Used Eht Tss 4-40 for sale (53)

Condition: used, Year of construction: 1985, sheet width 3100 mm plate thickness 4.0 mm thickness at "Niro-steel" 2.5 mm cutting angle adjustment 1.0 ° back stop - adjustable 10 - 1000 mm adjustment speed 180 mm/s down holder 21 Stück strokes per minute 18 - 31 oil volume 160 L Control ELGO P8511 column arm 200 mm distance between columns 3050 mm 0 max. 300 bar voltage 400 V main drive 9.0 kW weight of the machine ca. 4800 kg. dimensions of the machine ca. 3660 x 2070 x 2140 mm from a maintenance workshop Equipment: - electro-hydraulic sheet metal shear "swing cut" - machine frame = all-steel welded construction - ELGO NC control model P8511, control panel at the front left * for positioning the electro-motoric rear stop * target/actual position value input possible * adjustment by three-phase motor via toothed belt - support table with ball rollers * there are recessed grips between the table plates - front finger guard - hydraulically acting sheet metal hold-down device - 1x freely movable foot switch - emergency stop button at the front - movable scrap switch - original operating instructions + circuit diagram Bjdpfx Agsxab Tvjljcu Special accessories included: - EHT pneumatic sheet metal holding device for thin sheet metal cuts - 1x EHT extra long side stop 3.000 mm with mm scale & support foot - 1x EHT extra long support arm with 3.000 mm with scale & Support foot - EHT additional support arms with mm scale

Condition: good (used), Year of construction: 1999, cutting width: 6.050 mm Bedpfx Agjwzvntslocu cutting thickness: max. 4 mm length stop range: 10 - 1.000 mm

Year of construction: 1987, condition: ready for operation (used), An EHT hydraulic guillotine shear refurbished in 2023 is available. Cutting length: 3000mm, max. sheet thickness steel/VA: 4mm/2mm, backgauge: 10mm-1000mm, adjustment speed: 180mm/s, stroke rate: 18-31 strokes/min, oil volume: 160l. Machine dimensions X/Y/Z: approx. 3700mm/2100mm/2150mm, weight: approx. 4800kg, operating hours: 44024h. The cylinders, blades and hoses were overhauled in 2023. On-site inspection is possible. Bedpfewrhwusx Aglscu

Condition: ready for operation (used), Press force: 250 t greatest working length: 4050 mm Bedpfxjx Tr Ugs Aglocu equipped with CYBELEC DNC 70 PSG control

Condition: good (used), Stop for press brake, bending machine, guillotine shear, drive shaft -Drive shafts: for stop, from press brake EHT type EHP 11-40, 2 pieces -Length: 515 mm -Hole: Ø 25 mm -Price: complete -Dimensions: Ø 50 x 515 mm Bcedogxnkkjpfx Aglju -Weight 5.1 kg/pc.

Condition: good (used), Hydraulic cylinders, support cylinders, hydraulic pistons, pressure pistons, hydraulic buffers, pressure boosting cylinders -Hydraulic cylinder: from press brake EHT type EHP 11-40 -Piston rod: Ø 155 mm -Stroke: 250 mm -Number: 2 cylinders available, 1 left / 1 right -Price: per piece -Dimensions: 855/285/380 mm Bcedpfx Aegxnkcsgleu -Weight: 311 kg/unit

Condition: used, Year of construction: 1996, pressure 175 t chamfer lenght 4050 mm distance between columns 3050 mm column arm 300 mm ajustment speed 140 mm/sec work speed 10.0 mm/sec return speed 130 mm/sec work stroke 360 mm dayligth 340 - 700 mm table height 1000 mm table width 200 mm oil volume 300 ltr. Bcjdpoxab Exefx Aglou operating pressure max. 295 bar air pressure 4.5 - 6.0 bar voltage 3x 400 Volt total power requirement 15.0 - 27.0 kW weight 17200 kg range L-W-H 5850 x 2550 x 3200 mm good condition (!!) including new CNC control - in checked condition - machine video - ?v=Owh6BjvZ4RM Equipment: - electro-hydraulic CNC press brake - with new CYBELEC "VisiTouch 19" touch CNC control (conversion) * graphic numerical 2D control * 19? modern, streamlined touchscreen with glass surface * can also be operated with gloves * clear, well-arranged menus in the operator's language * easy operation thanks to the user-friendly HMI * large tool and product library - CNC controlled axes: * Y1+Y2 / X+X1 / R / Z1+Z2 / BV1+BV2 / I + CNC crowning - CNC electro-motoric back stop adjustment (X-axis) * Stop range X axis of bending line .. 5.0 - 1.000 mm * Adjustment speed .. max. 500 mm/sec. * Adjustment in X1 axis possible .. +/- 125 mm - CNC-controlled vertical adjustment of the stop fingers (R axis) * Adjustment range of table surface .. 85 - 235 mm * Adjustment speed .. max. 100 mm/sec. - CNC-controlled adjustment of the stop fingers left-right (Z1+Z2 axis) - CNC-controlled / pneumatic die displacement (I axis) - 2x CNC-controlled front bending aids (BV axes) * Swivel angle max. .. 45 degrees * Swivel speed .. max. 45 degrees/sec. - CNC-controlled electric table crowning - pneumatic EHT upper tool clamp - pneumatic EHT lower tool clamp - 1x freely movable 2-hand/foot control - rear protective device (protective grille) - side protective device (swivel doors) - various bending tools - original operating instructions + circuit diagram etc.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2009, controller model: Cybelec ModEva 10S, bending force (max.): 170 t, empty load weight: 16,300 kg, working length: 4,050 mm, TECHNICAL DETAILS Press force: 170 t Bending length: 4,050 mm MACHINE DETAILS Control: Cybelec ModEva 10S Machine weight: 16,300 kg EQUIPMENT Lasersafe 2 sheet supports Die shifting Crowning Pneumatic tool clamping top and bottom Bcsdpfx Agexwnv Ejlou Controlled axes: Y1, Y2, X, R, Z1, Z2 Tool cabinet with tools

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1995, controller model: Cybelec ModEva 19 T, bending force (max.): 300 t, distance between stands: 3,550 mm, oil tank capacity: 400 l, working length: 4,050 mm, The machine control was renewed in 2022! TECHNICAL DETAILS Press force: 300 t Bending length: 4,050 mm Distance between uprights: 3,550 mm Oil capacity: 400 l MACHINE DETAILS Control system: Cybelec ModEva 19 T Total power requirement: 22 kW Machine weight: approx. 20,000 kg EQUIPMENT 2 bending aids Matrix displacement Pneumatic tool clamping, top and bottom Crowning Controlled axes: y1, y2, x, R, z1, z2 Two-hand foot control 2 parking stations for bending aid Bcedpexwnqcefx Aglsu

Condition: good (used), functionality: fully functional, Year of construction: 1995, Pressure: 300 t Bending length: 4050 mm Distance between columns: 3550 mm Oil capacity: 400 l Control: MOD EVA 19T Total power requirement: 22 kW Machine weight approx.: 20,000 kg Equipment: Bcsdpfexu I Uvjx Agleu - CNC control Cybelec ModEva 19 T - 2 bending aids - Die shifting - Pneumatic tool clamping (top and bottom) - Crowning system - Controlled axes: y1, y2, x, R, z1, z2 - Two-hand and foot control - 2 parking stations for bending aid

Condition: good (used), functionality: fully functional, Year of construction: 2008, Press force: 170 t Bending length: 4050 mm Machine weight approx.: 16,300 kg Control: ModEva 10S Equipment: - CNC control Cybelec ModEva 10S - Lasersafe - 2 sheet supports - Die shifting - Crowning system - Pneumatic tool clamping (top and bottom) Bsdpfjxu I Ucex Agljcu - Controlled axes: y1, y2, x, R, z1, z2 - Tool cabinet with tools

Condition: used, functionality: fully functional, Year of construction: 1987, machine/vehicle number: 101536, Offered for sale is a hydraulic guillotine shear Manufacturer: Eisen und Hammerschmidt GmbH Model: TSS4-20 Year of manufacture: 1987 Serial No.: 101536 Capacity: 4 mm Working width: 2,000 mm Control: ELGO Type P8511 Light curtain system by SICK Used, fully functional condition. Collection by purchaser; assistance with dismantling/transport can be arranged if required. — If you are interested or have any questions, please feel free to send me a message. Viewing on site by appointment possible. Further metalworking machinery such as bench drills, press brakes, column drilling machines, eccentric presses, heavy-duty racking, welding tables, MIG welders, compressors, etc. – please take a look at my other listings. Location for viewing and collection: 12277 Berlin Domestic price net plus VAT or Net export price Collection only – dismantling and transport by buyer or by arrangement. If you are interested or have any questions, please feel free to send me a message. Further photos and technical details available on request. All information is subject to change without notice. Errors and prior sale reserved. For further questions, please call Nous parlons Français / Мы говорим по-русски We speak English / Noi vorbim românește Viber / WhatsApp / Skype Bjdpfxex Da D Uo Aglecu We handle all customs and registration matters for an additional charge. For an extra fee, we can transfer the vehicles to the port.

Condition: used, Year of construction: 1986, machine/vehicle number: 200485, Lg.no. 24243 Technical data: - max. working length 4050 mm - upright clearance 3050 mm - max. pressing force 110 t - ram stroke 200 mm - throat 350 mm - Table height 900 mm - Opening width 400 mm Bcedpfx Agstqmvzslou - Drive power 17.5 kW - Space requirement approx. W 4250 x H 2850 x D 2200 mm - Weight approx. 15.0 t - with: - CYBELEC ModEva 10 S control unit renewed in 2011 - Y 1+ 2 , X , Z - Two-hand control panel: - Mot. backgauge 5 - 1000 mm - front support arms - split pointing tool, - universal die

Condition: used, Year of construction: 1994, sheet width / mm plate thickness / mm distance between columns / mm Manufacturer: EHT Bcsdpfx Asuddh Aeglou Type: TSS 20-25 Year of construction: 1994 Max. Cutting length: 2250 mm Max. Sheet thickness: 20 mm Strip width min / max: 10/1000 mm Distance between the consoles: 2530 Height above the ground: 900 mm Table length without extension arms: 3030 mm Oil volume: 800 l Max. Pressure: 280 bar Operating voltage: 400V Control voltage: 230 V. Nominal current: 87 A. Weight: 15.8 to Dimensions L x W x H: 3500 x 2500 x 2400 mm Accessories / special equipment Pneumatic cutting gap adjustment Cutting length limitation Roller conveyor elevation bracket Hand protection 1 bay Multitron control Multitron PS 80; ELCO 85 P Lower knife height adjustment

Condition: used, Year of construction: 1999, sheet width 3200 mm plate thickness 4.0 mm ST distance between columns 3300 mm upper clamping bar adjustment 400 mm Adjustment folding beam 80.0 mm pivoting angle 180 Grad clamping capacity max. 200 KN Bjdpfxsxaa A Ns Aglocu rear stop 10.0 - 1600 mm oil volume 160 Liter total power requirement 9.8 kW weight 8500 kg range L-W-H ~ 4900 x 2000 x 2300 mm From a maintenance workshop Good / well-maintained condition (!!) - in checked conditions - machinevideo - ?v=RY-amZooeX4 Equipment: - Robust CNC folding machine - CNC control unit - CYBELEC "DNC 80 PP" * Swiveling control panel, front right * 2D graphic display for display and multiple simulation * 2D graphic programming * Easy handling - CNC electro-motorized backgauge * Travel range 10.0 - 1,600 mm * Pneumatic / lowerable stop fingers * Adjustment speed max. 250 mm/sec. * Rear sheet support table with brushes - Electro-motorized lower beam adjustment (S axis) - Electro-hydraulic pivoting movement of the lower beam - Pneumatic upper tool clamping - Pneumatic lower tool clamping - 1x freely movable double foot switch - Original operating instructions + wiring diagram/hydraulic diagram Special accessories included: - 1x split set of goat's foot upper tools, H = 150 mm (not complete) - 1x split set of goat's foot upper tools, H = 200 mm (not complete) - 1x split bending/lower tool - Rear sheet support with brushes

Condition: used, Year of construction: 1971, sheet width 2000 mm plate thickness 16 bei St 42 mm passage width 2250 mm impact length 1000 mm blade length 2005 mm throat 600 mm cutting gap adjustment 0,05 - 0,95 mm cutting angle 1° 40' ° Bodeww Nccepfx Aglecu down holder 10 Stück back stop - adjustable 10 - 1000 mm table: 2500 x 700 table height over floor 800 mm quantity of oil 900 l weight of the machine ca. 10 t dimensions of the machine ca. 3 x 2,3 x 2,3 m voltage 380 V Food switch, material support beams, spare knifes.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1997, operating hours: 4,125 h, working width: 3,050 mm, sheet thickness (max.): 13 mm, back gauge: 1,000 mm, TECHNICAL DETAILS Sheet width: 3,050 mm Bcedpfx Agoww E Nxeleu Sheet thickness: 13 mm Back gauge – electric: 10–1,000 mm Strokes: 16 strokes/min Control: Elgo MACHINE DETAILS Total power requirement: 22 kW Operating hours: approx. 4,124 h EQUIPMENT - Automatic cutting gap adjustment - Sheet lifting device - Foot switch - Digital back gauge 1,000 Elgo - Scrap chute - Rear safety guards - Angle stop - Material support arms

Year of construction: 1998, condition: good (used), functionality: fully functional, machine/vehicle number: 107856, new seals on hydraulic cylinders TECHNICAL DETAILS material length: 6050 mm sheet thickness: 6 mm (450 N/qmm) passage: 6050 mm upright projection: 100 mm Control system: ELGO P8721 number of support arms: 4 stop range (from cutting line): 10 - 1000 mm Adjustment speed: 70 mm/s MACHINE DETAILS machine length: 7000 mm machine width (without support arms): 2350 mm machine width with supporting arms: 3440 mm machine height: 2550 mm Machine weight: 21000 kg Bcodpfxsl N Ufye Aglou Oil tank. 300 l Connected load: 18 kW Material: aluminum 1,2 mm EQUIPMENT motorized backgauge 1 side stop sheet holding-up system

Condition: not inspected (used), Year of construction: 1992, CNC folding machine make: EHT, type: EHPS 11 - 45, SN: 206882, year: 1992, pressure capacity: 1,100 kN, working range: 4,450 mm, CNC control Cybelec, 2-hand operation, safety device make: Trumpf, retrofitted in 2023, last maintenance in 2023 by Trumpf for approx. €10,000.00, Bcsdpfx Aov Duu Ejglou Note: Machine already professionally dismantled and ready for transport

Condition: used, Year of construction: 1971, total length: 3,000 mm, total width: 2,000 mm, total height: 3,000 mm, Weight: 10.000 kg - Year: 1971 Bcsdsybdknepfx Aglju - Documentation available: No - CE certificate present: No - Serial number: 20956 - Drive system: Teach-in - Control system brand: Unimec - Number of axes [pcs]: 3: Y1+Y2+X - Press force [ton]: 150 - Max. working width [mm]: 3050 - Column gap [mm]: 2500 - Backgauge depth [mm]: 750 - Crowning system: None - Punch holder: Standard - Tools included: Yes - Transport dimensions: 3000mm x 2000mm x 3000mm (l x w x h) - Transport weight [kg]: 10000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Year of construction: 2003, operating hours: 3,542 h, condition: ready for operation (used), This EHT ECOCUT was manufactured in 2003. A robust hydraulic shearing machine, it features a cutting length of 3,050 mm and a thickness capacity of 13 mm. It operates with an 18.5 kW main motor and includes an ELGO P8511 control for precision. Consider the opportunity to buy this EHT ECOCUT hydraulic shearing machine. Contact us for more information. • Cutting capacity: • Cutting length: 3,050 mm • Cutting thickness: 13 mm • Material tensile strength: 450 N/mm² • Hydraulic system: • Oil volume: 300 liters Bcodpfx Ajycfq Soglou • Electrical data: • Current type: AC • Frequency: 50 Hz • Operating voltage: 400 V • Control voltage: 24 V DC • Rated current: 45 A • Main fuse rated current: 63 A • Main motor power: 18.5 kW • Control / documentation: • Control type: ELGO P8511 (NC backgauge control) • Electrical circuit diagram no.: 111 796

Condition: good (used), Year of construction: 2000, Punching press Manufacturer: EHT Bcedpfsul S Eajx Aglsu Model: Strippit 1500/30 Year of manufacture: 2000 CNC control: Fanuc Working area without repositioning: 2500 x 1500 mm Maximum material thickness: 8 mm Punching force: 30 t Turret with 46 tool stations, including 4 D-size index stations 3 programmable clamps Metal table Used exclusively in single-shift operation Including WILSON TOOL tooling

Condition: good (used), Year of construction: 1987, fabric-no. 202 395 working length 2550 mm output 2000 KN tracking travel 13 mm Bsdoq Awh Repfx Aglecu safety distance 176 mm

Condition: used, Bending tool, die, upper knife, upper tool, straight tool, die tool, seam closing tool -Tool: from press brake EHT type EHP 11-40 Bcedpfegxnkvjx Agleu -Measures: see drawing in the photos -Dimension: 4050/45 / H130 mm -Weight: 147 kg

Condition: ready for operation (used), Year of construction: 2000, pressure 85.0 t chamfer lenght 2050 mm distance between columns 1650 mm column arm 400 mm stroke 240 mm dayligth 320 - 560 mm ajustment speed 150 mm/sec working feed 15.0 mm/sec return speed 150 mm/sec back stop - adjustable 5.0 - 1000 mm table width 110 mm work height max. 1050 mm operating pressure max. 297 bar compressed air 4.5 - 6.0 bar oil volume 200 l operating pressure 340 bar total power requirement 7.5 kW weight of the machine ca. 5900 kg range L-W-H 4100 x 2100 x 2750 mm with increased installation height / piston stroke well-maintained condition (!!) Bodsxab Ugjpfx Aglocu - in checked condition - machine video - ?v=ikl6RNZWeiU Equipment: - CNC electro-hydraulic press brake - including CYBELEC CNC control * swiveling control panel at the front right * external screen - CNC axis adjustment: Y1 - Y2 - X - R - Z1 - Z2 - I + CNC crowning - CNC electro-motorized back stop (X axis) * Travel range .. 5.0 - 1,000 mm * Travel speed .. 250 mm/sec. - CNC electro-motorized height adjustment of the back stop (R axis) * Travel range .. 70 - 235 mm * Travel speed .. 100 mm/sec. - CNC electro-motoric adjustment of the stop fingers (Z axes) * Travel range Z1 .. 405 - 1.565 mm * Travel speed .. 1.000 mm/sec. * Travel range Z2 .. 485 - 1.645 mm * Travel speed .. 1.000 mm/sec. - CNC electro-motoric table crowning - CNC pneumatic die displacement (I axis) - EHT pneumatic tool clamping - upper tool - EHT manual tool clamping - lower tool * Tool holder 90.0 mm + 13.0 mm possible - 1x freely movable 2-hand/foot control - 2x front, stable support arms including "sliding system" - side protective device (swinging doors) - rear protective device (swinging door) - original operating instructions + circuit diagram etc. * Special accessories included: - Oil cooler for use in continuous operation