300/100 TONS HYDRAULIC DEEP DRAWING PRESS

CRONOSSTECH CHSP 300/100

Condition: new, functionality: fully functional, Year of construction: 2025, working width: 6,400 mm, sheet thickness steel (max.): 2 mm, warranty duration: 12 months, working length: 6,400 mm, Immediately available Thalmann TZ 200 / 6.4 m TZ series single folding machine Working length: 6400 mm 6 machine stands Sheet thickness: 2.00 mm at 400 N/mm² Equipment: VFD (vertical force drive) Continuous control shafts Manual crowning (optionally dynamic) 3D graphical control Backgauge 1250 mm Gujdpswlq Nasfx Ad Doi Folding rails 10/10 and 17 mm Motorized backgauge, range 1250 mm with 6 fingers Electric slitter Automatic crowning and radius adjustment Curved folding beam Hardened tools in clamping and folding beam LED bending illumination M-Guard for remote diagnostics directly from the factory

Year of construction: 2020, condition: as good as new (ex-display), Hydraulic press for tests and retouching of dies Brand: MHG Model: ER.2S.DM-300/2100 Serial number: 927 Year: 2020 Required power: 40kw Hydraulic oil: 1000Ltrs. deposit + 200 liters. circuit filling Guedpfxsk Sgvyj Ad Dei Total number of cycles: 403 (NEW MACHINE, PRACTICALLY UNUSED) Maximum force: 300t Number of cylinders: 3 Maximum tooling dimensions: 1400x1400mm Maximum tooling mass: 16,000kg Maximum working table and mobile table opening: 1690mm Minimum opening of work table and mobile table: 960mm Maximum mobile table travel: 730mm Approach speed: 92 mm/s Recoil speed: 93mm/s Stop time: 0.2s Safety distance: 500mm Weight with empty tank: 35.000kg

Condition: used, Year of construction: 1991, pressure 500 t distance between columns 1910 mm stroke 500 mm Distance table/ram, max. stroke up, adjustment up 700 mm table surfache without cutting impact cushions 1910 x 1360 mm table surfache with cutting impact cushions 1600 x 1360 mm table height over floor 800 mm ram surface 1600 x 1270 mm Side window 600 mm speed down 400 mm/s speed up 330 mm/s working speed 10 - 28 mm/s oil volume 1200 l power requirement 60,0 kW weight 40,0 t Dimensions (WxDxH) 3,6 x 2,5 x 5,0 m height over floor 4,5 m permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, cutting impact cushioning, two-hand operation table size depending on cutting impact devices: - without approx. 1910 x 1360 mm - with approx. 1600 x 1360 mm can be offered without putting into operation, with putting into operation in given condition or alternatively with new control Siemens S 7-1500 F Godpevuuiqjfx Ad Dsui

Condition: new, Year of construction: 2025, Metal roof snap lock machine SLP-1 auto with side punching option is the latest project of our company in the direction of equipment for metal roofing production. Snap lock machine SLP-1 auto can produce click-seam panels with fixation holes and punch off side parts of the panels, it makes possible to bend the edge of the panel and join it to the roof elements after. Our machine is equipped with an automation system and make production in a fully automatic mode. This process comes following way: operator of machine put end of metal roll to the pulling rollers of the machine, which moves it to the rolling part of the equipment. At the beginning of the rolling process, two pneumatic punching presses from each side of machine make side cuts of panels. After cutting, the rolling process goes to the next rolling rollers. They gradually form the roofing panel profile and cut out fixation holes with special cutting tool rollers. After rolling, special automatic shear at the end of machine cut off the panel into length with necessary sizes. As machine cuts side parts of panels at the beginning of production process, so it cuts only flat part of panel in the end of production. It makes panel quality better and there are no any deformations as with a profile cutting happens, when guillotine shear has to cut not only flat part but also the lock part of panel. Specifications: Dimensions (mm): rolling machine 3000x1400x900 Guodpfxjuzv Tze Ad Doi guillotine shears 400x1120x1130 Weight (kg): rolling machine 643 guillotine shears: 110 Drive power: rolling machine: 1.5 kW, 220V (or 380V on request) guillotine shears: 1.1kW Maximum thickness of sheet metal (mm): 0.6-0.7mm Workpiece Width (mm): 250-700 Rolling speed (m/min): up to 10 Metal roof panel machine SLP-1 auto has an automation system so help to make minimum part of operator works - he just sets necessary number of panels and their length on the computer to produce, and the machine automatically rolls and cuts them. Therefore reducing the influence of the human factor, manufacturing errors are minimum and panels are all the same sizes and ready for further installation. SLP-1 auto click lock roll forming machine has easy width adjustment system, so to change machine from one panel width to another, the operator just needs to turn the adjustment wheel, so the readjustment takes a very short time for such operation. As additional options metal roof panel roll forming machine SLP-1 auto can have: Cutting knife to cut metal from coil at the end of the metal rolling process to reduce the amount of possible waste material; Ribbed panel rolls, to roll narrow or wide ribs in the center of the roofing snap lock panel; Microwave panel module- device to form small bends along the entire width of the roofing panel, making the appearance of the roof more interesting and eye-catching. Metal unwinder (can be floor-standing, manual console, automatic console).

Condition: used, Year of construction: 2020, functionality: unexamined, total height: 6,400 mm, total width: 4,500 mm, total length: 3,800 mm, operating speed: 110 mm/s, reverse speed: 180 mm/s, distance table to ram: 1,500 mm, We are offering here a new build of the machine shown. The machine was put into operation in 2020 and can be inspected by the customer. Technical data: Press force T 800 Opening force T 80 Motor power KW 55/75 + 55/75 Piston stroke 1000mm Rapid pre-fill speed mm/s 110 Working speed mm/s 6 Return speed mm/s 180 Guide diameter mm 250 Max pressure Bar 250 Useful table area mm 3,500 x 2,000 Gedpfowlrv Ujx Ad Dsui Lower table displacement mm 2000 Between columns mm 2,000 Open height mm 1500 Total front mm 3800 Total side mm 4500 Total height mm 6400 Weight kg 134,600 The MV-800E/NC-SINCRO press was specially developed for the adjustment and testing of molds, dies, and stamps. The 4 columns with 250 mm diameter made of C45E steel were specially manufactured for high stress. It features an optimized hydraulic system with a pressure of up to 250 bar, ensuring long service life and reliability. It meets all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLE • A structure that withstands 600 T concentrated force on 1/3 of its surface. • Lower table with T-slots. • Upper table with T-slots. • Usable table surface: 3,000 x 2,000 mm. CYLINDER AND HYDRAULIC UNIT • Two double-acting hydraulic cylinders with 400 T each. • Single-stage hydraulic unit with automatic shutoff of pre-fill speed and independent operation, equipped with a decompression system and proportional pressure pre-fill valves. Equipped with digital potentiometers on the upper table for displacement control and an electronic synchronization system to compensate for off-center or unbalanced forces. • The press is equipped with a side pressure switch to regulate the most suitable pressure setting for each specific task. • Glycerin manometer with tonnage display. ELECTRICAL INSTALLATION AND SAFETY • Electrical installation for operation with 1 or 2 speeds of the main cylinder feed. • The press has a manual cycle and an automatic cycle (activated via a test button selector): • The manual cycle allows the execution of all movements (step by step) of the press at slow speed. • The automatic cycle allows the press to perform a complete production cycle. • Electrical safety system for the upper table fall protection system. • Lower table with hydraulic removal and physical stops. • The machine features a control panel with a touchscreen display for entering operating and calibration data. • 2 optical barriers of 1,000 mm with safety level IV installed at the front and rear. • Electrical components from Siemens are manufactured according to applicable CE regulations and laws in protection class IP55. • Electrical and hydraulic functions are redundant and self-controlled. Includes an additional safety block and self-monitoring devices for operation and safety. Includes inspection and certification of correct operation and safety distance for light barriers. • Safety is ensured by a laser and area protection with light barriers of level IV.

Condition: used, Year of construction: 2006, pressure 250 t distance between columns 3000 mm stroke 600 mm Distance table/ram, stroke up 900 mm Table surface area 2500 x 1300 mm Table height above floor 1050 mm Side window 1350 mm Ram surface 2500 x 1300 mm Speed down 500 mm/s Speed up 400 mm/s Working speed 36 - 64 mm/s Oil volume 2700 l Power capacity 137,0 kW Weight 54,0 t Dimensions (WxDxH) 4,1 x 4,55 x 6,15 m permitted for manual loading according to the CE Regulations with oil-hydraulic drive, hydraulic cutting impact cushioning, hydraulic ram interlocking No foundation pit necessary Guodpjvuuhaefx Ad Dei can be offered without putting into operation or alternatively with new control Siemens S 7-1500 F

Condition: used, Year of construction: 1993, pressure 100 t distance between columns 1900 mm stroke 500 mm Distance table/ram, stroke up 800 mm table surface area 1850 x 1000 mm Hole in the table 160 mm table height over floor 850 mm ram surface 1850 x 800 mm Side window 540 mm speed down 400 mm/s speed up 400 mm/s working speed 20 - 70 m/min oil volume 900 l Power capacity 34,0 kW Weight 13,0 t Dimensions (WxDxH) 2,7 x 2,2 x 4,0 m permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, hydraulic cutting impact cushioning, hydraulic ram interlocking No foundation pit necessary can be offered without putting into operation, with putting into operation in given condition or alternatively with new control Siemens S 7-1500 F Gsdpfxsvuui Ds Ad Doui

Condition: new, Year of construction: 2025, For customers from: Lithuania, Latvia, Estonia. Equipment for straightening, longitudinal cutting, and shearing rolled metal is an integral attribute of companies working with sheet metal. The FORSTNER company, which has long-term experience in the production of rolled metal processing machines, currently offers the market not only conventional metal shearing machines, but also equipment that performs straightening, longitudinal cutting, and shearing functions. The shearing function is performed using disk or guillotine shears. Depending on your production goals and the tasks the equipment must perform, they can be divided into four groups: 1. shearing machines; 2. longitudinal cutting and shearing machines; 3. straightening and shearing machines; 4. straightening, longitudinal cutting, and shearing machines. The straightening and longitudinal cutting functions of certain models of longitudinal cutting machines can be automated, which allows you to quickly and conveniently change the parameters when starting to work with another material. Forstner EASY series equipment is a machine that cuts a sheet of metal of a set length with the help of a guillotine or circular shears. EASY CUT machines are equipped with circular shears that can cut steel up to 1.0 mm thick. If you need a machine that can cut thicker metal, then it is recommended to choose the EASY PRO model with a guillotine. The working width of the machines can be 1250 mm or 1500 mm. Forstner STRAIGHT. These machines, by pulling a set length of a sheet of metal, straighten it and cut it. Depending on the type of cross-cutting knife and the diameter of the straightening rollers, the thickness of the processed metal varies from 1 mm to 2 mm. STRAIGHT and POWERSTRAIGHT also differ in the adjustment of the straightening rollers: mechanical or automatic. Integrated automatic control saves time in the long term, because changing the operating parameters of the machine is enough to press one button. Automatic control is a great choice when working with many different materials. The Forstner SLIT series is a reliable assistant when cutting rolled metal. The SLIT CUT and SLIT PRO models not only cut the metal, but also cut it lengthwise into strips of the selected width. As standard, these models are equipped with 5 longitudinal cutting knives (the maximum number of knives is 7). The main difference between the SLIT CUT and SLIT PRO models is the type of cutting knife - a circular shear or a guillotine. The Forstner COMPACT series is a device that pulls the required length of material, flattens it, cuts it into strips of the desired width and cuts sheets of a set length. The main difference between the models is the type of knife used for cutting: a circular shear or a guillotine. The flattening rollers and longitudinal cutting knives are mechanically adjusted. Gujdpfxewd E N Es Ad Dei POWER COMPACT is a powerful equipment for flattening, longitudinal cutting and shearing rolled metal. These two models differ in working width and cross-cutting metal thickness. NuSLIT machine models are fully automated equipment. If you are looking for an automatically controlled machine that performs longitudinal cutting and cutting functions, you should choose the nuSLIT PRO or nuSLIT PROCUT models. The difference between these two models is the type of cutting knife: guillotine or segmented disc shears. NuSLIT STRAIGHT PRO and nuSLIT STRAIGHT PROCUT, in addition to the above functions, also smooth the metal sheet.

Condition: used, Year of construction: 1997, pressure 1000 t distance between columns 1260 mm stroke 315 mm no. of strokes 10, 21 - 42 /min distance table/ram, max. stroke up, adjustment up 1295 mm table surface area 1250 x 800 mm table height over floor 670 mm side window 830 mm capacity of ejector in table 63 t ejector stroke of ejector in table 75 mm capacity of ejector in ram 16 t stroke of ejector in ram 23 mm ram surface 1250 x 800 mm ram adjustment 20 mm feeding length transfer 0 - 250 mm closing travel of each rail programmable 0 - 140 mm no. of strokes of the transfer 42 /min power requirement 135,0 kW weight 120,0 t Guodpevuukusfx Ad Dsi Dimensions (WxDxH) 5,9 x 4,8 x 7,95 m height above floor 6,95 m height beneath floor 1,0 m with DC drive, pneumatic clutch, motoric ram adjustment, pneumatic counterbalance in ram, mechanical ejector in table (pneumatically controlled), mechanical ejector in ram, ram interlocking, die clamping system in table and ram, motoric oil circular lubrication, grease lubrication control of the press: Siemens S 5 - CNC 2-Achs-Transfer (Fabrikat Dreher, Type STV-D Modell 350/100-SO, Bj. 2008), Steuerung Siemens S 7 - cleaning system (make Beyss, yom. 1989) as is where is, WITHOUT putting into operation, stored in dismantled condition The press was previously installed in a soundproof enclosure, which is not part of the scope of delivery Video at seller's site before dismantling available

Condition: used, Year of construction: 1992, pressure 300 t Gusdovn U Sropfx Ad Dji passage width 1350 mm stroke 500 mm column travel -side 830 mm table surface area 1350x1380 (1870x1380) mm table height 1060 mm total power requirement 45 kW weight of the machine ca. 20 t dimensions of the machine ca. BxTxH 2500x2000x3950 mm