Center Lathe

ZMM C 400 TS

Condition: used, Year of construction: 1991, bore capacity in steel (diameter) 50 mm arm length 1100 mm workpiece height max. ca. 1000 mm bore capacity in cast iron 60 mm spindle taper MK 5 spindle turning speed range 28 - 2500 U/min feeds 0,05 - 2 mm/U quill stroke 300 mm distance basic plate - spindle nose 630 - 1380 mm crossrail adjustment vertical 750 mm total power requirement 6 kW weight of the machine ca. 4 t dimensions of machine L x W x H 2,74 x 1,14 x 2,59 mm Ndjdpju Sblwofx Afujb - with thread cutting attachment - Accessories: box table 550 x 550 x 550 mm, vice, coolant

Condition: used, Year of construction: 1983, Bohrleistung in Stahl (-Ø 50 mm throat 1500 mm workpiece height max. 1380 mm Bohrleistung in Guß (-Ø 60 mm Abstand Spindelmitte bis Säule 320 - 1250 mm swival range +/- 180 ° base plate surface area 2640 x 1000 mm max. torque on the spindle 310 Nm Bohrspindel-Ø/ Aufnahme 75 mm /MK 5 bore spindle stroke 310 mm spindle turning speed range 28 - 2500 U/min feed: 0,05 - 2 mm/U power capacity 4 kW Ndsdpfx Ajtv Ikljfueb weight of the machine ca. 4,3 t dimensions of the machine ca. 3,2 x 1 x 2,75 m cube table 500 x 500 x 500 mm

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Ndedpfx Aeuz If Njfueb Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Year of construction: 2013, functionality: fully functional, spindle bore: 105 mm, turning diameter: 800 mm, turning length: 3,000 mm, quill stroke: 240 mm, quill diameter: 100 mm, spindle speed (max.): 720 rpm, spindle speed (min.): 7 rpm, bed width: 600 mm, overall weight: 5,500 kg, rapid traverse X-axis: 4 m/min, rapid traverse Z-axis: 2 m/min, workpiece weight (max.): 2,000 kg, IMTI SDM 800/3000 – USED HEAVY-DUTY LATHE An IMTI SDM 800/3000, manufactured in 2013, from a company liquidation. Originally an exhibition/demonstration machine in our showroom, sold to the previous owner in 2016. Inspection on-site or via video call is possible at any time. KEY FEATURES Nedpfx Afjzi Dhbjuodb - Conventional guide and lead screw heavy-duty lathe, center distance 3,000 mm - Multifix quick-change tool holder with 4 tool holders - 4-jaw faceplate Ø 800 mm, 3-jaw chuck Ø 500 mm - 3-axis digital display SINO SDS6-3V TECHNICAL DATA - Swing over bed: 800 mm - Swing over cross slide: 1,000 mm - Swing over carriage: 480 mm - Center distance: 3,000 mm - Bed width: 600 mm - Spindle bore: 105 mm, spindle nose DIN 55027 size 11 - Spindle taper: Ø 120 mm, taper 1:20 - Spindle speeds: 7-720 rpm - Thread cutting: metric 1-240 mm (52 steps), inch 1-14 (26 steps), module 0.5-120 mm (53 steps) - Longitudinal feed 0.1-24.3 mm/rev, cross feed 0.05-12.5 mm/rev - Rapid traverse longitudinal/cross: 4,000 / 2,000 mm/min - Tool toolbit cross-section: 50 x 50 mm - Cross slide travel: 420 mm, top slide: 200 mm - Tailstock quill Ø 100 mm, taper MK 6, stroke 240 mm - Fixed rest Ø 20-200 mm, traveling rest Ø 20-100 mm - Main motor: 11 kW, rapid traverse motor: 1.1 kW - Workpiece weight between centers: max. 2 t, in chuck: max. 500 kg - Total weight: approx. 5,500 kg STANDARD EQUIPMENT - Multifix quick-change tool holder size D1 with 4 tool holders - 4-jaw faceplate Ø 800 mm, 3-jaw chuck Ø 500 mm incl. chuck flanges 350/500 mm - 3-axis digital display SINO SDS6-3V - Fixed rest Ø 20-200 mm, traveling rest Ø 20-100 mm - Complete coolant system - Fixed center, drive plate, change gears - Electrical end stop longitudinal, halogen machine lamp - German and English technical documentation incl. CE declaration of conformity - 400 V, 50 Hz, 3-phase CONDITION Used machine, manufactured in 2013, from a company liquidation. Sold “as is”, no warranty. Inspection on-site or via video call is highly recommended. OUR SERVICE Online or on-site factory visit, transport organized upon request, assembly, commissioning and operator training by our service technicians, direct German-speaking contact for spare parts and support, member of the FDM, the trade association for wholesale trade in machines and tools. Since this is a single item, subject to prior sale. Please call or write to us, and we will arrange an inspection appointment as soon as possible.

Condition: used, Year of construction: 1987, x-travel 400 mm y-travel 250 mm workpiece height 485 mm Control ELESTA CNC 314 total power requirement 10 kW weight of the machine ca. 4000 kg dimensions of the machine ca. m H A U S E R CNC - Controlled Vertical Precision Coordinate Grinding Machine Model S 3 – CNC 314 Year 1987 / 1998 partially reconditioned by Swiss-HTT # 0463 _____ Table size, approx. 600 x 380 mm Max. load on table, approx. 300 kg Table travel, longitudinal, max. (X Axis) 400 mm Table travel, cross, max. (Y Axis) 250 mm Vertical adjustment of grinding head max. (W Axis) 450 mm Stroke of grinding spindle, max. (Z Axis) 120 mm Table Longitudinal and cross feeds (X/Y-Axis) 0 – 1.500 mm/min Speed of grinding head stroke 15 – 7.500 mm/min Vertical distance between table and grinding spindle, max. 0 – 485 mm Distance between grinding spindle and column 350 mm Conical grinding, up to max. 16 ° Grinding Ø bore approx. 230 mm 18 Spindle speeds, depending on spindle motor 4,500 – 80,000 rpm Nodpot Hw Txofx Afuodb Planetary speeds (C-Axis) 5 – 250 rpm U Axis, radial infeed 6 mm Total electrical load, approx. 10 kW - 380 V - 50 Hz Weight, approx. 4.000 kg Accessories / Special Features: * CNC Continuous Path Control, Model CNC 314, (ELESTA-POLESTA II) with monitor,for 4 axes (XYC+U) in 2 1/2 dimension (XYC) Interpolation with a free programming,the U-Axis is not interpolating it is just an infeed axis. There is also a handwheel controldevice for setting – up purposes. Digital Read-out for the Z-Axis W Axis for vertical positioning of grinding head, Z Axis as high speed stroke axis, also for blind-hole grinding and surface grinding. U Axis for the infeed cycles during bore grinding. C Axis Feed for the of the Planetary Head. * Alltogether 2 grinding turbines 22.500 to 80.000 rpm, with some collets * Built-on Acoustic Grinding Contact Display Device Model KSV 5. * Separate coolant unit with band filter. * Built-on fire extinguishing system. Separate switch and control cabinet. Covered working area. Separate hydraulic unit * Central lubrication, service tools. Condition : Very good - Machine can be inspected under power. Delivery : Ex stock - as inspected under power. Payment : Net, after conclusion of contract

Condition: used, Year of construction: 1990, x-travel 400 mm y-travel 250 mm workpiece height mm Control CNC 314 ELESTA total power requirement 15 kW weight of the machine ca. 5500 kg dimensions of the machine ca. m H A U S E R (Switzerland) CNC - Controlled High Precision Jig Grinding Machine Model S 3 – CNC 314 Year approx.. 1990 S/N 32086 _____ Table size, approx. 600 x 380 mm Max. load on table, approx. 300 kg Table travel, longitudinal, max. (X Axis) 400 mm Table travel, cross, max. (Y Axis) 250 mm Vertical adjustment of grinding head max. (W Axis) 450 mm Stroke of grinding spindle, max. (Z Axis) 120 mm Table Longitudinal and cross feeds (X/Y-Axis) 0 – 1.500 mm/min Speed of grinding head stroke 15 – 12.000 mm/min Vertical distance between table and grinding spindle, max. 0 – 485 mm Distance between grinding spindle and column 350 mm Conical grinding, up to max. 16 ° Grinding Ø bore approx. 230 mm Planetary speeds (C-Axis) 5 – 250 rpm U Axis, radial infeed 6 mm Total electrical load, approx. 15 kW - 400 V - 50 Hz Weight/Total weight approx. 4.000/5.500 kg Accessories / Special Features: • CNC Continuous Path Control, Model CNC 314, (ELESTA-POLESTA II) with new monitor,for 4 axes (XYC+U) in 2 1/2 dimension (XY+C) Interpolation Ndjdpfxst Hxcns Afuob with a free and easy programming for Linear and circle interpolation. Direct Input of data on keyboard, also loading data on RS 232 connection. There is also a handwheel control device for setting – up purposes. Manual feed correction during the working cycle possible. • Digital Read-out for the Z-Axis, Z-Axis as high speed stroke, also good for blind holes. • W Axis for vertical positioning of grinding head slide, • U Axis for the infeed cycles during bore grinding, grinds different bore-Ø automatically. • C Axis Feed for the of the Planetary Head, grinds radii and contours • 2 grinding motors HAUSER approx.. 22.500 to 60.000 rpm, with some collets and arbors • Built-on Acoustic Grinding Contact Display Device Model KSV 5. • Separate coolant unit with band filter. * Built-on fire extinguishing system. • Separate switch cabinet and control unit, Separate hydraulic unit with oilchiller, • Central lubrication, service tools, collets and grinding arbors/tools. Condition : Very good - Machine can be inspected under power commissioned by a Specialist. Delivery : Ex stock - as inspected under power. Payment : Net, after conclusion of contract

Condition: good (used), Year of construction: 1975, Coordinate Grinding Machine Manufacturer: HAUSER Type: 5 SM Year: 1975 with 2-axis digital readout Heidenhain. Table: 750 mm x 620 mm Travel: X 700 mm, Y 500 mm, Z 150 mm Grinding head speeds: 9,000 – 80,000 rpm Total power: 6.3 kW Good condition, in stock. Machine dimensions: 2,500 mm x 1,700 mm x 2,700 mm Weight approx. 5,100 kg. Includes tool cabinet, accessories, and documentation. Nedpfxor H Dvde Afuedb

Condition: good (used), Year of construction: 2004, ELBERON Multipurpose Lathe Type: GRC300X750 Chuck 130 mm In good condition. Nedpfswah Rqsx Afusdb See data sheets for details.

Year of construction: 1964, condition: used, -WKG 429- We are offering a grinding machine from Naxos Union. This is a vertical rotary table surface grinding machine with 2 vertical grinding spindle units. Technical data: Manufacturer: Naxos Union Type: FRDA 600/1000 Year of manufacture: 1964 Rotary table: Ø 1100mm Grinding wheel Ø: Shrink-fit arbor 475/254 Grinding wheel Ø: Plain arbor 457/357 Nedog Nt Dbspfx Afujdb Weight: 8t Grinding method: Segment grinding Segment grinding heads: 2 pcs Accessories: Dressing device Water tank with paper band filter Marposs control

Condition: used, Coil Width: 12″ – 60″ Material Thickness: .015″-.135″ Coil ID: 20″-24″ Speed: 180 fpm Direction: Left to Right Entry Floor Standing Coil Car Mandrel Uncoiler with Powered Expansion Motorized Hold-Down Roll Feed-Up Drive Hydraulic Peeler Nodpfeihf Tpox Afuodb 9-Roll Coil Straightener with 4″ Work Rolls Driven Entry Pinch Rolls 40HP Motor Adjustable Hump Table Mechanical Shear Belt Conveyor with Positive Stop Device Air Gate Sheet Stacker, with Two Section of Gravity Rolls