Extruder

Weber DS120

Year of construction: 1985, condition: good (used), Offer 22556 Technical Data: - Saw blade diameter: 420 mm - Saw blade bore: 30 mm - Max. cutting length: 3000 mm - Smallest cutting length at 90° + 45°: 335 mm - Cutting range, see diagram attached - Swiveling range inwards, manual: 90 - 22.5° - Tilting range inwards, manual: 90 - 45° - Saw blade speed: 2800 rpm - Drive: 380 V / 2 x 4000 Watt - Compressed air connection: 7 bar - Air consumption per working cycle, approx.: 64 l - Space requirement, approx.: W 4500 x H 1950 x D 1600 mm - Weight, approx.: 1400 kg - Including: - Cutting length adjustment with positioning control - Positioning control renewed around 2002 by WOLFF GmbH - Saw head swiveling and tilting for high and wide profiles, Todpfx Aieimdlrs Hob - as well as miter cuts

Year of construction: 2004, condition: reconditioned (used), Stock-No. 2054 Tjdpeiyya Aofx Ai Heb 1used, partly overhauled and functionally tested Single-screw extruder AlphaTec A-ES 75.28 Screw –Ø 75 mm- 28 LD main drive 75 kW- AC Screw speed up to 80 r.p.m. - adjustable 1x venting port with vacuum-pump cylinder barrel heating apporx. 30 kW installed 3x additional temperature controller for down-stream equipment Control board overhauled You´re welcome for inspection visit in our stock Wuppertal-Germany More extruders available

Condition: used, Year of construction: 1951, Technical details: turning diameter over bed: 400 mm turning diameter over support: 240 mm turning length: 1100 mm centre height: im Bett gemessen: 190 mm spindle passage: 40 mm Todpfxju Ix Hds Ai Hsb range of revolution per miute: 37,5 - 950 U/min total power requirement: 3,5 kW tailstock quill taper MT: MK 4 tailstock quill: 180 mm weight of the machine ca.: 1,6 t dimension machine xH: 2,6 x 1,4 x 1,3 m The lathe is equipped with threading device. It is rewired and a new control cabinet is made. Emergency stop switch and chuck protection 3-jaw chuck Ø 250mm rotating tip Tool support quadruple steel holder tool support approx. 30° right/left swiveling 4 Stück Wechselräder Copying device (taper 15° right/left) *

Condition: good (used), Year of construction: 2016, functionality: fully functional, Year: 2016 - technically efficient, ready to work - after full service - cutting length: 4000 mm - discs: 500 mm (feed from the rear) - pneumatic inclination of both heads: 90°, 45°, 22.5°, intermediate angles set manually - operator panel with Windows Tsdpfxjtqmmde Ai Hjb - cooling and lubrication installation for both heads - movable roller feeder - vertical and horizontal pneumatic clamps - automatic disc covers - delivery device for long elements - safety gates

Condition: refurbished (used), Year of construction: 1991, functionality: fully functional, Complete extrusion line for PVC profiles, fully overhauled and tested EXTRUDER: • IDE 75/25 type ME7/3 • single screw, PVC profile geometry and barrel in good condition • screen control (retrofitted by the manufacturer) • year of manufacture: 1993 • 35kW motor, 4 to 40 rpm COEXTRUDER: • IDE MEB 30/25D • Single screw Ø30mm 25LD • PVC profile geometry screw and sleeve in good condition • Year of manufacture: 1992 • 3.8kW motor, 6 to 64 rpm CALIBRATION : • IDE • Length: 2 metres • 2 vacuum pumps, 16 valves • 14 water valves • Manual horizontal and longitudinal adjustments HAUL OFF: • IDE ME30/5 • Year of manufacture: 1993 • Contact length: 1100 mm • Width: 100 mm CIRCULAR SAW • IDE ME52 • Blade: 300 mm • Pneumatic carriage travel 180 mm Tjdsya Eldopfx Ai Hob • Year of manufacture: 1991 TILTING TABLE • IDE • Length: 4000 mm • Pneumatic movement Everything is in very good overall condition, the machines are very clean and ready for use.

Year of construction: 1990, condition: good (used), This haul-off machine, manufactured by Battenfeld Extrusionstechnik GmbH, is in the machine storage of Plastima Used Machinery. The machine, a model Haul-Off R630/6V, dates from the year 1990. Tsdpfsrrv Uwex Ai Hjb Brand: Battenfeld Extrusionstechnik GmbH Model: Haul-Off R630/6V Year of manufacture: 1990 Voltage: 380 V Power: 4,5 kW Pipe diameter max: 110 mm to 630 mm

Year of construction: 1979, operating hours: 216 h, condition: reconditioned (used), functionality: fully functional, Twin-screw extruder, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Year of manufacture: 1979/2022 Machine no.: 85-399 Screw geometry: for PVC-hard profiles Screw diameter: 2 x 85 mm Screw length: 17 x D Screw speed: max. 30 rpm Screw torque: 10000 Nm Tsdpfx Aeyhcc Aoi Hjb Motor power: 3.3 - 25.0 kW Drive motor: commutator motor Elektra Faurndau Cylinder heating/cooling zones: 4/2 (air cooling with fan) Tool heating zones: 8 Temperature control: 12 x digital temperature controllers (PMA KS40) Accessories: Melt pressure sensor and melt temperature sensor Connected load: approx. 60 kW (without tool) Extrusion height: 1100 mm Output capacity: approx. 150 - 180 kg/h for PVC-hard profiles Accessories: Material hopper and connection flange Accessories: Vacuum pump (1.1 kW) incl. material separator Dimensions: 4500 x 1200 x 2100 mm (LxWxH), incl. material hopper Weight: approx. 4000 kg Note: The electrical control cabinet was completely renewed approx. 3 years ago. Since then, the extruder has only been in operation for 216 hours. Condition: The extruder was repainted (light gray, RAL 7035) and checked for function.

Condition: ready for operation (used), Year of construction: 1995, operating hours: 39,000 h, functionality: fully functional, Equipment: documentation/manual, A used and functional profile line for rigid PVC-profiles (300 x 100 mm), consisting of: Twin-screw extruder (parallel) Manufacturer: WEBER Type: DS 7.22 Year of manufacture: 1995 Machine no.: DS70-043 Operating hours: 39,000 hours Screw diameter: 70 mm Effective screw length: 22 x D Screw geometry: for rigid PVC profiles Torque: 4,500 Nm per screw Screw speed: max. 40 rpm, continuously adjustable Drive motor: DC low-voltage motor, thyristor-controlled Drive power: approx. 25 kW Cylinder heating/cooling zones: 5/3 (air cooling with fan) Adapter heating zone: 1 Tool heating zones: 5 Control: conventional control with digital temperature controllers Degassing: Busch rotary vane vacuum pump (1.5 kW) Output capacity, max.: 120-150 kg/h for hard PVC, depending on material Connected load: approx. 50 kW (without tool) Special accessories: Mass temperature sensor and mass pressure sensor Adapter between extruder connection and extrusion tool Used tool set for a window profile (widening), consisting of: - Extrusion tool ‘widening’, incl. heating bands - Dry calibration - Vacuum tank approx. 2 m long, with 8 slots for calibration discs - 16 calibration discs Vacuum calibration unit Manufacturer: Uniplast / Greiner Type: CAL VAK 4P Year of manufacture: 1992 Machine number: K9209590 Total length: 6500 mm Vacuum pumps: 4 x Speck vacuum pumps (4.3 kW each) Water circulation pumps: 2 x Calpeda (1.1 kW each) Caterpillar haul-off, incl. attached saw Manufacturer: Uniplast / Greiner Type: CAT PUL 2D Year of manufacture: 1992 Machine number: R 9204546 Haul-off: Effective contact length: 2000 mm Pad width: 250 mm Haul-off force, max.: approx. 25000 N Speed range: approx. max. 10 m/min. Profile saw: HM circular saw blade: Ø 450 mm Profile cross-section, max.: approx. 300 x 100 mm Tilting table Manufacturer: Ide Tjdpfsyhcabsx Ai Hsb Type: ME N 52/2 Year of manufacture: 1994 Length: 6000 mm Support width: 270 mm Note: The complet profile line was overhauled in 2020 and has only been in operation for 325 hours since then.

Condition: good (used), Year of construction: 1989, operating hours: 24,048 h, Brand: Hans Weber Maschinenfabrik GmbH Type: DS 8.7 Serial number: DS 85 777 Type: Double screw extruder Year of manufacture: 1989 Todpfx Aiszuk Hbo Hsb Operating hours: 24,048 h Screw diameter: 87 mm Connected load: 90 kW