Strip leveller 1.900 x 10 mm

MC KEY

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, sheet thickness (max.): 60 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), Equipment: cone bending device, documentation/manual, 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Dwodszbqqujpfx Ab Noc Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls 570 / 500 / 430 mm Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1999, functionality: fully functional, turning length: 3,000 mm, turning diameter: 1,000 mm, spindle bore: 197 mm, Upon request, videos of the machine in operation can also be provided. Djdpfx Aoyr N N Rob Njwc Maximum turning length: 6000 mm Turning diameter: over cross slide: 1000 mm over bed: 1250 mm Spindle bore: 197 mm Spindle speeds: 0 – 665 rpm Faceplate diameter: 1200 mm Workpiece weight: 15000 kg between centers Motor power: 55 kW / 74 hp 3 gear stages: 1.5-55 / 50-180 / 180-665 rpm Accessories: Sauter 4-position tool turret (rotation defective) Tailstock (hydraulics partially defective, pressure loss) Chip conveyor 2 chip guard doors (incl. safety device) 4-way bed machine (flat bed) LED lighting

Condition: excellent (used), travel distance X-axis: 1,500 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 750 mm, table width: 1,500 mm, table length: 850 mm, rotational speed (max.): 2,500 rpm, quill stroke: 120 mm, SHW UF 5 Travels - X-axis (rotary table): 1,500 mm - Y-axis (vertical headstock): 1,000 mm - Z-axis (horizontal headstock): 750 mm Control system - CNC control: Heidenhain TNC 355 Automatic swivel head (change between horizontal and vertical machining) Quill 120mm Dsdpfjvfm I Tsx Ab Nswc Milling spindle holder SK 50 Speed 2500 rpm Partial overhaul 2014 - Year of construction 1990 - Inspection/repair 2025 Table assembly - Travel distance: X = 1,500 mm - Clamping surface: 1,500 x 800 mm Chip conveyor Splash guard cabin We have ALL spare parts for this series (SHW UF 5) in stock! About us: MBM Maschinenservice & Gebrauchtmaschinen GmbH is an independent specialist for SHW machine tools. Our main focus is in the field of tool milling machines. Our services include spare parts deliveries, on-site customer service, machine overhauls and control system modernizations. Services: - Used machines - Spare parts - Customer service - Machine service - Machine overhauls - Control modernization _____ Used machine - used milling machine - used bed type milling machine - orthogonal milling head - metalworking - tool milling machine - milling head - SHW machine - SHW spare parts - milling machine used - milling machine used - CNC milling machine used - drilling milling machine used - milling machine metal used - metal milling machine used - metal milling machine used metal milling machine used - used cnc milling machine - cnc milling machines - cnc milling machines - milling machine - large part machining - large part machining - large part machining - cnc large part machining - milling - shw - uf5 - uf 5 - Uniforce - SHW UF - SHW Uniforce - SHW Uniforce 5 - UFZ 5 - UFZ5L - UFZ 5 L - MBM Milling Machine - MBM Machine

Condition: used, 72″ x .187″ x 50,000Lb Paxson Loop Slitting Line Make: Paxson Dedpfx Absihf Ufj Nowc Material Width: 12″ – 72″ (Uncoiler 60″) Material Width: .010″ – .187″ Coil Weight: 50,000Lb Coil ID: 20″ – 24″ Coil OD: 72″ Speed: 500 /1000 fpm Direction: Right to Left Material Strength: 40,000 yield / 50,000 psi shear Material: CR, HR, Galvanized Entry Transfer Cart Entry Coil Car Mandrel Uncoiler Powered Hold-Down Roll Powered Expansion Sliding Base Hydraulic Peeling Table Driven Pinch Rolls

Condition: excellent (used), Year of construction: 1984, functionality: fully functional, turning diameter over cross slide: 630 mm, spindle bore: 320 mm, turning diameter: 1,200 mm, turning diameter over bed slide: 930 mm, turning length: 3,000 mm, Lathe in very good technical condition, has seen very little use and was not used for machining pipes. The Poręba TPL 90/3m lathe (also listed in market nomenclature as a variant of the TPK 90 series) is a textbook example of an Oil Country Lathe / Hollow Spindle Lathe. This model fulfills all the specific criteria for machines intended for the Oil & Gas sector: • Massive spindle bore (Big Bore): This version features a spindle bore with a diameter of 320 mm (approx. 12.5 inches), allowing for easy insertion of thick-walled drill and casing pipes. • Dual chucking system: The headstock is designed for mounting two independent lathe chucks (front and rear, typically 28 inches in diameter), ensuring the pipe is clamped and stabilized at both ends of the spindle. • Optimal working dimensions: The 3m designation defines a turning length between centers of 3000 mm, which, combined with a swing over bed of 930 mm (hence the "90" in the name), allows for machining heavy-duty pipeline components. • Exceptional rigidity: FUM POREBA factory machines are renowned for their monolithic, very wide and heavy cast iron beds, which effectively dampen the immense vibrations generated during taper thread cutting. In international used machinery catalogues, this specific Poręba model is directly classified under the Oil Field Lathes category. TECHNICAL SPECIFICATIONS: Dwjdpfxjy Sf Azs Ab Njc Geometric parameters and machining ranges • Swing over bed: 930 mm / 36.6 in • Swing over cross slide: 630 mm / 24.8 in • Swing in gap: 1200 mm / 47.2 in • Maximum turning length between centers: 3000 mm / 120 in • Bed width: 585 mm / 23.0 in Headstock • Spindle bore diameter (Hollow Spindle): 320 mm / 12.6 in (in US nomenclature classified as a 12.5" version) • Spindle speed range: 5 – 250 rpm, or modified versions up to 710 rpm • Number of spindle speed steps: 18 Feed and thread cutting system • Longitudinal feed range: 0.1 – 12.8 mm/rev / 0.004 – 0.504 in/rev • Cross feed range: 0.05 – 6.4 mm/rev / 0.002 – 0.252 in/rev • Types of threads cut: Metric, Inch (Whitworth), Module, Diametral Pitch (DP) Tailstock • Tailstock quill diameter: 130 mm / 5.1 in • Tailstock quill travel: 300 mm / 11.8 in • Internal taper of quill: Morse No. 6 (MT6) Drive and dimensions • Main motor power: 22 kW / 29.5 HP • Overall length: approx. 5500 mm / 216.5 in • Overall width: approx. 1750 mm / 68.9 in • Overall height: approx. 1500 mm / 59.0 in • Total weight: approx. 8000 kg / 17,630 lbs

Condition: used, Year of construction: 2006, functionality: fully functional, machine/vehicle number: 06007153/001, total height: 6,050 mm, total width: 3,380 mm, total length: 3,074 mm, load capacity per storage section: 210 kg, construction height: 6,050 mm, input voltage: 400 V, Automated Warehouse Optimization Storage System KARDEX Shuttle XP500 System Type: SHUTTLE-XP-500-3050x864 Control: C2000, with B/W OP2000 display Serial Number: 06007153/001 Year of manufacture: 2006 Total load capacity: 2 x 33,550 kg Load per tray: Medium: 205 kg (evenly distributed) Tray dimensions: 3050 x 864 mm Number of trays: 36 units (more or heavier trays available upon request) Shuttle dimensions (W x D x H): 3380 x 3074 x 6050 mm (Height adjustable to available space) Power supply: 3/N/PE400 V, 11 A, 50/60 Hz, 4.9 kVA This offer is valid as long as the system is unsold Technical details per Shuttle: - Maximum total capacity of the KARDEX Shuttle XP: 2 x 33,500 kg - Maximum tray capacity: 36 trays, Medium: 210 kg each, evenly distributed; more or heavier trays can be ordered. - Tray dimensions: 3050 x 864 mm - Machine dimensions (W x D x H): 3380 x 3074 x 6050 mm - System footprint approx.: 10.39 m² - Storage capacity with 36 trays: approx. 95 m², each tray approx. 2.64 m² - Electronic volume measuring system with 25 mm grid on the display - Access opening with sliding doors for protection of personnel and stored goods - C2000 Control System, with B/W OP2000 display - LED anti-glare lighting above access point - Toothed-belt drive for minimal noise - Toothed-belt drive for fastest order picking - Shelf spacing adjustable in 25 mm increments by configuring support profiles, ideal for high-density storage - Weight management system monitors the load per tray - Includes light pointer Price: On request only by e-mail Dedpexq Tbtjfx Ab Newc Price: excluding VAT, including transport and installation Delivery time: from stock Machinehandel De Leeuw BV specializes in used paternoster systems from brands such as Kardex, Hanel / Haenel, Electrolux, Bertello, Megamat, Lista, Denocard, and automated storage systems such as the Kardex Shuttle XP and XPlus systems. Machinehandel De Leeuw BV Oordeelsestraat 7-B 5111 PA Baarle-Nassau The Netherlands

Condition: used, Year of construction: 2014, total length: 1,500 mm, total width: 1,150 mm, total height: 2,400 mm, Weight: 3.600 kg - Year: 2014 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 441 - Power [kW]: 3.0 - Press force [ton]: 28 - Max. working width [mm]: 1000 - Column gap [mm]: 950 - Throat depth [mm]: 220 - Backgauge depth [mm]: 415 - Transport dimensions: 1500mm x 1150mm x 2400mm (l x w x h) - Transport weight [kg]: 3600kg - Transport packages [pcs.]: 1 Financial information Dwsdpfexapftjx Ab Nec VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2001, functionality: fully functional, Press force 85 t, Bending length 2050 mm, Distance between uprights 1750 mm, Control DELEM, Stroke 215 mm, Throat depth 410 mm, Total power 13 kW, Weight 8,750 kg, Machine dimensions 3190 x 2100 x 2375 mm Dsdpfxew Imq Rj Ab Nswc

Condition: good (used), Year of construction: 1998, Press Force 315.00 t Stroke 500 mm Throat 425 mm Djdpfx Ajv Rwu Ujb Nowc Installation Height (Upward Stroke) 1,000 mm Table Surface 1,200 x 815 mm Table Height above Floor 800 mm Ram Surface 1,100 x 700 mm Speed Down 48 mm/s Speed Up 330 mm/s Working Speed 19 mm/s Oil Volume 1,600 l Power Requirement 82.0 kW Weight 23.00 t Dimensions (WxDxH) 2.4 x 2.8 x 4.0 m For Permitted for manual loading according to the CE standard with oil-hydraulic drive, controllable depending on pressure/time and travel, light-guard at the front (Sick), two-hand operation permitted for manual loading according to the CE standard with oil-hydraulic drive, controllable depending on pressure/time and travel, light-guard at the front (Sick), two-hand operation

Condition: used, Year of construction: 2004, Technical details: x-travel: 1500 mm y-travel: 1000 mm z-travel: 1000 mm control for program: TNC 530 spindle hours: noch nicht bekannt h milling head speed: 1: 30 bis 930 und 2: 930 bis 4000 / steples U/min tool taper: horiz./vertical: SK 50 (DIN 69871/Din 69872 Form A) Dedpeu Nc Risfx Ab Nswc max. torque on the spindle: 1000 Nm spindle head swivable left - right: 90 ° feed: 1 - 6000 mm/min feed power: 30 kN kN rapid traverse: 15 m/min Number of tools: 1 St. table clamping surface LxW: 1600 x 800 mm table load: 40 kN kN voltage: 400 V / 50 HZ V total power requirement: 42 kW Weight approx.: 15,2 t compressed air: 6,3 bar dimension machine xH: 3,1 x 4,7 x 2,6 m dimensions: Kühlfilter: 1,9 x 1,6 x 1,4 mm space requirements approx. LxWxH: ca. 38,5 m² m² Applications: Milling, drilling; tapping, boring. with direct coded length measuring systems the guideways of the 3 axes are on flat guideways CTS and external cooling Milling head position controlled +/-90° milling spindle nominal drive power 22 kW with integrated hydraulic power unit up to 100bar operating pressure with coolant unit with filtration, with high pressure pump 60 bar (internal cooling), nominal delivery 20 l/min. and low pressure pump 4 bar (external cooling) as well as spray gun Hinged belt chip conveyor DGS, type SSF 600 P50 Accessories: Measuring probe SK40 Reference tool SK40 Milling head SEMPUCO *