Tos Svitavy PKSN32 tracked multi-pilot

TOS Svitavy PKSN 32

Condition: good (used), I sell the multirip saw of czech production TOS Svitavy PKSN32. Cutting height under the blade 120mm / possibility of adjustment Hodpfxomk E D Io Aaaenk Width of cut on the feed belt max. 350mm. Open design / possibility to insert wider workpieces Motor approx. 45 KW. Diameter of main saw blade max. 350mm. Feed speed controlled by variator up to 36 m/min. Total weight approx. 3500kg. Blades and adjusting rings included. The machine is in stock in Kežmarok, Slovakia. Available immediately.

Year of construction: 2011, condition: used, functionality: fully functional, Finger jointing line for cross sections up to 200 cm² (80/240 mm or 100/200 mm), with the following. components: 1. HOWIAL tilt unstacking - SH/4t - 1,75x1,75x6,00m - 4t - short. Length 2,50 m, semi-automatic separation of the package. For tilting the wood pile up to 45°. Electric motor drive. stack dim. max. 1,75 x 1,75 x 6,00 m max. stacking load 4 t shortest wood length 2,5 m 2. HOWIAL - VE 1 lamella separator for crosscut saw. With pneum. controlled tongues, on which the material is marked for defects, deposited on the roller conveyor below. 3. HOWIAL - evaluation roller conveyor RO-1 digital wood moisture measuring, control and recording system for autom. recording and control of wood moisture in cycle measuring method according to electric resistance principle. 4. gann DMT-8 dig. Wood moisture measuring, control and recording system for automatic detection and control of wood moisture in the cycle measuring method according to the electrical resistance principle. Plant in large switchboard complete with ink jet printer. 5. HOWIAL - crosscut saw AS-30 B pneum. Under table crosscut, with 2 autom. feed units, autom. crosscut. Special photocell control for detection of fluorescent line markings. Automatic waste disposal possible. Saw motor power 7,5 kW saw blade diameter 700 mm feed drive approx. 2 x 1,5 kW Air pressure 8 bar feed speed max. approx. 60 m/min. 6. HOWIAL - conveyor belt cut off waste, with studded belt and guide plates belt width 350 mm belt 2000 mm long belt speed 0,4 m/sec. Hnjdpoi Ezx Dofx Aaaok 7. HOWIAL - double roller conveyor RO-2 6,00 m long incl. transversal transport, drive by round belt, all rollers driven. Cross transport chain conveyor. Ejection ± moisture right Transport speed adjustable 100 m/min. length approx. 6,00 m Width of rollers approx. 400 mm Diameter 112 mm 8. compact finger jointing machine Cook Bolinder The technical data are original from Cook Bolinder: wood width from 75 to 245 mm Timber thickness from 20 to 105 mm Input lengths from 1m to 6 m Cross sections from 30 cm² to 200 cm² Pressing force 5 - 22 to Spindle diameter 50 mm tine profile 15/15 spindle speed approx. 6000 upm Total electrical connected load approx. 62 kW Machine weight approx. 9 to. Gluing OEST comb system for PU Modern Telemechanique SPS control. 9. HOWIAL - Roller conveyor with destacking system Driven roller conveyor with autom. ejector and hydr. driven destacking arms. Technical data: H: 920 mm L: approx. 12.000 mm 10. safety fences incl. circuit breaker 11. finger joint testing machine BSPLT-100 Testing machine for finger joint bending test according to DIN 1052-1/A1 and EN 385 Support distances freely adjustable, attached dimension scale, autom. calculation of support distances in the software. Fully automatic test procedure by mouse click on PC (not included). Alternatively, the test procedure can be started by key operation on the front panel. Connection of any commercially available PC or laptop (Win 2000/XP) via the supplied RS232 serial cable. Fully automatic measured value logging as well as automatic logging in MS-Excel with graphical display. Representation max. wood width: 300 mm max. wood thickness: 140 mm max. compression force: < 100 kN max. support length: 2100 mm Measuring accuracy WITHOUT DISMANTLING

Condition: reconditioned (used), Year of construction: 2001, , Basic information Manufacturer TOS SVITAVY Type PKSN 32 B Category Multiripsaws Shipping Delivery to be agreed Terms Technical parameters Maximum Working Width #### mm 400 Machine with simultaneous transport and processing of the element The machine is CE marked Used machine Minimum Working Length #### mm 330 Engine power #### kW 55 Supply voltage #### V 380-400 Safety Guards Completely renovated Electrically Controlled Adjustments Technically efficient Perfect condition Shank Diameter #### mm 70 With one tool spindle With noise reduction housing Cast iron body Feed Speed #### m / min 36 Spindle Lock Maximum cutting height #### mm 160 New Electricity New Mechanics Hsdpfx Ajhixkhjaasnk New Pneumatics New Painting Noise Level #### Db 70 Right and Left Rotation Automatic adjustment Very good condition Cutting width #### mm 400 Machine width #### mm 1800 Machining Width Saw blade diameter #### mm 400 Machine weight #### kg 3500 Machine dimensions #### x #### x #### mm 1600x1800x2500 Cutting Height Machining height #### mm 160 With freely adjustable speed With the transport of the element in the machine

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, SCM Morbidelli N100 CELL Working area X: 4,286 mm Working area Y: 2,185 mm Working area Z: 150 mm Vertical drilling heads: 12 Horizontal drilling spindles X: 4 Horizontal drilling spindles Y: 2 1 grooving saw blade in X Tool changer: 20 positions Hnedjx Tgubspfx Aaaek Barcode reader 3 vacuum pumps SCM eye-M control system Good condition

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) 22” color monitor, IBM computer, printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Functional description: 1. filling the autoclave with wood 2. creating a pre-vacuum 3. filling with gas 4. heating 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Hjdpfxjv Si Szo Aaajnk Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: good (used), Year of construction: 2006, machine/vehicle number: 108111, functionality: fully functional, working width: 240 mm, planing height: 160 mm, working height: 180 mm, Four-sided planer after service inspection, machine weight 3900 kg Hnedpfxjvrq U Dj Aaaek

Condition: excellent (used), TECNI-ARMENTIA CH-70 edger - hydraulic control - the possibility of programming the width - saving up to 12 programs - centering table TECHNICAL PARAMETERS: cutting width max. 700 mm cutting height max. 130 mm main engine power 55 kW material width max. 830 mm length of the fixed sleeve 300 mm length of the movable sleeve 100 mm min. material length 700 mm Hedpfx Ajidmptoaasnk spindle diameter 65 mm sleeve diameter 85 mm disc diameter 350 - 400 mm hydraulically smoothly adjustable feed feed speed up to 38 m / min feeding table 2700 mm roll width 700 mm roll diameter 140 mm centering feeding table two lasers pump motor power 4 kW row of anti-recoil pawls three upper pulling rollers three lower pull rollers hydraulic pressure hydraulic height adjustment dimensions (length / width / height) 480/200/230 cm weight 4000 kg

Condition: excellent (used), Year of construction: 2020, HPPA through-feed press manufactured by Famad Paczków, year of manufacture 2020. Hnodsvla A Dspfx Aaask The press is designed for through-feed gluing of door packs, MDF boards, plywood, veneer, etc. It features a pneumatically lifted chain conveyor for loading and unloading, and can operate independently or as part of a production line.

Year of construction: 1988, condition: like new (used), Location Kłodawa 66-415 Conditions of delivery OWN RECEIPT Cost of delivery Customer cover Start type to be agreed Description Comments Four-sided planer, banding machine, Gabbiani spichetting machine Max planing width: 160 mm Max planing height: 100 mm Min. Element length: 180 mm Spindle diameter: 30 mm Number of spindles: 6 Spindle order: down rights, left, Mountain, Mountain bottom Crawler feed: top, bottom Smooth infeed adjustment: 4 - 34 m / min It is possible to work feed at an angle of: 0 ° - 30 ° Feed on cardanach Manual spindle height adjustment Adjustable heads in all directions Automatic lubrication of the track All bearings replaced with Teflon Machine after a full review The machine is adapted to the production of parquet and slats Dust Extractors: 6 x 120 mm Hodpedx Elmsfx Aaaonk Power supply: 400 V Total power: 26.2 kW Dimension of the machine Length: 4060 mm Width: 1500 mm Height: 1200 mm important: planed tables in the whole machine and leveling, setting angles and

Year of construction: 1985, condition: ready for operation (used), Double-sided tenoning machine for parquet FOD Hnodpfx Ajilc Ncoaask DOUBLE-SIDED for parquet production, it has a face leveling saw and a vertical cutter for the production of a groove