Used Wedge for sale (476)

Condition: new, machine/vehicle number: 5c7120ea17bcf92d3b69899da, empty load weight: 14 kg, maximum load weight: 35 kg, overall weight: 50 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with exchangeable 2 king pins 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2x wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit with spray flaps behind each axle 1x storage box Box, w=2 350 mm x l=730 mm x h=640 mm, bolted transversely at the front to the floor of the gooseneck, with 2 storage trays Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Excavator trough above the rear axles starting to the rear, approx. 500 mm wide and approx. 230 mm deep Low loader lashing eyes 3 pairs of lashing eyes per 10 tons at the front gooseneck, 8 pairs of lashing eyes per 10 tons in the low bed, 3 pairs of lashing strips in the tramline area of the low bed, 3 pairs of lashing eyes per 10 tons in the axle/rear area Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Hydraulic forced steering via saddle deflection wedge acting on all 3 axles, Post-steering with radio remote control + auto toe-in, (up to max. 20 km/h)Note! A 2-pin Nato socket with at least 2 x 35 mm² is required in the truck for the power supply to the steering system. Power is supplied to the pump unit via a Nato connection cable to the towing vehicle, without truck installation (re-steering must be used once a week). Air suspension Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Kdedpfxji Ri Hgj Ab Uow 2 swap-proof coupling heads at the front, without connecting cable With lifting & lowering valve, hold function in lowering position + auto-reset function Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle driving stability system Trailer Infocenter, for displaying vehicle data such as axle loads (no calibrated scales), mileage and diagnostic/system messages. Electrics 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white LED position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1x additional LED work light(s) at the rear, switched via reversing light 1x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck with steel / checker plate covering In the tramline area with 70 mm softwood floor, in the wheel housing area with steel / checker plate covering, low bed can be raised hydraulically on the left and right in the tramline area for entry, via truck auxiliary drive Rear slope with 70 mm softwood floor Drop deck length approx. 6,300 mm Drop sides 25 mm aluminum h

Condition: excellent (used), functionality: fully functional, power: 25.01 kW (34.00 HP), fuel type: diesel, color: black, fuel: diesel, gearing type: hydrostat, Year of construction: 2018, operating hours: 714 h, Equipment: air conditioning, all wheel drive, hydraulics, KÄRCHER MIC 34C Municipal tool carrier with winter service equipment consisting of: - KUGELMANN silo spreader with 320l volume and control panel - KUGELMANN Wedge-Vario snow plow with 140cm max. clearing width This KÄRCHER MIC 34C was built in 2018, has only 714 total operating hours and 261 hydraulic hours according to the counter and is in a well-kept overall condition with normal signs of use and wear, fresh from the major customer service, ready for immediate use, cf. NP € 80,000! - Net price 31.900,-€ // Gross price 37.9611,-€ ) - Viewing / test drive possible - Shipping can be organized nationwide, the costs depend on the distance! - Our leasing partner will be happy to provide you with an attractive leasing / financing offer! Kdedpfsu Th E Rox Ab Uow

Condition: used, 8 Multi wedge profile plug gauges in wooden boxes Kedpfectiwisx Ab Usdw L 4734-44

Condition: new, MVD SERIES B - 3,100x135Tn SERIES B - 4 Axes Large press brake for achieving outstanding bends and flawless workpieces The body and upper beam are of steel construction, designed according to minimum and optimum strength criteria. Model: B135/3100 Bending force: 135 tons Bending length: 3100 mm Distance between uprights: 2600 mm Ram stroke: 260 mm Daylight: 465 mm Throat depth: 410 mm Table height: 940 mm Length x Width x Height: 4690 x 2340 x 2980 mm Approach speed: 210 mm/s Return speed: 130 mm/s Bending speed: 10 mm/s Oil tank capacity: 180L Main motor: 11 kW Weight: 7,750 kg Standard features: CNC 3 axes Y1, Y2, X 260 mm stroke, 410 mm throat depth ESA S630 CNC control unit ± 0.03 mm precision SERVO-driven, motorized rear gauge X = 750 mm Promecam quick-release punch holder Sliding front sheet support arms Special narrow bottom table by MVD (European type) GIVI optical linear scales Standard punch tooling (H: 67, 850 R:08) Standard die tooling (60x60 mm, 4 Vee V=16-22-35-50 mm, 85°, H:60) Kodpfx Aoxfzpzeb Uodw LED lighting in RAM Optional features: Choice of X-axis backgauge options with 2-4-6-8 stops Wide bottom table for Multi Vee forming dies Anti-deflection crowning with original Wila wedges AKAS or DSP front laser safety systems Additional backgauge fingers Front laser safety

Condition: new, Motor ----- 750W - 230V - 1Phase Drilling capacity ----- 20 mm Pin stroke ----- 82 mm Spindle mounting ----- MK2 Variable speed Spindle speed 400 ~ 2000 rpm Work table ----- 305 x 305 mm Foot ----- 460 x 280 mm Column diameter ----- 72 mm Overall height ----- 1590 mm Weight ----- 74 kg Packaging ----- 1150 x 500 x 300 mm INCLUDED Kodsga T Hcopfx Ab Uedw * Digital depth stop * Digital spindle display * CE cover * Laser device * LED illumination * CE emergency stop * Drill head with MK2 adaption * Driven wedge

Condition: excellent (used), Original spacer rings 145 Ø x 86 Ø with 1 groove 16.5 mm in various widths, 1 used saw shaft 60 mm Ø with 2 wedges 16 mm wide including 1 sliding bush 120 mm effective clamping length with left-hand threaded clamping nut suitable for right-hand machine and bearing bush for front flap Kodpfxowaiaao Ab Usdw

Condition: new, machine/vehicle number: 7272fc3b6a97f9be58a222f05, empty load weight: 5 kg, maximum load weight: 32 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Fine-grained steel welded construction, fifth wheel plate with interchangeable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with incl. guide wedges on both sides Incl. guide wedges, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 30 foot or 1 x 40 foot container. Adjustment via central telescope as an interlocking central tubular frame with bolt lock. Optimum fifth wheel load when transporting 30 foot and 40 foot containers. 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Hydraulics 100 Low-pressure cylinder max. 150 bar, with HDK screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Incl. Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 170 2-line compressed air brake system Colored line routing for easy service. Kdsdpfxoi Riv Eo Ab Ujw Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck instal. calibrated scales) Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light

Condition: good (used), Key bar chuck, power chuck, three-jaw chuck, three-jaw lathe chuck Kdedpfsxdkmyox Ab Uew -Manufacturer: Forkardt, wedge bar chuck type F 400 -Chuck size: Ø 400 mm -Bolt circle: Ø 235 mm -Adapter: Short taper 11 / cone 192 - 196 mm -Through hole: 111 mm -Dimensions: Ø 400 x 325 mm -Total weight: 138 kg

Year of construction: 1982, condition: ready for operation (used), We offer you frame saws: 1. Bogli 71 Frame Saw with Infeed and Auxiliary Trolley and Distribution Device after the Sawmill Sawmill Type: Bogli Marathon 71 - Frame: 710 mm, hydraulic sawmill - Hydraulic adjustment of saws, raising and lowering of roller - 55 kW motor - Carriage with auxiliary trolley, track gauge 90 cm - Distribution unit after the sawmill Everything as shown in pictures no. 1, 2, 3, 4 Price negotiable 2. Linck E 28-28 Frame Saw - Frame stroke: 600 mm Everything as shown in pictures no. 5, 6, 7, 8 Price negotiable Kodpfjn I Udxsx Ab Ujdw 3. Linck Frame Saw with Loading Trolley and Distribution Device after the Sawmill Trak Linck 71 - Frame width: 710 mm - Feed: 12 m/min - Fully hydraulic: hydraulic adjustment of saws, lowering and raising of the roller - Linck hydraulic loading trolley with additional device - Distribution device after the sawmill (bag, wedge) Everything as shown in pictures no. 9, 10, 11, 12, 13 Price negotiable

Condition: used, functionality: unexamined, Year of construction: 1999, machine/vehicle number: 201805015, pressing force: 220 t, working length: 3,050 mm, Used press brake. 220 ton 3 meters 6 axes Technical specifications Voltage: 400 V Type: PPEB 220/30 Force: 2200 kN Working length: 3050 mm Distance between uprights: 2600 mm Stroke: 250 mm Table/ram opening: 485 mm Throat depth: 400 mm Approach speed: 100 mm/s Working speed: 9.6 mm/s Kdedpfxowzw Sme Ab Usw Return speed: 113 mm/s Motor power: 22 kW Oil capacity: 350 l Machine weight: 14,500 kg Control: CADMAN CNC Table width: 150 mm Noise level: 80 dBA Pump flow: 48 l/min Pump model: Voith IPV 4-32 High precision and high flexibility. The PPEB press brake is a robust, highly technological machine. PPEB gives you the freedom to configure a press brake to suit your production requirements. Automatic crowning The crowning system counteracts machine deflection to ensure precise and repeatable bending. Our wedge system is custom-built for each machine and provides crowning along the entire table length. Robust structure A single-piece welded frame guarantees the machine’s precision.

Year of construction: 2023, operating hours: 6,000 h, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 2206006-01, VIBRATING FLIP-FLOP SCREEN MODEL “ZXX 2400/7200” TECHNICAL DATA Procuct charateristics:  Production: PURPLE  Gran size: 0 - 80 mm  Density: 0.4 – 0.5Tn/m3  Temperature: Ambient  Humidity: 55% Production characteristics:  Capacity: 50 Tn/h  Screening size: 10 – 15 mm  Machine production: Continuous  Material behavior: Known  Machine Characteristics Working length: 7200 mm Working width: 2400 mm o Working surface: 17.30 m² Frame: Carbon steel Execution: Supported o Slope: 20º Number of decks: 1 o Screen surface: Elastic polyurethane panels o Screening opening: 1-15 mm o Maths side closure: Polyiurethane wedges o Cover: Included, rubber o Vibrating weight: 7.500 kg  Vibrator characteristics: o Typeofvibrator: 2 Mechanical Vibrators o Centrifugal force: 42.500 kg o Frecuency: 860 r.p.m. Engine: Supply: Triphase 400 V, 50 Hz Power 24 Kw Speed: 860 r.p.m.  Vibration characteristics: Kdsdjv Hlnhepfx Ab Usw o Stroke 8 mm o Frecuency: 950 r.p.m. o Aceleration: 4.6 G o Stroke subresonant frame: 8 mm + 8 mm = 16 mm Suspension system: o Tipodeantivibrantes: 8AMCsuspensions model AB-HD-50-2 o Isolation: 90% o Dynamic load: 4200 daN o Frecuency: 20 Hz  Paint finishing: o Cleaning and degreasing of surfaces. o Primary coat: glycerophtalic, 70 µ. o Finishing coat: glycerophtalic, 40 µ. o Color RAL to be defined

Condition: used, Year of construction: 1978, Technical details: table surface area: 1970 x 400 mm distance between table/spindle: min./max. 150 / 250 mm rapid traverse: 1 / 2 m/min revolution per minute: Frässpindel: 112 ... 1400 / 12 step U/min milling spindle taper: DIN 2019 = Nr. 40 (SK40) axial adjustment: manuell = 150 mm quill feed: 0,012 / 0,025 / 0,05 mm/U feed range - horizontal: Frässchlitten: 8...100 / 12 step mm/min Kdsdpsu Ndhiefx Ab Uow total power requirement: ca. 8,4 (10,5 kVA) kW machine weight approx.: 3000 kg dimension machine xH: 3,05 x 2,7 x 2,0 m wedge-groove milling machine Application: Milling of straight and helical grooves. Multiple groove milling with automatic program sequence. Further features: - distance spindle axis / lower edge counterholder: 55 mm - axial movement of the counter bearing sleeve 50 mm - milling carriage movement horizontal 1000 mm (automatic + manual by hand) and vertical 100 mm by hand + max. 5mm automatic/hydraulic Equipment: - chip container 470x300x300mm - 2x oil collecting basins (3200x1500x70 and 3200x800x60mm) - some accessories/tools *

Condition: new, machine/vehicle number: a203d9a559ff6484cf2a14c1f, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, fifth-wheel plate with replaceable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with guide wedges on both sides, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 20 foot or 1 x 30 foot container. (Note! low fifth wheel load for 20 foot containers) Adjustment via central telescope as an interlocking central tubular frame with pin lock. 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Free support foot corner dimension or free swing radius to the rear approx. 1850 mm 2 wheel chocks with holder Half-shell mudguard with anti-spray flaps according to EG Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Kdjdpfei Ri Avex Ab Ujw Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/65 R22.5 Manufacturer's choice Steel rims, factory silver Incl. Electrics 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Additional LED work light(s) at the rear, switched via reversing light Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Support legs coated black Attention: Archive pictures!

Condition: good (used), Interchangeable jaws, top jaws, three-jaw chucks, segment jaws, clamping jaws, stepped block jaws, stepped top jaws, block jaws, base jaws, interchangeable jaws, wedge bar chucks, interchangeable jaws, power chucks -Top jaws: hard top jaws for key bar chucks, helical toothed -Jaw width: 26 mm -Dimensions: see photo technical drawing -Dimensions total: 115/78/H70 mm Kjdsxdip Hspfx Ab Uodw -Total weight: 3.2 kg

Condition: new, Year of construction: 2025, functionality: fully functional, cutting height (max.): 210 mm, cutting width (max.): 2,120 mm, cutting length (max.): 9,200 mm, saw drive: 15,000 W, total length: 11,000 mm, height adjustment type: electric, overall weight: 2,500 kg, saw blade diameter: 550 mm, JRIMAC rip saw "TOP" - NEW - - Cutting length 2200 - 9200 mm - Cutting width 420 - 2120 mm - Cutting direction left - right (right - left on request) - Cutting height max. 210 mm with high-quality saw blade Ø 620 mm. - Precise and clean cut due to strong, self-supporting welded construction of the machine stand. - Carriage guidance via linear guides, with ball-bearing mounted, maintenance-free rollers. Kodjgk Nvnopfx Ab Ujdw - Safety beam mounted above the machine table with 6 mm thick lamella protection. - Extraction connection Ø 160 mm installed at table height at top right and bottom left ready for connection. - Flexible and efficient working thanks to 250 mm opening of the slat guard above the top edge of the table. - Infinitely variable, frequency-controlled, powerful feed of the carriage. - The maximum feed speed can be adjusted. - Automatic stepless saw blade height adjustment. - Infinitely variable width stop adjustment via several operating levers. - Electronic positioning control. - JRIMAC" saw blade quick clamping system allows quick saw blade changes. - Cut release as standard (small mobile foot pedal). - Front table supports made of wood, plastic or Pertinax coating. - High work safety. - Only high-quality components are used and installed. - The electrical control cabinet is easily accessible at the front of the machine. - The machine electrics are designed for 230/400 volts, 50 Hz. - BG dust-tested - EC type-tested in accordance with Directive 2006/42/EC - Forcibly guided splitting wedge - Processing of more than 12 different materials possible - Reliable spare parts and customer service

Condition: used, functionality: unexamined, Year of construction: 1999, machine/vehicle number: 26579, control type: PLC-controlled, bending force (max.): 110 t, working width: 3,050 mm, pressing force: 110 t, working length: 3,050 mm, Used press brake 110 tons 3 meters 6 axes Technical specifications Voltage: 400 V Model: PPEB 110/30 Pressing force: 1100 kN Working length: 3050 mm Distance between uprights: 2600 mm Stroke: 200 mm Table/ram gap: 400 mm Throat depth: 400 mm Approach speed: 130 mm/s Working speed: 12.4 mm/s Return speed: 115 mm/s Motor: 15 kW Oil capacity: 250 liters Machine weight: 9500 kg Kdodpfsw Afccjx Ab Uow CNC control: CADMAN Table width: 150 mm Noise level: 80 dBA Pump flow rate: 38 l/min Pump type: Voith IPV 4-25 High precision and flexibility. The PPEB press brake is a robust, highly technological machine. PPEB gives you the freedom to configure your press brake according to your production requirements. Automatic crowning The crowning system compensates for machine deflection to ensure accurate and repeatable bends. Our wedge system is custom-made for every machine, representing crowning across the entire table length. Robust structure A single-piece welded frame ensures machine accuracy.

Year of construction: 2018, condition: excellent (used), The wedging and coring machine OS12 for citrus has been designed to core and slice oranges into segments. The structure consists of a rotating plate with 8 workstations for fruit. Above the plate, on the opposite side to the loading side, we find the mechanisms for the two operations. The first mechanism moves up/down by means of a pneumatic piston and allows rotation of the coring tube by means of a three-phase electric motor. The core tubes are interchangeable. The second mechanism always moves up/down by means of a pneumatic piston and is equipped with pads that push the fruits through the die-cutters, allowing them to be cut into wedges. The plate rotates at regular intervals and at the speed chosen by the customer; when the plate stops, the three work operations take place at the same time: the operator loads the fruit and the two mechanisms perform the coring and cutting operations. The OS12 machine consists of welded tubes, on wheels (with brakes) to allow easy movement. The machine is equipped with a stainless steel electrical panel with PLC and inverter for the synchronization of operations. Advantages: • High cutting quality • Very robust machine structure • Compact size • Simple and fast maintenance of the machine • Easy sanitation • Electrical panel built according to EEC/IP 65 standards • Option: self-locking rotating wheels It is equipped with: 2 Slides for the product and for the waste. Ksdpfowdgp Tjx Ab Usdw

Condition: used, Technical details: bore capacity in steel (diameter): 30 mm throat: 260 mm bore stroke: 160 mm spindle taper MT: MK3 feed steps: 0,1; 0,2; 0,3 mm/U und manuell spindle speed:: max. 1800 stufenlos U/min Distance spindle/table max.: 750 mm table clamping surface:: L: 280 x B: 355 mm table rotating: nein ° clamping table - swivable: 360 Grad drill table adjustment: vertikal: 600 mm column diameter: 130 mm threading: Nein / no total power requirement: 1,1 kW weight of the machine ca.: 570 kg dimension machine xH: 0,9 x 0,9 x 1,9 m This machine has 2 tables. Drilling table LxW: 370 x 500 mm Attachment table: LxW: 420 x 750 mm Clamping surface = 320 x 600 mm, transverse displacement (X-axis) 250 mm possible Ejection of tool via ejector wedge accessories: vice Kdjdova Higopfx Ab Usw machine base *

Condition: new, machine/vehicle number: 28b2dda4ac4da850b1010673a, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, fifth-wheel plate with replaceable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with guide wedges on both sides, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 20 foot container (Note! low fifth wheel load for 20 foot containers) 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Free support foot corner dimension or free swing radius to the rear approx. 1850 mm 2 wheel chocks with holder Half-shell mudguard with anti-spray flaps according to EG Hydraulics Kedpfx Aji Ri Eueb Ujdw Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK Screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension 3 SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons Gross train weight Air suspension. Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck instal. calibrated scales) Wheels and tires 6 385/65 R22.5 tires of the manufacturer's choice 6 steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Country of registration/ plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Support legs coated black Attention: Archive pictures!

Condition: used, Year of construction: 2000, greates pass round over bed 1050 mm centre distance 8000 mm turning diameter over slide 730 mm turning length 7770 mm control Heidenhain Manual Plus spindle bore 215 mm 3-jaw chuck Forkardt F630 number of speeds 3 speeds 2-80/ 32-224/ 90-800 U/min weight of the machine ca. 13,5 t dimensions ca. 10500 x 2400 mm Large spindle clearance (215 mm)! 4-fold turret (quick-change holder) PARAT with various interchangeable cassettes Ksdpfsud Ak Njx Ab Uodw Chip conveyor Steady rest with rolling element, 500 mm clearance Three-jaw wedge bar chuck Forkardt, Ø 630 mm Motorized tailstock adjustment Chip back wall moving chip guard without drill rod!

Condition: good (used), Year of construction: 1961, Heavy-duty lathe, turning machine, lathe, center lathe, center lathe -Condition of machine bed: very good condition -Machine bed: hardened -Manufacturer: Martin, lead screw lathe type DLZ 502 Kdjdpfowfpilsx Ab Uow -Turning length: 2200 mm -Turning Ø over bed: 580 mm -Turning Ø over support: 300 mm -Spindle bore: Ø 65 mm -Spindle speeds: 22.4 - 1000 rpm -Wedge bar chuck: Forkardt Ø 320 mm -Tailstock mount: MK5 -Drive: 7.5 kW -Accessories: 4x bezels, tool holder, tools see photos -Dimensions: 1260/3720/H1260 mm -Weight: 2510 kg

Condition: used, Pneumatic Single-Column Press RECTUS - FRIEDMANN & MAIER Type K3000 / 50 / 6A Air-Powered Press Serial No. 3437 Year of manufacture: approx. 1990 Press force: 3.0 tons at 6 bar Press force: 2.6 tons at 5 bar Press force: 2.2 tons at 4 bar Press force: 1.6 tons at 3 bar Press force: 1.0 ton at 2 bar Throat depth: 150 mm Power stroke: 6 mm Pre-stroke: 50 mm Total stroke: 56 mm Ram surface: Ø 100 mm Tool mount: Ø 12 mm Installation height: max. 180 mm Kdedpfx Abow A Srwe Uew Table area: 200 x 200 mm Compressed air requirement: max. 6 bar - Pneumatic power cylinder with mechanical power amplifier (wedge-lever principle) - Press cylinder height adjustable on the frame via threaded spindle (50 mm) - Without pneumatic control system - Throttle valve for stroke speed adjustment Required space (L x W x H): 440 x 230 x 750 mm Weight: 127 kg Good condition 2 units available, price per unit

Condition: like new (used), functionality: fully functional, mileage: 657,810 km, power: 228 kW (309.99 HP), first registration: 07/2001, Year of construction: 2001, New engine, 3rd steering axle, Cofaral superstructure, Mechanical transmission, Total tank capacity 12,850 L, Water capacity 4,500 L in side compartments, Automatic rear tank bottom closure with wedges, Jurop PR150 decompressor 15,000 L/min, Spaggiari high-pressure water pump 190 bar 171 L/min, Main hydraulic reel Bandiera 3/4, Side hydraulic reel 1/2. Kedpfx Aexpnbxjb Uedw

Condition: used, Year of construction: 1957, Technical details: bore capacity in steel (diameter): 32 mm arm length:: 1000 horizontal adjustment of the boring slide: 700 mm vertical adjustment of arm: 600 (motorisch) mm swivel range of the arm: 90° rechts/links Grad distance table - lower edge spindle: min./max.: 200 / 1120 mm spindle taper MT: 4 bore spindle stroke: 420 (manuell-automatisch) mm range of revolutions per minute - continous: 20 - 2000 / 3 step U/min feed: 01, / 0,2 / 0,3 / 0,4 / 0,8 / 1,2 mm/U column diameter: 250 mm base plate surface area: 1100 x 600 mm total power requirement: 4,6 kW weight of the machine ca.: 2,5 t dimension machine xH: 1,8 x 0,8 x 2,5 m Ksdpfx Abevhbpqj Uedw Tool ejection via expulsion wedge Equipment: Coolant system with pump (without feed) Drill cube L: 760 x W: 500 x H: 510mm / horizontal surface 760 x 500mm and vertical surface 760 x 510mm Machine ilumination *

Condition: used, machine/vehicle number: d25bedc76ae946ce00df59d5c, empty load weight: 11,600 kg, maximum load weight: 35,900 kg, overall weight: 47,500 kg, axle configuration: 3 axles, first registration: 06/1982, tire size: 9,5 r17,5 zwilling, Further information 1st axle rigid, 2nd + 3rd axle hydr. positively steered with saddle deflection wedge, 1 pair of hydr. support legs incl. hand pump for emergency operation, leaf suspension, 6 storage compartments, steel riffle plate complete, air: red-yellow + electrics: 1x 7-pin Kodpfx Asi Riyzob Uodw Length of gooseneck approx.: 4,380 mm Length drop deck approx.: 11,300 mm Saddle height approx.: 1,200 mm