bar / increased 1,667 bar • Injection unit 2 (80W, angled position): displacement volume 38 cm³ (screw Ø 22 mm) or 49 cm³ (Ø 25 mm) [CHECK 09/25: which screw] • Hydraulics: pump drive 30 kW, oil capacity 300 l • Connection 3 × 400 V, 50 Hz, 139 kW / 220 A • Control system ENGEL CC 200 [CHECK 09/25] • Operating hours 87,300 h (as of 09/2026); plasticizing cylinder Ø 40 mm from 2021 with 20,300 h (according to the previous owner) Your advantages • Tie-barless: The tool space is free from tie bars. Large and bulky tools with core pulls can be accommodated, for which a larger clamping force class would often be required in tie-bar machines. • Short setup times: Tools are installed from the side without tie-bar removal. • Automation: Robots travel horizontally into the tool space – smaller cell, lower hall height, shorter cycles. • Tool-friendly: Platen parallelism via the patented ENGEL Flex-Link system (according to the manufacturer). • Hydraulic connections for core pulls, parallel movements programmable (according to the previous owner) – for tools with sliders, undercuts and thread cores. • Combi version with space for a rotary table or indexing plate (according to the manufacturer). • Main injection unit with a newer plasticizing cylinder (2021). • Second injection unit, according to the previous owner, was not used in operation, therefore minimal wear. [CHECK 09/25: unit available + free injection test] Typical applications 2K hard/soft and two-color: handles with TPE zone, housings with molded-in seal, switches and operating elements, connectors with seal, rollers with soft tread, closures with sealing lip, cable glands, medical components, two-color design parts. Single-component: technical precision parts and parts with inserts. Scope of supply • Injection molding machine as described [CHECK 09/25: with both injection units] • ENGEL data sheet, layout plan, platen drawing Not included in the scope of supply: the peripherals visible in the photos (removal/automation with protective enclosure, temperature control units, material handling and drying, mobile switch cabinet) and tools. Terms and conditions • Price on request • Available presumably from week 48/2026 Fpjdpfx Aoz Eimfsl Ujn • Payment 100% advance payment • Transport throughout Europe on request Note: The technical specifications are based on the manufacturer's documentation and the information provided by the previous owner. They are for informational purposes only and do not constitute an agreement on the condition or a warranty within the meaning of §§ 434, 443 BGB. We will confirm individual values during the inspection or upon request. Offer subject to change, prior sale reserved.

Year of construction: 2025, operating hours: 225 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: VAUZ1973LZT031244, Liebherr Telescopic Handler T 33-10, Generation 6 For sale is a Liebherr telescopic handler T 33-10, originally owned, acquired as new from an authorized Liebherr dealer. Used exclusively in biogas and substrate logistics. Maintenance performed according to manufacturer specifications throughout, records available. ENGINE AND DRIVE - Deutz TCD 3.6 L4, 4-cylinder inline engine, water-cooled, turbocharger with intercooler - 105 kW / 143 hp, 3.6 l displacement, 500 Nm at 1,600 rpm - Emission stage EU V / Tier 4f, electronic common rail fuel injection - Hydrostatic closed-loop drive, infinitely variable - Permanent all-wheel drive, 45% limited-slip differential in the front axle - 3 electronically adjustable steering modes, full lock in 3.5 turns - 20 km/h, 41 kN traction force, reversible fan drive LIFTING AND WORKING HYDRAULICS - Max. load capacity 3,300 kg, lifting height 9,747 mm, reach 7,176 mm - Load capacity at max. lifting height 1,500 kg, at max. reach 300 kg - Working hydraulics 106 l/min, single-lever control via multi-function joystick - Lowering brake valves on lifting, tilting, and telescopic cylinders - Auxiliary work circuit on the telescopic head, adjustable flow rate - Hydraulic quick hitch Liebherr Compact and Stereo - Tilting kinematics 126.4°, telescopic cylinder with end-of-stroke damping CABIN - Elastomer mounting, integrated ROPS/FOPS structure internally - Tinted safety glazing front and roof, one-piece windshield wiper - Windshield washer system front and rear, rear window tilting - Driver's door with opening window, lockable when open - 3-stage fan with fresh air intake and filter - Steering column tilt adjustable via foot pedal, driver's seat with artificial leather upholstery SAFETY AND EQUIPMENT - Overload warning device EN 15000 with automatic shut-off, audible/visual - Hill start assist Auto Hill Assist, level adjustment via the front axle - Battery main switch with automatic battery disconnection - Air filter with automatic dust extraction - Central lubrication system, tool-free access to telescopic cylinder lubrication - Work spotlights 2x front, 2x rear, display matrix - Liebherr hydraulic oil HVI (-20 to +40 °C) - Tires Firestone Duraforce-Utility 460/70 R24 INCLUDED ACCESSORIES All attachments fit the hydraulic Liebherr quick hitch and were acquired new along with the machine. - Pallet forks detachable - Fixed pallet fork, load capacity 3.6 t, fork length 1,200 mm - Light goods bucket LSB 3.0 m³, width 2,500 mm, undercutting blade, overflow guard, wear strip hardened steel 400 HB (bulk density max. 0.2 t/m³) Fpedeztakyjpfx Al Ujn - Lattice boom extension 3.9 m - Front sweeper FKM 2.4, working width 2,500 mm, mounting plate CAT 2, hydraulic dirt collection container, splash guard, parallelogram mounting system with pivot joint, mechanical adjustment via locking lever, height adjustment via fine-step locking system, polypropylene sweeping roller also suitable for snow removal, 3 heavy-duty swivel rollers, support legs, lashing eyes TRANSPORT DIMENSIONS Length 5,104 mm, width 2,327 mm, height 2,465 mm, operating weight 8,050 kg SCOPE OF DELIVERY Operating manual digital (MyLiebherr) and printed in German, emergency kit, lifting cylinder support, complete maintenance history Inspection by appointment. Sale from commercial to commercial, price net plus statutory VAT. Transport can be arranged upon request.

Condition: like new (used), functionality: fully functional, spindle diameter: 30 mm, rip fence adjustment: manual, actuation type: electric, rotational speed (max.): 10,000 rpm, rotational speed (min.): 3,000 rpm, overall weight: 800 kg, Equipment: CE marking, SCM T130 Undercut Spindle Moulder | 7.5 kW | Robust and reliable SCM T130 undercut spindle moulder – an industrial-grade machine, ideal for joineries, production facilities, and demanding users. Equipment ready for operation – precision, power, and ease of use in one. TECHNICAL SPECIFICATIONS: Motor power: 7.5 kW Control: from the control panel (comfortable operation) Spindle adjustment: electric Total spindle height: 200 mm Spindle diameter: 30 mm Spindle speed: 3000 / 4500 / 7000 / 10000 rpm Speed change: via belt Dust extraction: 2x 120 mm nozzles Long tables Certificate: CE Why choose this machine? Strong and stable construction – no vibrations, perfect machining quality Electric spindle adjustment – quick and precise setting changes Wide speed range – suitable for various materials and tools Professional machine for intensive use SCM brand – a proven manufacturer in the woodworking industry Machine dimensions: Length: 260 cm Width: 110 cm Height: 120 cm Weight: 800 kg Where can you see our machines? JBS WOODWORKING MACHINERY Wolica Druga 26 23-310 Modliborzyce Lublin Voivodeship It is possible to test the machine on-site. Fpedpsy S Tt Uofx Al Ujn Financing options available through leasing or installments. We arrange transport. jbsmaszyny.pl tel: 664 335 465

Condition: good (used), functionality: fully functional, For sale is a used miter saw/undercut miter saw from the manufacturer Irion & Denz Maschinenbau, Lörrach. The machine is equipped with pneumatic saw blade travel, two-hand operation, and spacious roller tables and is suitable for efficient cutting and mitering of wooden workpieces. Technical data/equipment: Manufacturer: Irion & Denz Maschinenbau Place of manufacture: Lörrach Fodpfxjzymwmj Al Uspn Machine type: Miter saw / Undercut miter saw Max. saw blade diameter: 500 mm Max. cutting height: 100 mm Max. cutting width: 330 mm Saw blade travel, pneumatically controlled, continuously adjustable Cutting activation via two-hand operation Pneumatic workpiece clamping Adjustable workpiece stops Extension tables with free-rolling or powered rollers Spacious roller conveyors for longer workpieces Robust industrial design Additional equipment: Stop with electronic positioning Length measurement input via keyboard or length optimization Electronic positioning/length optimization currently defective The machine is in used condition. Equipment and condition as shown in the photos. Transport is possible for an additional charge! The machine is currently still at the customer's site, but would be available shortly. The machine will be inspected before sale. For used machines with a year of manufacture of 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sale and changes are subject to change. All information without guarantee.

Condition: good (used), Year of construction: 1995, functionality: fully functional, saw blade diameter: 400 mm, max blade diameter 400 mm cutting height adjustment angle adjustment 0″- 45″ spindle diameter 30 mm blade guard max. cutting width with guide bar 1270 mm 2 types of rotation speed 3000 / 4500rpm Fodpfxeqwduxo Al Uspn table top dimensions 1020 x 1120 mm worktop extension worktop extension undercutter max diameter of undercutting saw blade 130 mm diameter of undercutter spindle 20 mm undercutter motor 0,75 kW motor 4 kW overall dimensions L/W/H 2930 x 2600 x 1450 mm weight 711 kg

Condition: good (used), Year of construction: 1996, functionality: fully functional, cutting height (max.): 75 mm, cutting width (max.): 1,200 mm, saw blade diameter: 400 mm, Slitting and cross-cutting saw well maintained in good condition Year of production 1996 GOMAD Poland from the new we are the only owner on the equipment of the unit with the undercutting slab and an additional guide for cutting at an angle, up-and-down blade and tilting at an angle up to 45 degrees Fjdpsu Axf Nefx Al Uepn DTR documentation. Technical data Undercutter on a separate motor 0.75 kw Tilting at an angle 0 45 ' Side carriage Upper shield on the arm Polish manufacturer Gomad Massive stable strong construction Extension and extension tables Cutting width on the right side 120 cm Main saw motor 6 kW, 2880 rpm RPM of undercutting saw 8500 rpm Swing of the saw 0-45° max. bore diameter of main saw f 30 mm max. blade diameter 400mm Undercut saw bore diameter f 22 mm

Condition: like new (used), Year of construction: 2019, functionality: fully functional, SCM TF130ps Undercut Spindle Moulder Spindle diameter: 40mm Fsdpfxjzlw Rns Al Uspn Longitudinal carriage in the worktable Total spindle length: 180mm Main motor power: 7kW Spindle speed change via belt drive: 3000/4500/6000/7000/10000 rpm Spindle rotation: left and right Manual spindle lifting Technical documentation Year of manufacture: 2019

Condition: ready for operation (used), The U2PRW cutting and drilling machine is designed for processing slats and furniture fronts made of solid wood or MDF. The machine works in a semi-automatic cycle. During one cycle the machine performs: cutting at a given angle (in the range of 45 - 90 degrees) and drilling in the jammed plane, or the edge of the element. - Made in Poland TECHNICAL PARAMETERS: max. height of cut material 60 mm max. width of cut material at an angle of 45° 70 mm max. width of the material at an angle of 90° 150 mm max. length of cut material 2200 mm min. length of cut material at 45° 455 mm diameter of main saw 250 or 300 mm undercutter diameter 100 mm max. diameter of bottom milling cutter 35 mm Fsdpfxeq Ii Dls Al Uepn max. depth of bottom milling 15 mm diameter of face drill embedment and bottom milling cutter 10 mm Drill head (face drilling): spindles 4 axial spacing of spindles 32 ; 32 ; 40 mm linear arrangement of spindles max. depth of face drilling 60 mm installed power 7 kW working pressure 0.6 Mpa overall dimensions (length / width / height) 4300 / 1600 / 1570 mm Machining units The machine is equipped with two machining units. The left unit, which is fixed, and the right unit - a sliding unit. Each machining unit consists of the following sub-assemblies - units: a main saw, an undercutting unit, a drilling unit that drills into the jammed plane, and a drilling unit that drills into the bottom of the workpiece. Bottom hole drilling unit The described aggregate is installed as an option. It is used in the processing of corner ties for doorframes with adjustable width. It makes a blind bore , for the can connector. The picture shows the mounted red cover which is at the same time the base for the machined angle strips and the cover with chip extractor. Workpiece pressure The machine tool is also equipped with a clamping system operating in two planes. The clamping area includes horizontal and vertical clamps. The horizontal clamps are responsible for pressing against the vertical bases and straightening the workpiece. Vertical ones, on the other hand, are responsible for immobilizing the workpiece during machining. The horizontal pressure always precedes the vertical pressure. Control The machine's control is clear, easy to use and functional. It allows switching on or off all aggregates separately, additionally with division into left and right sides. All aggregates have independent drive. The right-hand processing unit is set by pressing the control buttons on the control panel. The executive mechanism is a gearbox with an electric motor driving a trapezoidal screw. An electronic control system US with an operator panel and digital display is used to read and set the length of the workpiece. This system is also responsible for automatic corrections to the counter readings when the cutting angles change by 45° and 90°. In addition, it is responsible for automatic basing.

Condition: used, Year of construction: 1991, We offer the following machine: - with roller conveyor --> Outfeed: 4 m --> Infeed: 3 m Technical details: - Saw blade diameter: 450 mm - Cutting diameter: 150 mm - Saw blade arbor: 50 mm - Table size: Ø 700 mm - Table rotatable: 360° - Electric model - Voltage / Frequency: 400 / 50 V/Hz - Compressed air connection: 6-8 bar Fpodpfx Aljzgvqpe Usn - Total power consumption: 3.6 kW - Machine weight approx.: 1170 kg - Machine dimensions: 1.5 x 1.0 x 2.35 m (L x W x H) Circular saw, semi-automatic - Profiling circular saw machine - Undercut saw for cutting materials: steel as solid material, tubes, and profiles, taking into account the cutting range. Cutting speed depends on the material/workpiece to be cut. Miter cut: 30° to 90°

Condition: ready for operation (used), operating hours: 99 h, functionality: fully functional, machine/vehicle number: 620110, year of last overhaul: 2026, HEIDELBERG SM-74-2 | 2-Color Offset Printing Machine Year of manufacture: 1994 Total impressions: 99 million Machine No.: 620 110 Printing specifications: - Cpc 1-04, CP Tronic - Max. sheet size: 530 mm x 740 mm (20.87" x 29.13") - Min. sheet size: 210 mm x 280 mm (8.27" x 11.02") - Max. print format: 510 mm x 740 mm (20.08" x 29.13") - Material thickness: 0.03 mm - 0.60 mm (0.0012" - 0.0236") - Gripper margin: 8 mm - 10 mm (0.32" - 0.39") Print output: - Maximum: 15,000 sheets per hour (sph) Plate cylinder: - Cylinder undercut: 0.15 mm (0.0059") - Distance from lead edge of plate to lead edge of print: 59.50 mm (2.34") Fjdpfxjy Sxb Do Al Uopn Plates: - Size (L x W): 605 mm x 745 mm (23.82" x 29.33") - Thickness: 0.25 mm - 0.30 mm (0.0098" - 0.0118") Feeder: - Electronic pull lay control - Integrated preloading device - Ultrasonic and electromechanical double-sheet detector - Speed-compensated air blast - Self-cleaning pneumatic pull lay Printing Unit: - AutoPlate quick plate change system - Alcolor dampening system - Automatic wash-up devices (inking unit, blanket, impression cylinder) - TransferJacket Blue Delivery: - Non-stop delivery with rake - Super Blue delivery drum - Powder spray device Machine is in production and can be seen in operation.

Condition: repair required (used), Year of construction: 2002, functionality: limited functionality, For sale is a presetting device of the company Mapal and the type Uniset-V The device itself is in good condition and functional, however the digital display is defective and needs to be repaired Measurement of tools, undercuts and distances possible as well as clamping between centers is no problem Technical data: Manufacturer Mapal Type: Uniset-V Year of manufacture: 2002 Digital display Heidenhain Electric axis control 4 axes travel + turntable Additional shelf with sockets for printer etc. No data sheets or operating instructions available Weight approx. 1.5 tons Dimensions: approx. 1.75m*0.75m*2.41m Loading & or shipping possible for an extra charge Fpodpfxjmkikfs Al Usn Prices plus value added tax Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: new, Year of construction: 2026, CORMAK ZX 7055 VARIO Milling and Drilling Machine Main Advantages Rigid cast iron base and column – ensures stability when machining demanding workpieces, reduces vibration, and extends tool life. Variable spindle speed control in two ranges: 75–438 rpm (low range) and 438–2500 rpm (high range) – allows optimal parameter selection according to tool diameter and material type. Fpsdpfxjzd R Eis Al Uon Automatic spindle feed – provides consistent cutting performance and reduces the risk of drill breakage during deep-hole drilling. Tapping function – once the preset thread depth is reached, the spindle automatically switches to reverse rotation. Ground gears – ensure smooth and quiet gearbox operation with stable spindle torque. Dovetail guideways on all axes – provide precise table movement and reliable machine geometry. Swiveling head ±90° with height adjustment – facilitates chamfering, undercutting, and angular machining operations. Forward and reverse spindle rotation – enables safe tapping and tool withdrawal. Efficient cooling system – effectively dissipates heat during machining, prevents overheating of both the tool and workpiece, and improves machining accuracy and tool life. Standard Equipment Variable spindle speed control Electrically powered spindle head height adjustment Coolant system Technical Description Heavy-Duty Cast Iron Construction The robust cast iron construction forms the foundation of the machine’s durability and precision. The ZX 7055V DRO milling and drilling machine maintains excellent stability even during the most demanding operations. The machine features continuously variable spindle speed adjustment in two ranges: Low range: 75–438 rpm High range: 438–2500 rpm Large Cross Table with Precision-Ground Surface Attention to detail is a key design feature. The large cross table with a precision-ground surface ensures excellent flatness, resulting in highly accurate machining. Dovetail Guideways Innovative dovetail guideways provide smooth and precise movement along all three axes, enabling outstanding machining results without compromise. Forward and Reverse Rotation Adapt the machine to your requirements. The ability to rotate the spindle in both directions provides additional flexibility during machining operations. Swiveling Head ±90° and Adjustable Head Height Handle a wide variety of machining tasks thanks to the ±90° swiveling head and adjustable head height. Achieve precise results under all working conditions. Optional Machine Base A machine stand/base is available as an optional accessory. Technical Specifications Parameter Value Maximum Drilling Capacity Cast Iron (HT200) 45 mm Steel 32 mm Maximum Face Milling Capacity 80 mm Maximum End Milling Capacity 28 mm Table Size 820 × 240 mm Table Travel (X/Y) 595 / 185 mm Maximum Tapping Capacity M24 Spindle Taper MT4 Spindle Speed Range Low Range 75–438 rpm High Range 438–2500 rpm Spindle Travel Manual 107 mm Automatic 100 mm Distance from Spindle to Column Surface 250 mm Maximum Distance from Spindle Nose to Table Surface 445 mm Motor Power S1/S6 1.5 / 1.8 kW Net Weight 350 kg Overall Dimensions (L × W × H) 1084 × 924 × 1550 mm Height with Base 2150 mm

Condition: new, Year of construction: 2026, The CORMAK ZX 7055 VARIO DRO milling and drilling machine is a high-performance universal machine designed for drilling, milling, and tapping operations in steel and cast iron. Its robust cast-iron construction, continuously variable spindle speed control in two ranges, and digital position readout system ensure high accuracy and repeatability in single-piece and small-batch production. Main Advantages of the Machine Rigid cast-iron base and column – provide excellent stability during machining of demanding workpieces, reduce vibrations, and extend tool life. Continuously variable spindle speed control in two ranges: Low range: 75–438 rpm High range: 438–2500 rpm Allows optimal selection of cutting parameters depending on tool diameter and material. 2-axis digital readout system (DRO) – enables fast and accurate positioning while reducing setup time and eliminating reading errors from manual scales. Automatic spindle feed – ensures smooth cutting performance and reduces the risk of drill breakage during deep drilling operations. Thread cutting function – after reaching the preset tapping depth, the spindle automatically reverses direction. Ground gears – provide quiet transmission operation and stable spindle torque. Dovetail slideways on machine axes – ensure precise table movement and accurate geometry. Rotating head ±90° with height adjustment – allows easy execution of angled machining operations, chamfers, and undercuts. Left/right spindle rotation – enables safe tapping and tool withdrawal. Efficient cooling system – effectively removes heat from the cutting zone, prevents overheating of tools and material, improves machining accuracy, and extends cutting tool life. The core of the machine is a heavy cast-iron structure with wide guideways, minimizing deflection during face and end milling operations. The large cross table provides a spacious working area and features a precisely ground surface to ensure accurate workpiece positioning. The spindle with an MK4 taper is driven by an S1/S6 1.5/1.8 kW motor with variable speed control. The integrated cooling system stabilizes the cutting temperature and improves the quality of machined surfaces. The combination of a 2-axis DRO system, ground gears, and rigid guideways provides excellent dimensional repeatability and high surface finish quality. The automatic spindle feed and two-speed spindle range allow optimal machining parameters for: drilling in steel up to Ø32 mm, drilling in cast iron up to Ø45 mm, face milling up to Ø80 mm, end milling up to Ø28 mm. Standard Equipment Variable spindle speed control 2-axis digital readout system (DRO) Ø80 mm milling cutter head with inserts Drill chuck Cooling system Technical Specifications Parameter Value Maximum drilling capacity – cast iron (HT200) 45 mm Maximum drilling capacity – steel 32 mm Maximum face milling diameter 80 mm Maximum end milling diameter 28 mm Working table dimensions 820 × 240 mm Table travel (X/Y) 595 / 185 mm Maximum tapping capacity M24 Spindle taper MK4 Motor power (S1/S6) 1.5 / 1.8 kW Low spindle speed range 75–438 rpm High spindle speed range 438–2500 rpm Spindle travel – manual 107 mm Spindle travel – automatic 100 mm Distance spindle axis to column surface 250 mm Fsdpfxeyapyrs Al Uepn Maximum distance spindle nose to work table 445 mm Net weight 350 kg Overall dimensions 1084 × 924 × 1550 mm Height with base 2150 mm

Condition: new, Year of construction: 2026, machine/vehicle number: SÇ 401 Aluminyum Pvc Alttan Çıkma Kesim Makinası, functionality: fully functional, • Complies with CE standards. • Performs precise cutting at 0 - 180 degrees and intermediate angles. • Quick setting stops for 15, 22.5, 30, 45, 60, and 90 degree angles. • Table locking lever for intermediate angles. • Saw output speed regulator reduces speed when cutting aluminium, decreasing motor load. • Safety guard for secure cutting. • Diamond saw blade diameter: 450 mm, output distance: 12.5 cm. • Standard with measurement and transport conveyor (2.5 metres right and left). Fodpsq U Tctjfx Al Ujpn OPTIONAL • Cooling system and Hydro check system available for aluminium cutting. • Capability to work with a digital meter.

Condition: used, Year of construction: 2026, functionality: fully functional, Sharpening device for drill bits made of HSS or any other hard metals, ensuring precise grinding and easy handling. Adjustable tip angle in the 90°–135° range. This model is equipped with an additional slot for sharpening undercuts. Machine features Precise grinding and convenient handling. Sharpening drill bits with ease. Portability due to its modest dimensions. Dressing wheel promising superb efficiency. Fully equipped; with a handle inside the device. Additional slot for sharpening undercuts. Technical data Drill bits diameters capability ø2–13 mm Angle of the tip 90°–135° POWER 120 W / 230V Motor speed 4800 rpm Approx. weight 9 kg Dimensions 330 x 170 x 160 mm Fjdpfozp Ea Esx Al Ujpn PLEASE NOTE!!! This machine is a returned item; it is second-hand but in working order. NO WARRANTY AND NO RETURNS!!

Condition: used, functionality: fully functional, SCM T130 Undercut Spindle Moulder Spindle diameter: 35mm Total spindle length: 160mm Main motor power: 5.5kW Spindle speed, belt-driven, adjustable: 3000/4500/6000/7000/10000 rpm Spindle rotation: both left and right Electric spindle lifting mechanism Fpedpfx Aljzakgms Uon

Condition: ready for operation (used), Year of construction: 1995, functionality: fully functional, bar diameter (max.): 32 mm, turning length: 80 mm, rotational speed (min.): 3,150 rpm, drilling depth: 80 mm, No minimum price – guaranteed sale to the highest bidder! The machine is sold complete with collets, holders, and additional accessories! Fpedpfxoz Ag A Ij Al Ujn For more Schütte multi-spindle machines from the same location, see below! TECHNICAL DETAILS Maximum turning length: 80 mm Maximum drilling depth: 80 mm Largest material passage: 32 mm Maximum bar feed: 125 mm Spindle speed (turning): 200–3,150 rpm Spindle speed (right-hand threading): 11.2–1,575 rpm Thread cutting unit: Right-hand thread via undercut MACHINE DETAILS Coolant capacity: 600 l Pump output: 170 l/min Dimensions & Weight Footprint: 7.3 x 2.5 m Height: 2 m Weight: 8,300 kg Voltage: 380 V Frequency: 50 Hz Main drive: 20.5 kW Immersion pump: 1.5 kW Feed drive: 1.5 kW Hydraulic pump: 1.5 kW Circulating oil pump: 0.25 kW EQUIPMENT 6 cross slides 6 longitudinal slides 6 cams for cross slides 6 cams for longitudinal slides Operating tools Collets Holders Additional accessories