Circular saw

ULMIA 1710 SN

Condition: used, Year of construction: 2025, operating hours: 2 h, Operating hours: 2 New tractor with dealer daily registration prior to delivery Standard equipment / technical data Engine Rated power (ISO): 82 / 110 kW/hp at 2200 rpm Maximum power: 86 / 115 kW/hp at 2000 rpm Maximum torque: 460 Nm at 1600 rpm Manufacturer / Type: Agco Power / AP 44MBTN-D5 Low-emission engine, 4-cylinder / 4.4 l, 4 valves, STAGE 5 Regulated turbocharger, SCR catalytic converter DOC – Diesel oxidation catalyst SC soot particle filter One-piece, tiltable engine hood Exhaust on right side, in front of cab Fuel tank capacity: 198 liters / AdBlue: 18 liters Transmission / PTO 16/16-Speed Dyna-4, SpeedMatching, 40 km/h PowerControl left-hand operation with powershift reverser, 4-step powershift Permanently cooled wet multi-plate clutches with independent lubrication system Dual-speed PTO: 540 / 540E / 1000 rpm Electronic shift in cab PTO START/STOP button on left rear fender Hydraulics / Rear linkage Open Center system, 58 l/min total flow, max. 200 bar 2 control valves with hydraulic couplers: 1x single/double-acting, pressure relief + 1x single/double-acting, neutral leak, SST Category 3 quick coupler with balls and catcher bowls CAT 3/2 Lower link draft control 5,200 daN maximum lift force, 2 external lift cylinders Dksdpeyvmq Ijfx Affsk Adjustable lift rods on both sides and 2 side stabilizers EHR with external operation on both rear fenders Electrical equipment Thermostart, 120 A alternator Electric battery isolation switch 12 Volt power supply for external devices with socket Axles / Additional weights Rear axle ND with flange hub Oil-cooled disc brakes Height-adjustable automatic drawbar Rear fender outer width 2.00 m, without extensions Front weight carrier with integrated drawbar and towing pin Driver's station Standard cab with vibration damping, standard roof, ventilation and heating, air conditioning Integrated safety frame with tinted glass Doors on both sides with safety steps Adjustable steering column (height & tilt) Air-suspended driver's seat with armrests, swivel adapter, and seat belt 2 large telescopic exterior and wide-angle mirrors Interior mirror Analog-digital dashboard (SIS) Radio pre-wiring with antenna and speakers 4 work lights each at the front and rear of the cab roof 2 headlamps each in the engine hood and on the handrails, 2 work lights on rear fenders Rear window washer/wiper All-wheel front axle with selectable differential lock Special equipment With fuel tank protection PowerControl & brake to neutral (clutch effect) 100 l/min Open Center hydraulic system oil flow sharing (58+42 l/min) Leak oil collector at quick couplers 3 control valves: 1x pressure relief, double-acting, float, SST + 1x double-acting, neutral leak, SST + 1x double-acting, neutral leak, SST + free return 2.5 t front linkage, 1 hydraulic hose set, electrical socket 480/70R38 ADJ Ø1.69m & 380/70R28 ADJ Wide rear fender extensions Air conditioning Cab with mechanical suspension Telescopic exterior and wide-angle mirrors Passenger/instructor seat with belt Air-suspended driver's seat, automatic setting with seat belt, swivel adapter, and armrests Rear window washer/wiper Automatic battery isolation switch, 12

Year of construction: 1999, condition: excellent (used), 1999 Start type: to be agreed Cost of delivery: Customer cover Conditions of delivery: Dksdsd Nmdkjpfx Affjk OWN RECEIPT Category: Grinding machines in Poland Subcategory: Through grinding machines Subcategory 2: Grinding machines, brushing machines Description Manufacturer VANGROENWEGHE Model / type of TYPE M-300-COMBI / CE machine

Condition: new, Year of construction: 2026, This machine is a powerful, precise and universal device in a compact body, created for all workshops, furniture manufacturers and carpenters looking for a powerful machine. This model features many solutions implemented in more expensive models. Fantastic value has been achieved without any compromises when it comes to its quality and universality. Precise saw cutting and height adjustment through a knob Parallel guide with microadjustment Table ground, made of cast iron with expansion capability Stable, uniform table saw design, intended for any carpentry work Integrated side table provides great cutting capabilities Dkodjvxhlgepfx Affsk Technical data Maximum saw diameter 254 mm Saw speed 4000 rpm Saw tilt range 90–45° 45º maximum cutting depth 50 mm 90º maximum cutting depth 80 mm Worktable dimensions 350×800 mm Movable table dimensions 240×1320 mm S1 continuous work motor power 2.2 kW Power supply 400V Weight 180 kg Dimensions 1550×1900×820 mm

Condition: new, NEBES TM 275 Band Saw Machine - 400 v Three-phase NEW "CE" INDUCTION motor Cast iron structure Adjustable cutting angle from 0° to 60° All cast iron structure Electric pump for blade lubrication and cooling Oil-bath blade tensioning gauge Front controls and two cutting speeds Deviator for exclusion of coolant pump Blade guide with carbide skids (H.M.) Round cut 0° 220 mm Square cut 0° 200 x 200 mm Flat Cut 0° 230 x 185 mm Round cut 45° 150 mm Square cut 45° 150x150 mm Flat Cut 45° 150x200 mm Round Cut 60° 90 mm Square Cut 60° 90x90 mm Flat Cut 60° 90x120 mm HP 1.3 Dksdpfx Ajh Nm Nceffjk Voltage 400 V Blade size 2450 x 27 x 0.90 mm Weight 265 kg

Condition: used, Year of construction: 1966, Swivelling spindle: No Height adjustment: Handwheel Swivel adjustment: - Cutter jaw adjustment: manual Height display: Scale Swivel angle display: - Fence indicator: Scale Spindle diameter: 30 mm Speeds: 2800, 4500, 6000, 5600, 8000, 12000 rpm Motor power: 4 / 5.5 kW Motor brake: Manual Extraction connection: 2 x 120 mm Machine length: 2000 mm Machine depth: 900 mm Dkodpsxu Dhlefx Affok Weight: 700 kg

Condition: new, table length 430 mm table width 240 mm x-travel 225 mm y-travel 160 mm table height 160 mm T-slots 12 mm weight 45 kg dimensions 0,6 x 0,45 x 0,2 mm Dsdpfxoupw T Re Affekk Cross table with turntable

Year of construction: 2026, condition: as good as new (ex-display), Workbenches in Pro version Precise and careful processing Completely made of steamed, solid beech All important edges are rounded Environmentally friendly oiled surfaces Standard with tool drawer The two cylinder rods of the collets are precise and stable in a casting With smooth trapezoidal threaded spindle French front caliper with German rear caliper with linear Guide, two round bench dogs short, long, two round bench dogs drawer and loading in Finger hot dip galvanizing in rear caliper and by charging back 1915 mm long work surface without pliers Width/depth work surface without pliers 615 mm Working height 870 mm Length 520 mm front caliper Length 450 mm rear caliper Wide front caliper 70 mm Dkedoc Uydajpfx Affsk Wide rear pliers 140 mm Span front pliers 190 mm Span back pliers 180 mm Span front clamp until the Middle Hook 225 mm Span back pliers until the Middle Hook 265 mm Plate thickness 50 mm Length 2120 mm (product) Width/depth (product) 790 mm Height 870 mm (product) Weight 91 kg (net) Location: Off the shelf 54634 Bitburg

Condition: excellent (used), Year of construction: 1982, Table saw ULMIA 1710s Year of construction 1982 Tilting angle 45° Djdoufgnzjpfx Affskk Cutting length on cart 750mm Blade diameter max 250mm. Cutting height 75mm. Cutting width between the saw and the attachment 650 mm Scale carriage for cutting angles Table size 1000x630mm

Year of construction: 1979, condition: good (used), Underfloor circular saw, crosscut saw, pull saw, miter saw, panel saw, table saw, aluminum circular saw, panel saw Dodpfx Aehfufgjffjkk -Manufacturer: Martin, panel saw type T 70 with automatic feed -Engine power: 11 kW -Speed: 1445 rpm -Saw blade: Ø 410 x 5 mm -max. Cutting height: 90° 140 mm / 45° 110 mm -Miter cut: up to 45° -Sliding table: 355 x 1500 mm -Dimensions total 2275/2010/H1400 mm -Weight: 1058 kg

Condition: new, Year of construction: 2023, Horizontal bending machine AH 40 - ZOPF Dsdpfjqvm Ukox Affekk - with semi-automatic control - hydraulic pressure 40 to. - length of stroke - bending speed adjustable - max. working speed 10 mm/sec. - return speed 20 mm/sec. - hydraulic pressure adjustable - maximum bending high 250 mm - motorcapacity 3,0 KW - 400 V 50 hz 3 ph. - working height 900 mm - closed table - replaceable wear plate - weight 950 kg - bending capacity: flat material max. 150x22 mm round tube up to 60 mm