Eccentric Press - Single Column

WEINGARTEN ARP100

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Lodpou Rwa Ijfx Akqshn Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Year of construction: 2016, condition: excellent (used), 1 used short bar loader Manufacturer: Breuning Type: ILS RBL 80/12 Year of manufacture: 2016 Lhedpsht Rl Ejfx Akqsn Clamping range: 5-80 mm diameter Length: 100-1200 mm

Condition: good (used), Year of construction: 1988, Press brake, bending machine, swing bending machine, die bending machine -Handover: in its current condition as inspected Lhsdpfjv Tpxqex Akqjn -Function: Manual operation (no automatic operation) -Manufacturer: RAFAMET Swivel bending machine type KM-4 -Drive: mechanical -Max. working width: 2020 mm -Max. sheet thickness: 4 mm -Stop depth: 750 mm -Connected power: kW -Dimensions: 3350/1540/H1510 mm -Weight: 3900 kg

Condition: new, Year of construction: 2024, The Durma HD-TC 60220 pipe laser stands for maximum precision and efficiency in the processing of pipe materials. With its impressive maximum pipe diameter of Ø220 mm and the ability to cut both square profiles of 160 x 160 mm and rectangular profiles of 200 x 100 mm, this pipe laser offers exceptional flexibility for a wide range of applications. Thanks to the advanced automatic loading system, which can handle tubes up to Ø170 mm in diameter, and the ability to process materials up to 6500 mm in length, the HD-TC 60220 is ideal for projects that require fast production with consistently high quality. The minimum material length for automatic loading is 3000 mm, which further increases the efficiency of the machine and reduces processing time. Max. Tube diameter: Ø220 mm Lodpfsq Tpkyox Akqshn Laser power: 3 kW Max. Dimensions of the square profile: 160 x 160 mm Max. Dimensions of the rectangular profile: 200 x 100 mm Min. pipe diameter: 20 mm (12 mm with manual loading) Max. Tube diameter for automatic loading: Ø170 mm Max. Profile dimensions for automatic loading: 150 x 100 mm, 120 x 120 mm Max. Material length: 6500 mm Min. material length for automatic loading: 3000 mm Length of the last piece: 4000 / 6000 mm Unloading length: 150 mm Max. Material weight per meter: 52 kg/m Max. Material weight (total length): 340 kg Max. Loaded weight: 3000 kg Profile types: Round, Square, Rectangular, Elliptical Types of open profiles: L, U

Condition: used, Year of construction: 1996, pressure 80 t throat 320 mm stroke 6 - 118 mm no. of strokes 30 - 80 Hub/min ram adjustment 70 mm table surface area 830 x 610 mm ram surface 650 x 400 mm column daylight (nach hinten) 630 mm total power requirement kW weight of the machine ca. 8,1 t dimensions of the machine ca. B 1,2 x T 1,9 x H 3,3 m Furnishing: - with gear transmission - fixed table Lhjdpfx Ajtycdkekqjn - automatic stroke adjustment - automatic ram adjustment - hydr. Overload - Ejector - Grease central lubrication - Cover plate for drainage hole - Continuous speed control using a frequency converter - Machine is technically checked in our company and receives a new control cabinet with safety controls and touchscreen - current UVV test with braking time measurement

Condition: used, sheet width 250 mm coil outside dia. 1400 mm weight max. in kg 2500 kg plate thickness 2 ... 4 mm straightening feed 2,5 ... 15 m/min coiler: expanding range mm total power requirement 1 + 4 kW weight of the machine ca. 1,8 t dimensions of the machine ca. m decoiler, MHR 250/4: max. coil diameter: 1400 mm coil diameter inside: 450 - 530 mm Lodpsfn Aqmefx Akqohn unbraked decoiler with pressure roller straightening machine, MR 250/4: Belt infeed height: 1250 mm The system was dismantled, checked and repainted.

Condition: new, weight max. 10 t Lhodsf Ep Dispfx Akqen workpiece diameter 100 - 3200 mm drum diameter 300 x 120 mm feed 100 - 1000 mm/min total power requirement 2 x 0,55 kW

Condition: new, Tubend hydraulic profile ring bending machine HPK 50 3 driven rollers Digital display Incl. standard roller set steel Hydraulic / motorized ring bending machine Can be used horizontally and vertically with 3 driven rollers 3 motor-driven rollers Hydraulic infeed of the top roller Hydraulic: 8 tons Rollers are hardened Left/right rotation via foot pedal Mounting: shaft 50 mm Roller Ø 162 mm Speed: 4.5 m/min Motor power: 1.1 kW Lhodpfxjum R U Aj Akqen Electrical connection 400 V According to CE standard Weight 510 kg L.W.H. 810 x 950 x 1500mm Power table see PDF file

Condition: used, Year of construction: 1980, Technical details: pressure: 400 t stroke: 40 - 140 mm strokes / minute continous: 32 throat: 400 mm Lhedpfju N A Uuox Akqen dayligth: min/max: 450/590 mm ram adjustment: 125 mm table-size: 1250x750 mm height over floor: 1130 mm total power requirement: ca. 31,5 kW weight of the machine ca.: 23,0 t machine dimensions LxWxH: 3,7 x 1,7 x 3,9 m dimensions electric cabinet LxWxH: 1,0 x 0,7 x 2,1 m further details: - clamping plate : L x W x H : 1260 x 760 x 100mm - with draw cushion device force 250kN, travel approx. 83mm - control via panel i.D. *

Condition: used, Technical details: plate width: 800 mm coil weight: 12 t sheet width - max.: 800 mm sheet width - min.: 300 mm thickness of strip/band: max. 5,0 mm band speed: 4,5 / 25 m/min work height max.: 1700 mm Payload: 12,0 to (Coil) Weight approx.: 7,3 + 6,62 t dimensions of coil: 3,2 x 1,9 x 2,7 m dimension machine xH: 2,5 x 2,6 x 2,45 m Decoiler with loading device Can optionally be sold together with stock no. 0100571. straightening unit: Infeed rollers: 2 x Ø 144 x 850mm Straightening rolls: 3 x bottom rolls, rigid, Ø 100 x 850mm, 30mm adjustable 3 x top rollers, Ø 110 x 850mm; 30 mm adjustable Coil unwinding machine: Outer Ø 1.500mm Strip width max. 800mm Load capacity max. 12 to Clamping Ø 470 - 630 / 570 - 730mm Transport unit LxWxH: 1700 x 1500 x 1000mm; crosswise running, with prism support 1000 x1000mm Lhjdou Ic Avjpfx Akqon Machine will be offered and sold with Stock no. 0100521 as a decoiling and streightening line. *