Shredder Weima WLK15 90kW, 1500mm rotor

WEIMA WLK 15 90KW

Condition: used, Year of construction: 2007, SINGLE SHAFT SHREDDER WEIMA MODEL WLK15 MAIN MOTOR 90KW ROTOR KNIVES SIZE 50X50 (NEW KNIVES) Gbsdpfx Ahsyfwz Ionsn ROTOR LENGTH 1500MM ROTOR DIAMETER 370MM THE MACHINE IS 100% FUNCTIONAL READY TO WORK

Year of construction: 1999, condition: ready for operation (used), Working width: 230mm, working height: 160mm, number of spindles: 5, spindle diameter: 50mm, spindle power: 4x 5.5kW/2x 11kW, feed rate: 24m/min, input table length: 3000mm, vertical spindle axial stroke: 80mm, horizontal spindle axial stroke: 45mm. Connected load: 126kW, air requirement: 8400-9600m³/h, machine dimensions X/Y/Z: approx. 3500mm/2000mm/1800mm, weight: approx. 3500kg. Including Weinig EM-11 slide-in unit and suitable distributor for the extraction system. Documentation available. On-site inspection is possible. Gjdpfx Ahju Damdenebn

Condition: used, SINGLE SHAFT SHREDDER WEIMA MODEL WLK15 MAIN MOTOR 90KW ROTOR KNIVES SIZE 50X50 (NEW KNIVES) Gedpfjtqd Ndex Ahnsbn ROTOR LENGTH 1500MM ROTOR DIAMETER 370MM THE MACHINE IS 100% FUNCTIONAL READY TO WORK

Condition: used, Year of construction: 2007, SINGLE SHAFT SHREDDER WEIMA MODEL WLK15 MAIN MOTOR 90KW ROTOR KNIVES SIZE 50X50 (NEW KNIVES) ROTOR LENGTH 1500MM ROTOR DIAMETER 370MM THE MACHINE IS 100% FUNCTIONAL Gbodpfxstqdxfj Ahnen READY TO WORK

Condition: good (used), Year of construction: 2006, machine/vehicle number: 108111, functionality: fully functional, working width: 240 mm, planing height: 160 mm, working height: 180 mm, Four-sided planer after service inspection, machine weight 3900 kg Gbjdpfx Ahsvrq U Donjn

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. Gbsdevf E Avspfx Ahnon We accept no liability for the technical specifications or any errors.

Condition: excellent (used), WEINIG Hydromat H23 Line, S/N 87321, year 1999, Ref-No. 103437 WEINIG Cross Conveyor HighMech E-1, equipped with 6 flat chains approx. 2000 x 3500 mm Hydraulic WEINIG Accelerator Model 814 Short infeed table with heavy-duty 4-roller feed unit Planer/moulder with reinforced KASCHWIG three-sided soundproof enclosure • Max. working width: 230 mm • Max. working height: 160 mm • Electronic feed, frequency-controlled, 8–80 m/min • Feed motor 18.5 kW • 1st spindle bottom 11.0 kW • 2nd spindle right 11.0 kW • 3rd spindle left 11.0 kW • 4th spindle right 11.0 kW • 5th spindle left 11.0 kW • 6th spindle top 15.0 kW • 7th spindle bottom 11.0 kW • 8th spindle top 15.0 kW • 9th spindle bottom 15.0 kW • 10th universal spindle 11.0 kW (four-sided) • Spindle speed 6,000 rpm • Spindle diameter ø 50 mm • All spindle motors equipped with NEW motor start/stop brake units • Pneumatically supported top pressure rollers • Feed rollers D=140 mm • 6 driven rollers in the table • Spindles 1 + 6 + 7 + 8 + 9 with counter bearings • Spindles 8 + 9 with straight jointer • Spindles 8 + 9 with profile jointer • Spindles 6 + 8 with pneumatic pressure • Reduced spacing between feed rollers • Hard-chromed table plates • Hard-chromed fences • Pneumatically supported side pressure rollers • Automatic table lubrication • Centralized lubrication points • Free-standing control panel • Connected load approx. 145 kW / approx. 400 A • Free-standing electrical cabinet • Operating instructions, spare parts list and wiring diagram included • Machine sold without cutterheads Machine dimensions approx.: • Length: 6,000 mm • Width: 2,250 mm • Height: 1,800 mm • Weight: approx. 8,500 kg Factory-new WEINIG components installed: NEW horizontal/vertical spindle NEW counter bearings All spindles with HL bearings All motors newly fitted NEW electronic motor soft start/brake devices NEW hard-chromed table plates NEW hard-chromed fences Many other new parts fitted in the machine Condition: see attached photos – technically in excellent condition Infeed mechanization unrefurbished – complete – fully functional Payment: Net cash before loading Delivery time: By arrangement Delivery: EXW Gbodpowvqklsfx Ahnsn Inspection: Anytime by appointment Errors and prior sale excepted.

Condition: used, Valon Kone VK26M Gsdpjvgtz Nsfx Ahnebn With infeed and outfeed conveyors.

Condition: new, Year of construction: 2008, functionality: fully functional, machine/vehicle number: 2008-176, The Cambio 500 (Söderhamn Eriksson) is a debarker for small logs up to 495 mm (20 inches) in diameter. It operates at feed speeds of up to 120 m/min (393 ft/min). Thanks to its reliability, minimal maintenance requirements, and ultra-low operating costs, the Cambio 500 is the first choice for leading wood processing companies worldwide. Its triangular feed system and carbide-tipped debarking tools, powered by compressed air, are among the key features that ensure superior debarking results. Complete with a feed conveyor. Godpfxsyl Aqho Ahnsbn The machine was not in operation and was in storage.

Condition: excellent (used), functionality: fully functional, Söderhamn small log line with Euromill profiles Debarker Cambio 45 with infeed and guide work after 2D scanner Söderhamn 447 infeed Godpfx Ahewp E E Djnsbn 240-12 chipper canters Block tilt and infeed 240-12 chipper canter Euromill profiles Board separator with adjustable center Chip conveyor under saw line Hydraulic units and electrical cabinet.