Used Eht Tss 20-25 for sale (54)

Condition: used, Year of construction: 1994, sheet width / mm plate thickness / mm distance between columns / mm Lasdpfeuddh Aox Agzek Manufacturer: EHT Type: TSS 20-25 Year of construction: 1994 Max. Cutting length: 2250 mm Max. Sheet thickness: 20 mm Strip width min / max: 10/1000 mm Distance between the consoles: 2530 Height above the ground: 900 mm Table length without extension arms: 3030 mm Oil volume: 800 l Max. Pressure: 280 bar Operating voltage: 400V Control voltage: 230 V. Nominal current: 87 A. Weight: 15.8 to Dimensions L x W x H: 3500 x 2500 x 2400 mm Accessories / special equipment Pneumatic cutting gap adjustment Cutting length limitation Roller conveyor elevation bracket Hand protection 1 bay Multitron control Multitron PS 80; ELCO 85 P Lower knife height adjustment

Condition: good (used), Year of construction: 1987, fabric-no. 202 395 working length 2550 mm output 2000 KN Lsdoq Awh Repfx Agzeak tracking travel 13 mm safety distance 176 mm

Condition: used, Year of construction: 1971, sheet width 2000 mm plate thickness 16 bei St 42 mm Lodpfx Asww Nccogzeak passage width 2250 mm impact length 1000 mm blade length 2005 mm throat 600 mm cutting gap adjustment 0,05 - 0,95 mm cutting angle 1° 40' ° down holder 10 Stück back stop - adjustable 10 - 1000 mm table: 2500 x 700 table height over floor 800 mm quantity of oil 900 l weight of the machine ca. 10 t dimensions of the machine ca. 3 x 2,3 x 2,3 m voltage 380 V Food switch, material support beams, spare knifes.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2003, controller model: CYBELEC DNC 1200 PS Eco, bending force (max.): 225 t, stroke length: 550 mm, distance between stands: 1,550 mm, working length: 2,050 mm, TECHNICAL DETAILS Press force: 225 t Bending length: 2,050 mm Upright distance: 1,550 mm Stroke: 550 mm Lsdpsxxqm Nsfx Agzeak Table height: 700 mm Throat depth: 405 mm Distance table/ram: 320-870 mm Frame throat: 405 mm MACHINE DETAILS Control: CYBELEC DNC 1200 PS Eco Machine weight: approx. 14,000 kg EQUIPMENT Controlled axes: Y1 - Y2 - X - R Z1 and Z2 manually adjustable Lasersafe angle measurement Pneumatically adjustable support table Pneumatic upper and lower tool clamping 2-hand-foot control Manual crowning

Condition: used, functionality: fully functional, Year of construction: 1987, machine/vehicle number: 101536, Offered for sale is a hydraulic guillotine shear Manufacturer: Eisen und Hammerschmidt GmbH Model: TSS4-20 Year of manufacture: 1987 Lsdpfxjx Da D Ue Agzjak Serial No.: 101536 Capacity: 4 mm Working width: 2,000 mm Control: ELGO Type P8511 Light curtain system by SICK Used, fully functional condition. Collection by purchaser; assistance with dismantling/transport can be arranged if required. — If you are interested or have any questions, please feel free to send me a message. Viewing on site by appointment possible. Further metalworking machinery such as bench drills, press brakes, column drilling machines, eccentric presses, heavy-duty racking, welding tables, MIG welders, compressors, etc. – please take a look at my other listings. Location for viewing and collection: 12277 Berlin Domestic price net plus VAT or Net export price Collection only – dismantling and transport by buyer or by arrangement. If you are interested or have any questions, please feel free to send me a message. Further photos and technical details available on request. All information is subject to change without notice. Errors and prior sale reserved. For further questions, please call Nous parlons Français / Мы говорим по-русски We speak English / Noi vorbim românește Viber / WhatsApp / Skype We handle all customs and registration matters for an additional charge. For an extra fee, we can transfer the vehicles to the port.

Condition: good (used), functionality: fully functional, Year of construction: 2003, Pressure: 225 t Bending length: 2050 mm Distance between uprights: 1550 mm Control: CYBELEC DNC 1200 PS Eco Stroke: 550 mm Table height: 700 mm Throat depth: 405 mm Distance table/ram: 320-870 mm Frame throat depth: 405 mm Machine weight approx.: 14,000 kg Accessories/Equipment: - Controlled axes: Y1 - Y2 - X - R - Z1 and Z2 manually adjustable - Lasersafe angle measurement Lajdpfowvi Uvsx Agzsk - Pneumatically adjustable support table - Pneumatic upper and lower tool clamping - Two-hand foot pedal operation - Manual crowning

Condition: used, Year of construction: 2003, Max. cutting length: 6075 mm Max. sheet thickness: 4 mm steel Controlled back stop up to 1000 mm Light barrier Sheet metal holding Few operating hours Machine is loaded free Laodpfx Astuna Eogzok

Condition: ready for operation (used), Year of construction: 2000, pressure 85.0 t chamfer lenght 2050 mm distance between columns 1650 mm column arm 400 mm stroke 240 mm dayligth 320 - 560 mm ajustment speed 150 mm/sec working feed 15.0 mm/sec return speed 150 mm/sec back stop - adjustable 5.0 - 1000 mm table width 110 mm work height max. 1050 mm operating pressure max. 297 bar compressed air 4.5 - 6.0 bar oil volume 200 l operating pressure 340 bar total power requirement 7.5 kW weight of the machine ca. 5900 kg range L-W-H 4100 x 2100 x 2750 mm with increased installation height / piston stroke well-maintained condition (!!) Lodpfx Aoxab Ugsgzeak - in checked condition - machine video - ?v=ikl6RNZWeiU Equipment: - CNC electro-hydraulic press brake - including CYBELEC CNC control * swiveling control panel at the front right * external screen - CNC axis adjustment: Y1 - Y2 - X - R - Z1 - Z2 - I + CNC crowning - CNC electro-motorized back stop (X axis) * Travel range .. 5.0 - 1,000 mm * Travel speed .. 250 mm/sec. - CNC electro-motorized height adjustment of the back stop (R axis) * Travel range .. 70 - 235 mm * Travel speed .. 100 mm/sec. - CNC electro-motoric adjustment of the stop fingers (Z axes) * Travel range Z1 .. 405 - 1.565 mm * Travel speed .. 1.000 mm/sec. * Travel range Z2 .. 485 - 1.645 mm * Travel speed .. 1.000 mm/sec. - CNC electro-motoric table crowning - CNC pneumatic die displacement (I axis) - EHT pneumatic tool clamping - upper tool - EHT manual tool clamping - lower tool * Tool holder 90.0 mm + 13.0 mm possible - 1x freely movable 2-hand/foot control - 2x front, stable support arms including "sliding system" - side protective device (swinging doors) - rear protective device (swinging door) - original operating instructions + circuit diagram etc. * Special accessories included: - Oil cooler for use in continuous operation

Condition: excellent (used), functionality: fully functional, Year of construction: 1994, EHT hydraulic guillotine shear type TSS 3-40, working width 4100 mm, max. sheet thickness 3.0 mm, pneumatic sheet support device, NC controlled backgauge, support arms, extra set of blades. Lsdpfxjw Uf Nre Agzoak

Year of construction: 1990, condition: used, pression: 250 t working width: 3550 mm clear support width: 3050 mm Lsdpfo Dqaqox Agzjak support throat: 300 mm rear stop: ja mm electrical connection: 400 V, ca. 26 kW weight: 20 t space needed: 2100 x 3800 x 3100 mm

Condition: excellent (used), Year of construction: 2001, sheet thickness steel (max.): 6 mm, cutting length (max.): 3,050 mm, Equipment: finger protection, Hydraulic guillotine shear Manufacturer EHT Type. TSS 6-30 Year of manufacture 2001 Technical data Make: EHT Type: TSS 6 - 30 Year of manufacture: 2001 Usable length: 3050 mm Sheet thickness: 6 mm Motor: 11 kW Oil quantity 250 L Dimensions: L 3.70 x W 2.15 (plus stop arms 1m, plus grid 0.6m) x H 2.15 m Weight: approx. 8 t Equipment • Angle stop • 3 support arms • Controlled rear stop 10-1000mm • Control Elgo P8721 • Pneumatic holding device with scrap chute • Cutting edge lighting • Rear area protection via light barrier • Cutting length adjustment All information without guarantee. Ledpfsvkd Etsx Agzsak A demonstration is possible at any time in our exhibition hall.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1997, operating hours: 4,125 h, working width: 3,050 mm, sheet thickness (max.): 13 mm, back gauge: 1,000 mm, TECHNICAL DETAILS Sheet width: 3,050 mm Sheet thickness: 13 mm Back gauge – electric: 10–1,000 mm Strokes: 16 strokes/min Control: Elgo MACHINE DETAILS Total power requirement: 22 kW Operating hours: approx. 4,124 h EQUIPMENT - Automatic cutting gap adjustment - Sheet lifting device - Foot switch - Digital back gauge 1,000 Elgo Lasdsww E Nxepfx Agzok - Scrap chute - Rear safety guards - Angle stop - Material support arms

Year of construction: 1998, condition: good (used), functionality: fully functional, machine/vehicle number: 107856, new seals on hydraulic cylinders TECHNICAL DETAILS Laodpfxsl N Ufyj Agzjk material length: 6050 mm sheet thickness: 6 mm (450 N/qmm) passage: 6050 mm upright projection: 100 mm Control system: ELGO P8721 number of support arms: 4 stop range (from cutting line): 10 - 1000 mm Adjustment speed: 70 mm/s MACHINE DETAILS machine length: 7000 mm machine width (without support arms): 2350 mm machine width with supporting arms: 3440 mm machine height: 2550 mm Machine weight: 21000 kg Oil tank. 300 l Connected load: 18 kW Material: aluminum 1,2 mm EQUIPMENT motorized backgauge 1 side stop sheet holding-up system

Condition: used, Year of construction: 1985, sheet width 3100 mm plate thickness 4.0 mm thickness at "Niro-steel" 2.5 mm cutting angle adjustment 1.0 ° back stop - adjustable 10 - 1000 mm adjustment speed 180 mm/s down holder 21 Stück strokes per minute 18 - 31 oil volume 160 L Control ELGO P8511 column arm 200 mm distance between columns 3050 mm 0 max. 300 bar voltage 400 V main drive 9.0 kW weight of the machine ca. 4800 kg. Lodpfx Aoxab Tvegzoak dimensions of the machine ca. 3660 x 2070 x 2140 mm from a maintenance workshop Equipment: - electro-hydraulic sheet metal shear "swing cut" - machine frame = all-steel welded construction - ELGO NC control model P8511, control panel at the front left * for positioning the electro-motoric rear stop * target/actual position value input possible * adjustment by three-phase motor via toothed belt - support table with ball rollers * there are recessed grips between the table plates - front finger guard - hydraulically acting sheet metal hold-down device - 1x freely movable foot switch - emergency stop button at the front - movable scrap switch - original operating instructions + circuit diagram Special accessories included: - EHT pneumatic sheet metal holding device for thin sheet metal cuts - 1x EHT extra long side stop 3.000 mm with mm scale & support foot - 1x EHT extra long support arm with 3.000 mm with scale & Support foot - EHT additional support arms with mm scale

Year of construction: 1987, condition: ready for operation (used), An EHT hydraulic guillotine shear refurbished in 2023 is available. Cutting length: 3000mm, max. sheet thickness steel/VA: 4mm/2mm, backgauge: 10mm-1000mm, adjustment speed: 180mm/s, stroke rate: 18-31 strokes/min, oil volume: 160l. Machine dimensions X/Y/Z: approx. 3700mm/2100mm/2150mm, weight: approx. 4800kg, operating hours: 44024h. The cylinders, blades and hoses were overhauled in 2023. On-site inspection is possible. Lodpfxswrhwus Agzeak

Condition: good (used), Year of construction: 1999, cutting width: 6.050 mm Laedewzvntepfx Agzsk cutting thickness: max. 4 mm length stop range: 10 - 1.000 mm

Year of construction: 1995, condition: ready for operation (used), Pressing force: 200t/2000kN, bending length: 3550mm, upright distance: 3050mm, upright projection: 350mm, max. ram stroke: 200mm, max. ram-to-table distance: 540mm. Dimensions X/Y/Z: approx. 4400mm/2100mm/3200mm, weight: approx. 16000kg, control: Cybelec DNC 800. Including a matrix, 2x upper tool (30°/60°) and a new light barrier. Documentation available. On-site inspection is possible. Laodpfx Agotva Dnjzek

Condition: used, Year of construction: 1997, pressure 225 t chamfer lenght 3050 mm distance between columns 2550 mm column arm 300 mm ajustment speed 110 mm/sec work speed 9.0 mm/sec return speed 130 mm/sec work stroke 240 mm dayligth 320 - 560 mm table height 1000 mm table width 200 mm oil volume 350 ltr. operating pressure max. 296 bar air pressure 4.5 - 6.0 bar voltage 400 Volt total power requirement 18.5 kW weight 14900 kg range L-W-H 5180 x 2400 x 3100 mm - in checked condition - machine video - ?v=ebbbzSYMxKw Furnishing: - electro-hydraulic CNC die bending/press brake - CYBELEC CNC control "ModEva 12S", swiveling at the front right * High-resolution graphic color screen 14 inches Lodexaa Dtspfx Agzjak * Representation as a line, area or volume drawing of the product * Clear, concise menus in the operator's language * Large tools and products library - CNC-controlled back gauge adjustment (X-axis) * Stop range X axis of bending line .. 5.0 - 1.000 mm * Adjustment speed .. max. 250 mm/sec. - CNC-controlled vertical adjustment of the stop fingers (R axis) * Adjustment range of table surface .. 115 - 265 mm * Adjustment speed .. max. 100 mm/sec. * Adjustment via SERVO motors - CNC-controlled adjustment of the stop fingers left-right (Z1+Z2 axis) * Adjustment range Z1 .. 405 - 2565 mm * Adjustment range Z2 .. 485 - 2645 mm * Adjustment speed .. max. 1000 mm/sec. - WILA CNC-controlled electric table crowning - pneumatic EHT upper tool clamping - manual lower tool clamping - 1x freely movable 2 hand/foot control - 2x front, movable support arms - rear protective device (sliding protective grille) - side protection device (pivoting protective grille) - 1x set of EHT deer foot upper tool - split (3.000 mm) - 1x set of EHT lower tools - split (3.000 mm) - original operating instructions (machine + control)

Condition: excellent (used), Year of construction: 1998, pressing force: 125 t, Hydraulic press brake Fab. EHT Typ. VARIOPRESS 125-3550 Year 1998 Technical data Laodsr Epr Ujpfx Agzek Make: EHT Type: Variopress 125-3550 Year of construction: 1998 Capacity: 125 t Effective length: 3550 mm Machine column: 2550 mm Projection: 300 mm Stroke: 240 mm Installation height: 640 mm Oil volume 250 L Dimensions: approx. L 3.90 x W 1.80 x H 3.00 m Weight: approx. 12 t Equipment - Control system: Cybelec DNC 80 2D graphics - Automatic upper tool clamping - Lower tool clamping 90mm and 13mm - controlled axes: Y1, Y2, X1, X2, R, Z1, Z2 - motorized crowning - 6 x V block die length 3,500, segmented: with V12/30°, V40/80°, V24/80°, V10/30°, V24/30°, V16/30° - Punch straight, H 350mm / approx. 70°, length 3060 mm, segmented All data without guarantee. A demonstration under power is possible at any time in our exhibition hall.

Condition: new, functionality: fully functional, Year of construction: 2004, Pressing force: 225 t Bending length: 3050 mm Distance between uprights: 2550 mm Control type: DNC 1200PS Eco/Col Ram stroke: 700 mm Throat depth: 405 mm Distance table/ram: min. 320 / max. 1020 mm Total power requirement: 29.5 kW Machine weight approx.: 15,500 kg Accessories/Equipment: Rear gauge Backgauge traverse adjustment: - X-axis gauging range (from bending line): 5–1000 mm - X-axis adjustment speed: max. 500 mm/sec Height adjustment: - R-axis adjustment range (from table surface): 85–235 mm - R-axis adjustment speed: max. 150 mm/sec Backgauge finger adjustment: - Z1-axis adjustment range (from left table front): 520–2365 mm - Z1-axis adjustment speed: max. 1000 mm/sec - Z2-axis adjustment range (from left table front): 690–2535 mm - Z2-axis adjustment speed: max. 1000 mm/sec - X1-axis adjustment range (from center line): ± 125 mm - X1-axis adjustment speed: max. 250 mm/sec Lodpfx Agsxb Tftszjak Die shifting – adjustment via rear gauge (MVX): - Adjustment range: max. 100 mm - Adjustment speed as per X-axis: 500 mm/sec Front support/press brake aides: - Swivel angle BV1/BV2-axis: 55° - Swivel speed BV1/BV2-axis: max. 45°/sec - Lifting force per swivel arm BV1/BV2-axis: max. 1,500 N

Condition: good (used), Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams, hydraulic buffers, pressure boosting cylinders Laedpegxnkcofx Agzek -Hydraulic cylinder: from press brake EHT type EHP 11-40 -Piston rod: Ø 155 mm -Stroke: 250 mm -Number: 2x cylinders available, 1x left / 1x right -Price per piece -Dimensions .: 855/285/380 mm -Weight: 311 kg / pc.

Condition: good (used), functionality: fully functional, Year of construction: 2001, pressing force: 225 t, working length: 6,050 mm, TECHNICAL DETAILS Axes controlled: Y1, Y2, X, R, Z1, Z2 Pressure: 225 t Bending length: 6050 mm Control: CYBELEC DNC 1200 PS Dimensions: 6,050 x 2,150 x 3,167 mm Total power requirement: 18.5 kW EQUIPMENT - 2 bending aids in front of the machine - 2 support arms in front of the machine - pneumatic tool clamping at the top - crowning, die shifting - foot switch Tool holder: - top: 26 mm EHT - bottom: 55 mm EHT Laodpfx Agjvuq Naezsk Please note: This machine is an underfloor machine

Condition: ready for operation (used), Year of construction: 2001, pressure 135 t chamfer lenght 3050 mm distance between columns 2550 mm dayligth 320 - 560 mm stroke 240 mm working feed 10.0 mm/sec return speed 150 mm/sec column arm 400 mm work height max. 1050 mm control DNC 1200 PS/B operating pressure max. 297 bar compressed air 4.5 - 6.0 bar connected load 15.0 kW oil volume 250 ltr. weight 11500 kg range L-W-H 5240 x 2400 x 2900 mm good/well-Maintained conditions used in Aluminum processing - in checked conditions - machine Video - ?v=z-Bxibk_8uE Features: - CNC Electro-Hydraulic Press Brake - CYBELEC CNC Control Model DNC 1200 PS/B * Swiveling Control Panel, Front Right * Numerical Programming * Tool & Program Library - CNC Controlled Axes: Y1 + Y2 + X + R + CNC Crowning - CNC Electro-Motorized Backgauge (X-Axis) * with 3x Manually Adjustable Backgauge Fingers (Z-Axis) * Maximum Travel Speed: 250 mm/sec - CNC electro-motorized height adjustment from the backgauge (R-axis) * Maximum travel speed: 100 mm/sec. - CNC under-table crowning - CNC pneumatic die shifting (I-axis) - Pneumatic upper tool clamping Lodpfxjx Ik D As Agzeak - Pneumatic lower tool clamping - Rear safety guard, including swiveling door - 2x side safety guards - includes LAZER SAFE safety device - front - 2x stable front support arms with sliding system - original EHT split upper and lower tools - 1x freely movable 2-hand/foot control - Wiring diagram + hydraulic diagram

Condition: excellent (used), EHT Guillotine Shears Brand: Eisen u. Hammerwerk (EHT) Lodpfjwc Rgajx Agzoak Type: ASS 8-30 Year of manufacture: 1967 Serial number: 10625 Cutting length: 3000 mm Max. sheet thickness: 8 mm Motor power: 11 kW Connection: 380 V Dimensions: 3950 x 3100 x 1900 mm

Condition: good (used), Year of construction: 2000, sheet width 3050 mm plate thickness 10.0 mm thickness at "Niro-steel" 6.0 - 8.0 mm down holder 13 Stück distance between columns 3070 mm cutting angle 1.0 - 4.0 ° no. of strokes ~ 22 Hub/min Control ELGO P8511 oil volume 240 l voltage 400 V total power requirement 15.0 kW weight 8000 kg range L-W-H 3550 x 2350 x 1900 mm good / well-maintained condition with special accessories (!!) Equipment: - NC electro-hydraulic guillotine shears - heavy / stable welded construction (machine body) - NC ELGO digital control unit "P8511" - NC electro-motorized backgauge on ball screws - electro-hydraulic cutting angle adjustment * Front analog cutting angle display - 1x stable side stop, with T-slot and mm scale - 3x stable support arms, with T-slot and mm scale - Ball castors in the work table incl. recessed grips - Front finger guard - can be folded up at the front Laedpox Emqyjfx Agzek - 1x freely movable foot switch - 2x front EMERGENCY OFF button - Operating instructions (PDF)