Servo press

Durendus Einständerpresse

Condition: new, Year of construction: 2026, pressing force: 100 t, pressure:100 t passage width:500 mm stroke:400 mm Approx. weight (w/o operational materials):5,5 t Measurements L x W x H:ca. 1300 x 2000 x 2750 mm Table size:750 x 600 mit T-Nuten mm Table height above ground level:850 mm Oil Tank Capacity:190 l main cylinder:230 Ø mm Auxiliary cylinder:2 Stk - 50 x 30 Ø mm Auxiliary guidance:2 Stk - 50 Ø stk. Engine Output:11 kW :23 Lt./min. Hfedpfefu Nqxox Adajf Approach Speed:110 mm/sec Pressure Speed:9 mm/sec Return Speed:200 mm/sec Ram plate:750 x 600 mit T-Nuten mm pre-run valve:NG.63 Stk Painting:Lichtgrau & Dunkelgrau Siemens Control System:S7 1200 Monitor:Siemens 7 Zoll Light sensors sick:750 + 150 mm Control Set-up operation:manuell ohne Lichtsensor Automatic control:mit Lichtsensor Special feature: When operating at 260bar the machine reaches a pressure level of 70 tons.

Condition: used, Year of construction: 1983, Technical details: Pressure: 160 t throat: 360 mm max. ram stroke: 500 mm distance table/ram: 800 mm clamping plate on table: 1250x630x100 mm passage opening in table: 4x Ø 62mm mm Hfsdsu Nfvuopfx Adajf ram speed - forward: 200 mm/s ram speed - reverse: 125 mm/S ram surface area: 450 x 850 mm mortise hole in ram: Ø 49 mm height over floor: 810 mm total power requirement: 17 kW weight of the machine ca.: 7200 kg dimension machine xH: 2,1 x 1,4 x 3,4 m manual counter *

Condition: used, Year of construction: 2017, pipe diameter (max.): 80 mm, mandrel length: 4,500 mm, Mandrel bending machine S8004 ----- For the production of dimensionally accurate pipe geometries with bending radii of up to 1.5XD → maximum bending performance pipe 76 x 4 mm (400 N/mm²) → maximum bending performance pipe 60 x 60 x 3 mm (400 N/mm²) → maximum bending performance pipe 76 x 2.9 mm (stainless steel) → total connected load 7 kW → pipe length 4.5 mtr Robust and durable steel construction in a force-locking connection - no construction susceptible to torsion due to, for example, the split construction of the bending head and mandrel carrier. Maintenance-free electromechanical drive of the bending axis. The touch display of the control enables simple and intuitive programming and use of the system. After the pipe has been pushed on, it is fixed in the carriage by the chuck. This enables the pipe to be positioned precisely and thus the creation of dimensionally accurate geometries. The standard also includes checking the pipe geometry before the bending process: If the bending process is started in the wrong position, the machine does not give permission for this. This prevents incorrect operation. Optional additional features provide more convenience and increase the output and thus the efficiency of the system. Data is exchanged from the optional pipe calculation program TBS-3D (PC version) via USB stick or via FTP access from the computer to the machine control system. USB or LAN connectors (RJ45) are available as standard. Existing pipe geometries can be converted quickly and easily, for example, using the STEP format. Standard equipment: → Electromechanical drive of the bending axis 4 kW → Speed 2.9 rpm (=17°/sec.) → Bending direction left → Bending angle resolution 0.1° → Max. bending radius 200 mm → Bending shaft diameter 50 mm → Electronic length measurement ±0.1mm → Electronic twist measurement ±0.1° → Manual stop system (overtravel stops in length) → Manual locking system (15° in twist) → Three-jaw chuck for locking the pipe in the carriage → External control panel PLC control: → Touchscreen 10.1" → ETH 10/100, X2X Link, USB → Foot switch operation → Data transfer via network (W)LAN or USB → Material database Unique graphic programming: Simple geometries can be calculated directly on the machine. The control calculates the feed values directly after entering the length and angle and the bending angles. Hydraulics: → Hydraulic power 3 kW → Hydraulic pipe clamping with adjustable clamping pressure → Programmable early mandrel retraction Options (can be ordered as additional equipment): Hsdpettah Rofx Adaoff → Variable bending speed using frequency converters or servo motors → Automatic tool retraction (manual or controlled) → Pneumatic chuck → Automatic mandrel lubrication → Pneumatic stop system (length + twist) → Mobile version (rollers) → Radius extension Pictures show new machine

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: NC control, degree of automation: semi-automatic, actuation type: hydraulic, controller manufacturer: MG, controller model: 4-AXIS, number of rollers: 4, roller (bottom) diameter: 245 mm, roller (top) diameter: 265 mm, side roll diameter: 185 mm, roller diameter: 280 mm, roller length: 2,550 mm, working width: 2,500 mm, working height: 700 mm, sheet thickness (max.): 14 mm, sheet thickness steel (max.): 12 mm, sheet thickness stainless steel (max.): 10 mm, overall weight: 7,500 kg, total length: 4,200 mm, total width: 1,500 mm, total height: 1,600 mm, power: 18 kW (24.47 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 3, Equipment: centralized greasing system, cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, 4roll plate bending machine 2500 X 12 mm with central support hydraulic for large diameters and side arm plate support Capacity plate width 2500 mm Plate thickness 12 mm Prebend 10 mm Upper roll 265 mm Lower rolls 245 mm Surface useful on rolls 2550 mm Power supply 380/50 Electric motor 15 Kw on hydraulic unit Configuration Hardened rolls very high surface resistance Conical bending attachment Digital position readout of the rollers Safety and emergency installed per norms Hydraulic rolls power driven with planetary gear unit Hydraulic motion of rollers individual with dual initial pre-pinch Open front drop-end hydraulic to unload the closed shells Central support vertical hydraulic operated for large diameters Side arm operated hydraulic support Total weight of the machine 7500 Kg machine layout 4200X1500 X H1600 mm Hsdpfexw S Eqex Adajff

Condition: excellent (used), Year of construction: 2012, Technical Data: Working width: 2600 mm Bending capacity: 20.0 mm Pre-bending: 16.0 mm Top roll diameter: 330 mm Middle roll diameter: 300 mm Side rolls diameter: 240 mm Conical bending device via tilting of both side rolls Mobile control panel with digital display Motor power: 11 kW Hfjdpfx Adsx Ii Hvoasf CE mark Dimensions (L x W x H): approx. 5800 x 2300 x 1900 mm Weight: approx. 11 t Additional equipment: Upper bending aid The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: used, Year of construction: 1996, Hydraulic mandrel bending machine with many accessories Preselection of 8 different bending angles with digital display Digital length display and digital display of twist Hfsdpeq Daxtsfx Adajf Max. usable length: 6096 mm Round steel tube (S 235): 60.0 x 6.0 mm Round tube stainless steel (S 355): 60.0 x 4.0 mm Square steel tube: 50 x 50 x 4.0 mm Rectangular steel tube: 60 x 40 x 2.0 mm Max. bending angle: 180° Weight: approx. 1800 kg

Condition: as good as new (ex-display), Year of construction: 2025, Max Ø 114mm; Straight and bent round tubes; One grinding station; Grinding of straight and bent round tubes up to Ø114mm with maximum flexibility. The ML100 tube grinding machine is the perfect choice for surface grinding and polishing of round, oval and elliptical tubes. The ML planetary belt system allows belt grinding without rotating the tube to deliver the best results. The feed system safely feeds the straight tubes into the grinding station for a consistent and productive surface finish. ML100 Hjdpfxjtzkgbs Adaoff Working capacity (Ø mm) 3 - 114 No. of stations 1 Sanding belt, dimensions (mm) (2x) 50x940 Sanding belt speed (m/s) 3-22 Feed speed (m/s) 1-5 Sanding belts Motor (kW) 3 Wheel, motor (kW) 1.5 Feed motor (kW) (2x) 0.12 Total power (kW) 5 Power consumption (A) 11 Dust extraction connection (Ø mm) 80 Dimensions (mm) 750x1000x1300 Weight (kg) 250

Condition: ready for operation (used), Year of construction: 2023, OEM – laser marker (laser class 4) Laser source is a 20 Watt fiberlaser with 1064 nm wavelength. The working area is 100 x 100 mm, up to 300 x 300 mm is available as an option. No external cooling is necessary. Input-voltage: 110...240 VAC / 50 Hz. Further applications are laser engraving and material ablation. The control software is installed on a PC, optionally also a Laptop can be used. The language of the software can be choosen (German, English). Hfjdpfx Asn Atmvsdasf The laser is prepared for an integration into a ‘higher level system’. For this interfaces for Interlock, emergency stop, laser control etc. are available. We are happy to support the customer according to his requirements.

Condition: used, Year of construction: 1992, machine/vehicle number: 150258, Offer 24348 Technical data: - Infinitely variable pressure capacity 15 t - Infinitely variable stroke 150 mm - Mandrel bending device up to 6000 mm - Mandrel bending angle 180 ° - Drive 400 V / 4 kW - Space requirement approx. W 1500 x H 1200 x D 1100 / 7500 mm - Weight approx. 1500 kg - Bending capacity - Bending capacity horizontal bending flat bars 120 x 10 mm - Tube bending ( pressing process ) up to approx. 11/2 " - Mandrel bending up to 42 mm Hsdpfx Aout Uiqodasff - Bending tools - Tube bending tools Horizontal bending - Mandrel bending tools steel approx. 21.3 R 50 ; 26.9 R 57 ; 30 R 67 ; - 33.7 R 72.5 ; 42.4 R 92.5 ; mm - Mandrel bending tools plastic approx. 10 R 60 ; 12 R 65 + 85 ; 17.2 R 100 - 28 R 65 ; 33.7 R 120 ; 36 R 100

Condition: new, Year of construction: 2025, functionality: fully functional, The universal laser marking system LAS 28 XLe from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes integrated PC with Windows operating system and laser software. Optionally, the laser model LAS 28 XLe can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extension arms for marking long parts, movable Z-axis, drawer systems, etc., can be realized. Made in Germany Fiber laser 30 Watt, 20 Watt or 50 Watt - Laser class 1 - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) Hjdpfsrxrrhjx Adasff - Signal light for displaying operating status - optional: rotary axis (3-jaw chuck) - optional: extraction system (incl. activated carbon filter) - optional: digital height measuring system - optional: autofocus - EZCAD marking software in German / English (other software available on request) - Pilot laser (simple preview, plain text preview) - Focus finder (simple focus adjustment) - max. component height approx. 300mm - Electrically adjustable Z-axis - Integrated PC with Windows operating system - Height-adjustable screen and keyboard support - Frame made of aluminum profile - Air-cooled - Door width approx. 700mm / door height (pass-through): approx. 400mm - 230V connection - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) with screen holder approx. 1500 x 800 x 1900mm (LxWxH) - Weight: approx. 120 kg