Core shooting machine

Roeper H80

Condition: used, Year of construction: 1987, pressure / t stroke / mm table-size / mm weight of the machine ca. 65000 kg Make: Shepherd Type: SVRM 4-roller bending machine: Year of construction: 1986 Working width: 3000cm Hfsdpfxjuddcao Ad Reg Smallest pipe diameter with 600 mm roller: Ø 720 mm Smallest tube diameter with 360 mm roller: Ø 460 mm Sheet thickness up to (depending on the material): 50 mm Material SA- 738 B Working width: 2500 mm Material SA- 738 B Material thickness: 35 mm conical bending: Except for the top roller, all rollers can be moved in an inclined position for conical bending. The roller positions can be read on display instruments. For semi-automatic or fully automatic operation of the machine, the bearing jewels of the rollers are equipped with scale bars and slide cams for limit switch actuation. This allows the rollers to return to the same set position over and over again, giving a very high level of uniformity in the shot wefts being bent.

Condition: used, Year of construction: 2010, Overview   This ARCADE GEL 6 bottle washer was built in 2010 by the German manufacturer GM Gera. The machine is still in operation and can be inspected in person at any time. The ARCADE GEL 6 is fully functional and must be replaced due to an increase in performance.   Technical details   Nominal output: 33,000 bph   Control range: 13,200 - 36,300 bph   Chain pitch: 169 mm   Cell pitch: 110 mm   Bottle cells per row: 30 pieces   Total bottle cells: 7,860 pieces   Bottle cells, loaded: 7,680 pieces   Consumption  Compressed air: 1m³   Steam (operation): 489 kg/ h   Steam (heating): 4,430 kg/ h   Electrical power: 48.4 kW   Water: 7.35 m³/ h   Bath volume   Pre-soak: 2,263 l   Pre-caustic: 7,240 l   Caustic 1: 31,755 l   Caustic 2: 350 l   Hot water 1: 350 l  Hot water 2: 350 l   Cold water: 350 l  Hfjdet Ul Exspfx Ad Rog

Condition: refurbished (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 30214501, turning length: 2,000 mm, total length: 12,000 mm, WFL Millturn M60/2000 WORKING RANGE Hfodju Hl R Topfx Ad Rsg center distance mm 2000 swing over bed, turning diameter mm 690 MAIN DRIVE AC-drive with 2 gear steps drive power 100% duty cycle kW 40 max. speed min-1 3300 max. torque at the spindle 100% duty cycle Nm 1830 TAILSTOCK quill diameter mm 140 quill travel mm 160 quill force (adjustable) N 3500-31000 quill with installed live center MK 5 TOOL HOLDER (single tool holder, turning-boring-milling unit) AC-drive drive power 100% duty cycle kW 30 speed range max. min-1 6000 max. torque at the spindle 100% duty cycle Nm 315 travel vertical to the X/Z-plane (Y-axis) mm 300[-125/+175] pivot capability of the milling spindle (B-axis) ° -110/+90 spindle head acc. DIN 69893 HSK-A100 spindle diameter in front bearing mm 100 DIMENSIONS length (max. tool magazine) m 11 width/height m 3,9/3,3

Year of construction: 2007, condition: excellent (used), 603 LBH Technical Description Main Technical Specifications • Minimum sawing capacity at 90° min.mm 60 x 10 max.mm 610 x 310 • Sawing capacity at 45° mm 400 x 310 • Sawing capacity at 60° (available on two flanges only with relevant option) mm 250 x 250 • Mitering angles +45° / -60° • Toothed band size mm 34 x 1.1 • Toothed band speed m/min. 78 Hedpfx Aol Si Uusd Rjfg • Band motor power kW 4 • Working level height mm 850

Condition: used, Lasko hammer KGK 063 Impact force 630 mkp Stroke max. 630 mm Bear weight 630kp Hfedsu Eb Nispfx Ad Rjg Top pressure - filling pressure 5 bar

Condition: used, Year of construction: 2002, Overview This PET bottling line was built between 2002 and 2013 by the German manufacturer Krones and is designed for bottling still and sparkling water in PET bottles with an Alaska neck finish. The line is in production until September 2025 and can be viewed in operation by prior appointment. Technical details Output: 22.000 bph (the nominal speed at 0.5 is 25.000 bph) 60 rinsing nozzle 80 filling valves 15 capping heads Product: Water Container material: PET Neck format: Alaska Label type: OPP Capper brand: Zalkin Years of manufacture: 2002, 2009, 2013 Scope of delivery  Compressor: Atlas Copco ZD2300VSD (2009) Blowing machine: Krones Contiform S14 (2009) Air conveyor: Eurosistemi (2002) Filler: Krones Volumetic, Variojet (2002) Labeler: Krones Contiroll (2013) Hsdpswqpgzsfx Ad Rsfg

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036936, clamping force: 800 kN, screw diameter: 35 mm, displacement volume: 135 cm³, injection pressure: 1,837 bar, injection weight: 123 g, mold height (min.): 150 mm, ejector force: 22,000 N, ejector stroke: 100 mm, opening stroke: 750 mm, installation height: 400 mm, total length: 4,750 mm, total width: 1,670 mm, total height: 1,820 mm, overall weight: 5,900 kg, heating capacity: 8.9 kW (12.10 HP), drive type: Vollelektrisch, clear span: 470 mm, tool weight: 600,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The basic injection molding machine, precisionMolding, offers the perfect entry-level solution for all-electric injection molding, enabling you to react quickly and innovatively to market requirements. It combines high performance, simple operation and short delivery times. It can be used in a wide range of applications, e.g. in the packaging industry, the electrical and electronics industry, medical technology and the automotive industry. Your benefits: - Optimized price-performance ratio for a wide range of applications - High energy efficiency thanks to all-electric machine concept - Realization of demanding delivery times thanks to basic machine concept with a wide range of options TECHNICAL DATA: KM 80 / 250 PA G01 (order 38670013) (machine no.: 61036936, new, year of manufacture 2023) CONTROL  MC P1 with 15" TFT color screen with multi-touch functions CLAMPING UNIT  Clamping force kN 800  Mold opening force, max kN 120  Clear width (h x v) mm 470 x 420  Clamping platen (h x v) mm 610 x 560  Tool installation height min. - max. mm 150 - 400  Opening width mm 750  Mold opening stroke max. mm 350  Ejector drive electric  Ejector stroke mm 100  Ejector force forwards/backwards kN 22 / 22  Ejector speed forwards/backwards mm/s 300 / 300  Max. Mold weight kg 600 SPRING UNIT  Screw diameter / type mm 35 / standard  Effective Ls/D ratio 20.0  Injection pressure bar 1837  Stroke volume cm³ 135  Shot weight at max. stroke for PS g 123  Injection speed mm/s 200  Injection flow rate cm³/s 192  Screw drive/speed 1/min 382  Plasticizing flow (standard screw)4) g/s 19.5  Nozzle contact force kN 30 ELECTRICAL PARAMETERS  Connected load kW 17.8  Installed heat output kW 8.9  Power supply V / Hz 400 / 50 3 phases with neutral conductor WEIGHT AND DIMENSIONS  Net weight with switch cabinet t 5.9  Length x width x height m 4.75 x 1.67 x 1.82 ADDITIONAL EQUIPMENT  Low-wear plasticizing  BluePower fully insulated plasticizing cylinder  Open nozzle  Air valve 1 - fold (BWAP) Hjdpfxsuggb Do Ad Rjfg  Pneum. Control hot runner valve gate 1 - compartment  Electrical interface cascade 4-fold  Electrical preparation for hydraulic auxiliary unit  Euromap interfaces handling E18, E63  Euromap interface (central computer) E67, E77  Water battery 4 - compartment  Automatic central lubrication  Adaptive Process Control (APC)  Spray embossing circuit  Graphic analysis package  Swivel device Injection unit The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your inquiry.

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036946, clamping force: 800 kN, screw diameter: 40 mm, displacement volume: 201 cm³, injection pressure: 1,860 bar, injection weight: 183 g, mold height (min.): 150 mm, ejector force: 22,000 N, ejector stroke: 100 mm, opening stroke: 750 mm, installation height: 400 mm, total length: 4,750 mm, total width: 1,670 mm, total height: 1,850 mm, overall weight: 5,600 kg, heating capacity: 11.5 kW (15.64 HP), drive type: Vollelektrisch, clear span: 735 mm, tool weight: 600,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The basic injection molding machine, precisionMolding, offers the perfect entry-level solution for all-electric injection molding, enabling you to react quickly and innovatively to market requirements. It combines high performance, simple operation and short delivery times. It can be used in a wide range of applications, e.g. in the packaging industry, the electrical and electronics industry, medical technology and the automotive industry. Your benefits: - Optimized price-performance ratio for a wide range of applications - High energy efficiency thanks to all-electric machine concept - Realization of demanding delivery times thanks to basic machine concept with a wide range of options TECHNICAL DATA: KM 80 / 380 PA G01 (order 38670023) CONTROL  MC P1 with 15" TFT color screen with multi-touch functions CLAMPING UNIT  Clamping force kN 800  Mold opening force, max kN 120  Clear width (h x v) mm 470 x 420  Clamping platen (h x v) mm 610 x 560  Tool installation height min. - max. mm 150 - 400  Opening width mm 750  Mold opening stroke max. mm 350  Ejector drive electric  Ejector stroke mm 100  Ejector force forwards/backwards kN 22 / 22  Ejector speed forwards/backwards mm/s 300 / 300  Max. Mold weight kg 600 SPRING UNIT  Screw diameter / type mm 40 / standard  Effective Ls/D ratio 20.0  Injection pressure bar 1860  Stroke volume cm³ 201  Shot weight at max. stroke for PS g 183  Injection speed mm/s 200  Injection flow rate cm³/s 251  Screw drive/speed 1/min 334  Plasticizing flow (standard) g/s 24.7  Nozzle contact force kN 34 ELECTRICAL PARAMETERS  Connected load kW 20.6  Installed heat output kW 11.5  Power supply V / Hz 400 / 50 3 phases with neutral conductor WEIGHT AND DIMENSIONS  Net weight with switch cabinet t 5.6  Length x width x height m 4.75 x 1.67 x 1.85 ADDITIONAL EQUIPMENT  Low-wear plasticizing  BluePower fully insulated plasticizing cylinder  Open nozzle  Air valve 1 - fold (BWAP) Hfedsud H Dmspfx Ad Rjg  Pneum. Control hot runner valve gate 1 - compartment  Electrical interface cascade 4-fold  Euromap interface handling E18, E63  Euromap interface (central computer) E67, E77  Water battery 4 - compartment  Automatic central lubrication  Adaptive Process Control (APC)  Spray embossing circuit  Graphic analysis package The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your inquiry.

Condition: excellent (used), Multi purpose oven with gas and steam heating. 2m wide belt. Superb condition, the best one we have seen of this model. Direct from closed meat free factory. The Revoband oven features precisely controlled vertical hot air directed at the product from above and below the belt. We designed the oven with adjustable fan speed control for each zone to provide unlimited flexibility. Perfectly suitable for chicken fillets, wings & drumsticks, burgers, nuggets, fish sticks, back bacon, sausages, lasagna and other special applications FEATURES & BENEFITS High Velocity air provides consistent color development and uniform cooking results Precise control of temperature and production time for repeatable results Cook with steam and elevated temperature or steam only for process flexibility Indirect heat eliminates by-products of combustion for product zone. Hfedpsrd Rqkefx Ad Rjg

Condition: new, 7 pieces heating coil new for a melting furnace Fulmina SOU 20E, Technical data: Reversible element with connection ends Ø 10 x 270 mm power: 10.000 Watt Voltage: 220 Volt cold resistance: 4,60 (± 5%) Ohm wire diameter: 4,50 mm coil inner Ø: 29 mm leg length: 240 mm Number of legs: 3 x 8 pieces Wire quality: CrFeAl Y 3 heating coils are a complete set in this model (the pictures of the melting furnace serve the representation and show the model in which the heating coils were installed, they fit however also into other models with smaller or higher achievement, it changes only the number of pieces) immediately available from stock Hodjd Tx A Espfx Ad Rsfg