Injection molding machine

Demag Intelect 150/520 610

Condition: excellent (used), Year of construction: 2007, clamping force: 1,500 kN, screw diameter: 45 mm, displacement volume: 305 cm³, injection pressure: 2,050 bar, injection weight: 270 g, mold height (min.): 275 mm, Demag IntElect 150/520-610 General Information Year of manufacture: 2007 Weight: 6,900 kg Dimensions (L × W × H): 5.5 × 1.5 × 2.1 (2.3) m Control system: NC4 Operating hours: 26,500 h Clamping Unit Clamping system: 150/... Clamping force: 150 t Platen dimensions (H × V): 770 × 770 mm Tie bar clearance (H × V): 520 × 520 mm Mould height (min.–max.): 275 mm (max. increased) Max. distance between platens: 1180 mm Ejector stroke: 125 mm Ejector force: 35 kN Injection Unit Injection unit type: …/610 Screw diameter: 45 mm L/D ratio: 20 Injection volume: 305 cm³ Shot weight: 270 g Kodpfjxxrr Tsx Ab Uedw Specific injection pressure: 2050 bar Wear-resistant screw; bimetallic barrel, standard L:D Three-piece ring-type non-return valve (RSP) Increased injection speed: 300 mm/s Additional Equipment Hour counter reading: 26,500 h - Increased mould mounting height (min. unchanged, max. extended) - Wear-resistant screw; bimetallic barrel; standard L:D; screw diameter 45 mm - Three-piece ring-type non-return valve (RSP) - Electro-hydraulic interface for connecting 2 hydraulic cores on the moving mould plate, via a separate hydraulic unit - Increased injection speed (300 mm/s) - Increased mould mounting height (min. unchanged, max. extended) Offer for the injection moulding machine only

Condition: excellent (used), Year of construction: 1998, Injection moulding machine With two components Kraussmaffei Mutliinject KM200-1000-390 CZ Year 1998 Closing 200 TO Kdodpfx Ajfx Tztsb Uew Scrow 60 mm- 566g Scrow2 - 35 mm - 178 g Tie bars wide 560x560

Year of construction: 2002, condition: ready for operation (used), Clamping force: 2500kN, clear tie bar distance: 630mm/630mm, opening stroke: 1150mm, min. mold installation height: 330mm, screw diameter: 60mm, specific injection pressure: 2000bar, max. stroke volume: 670cm³, connected load: 74kW, control: MC4. Machine dimensions: 5700mm/2200mm/2300mm, machine weight: 12.5t, operating hours: 47,572h. Available from February 2025, including special accessories, Krauss Maffei LRX-S 100, 8x hot runner control points, 4x core pull, blow-out unit, pressure accumulator, hydraulic tie-bar pulling device, energy-saving circuit, ALS interface, 20mA interface and color dosing device interface. On-site inspection is possible, documentation available. Kdsdpeuiykdsfx Ab Ujw

Condition: new, Year of construction: 2024, functionality: fully functional, machine/vehicle number: 61037426, clamping force: 2,500 kN, screw diameter: 60 mm, displacement volume: 792 cm³, injection pressure: 2.42 bar, injection weight: 721 g, mold height (min.): 250 mm, ejector force: 47,000 N, ejector stroke: 200 mm, opening stroke: 1,250 mm, installation height: 700 mm, total length: 8,230 mm, total width: 2,320 mm, total height: 2,210 mm, overall weight: 19,500 kg, heating capacity: 292 kW (397.01 HP), drive type: Vollelektrisch, clear span: 735 mm, tool weight: 3,700,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The all-electric PX series is the answer to your questions about more flexibility with further increases in productivity. Robust mechanics, high-precision and dynamic drive technologies and intelligent energy management make the PX a reliable, productive and efficient performer in any injection molding operation. An ergonomically optimized working height, maximum clearance under the clamp and excellent accessibility ensure maximum user-friendliness. The PX series impresses with its flexibility throughout its entire service life. TECHNICAL DATA: KM 251 / 2000 PX G02 (order 38621992) CONTROL  MC6 with 20.5" TFT color screen and multi-touch function CLAMPING UNIT  Clamping force kN 2500  Mold opening force, max kN 375  Clear width (h x v) mm 735 x 685  Clamping platen (h x v) mm 1000 x 950 Kedpfeuaavzox Ab Uodw  Tool installation height min. - max. mm 250 - 700  Opening width mm 1250  Mold opening stroke max. mm 550  Hydraulic ejector drive  Ejector stroke mm 200  Ejector force forwards/backwards kN 47 / 22.5  Ejector speed forwards/backwards mm/s 350 / 350  Max. Mold weight kg 3700 SPREAD UNIT  Screw diameter / type mm 60 / standard  Effective Ls/D ratio 23.3  Injection pressure bar 2420  Stroke volume cm³ 792  Shot weight at max. stroke for PS g 721  Injection speed mm/s 125  Injection flow rate cm³/s 353  Screw drive/speed 1/min 327  Plasticizing flow rate g/s 82.8  Nozzle contact force kN 57 ELECTRICAL PARAMETERS  Connected load kW 63.5  Installed heating capacity kW 29.2  Power supply V / Hz 400 / 50 WEIGHT AND DIMENSIONS  Net weight with switch cabinet t 19.50  Length x width x height m 8.23 x 2.32 x 2.21 ADDITIONAL EQUIPMENT  Enlarged mold opening width  Low-wear plasticizing (ZE23.03)  Hydraulic core pull 2+2-fold  Core pull pneumatic 1+1 - fold  Air valves 1+1-fold  Pneumatic cascade 4-fold  Euromap interfaces E18, E67, E77  Water battery 4 - compartment  Hot runner control points 12 - compartment  Adaptive Process Control (APC) The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your inquiry.

Condition: excellent (used), Year of construction: 2006, operating hours: 45,200 h, 1,0 St. gebr. Spritzgießmaschine mit Roboter Hersteller: KRAUSS MAFFEI Typ: KM200-700C2 Baujahr: 2006 Schließkraft: 200 Tonnen Holmabstand 560 x 560 mm Schnecken DN: 45 mm Max. Hubvolumen: 305 cm³ Spritzteilgewicht: 278 g/PS Steuerung: MC5 Ausstattung: Roboter GHS Baujahr: 2004 Kedjxpnpispfx Ab Usdw Verschleißarme Plastifizierung 1 St. Kernzug 1 St. Förderband Sicherheitszaun Ca. 45.300 Betriebsstunden

Condition: excellent (used), Year of construction: 2010, 1,0 St. gebr. Spritzgießmaschine mit Roboter Hersteller: KRAUSS MAFFEI Typ: CX250-1000 Baujahr: 2010 Schließkraft 300 Tonnen Holmabsta 630 x 630 mm Einbauhöhe min.: 330 mm Öffnungsweg: 820 mm Schnecken DN: 50 mm Max. Hubvolumen: 432 cm³ Spritzteilgewicht: 393 g/PS Steuerung: MC5 Ausstattung: Roboter, Krauss Maffei, Typ: LRX100S 2 St. Kernzüge an BWAP Kdjdpowcb Nrsfx Ab Uow Hochverschleißfeste Spritzeinheit

Condition: ready for operation (used), Year of construction: 2012, General Data Measurements width 1900 mm Measurements depth 6600 mm Measurements height 2400 mm Machine weight 14900 kg Kedpfsxnd Sqex Ab Uedw Injection Unit Screw diameter 50 mm Shot weight 482 g Stroke volume 530 cm3 Injection pressure 2426 bar Adjustable heating zones 5 Nozzle pressure 110 kN Clamping Unit Clamping force 2500 kN Opening stroke 670 mm Max open daylight 1380 mm Mould height min 330 mm Mould height max 710 mm Ejector stroke 200 mm Ejector force for / back 81 kN Media Pump drive power 30 kW Oil tank 550 L This SUMITOMO SHI DEMAG El-Exis S250/630-1600 was manufactured in 2012. It features a clamping force of 2500 kN, a screw diameter of 50 mm, and a shot weight maximum of 482 g. The machine has a dry cycle time of 1.2 seconds and a total installed power of 57.9 kW. If you are looking to get high-quality injection moulding capabilities, consider the SUMITOMO SHI DEMAG El-Exis S250/630-1600 machine we have for sale. Contact us for more information. Application Types Injection Moulding

Year of construction: 2016, condition: ready for operation (used), Clamping force: 2500kN, injection unit: 1400CX, pump motor power: 45kW, plasticising system: HPS-UN, screw diameter: 60mm, injection volume: 820cm³, plasticising stroke: 82.4mm, tie bar spacing: 530mm. Machine dimensions X/Y/Z: approx. 6500mm/2100mm/2300mm, weight: approx. 15000kg, control: MC6, pump hours: 42115h, automatic hours: 39148h. Includes conveyor belt MK GUF-P 2000 AF. Documentation available. An on-site inspection is possible. Expected to be available from December 2025. Ksdpfxjw Exrpe Ab Uedw

Condition: good (used), Year of construction: 2000, operating hours: 77,000 h, functionality: fully functional, clamping force: 2,000 kN, screw diameter: 50 mm, Type: KM 200-700 C2 (CLEAN ROOM) Year: 2000 Screw ø: 50 mm Operating hours: 77,000 h Kdodpfewm Ifnjx Ab Usw With accumulator Euromap 12 Injection pressure: 1,892 bar Island distance: 560 x 560 mm Molding table size: 915 x 915 mm Min tool: 350 mm Opening path: 700 mm Daylight: 1,050 mm

Year of construction: 2005, condition: ready for operation (used), This SUMITOMO SHI DEMAG El-Exis S 250/630-1450 was manufactured in 2005. It features a central accumulator for high-speed injection and chromed tie bars. The pump drive power is 22.0 kW, with a mains voltage of 400 V/50 Hz. It includes a color data display with VGA interface, an oil cooler, and electric screw drive. Consider the opportunity to buy this SUMITOMO SHI DEMAG El-Exis S 250/630-1450 hydraulic injection moulding machine. Contact us for more information. Application Types Injection Moulding Kodpfoxmbv Djx Ab Usdw