Used Eht Tss 16-20 for sale (55)

Condition: used, Year of construction: 1971, sheet width 2000 mm plate thickness 16 bei St 42 mm passage width 2250 mm impact length 1000 mm blade length 2005 mm throat 600 mm cutting gap adjustment 0,05 - 0,95 mm cutting angle 1° 40' ° down holder 10 Stück back stop - adjustable 10 - 1000 mm table: 2500 x 700 table height over floor 800 mm quantity of oil 900 l weight of the machine ca. 10 t dimensions of the machine ca. 3 x 2,3 x 2,3 m voltage 380 V Gjdpfx Aeww Nccsh Eobw Food switch, material support beams, spare knifes.

Condition: used, Year of construction: 1994, sheet width / mm plate thickness / mm distance between columns / mm Manufacturer: EHT Type: TSS 20-25 Year of construction: 1994 Max. Cutting length: 2250 mm Max. Sheet thickness: 20 mm Strip width min / max: 10/1000 mm Distance between the consoles: 2530 Height above the ground: 900 mm Table length without extension arms: 3030 mm Oil volume: 800 l Max. Pressure: 280 bar Operating voltage: 400V Control voltage: 230 V. Gsdouddh Aepfx Ah Eebw Nominal current: 87 A. Weight: 15.8 to Dimensions L x W x H: 3500 x 2500 x 2400 mm Accessories / special equipment Pneumatic cutting gap adjustment Cutting length limitation Roller conveyor elevation bracket Hand protection 1 bay Multitron control Multitron PS 80; ELCO 85 P Lower knife height adjustment

Condition: used, Year of construction: 2003, Max. cutting length: 6075 mm Max. sheet thickness: 4 mm steel Controlled back stop up to 1000 mm Light barrier Gedpfxjtuna Es Ah Eobw Sheet metal holding Few operating hours Machine is loaded free

Condition: used, Year of construction: 1985, sheet width 3100 mm plate thickness 4.0 mm thickness at "Niro-steel" 2.5 mm cutting angle adjustment 1.0 ° back stop - adjustable 10 - 1000 mm adjustment speed 180 mm/s down holder 21 Stück strokes per minute 18 - 31 oil volume 160 L Control ELGO P8511 column arm 200 mm distance between columns 3050 mm 0 max. 300 bar voltage 400 V main drive 9.0 kW weight of the machine ca. 4800 kg. dimensions of the machine ca. 3660 x 2070 x 2140 mm from a maintenance workshop Equipment: - electro-hydraulic sheet metal shear "swing cut" Gedpfjxab Tvox Ah Eebw - machine frame = all-steel welded construction - ELGO NC control model P8511, control panel at the front left * for positioning the electro-motoric rear stop * target/actual position value input possible * adjustment by three-phase motor via toothed belt - support table with ball rollers * there are recessed grips between the table plates - front finger guard - hydraulically acting sheet metal hold-down device - 1x freely movable foot switch - emergency stop button at the front - movable scrap switch - original operating instructions + circuit diagram Special accessories included: - EHT pneumatic sheet metal holding device for thin sheet metal cuts - 1x EHT extra long side stop 3.000 mm with mm scale & support foot - 1x EHT extra long support arm with 3.000 mm with scale & Support foot - EHT additional support arms with mm scale

Year of construction: 1987, condition: used, fabric-no. 202 395 working length 2550 mm output 2000 KN Gedpfxjq Awh Rs Ah Ejbw tracking travel 13 mm safety distance 176 mm

Condition: excellent (used), functionality: fully functional, Year of construction: 1994, EHT hydraulic guillotine shear type TSS 3-40, working width 4100 mm, max. sheet thickness 3.0 mm, pneumatic sheet support device, NC controlled backgauge, support arms, extra set of blades. Gedpfsw Uf Nrex Ah Ejbw

Year of construction: 1987, condition: ready for operation (used), An EHT hydraulic guillotine shear refurbished in 2023 is available. Cutting length: 3000mm, max. sheet thickness steel/VA: 4mm/2mm, backgauge: 10mm-1000mm, adjustment speed: 180mm/s, stroke rate: 18-31 strokes/min, oil volume: 160l. Machine dimensions X/Y/Z: approx. 3700mm/2100mm/2150mm, weight: approx. 4800kg, operating hours: 44024h. The cylinders, blades and hoses were overhauled in 2023. On-site inspection is possible. Gbedjwrhwuspfx Ah Eew

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1997, operating hours: 4,125 h, working width: 3,050 mm, sheet thickness (max.): 13 mm, back gauge: 1,000 mm, TECHNICAL DETAILS Sheet width: 3,050 mm Sheet thickness: 13 mm Back gauge – electric: 10–1,000 mm Strokes: 16 strokes/min Control: Elgo Gbjdjww E Nxepfx Ah Esw MACHINE DETAILS Total power requirement: 22 kW Operating hours: approx. 4,124 h EQUIPMENT - Automatic cutting gap adjustment - Sheet lifting device - Foot switch - Digital back gauge 1,000 Elgo - Scrap chute - Rear safety guards - Angle stop - Material support arms

Condition: excellent (used), Year of construction: 2001, sheet thickness steel (max.): 6 mm, cutting length (max.): 3,050 mm, Equipment: finger protection, Hydraulic guillotine shear Manufacturer EHT Type. TSS 6-30 Year of manufacture 2001 Technical data Make: EHT Type: TSS 6 - 30 Year of manufacture: 2001 Usable length: 3050 mm Sheet thickness: 6 mm Motor: 11 kW Oil quantity 250 L Dimensions: L 3.70 x W 2.15 (plus stop arms 1m, plus grid 0.6m) x H 2.15 m Weight: approx. 8 t Equipment • Angle stop • 3 support arms • Controlled rear stop 10-1000mm • Control Elgo P8721 • Pneumatic holding device with scrap chute • Cutting edge lighting • Rear area protection via light barrier • Cutting length adjustment Gbedpfx Ahovkd Eto Eew All information without guarantee. A demonstration is possible at any time in our exhibition hall.

Condition: used, Year of construction: 2000, pressure 85.0 t chamfer lenght 2050 mm distance between columns 1650 mm column arm 400 mm stroke 240 mm dayligth 320 - 560 mm ajustment speed 150 mm/sec Gbodpsxab Ugofx Ah Eow working feed 15.0 mm/sec return speed 150 mm/sec back stop - adjustable 5.0 - 1000 mm table width 110 mm work height max. 1050 mm operating pressure max. 297 bar compressed air 4.5 - 6.0 bar oil volume 200 l operating pressure 340 bar total power requirement 7.5 kW weight of the machine ca. 5900 kg range L-W-H 4100 x 2100 x 2750 mm with increased installation height / piston stroke well-maintained condition (!!) - in checked condition - machine video - ?v=ikl6RNZWeiU Equipment: - CNC electro-hydraulic press brake - including CYBELEC CNC control * swiveling control panel at the front right * external screen - CNC axis adjustment: Y1 - Y2 - X - R - Z1 - Z2 - I + CNC crowning - CNC electro-motorized back stop (X axis) * Travel range .. 5.0 - 1,000 mm * Travel speed .. 250 mm/sec. - CNC electro-motorized height adjustment of the back stop (R axis) * Travel range .. 70 - 235 mm * Travel speed .. 100 mm/sec. - CNC electro-motoric adjustment of the stop fingers (Z axes) * Travel range Z1 .. 405 - 1.565 mm * Travel speed .. 1.000 mm/sec. * Travel range Z2 .. 485 - 1.645 mm * Travel speed .. 1.000 mm/sec. - CNC electro-motoric table crowning - CNC pneumatic die displacement (I axis) - EHT pneumatic tool clamping - upper tool - EHT manual tool clamping - lower tool * Tool holder 90.0 mm + 13.0 mm possible - 1x freely movable 2-hand/foot control - 2x front, stable support arms including "sliding system" - side protective device (swinging doors) - rear protective device (swinging door) - original operating instructions + circuit diagram etc. * Special accessories included: - Oil cooler for use in continuous operation

Year of construction: 1998, condition: good (used), functionality: fully functional, machine/vehicle number: 107856, new seals on hydraulic cylinders Gbodpfx Ahjl N Ufyj Ejw TECHNICAL DETAILS material length: 6050 mm sheet thickness: 6 mm (450 N/qmm) passage: 6050 mm upright projection: 100 mm Control system: ELGO P8721 number of support arms: 4 stop range (from cutting line): 10 - 1000 mm Adjustment speed: 70 mm/s MACHINE DETAILS machine length: 7000 mm machine width (without support arms): 2350 mm machine width with supporting arms: 3440 mm machine height: 2550 mm Machine weight: 21000 kg Oil tank. 300 l Connected load: 18 kW Material: aluminum 1,2 mm EQUIPMENT motorized backgauge 1 side stop sheet holding-up system

Condition: good (used), Year of construction: 1999, cutting width: 6.050 mm cutting thickness: max. 4 mm length stop range: 10 - 1.000 mm Gbodpfxswzvnte Ah Eew

Year of construction: 1995, condition: ready for operation (used), Pressing force: 200t/2000kN, bending length: 3550mm, upright distance: 3050mm, upright projection: 350mm, max. ram stroke: 200mm, max. ram-to-table distance: 540mm. Dimensions X/Y/Z: approx. 4400mm/2100mm/3200mm, weight: approx. 16000kg, control: Cybelec DNC 800. Including a matrix, 2x upper tool (30°/60°) and a new light barrier. Documentation available. On-site inspection is possible. Gedpfx Aotva Dnjh Ejbw

Condition: good (used), functionality: fully functional, Year of construction: 2003, Pressure: 225 t Bending length: 2050 mm Distance between uprights: 1550 mm Control: CYBELEC DNC 1200 PS Eco Stroke: 550 mm Table height: 700 mm Throat depth: 405 mm Distance table/ram: 320-870 mm Frame throat depth: 405 mm Machine weight approx.: 14,000 kg Accessories/Equipment: - Controlled axes: Y1 - Y2 - X - R - Z1 and Z2 manually adjustable - Lasersafe angle measurement - Pneumatically adjustable support table - Pneumatic upper and lower tool clamping Gbodpfx Aewvi Uvoh Esw - Two-hand foot pedal operation - Manual crowning

Condition: not inspected (used), Year of construction: 1992, Plate shears make: EHT, type: TSS 4 - 40, SN: 105129, year of manufacture: 1992, working range: 4,000 x 4 mm, digital display, Gjdpfx Ahjv Duico Eobw Note: Machine already professionally dismantled and ready for transport

Condition: used, Year of construction: 1998, pressure 175 t chamfer lenght 4050 mm distance between columns 3050 mm throat 300 mm stroke 240 mm stroke speed - idle stroke downwards max. 140 mm/sec working feed max. 9 mm/sec stroke speed -return max. 130 mm/sec distance between table / ram min. 370 - max. 610 mm control CYBELEC DNC 880S total power requirement 15 kW weight of the machine ca. 15 t dimensions of the machine ca. 5,89 x 3,6 x 3,16 m Features: - Controlled axes: Y1, Y2, X, R - CNC crowning - CYBELEC DNC 880S control - Swivel control, front right - 4x manually adjustable stop fingers - Foot switch - 1 set of upper tools - 1 set of lower tools - 2x material support arms at the front - Side + rear protective device - Operating instructions Gedpfxetv Rh Aj Ah Eobw

Condition: used, functionality: fully functional, Year of construction: 1981, control type: PLC-controlled, Guillotine Shear Manufacturer: EHS Model: 13-31 Year of Manufacture: 1981 Factory No.: 18443 Technical Data: Max. Shearing Capacity: 13 mm up to 440 N/mm² Max. Cutting Width: 3050 mm Blade Length: 3100 mm Clear Pass-Through: 3070 mm Godpfx Aoxu D Rmoh Esbw Adjustable Back Gauge: 10–1000 mm Adjustable Cutting Angle: 1° – 4° Equivalent Shearing Capacity: 2–13 mm Max. Pressure in Hydraulic System: 300 bar Pressure in Hold-Down System: 80 bar Pressure in Return System: 130 bar Nitrogen Precharge in Hydraulic Accumulator: 100 bar Oil Tank Capacity: 300 liters Operating Voltage, Three-phase: 380 V, 50 Hz Control Voltage: 220 V Total Connected Load: 16 kW Total Rated Current: 32 A Rated Current for Main Fuse: 50 A Total Weight: 7800 kg

Condition: good (used), functionality: fully functional, Year of construction: 1995, Pressure: 300 t Bending length: 4050 mm Distance between columns: 3550 mm Oil capacity: 400 l Control: MOD EVA 19T Total power requirement: 22 kW Machine weight approx.: 20,000 kg Equipment: Gbjdpfsxu I Uvsx Ah Eow - CNC control Cybelec ModEva 19 T - 2 bending aids - Die shifting - Pneumatic tool clamping (top and bottom) - Crowning system - Controlled axes: y1, y2, x, R, z1, z2 - Two-hand and foot control - 2 parking stations for bending aid

Condition: good (used), Year of construction: 2000, Punching press Manufacturer: EHT Model: Strippit 1500/30 Year of manufacture: 2000 CNC control: Fanuc Working area without repositioning: 2500 x 1500 mm Max. material thickness: 8 mm Punching force: 30 t Turret with 46 tool stations, including 4 index stations size D 3 programmable clamps Metal table Used exclusively in single-shift operation Gedpfx Aeul S Eaeh Ejbw Including WILSON TOOL tools

Condition: ready for operation (used), Year of construction: 1964, working width: 3,050 mm, sheet thickness (max.): 10 mm, total length: 4,250 mm, total width: 2,800 mm, total height: 1,800 mm, Working width: 3050 mm Sheet thickness: 10 mm Gbodpfx Aoxrculjh Ejw Equipped with infeed table 2500x2000 mm

Condition: used, Year of construction: 2008, sheet width 3050 mm plate thickness 6 mm rear stop 10-1000 mm cutting angle 0,5 - 2,5 ° down holder 20 Stk no. of strokes 14 - 23 Hub/min work height max. 900 mm oil volume 140 l total power requirement 11 kW dimensions of the machine ca. 4000 x 2150 x 1900 mm weight 7200 kg Equipment: - ELGO control type P9724 - Automatic cutting angle adjustment Godpfx Ahov Rgyge Ejbw - Automatic cutting gap adjustment - Electric backgauge - Pneumatic sheet metal hold-up device - Light barrier behind the machine - 4 support arms - Front finger guard - Foot switch - Operating instructions

Condition: used, functionality: fully functional, control type: PLC-controlled, Hydraulic guillotine shear Manufacturer: EHT Model: EHS 13 - 31 Gbedsxu Dyuepfx Ah Ejw Cutting length: 3100 mm Material thickness: 13 mm Backgauge

Condition: good (used), functionality: fully functional, Year of construction: 2008, Press force: 170 t Bending length: 4050 mm Machine weight approx.: 16,300 kg Control: ModEva 10S Equipment: Gbodpfx Asxu I Ucjh Eew - CNC control Cybelec ModEva 10S - Lasersafe - 2 sheet supports - Die shifting - Crowning system - Pneumatic tool clamping (top and bottom) - Controlled axes: y1, y2, x, R, z1, z2 - Tool cabinet with tools

Condition: good (used), Year of construction: 1990, Pressure 320 t folding length 8050 mm Godpfx Aohwib Tsh Ejbw column width 7550 mm Control Cybelec ModEva 12S Equipment/accessories: - CNC-controlled backgauge x-direction and R-direction - motorized die shift M1 and M2 - 2 x pneumatic bending aids in front - pneumatic sheet holding unit - automatic die clamping at the top - motorized crowning rebuild 2009: - motorized die shift 111-112 mechanical and electrical NEW - backgauge X-R mechanical and electrical NEW - Punch clamping automatic mechanical and electrical NEW - CNC control mechanical and electrical NEW - Safety valves NEW - Measuring rulers NEW - Control valves Y1 - Y2 NEW - Main pump hydraulics NEW

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1993, bending force (max.): 150 t, stroke length: 700 mm, throat depth: 350 mm, distance between stands: 3,050 mm, working length: 3,550 mm, The control system was retrofitted in 2011! TECHNICAL DETAILS Press force: 150 t Bending length: 3,550 mm Distance between uprights: 3,050 mm Stroke: 700 mm Throat depth: 350 mm MACHINE DETAILS Control: Cybelec DNC 880S Gbsdpfoxn Srxex Ah Eow Dimensions & Weight Dimensions (L x W x H): 4,400 × 2,200 × 3,940 mm Machine weight: approx. 15,000 kg EQUIPMENT Bending aid in front of the machine Parking space for bending aid 3 backgauge fingers