Used Waste-Press for sale (15,496)

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Isdpfxszuzw De Anveba Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Manufacturer: OTT Type: 300-K-D0 Year of manufacture: 1996 Technical data Ibodpfjzuzwwsx Anvoa Plate dimensions: 2550 x 1350 mm Hot water heating 6 pressure cylinders Total pressing force: 135 t Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2007, Lamination press Manufacturer: Dimter Type: PROFIPRESS L2500 Year of manufacture: 2007 Technical data Wood dimensions to be processed Wood width, panels: 30 - 150 mm Wood thickness: 11 - 60 mm Wood inlet length: 800 - 2500 mm Panel widths, variable: max. 1300 mm Specific pressing pressure for cross-sections of 2500 x 60 mm: up to 1.6 N/mm2 The pressing surface per press cycle must not be smaller than 100 cm2 Filling width of the press per cycle: min. 650 mm / max. 1300 mm Max. filling area of the press per cycle: 3.25 m2 (The max. usable press width depends on the widths of the individual lamellas.) Wood type Softwood/hardwood Press without options Electrical connection, press: 7 kW Iedpfx Aszuzwqsnvjba Electrical connection, 40 kW generator: 56 kW Operating voltage: approx. 400 Volt / 50 Hz (C/s) Collection table extended to 3700 x 1300 mm, with stainless steel wood support Motor-driven multi-function slider Lamination press Profipress L 2500 Press bed area approx. 2500 x 1300 mm Sturdy base frame with lower press table made of stainless steel as a grounding electrode Quick-change stop guide sets for panel thicknesses of 19 - 40 mm, which can be hydraulically adjusted to the current filling width Hydraulic special pressure elements ensure uniform pressure distribution over the entire joint length and compensate for tolerances In multi-lane operation, filling widths may vary by a maximum of 15 mm Upper pressure plate with hydraulic drive generates high vertical pressing pressure for minimal displacement Integrated hydraulic unit for generating pressing force and driving the hydraulic motors Control cabinet and control panel Protective cladding Additional individual pressure elements from above Automatic gluing station with precision gluing head Infeed for different widths Camera Washing and rinsing device for gluing head Modem incl. software for online connection Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm - Min. filling height 900 mm - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm Isdpfx Aszuzwkenvsba - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm - Max. power 13.2 kW - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Continuous body press Ijdjzuzv Tspfx Anveba Manufacturer: LIGMATECH TYPE: MPP 15 Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Working height: 500 mm Transport speed: min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2000, Corrugated board press Manufacturer: Hüttenhölscher Year of manufacture: 2000 Technical data Voltage: 400 V Current: 32 A Isdpfozuzvmjx Anvsba Frequency: 50 Hz Compressed air: 6 bar Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, Short-cycle pressing line Manufacturer: Wemhöner Type: KT-F-1E Year of manufacture: 2001 Technical data - Pressing area: 5,750 mm x 2,200 mm - Operating side: left - Plate dimensions: Ijdpfxszuzi To Anveba Length: 2 x 2,600 mm - 2 x 2,620 mm Width: 2,070 mm Thickness: 6 mm - 40 mm - Pressing pressure: approx. 40 kg/cm² Note: Upon request, the complete layout plan of the system can be sent. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 1998, - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Door pressing system Manufacturer: Wild Year of manufacture: 1998 For door dimensions: - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Consisting of the following sections: 1. Continuous door panel gluing with frame assembly station / 2. Pressing line with hardboard facing station Section 1 consists of: Iedpjzuzgrjfx Anveba - Gantry loading system - Angle transfer with longitudinal and cross saws - Loading and feeding of the longitudinal and transverse frame parts from magazines - Longitudinal cutting station for the longitudinal frame parts - Connecting station of the frame parts with the door panel core. With clamping devices - Conveyor belt angle transfer with shuttle transfer of the door panel cores onto the glued hardboard Section 2 consists of: - Loading of the hardboard - Brush cleaning machine - Hardener application machine from below - Glue application machine from below - Roller conveyor - Angle transfer for the lower hardboard - Vacuum reversing device for the upper hardboard - Automatic facing station for hardboard and door panel cores - 2 door presses, each with 2 x 4 pressing stations, arranged parallel to each other - Both presses are loaded at the infeed with 1 shuttle loading basket - Both presses are unloaded at the outfeed with 1 shuttle unloading basket - Angle transfer to the infeed into a hedgehog buffer - Angle transfer at the outfeed of the hedgehog buffer and feeding to the stacking station - One-sided vacuum stacking with protective plate space Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: excellent (used), Year of construction: 2004, operating hours: 76 h, machine/vehicle number: HF112305, Size 47 x 66 cm, Console DTC (Sakurai Delivery Top Console) with Touch Screen, Full Remote Control Operation, SIS (Sakurai InterActive System) for make-ready, Plate Running Register system, SAS (Sakurai Auto Set) for paper size and thickness, SPC (Semi-automatic Plate Change), Cocking Register, Automatic Washers: Blanket Cylinders & Inking Rollers, Olivermatic Dampening, Baldwin Refrigeration System & Bal Control, Feeder with Suction-belt feed table, Electronic Double Sheet & Side Lay Detector, Chromed Impression Cylinders, Perfector 4/0 - 2/2 (Fully automatic), Semi-High Pile delivery, Powder Spray. Iedpfozubgrox Anvsba

Year of construction: 1999, condition: used, Colour: Grey Membrane press Orma PM/AIR Year of construction 1999 Serial number 52850199 Dimensions 2300*900mm Max panel size 2200x800mm Max panel thickness 40mm 8 cylinders diameter 100mm Stroke 150mm Pressure 160T Pressure pressure 6 kg/cm² Heating 13kW Total power 17.3kW 380V, 35Amp Dimensions: 3900x1800xH2100mm, weight 5900kg - Year: 1999 - Documentation available: No - CE certificate present: No - Serial number: 52850199 - Main motor power [kW]: 17.3 - Max. workpiece length [mm]: 2200 - Max. workpiece width [mm]: 800 - Max. workpiece height [mm]: 40 - Number of cylinders [pcs.]: 8 Ibjdpfxjwnhice Anvea - Cylinder diameter [mm]: 100 - Total working pressure [Ton]: 160 - Working pressure [kg/cm²]: 6 - Heating boiler present: Yes Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, total length: 11,500 mm, total width: 2,450 mm, total height: 2,600 mm, Colour: Green Empty weight: 16.500 kg Veneer press Feed-through press HOT Colombo Machine dimensions: 4400x1400 Oil heated input/output is included 8 cylinders Complete with glue roller etc. - Documentation available: No - CE certificate present: No - Press drive: Hydraulic - Max. workpiece length [mm]: 4500 - Max. workpiece width [mm]: 1400 - Max. workpiece height [mm]: 140 - Total stroke [mm]: 140 Ibsdpfx Aewnhvvonvoa - Number of stages [pcs]: 1 - Material of press plates: Steel - Number of cylinders [pcs]: 8 - Cylinder diameter [mm]: 85 - Working pressure [kg/cm²]: 4 - Heating type: Oil heated - Voltage [V]: 400 - Transport dimensions: 11500mm x 2450mm x 2600mm (l x w x h) - Transport weight [kg]: 16500kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: good (used), Year of construction: 2018, operating hours: 40,350 h, Baling press Presona LP 85 VH2, year of manufacture 2018 Technical data: Manufacturer Presona Sweden Type LP 85 VH2 Year of manufacture 2018 Drive power 2 x 45 kW Operating hours 40,350 Effective operating hours approx. 22,000 Pre-compression force 28 t Main compression force 85 t Feed opening 1500 x 1100 mm Bale dimensions 750 x 1100 mm Bale weight 450 - 650 kg Theoretical volumetric capacity: 1200 m³/h Throughput capacity at 30-100 kg/m³: 13-30 t/h Tying 5-strand vertical, (3-strand horizontal) Oil tank volume 2000 L Transport dimensions of press 10400 x 2400 x 2800 mm (LxWxH) Weight approx. 27000 kg Materials: Paper, cardboard, PET bottles, films, light waste. Ibsdpfozulknex Anvea Note: The press is in good condition. It has been dismantled from ongoing operation. The following work has been carried out by us: New wear plates (Hardox) in the press channel Seals completely replaced on the main cylinder Oil filter changed Vertical tying mechanism overhauled and made functional The horizontal tying mechanism is currently not functional. The technical documentation is available. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any possible errors. The offer is subject to change, prior sale is reserved, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment ex works, without warranty.

Condition: used, pressure 160 t passage width / mm stroke / mm Working height 800 mm total power requirement 15 kW weight of the machine ca. 11,8 t - Table size: 1000x1000mm - Distance table/ram, large stroke above, gain. above: 800mm extra information Removable table Iodoiulkqopfx Anveba

Condition: used, 1x bending knife from a VOEST press brake Length: 4050 mm Weight: approx. 120 kg Iodey Tbvmspfx Anveba For further dimensions see pictures.

Condition: new, Year of construction: 2025, sheet thickness - max. 8 mm pressure 200 t chamfer lenght 3200 mm engine output 15 kW return speed 105 mm/min working feed 9 mm/sec x-travel 600 mm Max. opening height 570 mm control DELEM DA53T GERD WOLFF KANTO 200T CNC Electro-Hydraulic Press Brake CNC axis accuracy 1) Machine sliders (Y1, Y2) – synchronisation precision: The slider movement axes control the bending depth and bending angle. The system consists of the control unit, two glass scales (Y1, Y2) installed on the work table, electro-hydraulic proportional valves and an amplifier. A closed control loop detects and controls the relative position of the slide and table as well as the speed and position of the slide. This ensures the synchronisation of the slide and maintains the bending depth and angle with high precision. Positioning accuracy: ±0.02 mm Ibsdpfx Ajxf Na Uonvoa Repeatability: ±0.02 mm 2) Machine backgauge (X axis): The forward/backward movement of the X-axis controls the dimensions of the sheet metal cut. The stop bar is driven by a servo motor and moves the crossbeam via a ball screw and linear guide. Operation is stable and precise. Positioning accuracy: ±0.10 mm Repeatability: ±0.03 mm 3) Mechanical compensation system (V axis): The pull plate of the mechanical compensation is moved by a motor so that the compensation points are formed in an arc shape. The points perfectly compensate for the elastic deformation of the work table and slide to ensure angular constancy and straightness of the workpiece. Position sensors and CNC control ensure precise regulation.

Condition: used, 1x bending knife from a VOEST press brake Ijdjzcgh Eopfx Anveba Length: 4050 mm Weight: approx. 115 kg For further dimensions see pictures

Condition: used, Year of construction: 1979, pressure 100 t Ibjdpfx Aney Tpr Aevsa stroke 500 mm table surface area 4000x500 mm weight of the machine ca. 5,7 t HY – S 100 RH MAE hydraulic straightening press, complete with straightening unit Year of manufacture: 1979 Approved in accordance with UVV Stroke: 500 mm Pressure capacity: 100 tonnes Table: 4000 x 500 mm Weight: 5700 kg

Condition: used, Year of construction: 1991, pressure / t plate thickness / mm Iodpjwgi S Njfx Anveba no. of strokes / Hub/min Condition: used The punching machine works perfectly. A functional video is available.

Condition: used, pressure 1000 t table length 2110 mm table width 1755 mm stroke 500 mm 18 min work height max. 380 mm 4 Punkt weight of the machine ca. 107,25 t dimensions of the machine ca. / m WILKINS & MITCHELL Trimming press with accessories Pressure force: 1000 t With discharge table and gear component Table area 2110 x 1755 mm Weights Stand: 47.1 T Table: 8.84 T Fumrungen: 1.72 T Drive: 26.47 T Compensating cylinder: 1.65 T Motor mount and guard: 2.04 T Pusher: 11.53 T Adjusting screws and bolts: 2.66 T Slide setting: 0.85 T Miscellaneous: 1.02 T Hydraulic ejector: 0.52 T Total weight: 107.25 tons Iodpfx Ajgrnaqenvjba

Condition: used, Dimensions: approximately 2500 x 1200 x 600 mm, semi-hydraulic, with electro-motorized adjustment of the press wall. Ibedpfx Ajzd Hm Nenvea Storage location: Nattheim.

Condition: new, The Press block feeder is a reliable machine suitable for unloading composite pallet blocks for the production of pallet legs. The PBF can simultaneously unload from two pallets of composite pallet blocks to one or two conveyors. Like the other gantry robots, the PBF is user-friendly and has the same type of interface as the rest of Mychrome’s equipment. The grip sheet is automatically removed and placed in a waste container. Machine specification: Standard performance Operators: 0 Length: 5 m Width: 2,5 m Height: 3 m Power: 10 kW, 3x400 V+N Ibodpfxowduuwo Anvoa Pneumatic system: 7 bar compressed dried air: 100 L/min Should be filled and controlled: Container for lubricating oil Machine capacity: 36 blocks per minute (one type of blocks) Standard equipment: - 1 gantry robot with operator panel - 1 vacuum gripper

Condition: used, Buchformpresse / Book Forming Press Kolbus FE Iedpfx Anjzu Dnlsveba Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Clamping unit heating capacity, 1 heating rod / 8 heating rod: 0,48 / 0,9 kW clamping force: 2 x 500 kN heating plate dimensions: 550 x 600 mm piston stroke: 250 mm diameter of piston, main cylinder: 240 mm diameter of piston, locking cylinder. 39 mm locking cylinder: 260 mm Return capacity: 2 x 600 kN Ibodpfxozum Uzj Anvoa dimensions: 2600 x 2100 x 2100 mm weight approx.: 5 t

Condition: excellent (used), Year of construction: 2006, Dimension: 2650 x 2100 x 2100 mm Clamping Force: 635 KN Working pressure: 206 bar Piston diameter: Ø200 mm Stroke: 140 mm Daylight: 150/180 mm Heating plant dimension: 250 x 300 mm Max. mass of heating plant: 70 kg Oil reservoir: 100 l Isdpfszum Unox Anvjba Rated power: 19.66 kW Heater capacity: 9.6 kW Vacuum motor power: 2,6 kW Between light curtain and mould area: 270 mm Stroke of vacuum cover: 140 mm The vulcanizing press from manufacturer PAN STONE, model S-V-65-2RT-PCD, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. The machine was part of a production line responsible for manufacturing high-performance seals used in various industries. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.

Condition: good (used), Year of construction: 2005, functionality: fully functional, Clamping force: 4900 kN Working pressure: 206 bar Heating plate dimensions: 700 x 700 mm diameter of piston: 558,8 mm max. stroke: 250 mm daylight: 300 mm max. mass of heating plant: 560 kg capacity of oil tank: 1100 l rated capacity: 82 kW heating capacity: 56 kW enginge output, vacuum motor: 4 kW Stroke of vacuum cover: 200 mm dimensions: 3975 x 2935 x 2555 mmm Equipped with a crane runway (monorail) with three chain hoists Ibedpfjzum Tqjx Anvsa Producer: STHAL Year: 2011 Lifting capacity: 3 x 400 kg Lenght of crane runway: ca. 3500 mm Rolling chassis Lifting capacity: 400 kg Lifting height: 3000 mm stroke speed - main stroke: 4 m/min stroke speed - fine stroke: 1 m/min The vulcanizing press from manufacturer PAN STONE, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.