Used Eht Tss 4-31 for sale (52)

Condition: used, Year of construction: 1985, sheet width 3100 mm plate thickness 4.0 mm thickness at "Niro-steel" 2.5 mm cutting angle adjustment 1.0 ° back stop - adjustable 10 - 1000 mm adjustment speed 180 mm/s down holder 21 Stück strokes per minute 18 - 31 oil volume 160 L Control ELGO P8511 column arm 200 mm distance between columns 3050 mm 0 max. 300 bar voltage 400 V main drive 9.0 kW weight of the machine ca. 4800 kg. dimensions of the machine ca. 3660 x 2070 x 2140 mm from a maintenance workshop Equipment: - electro-hydraulic sheet metal shear "swing cut" - machine frame = all-steel welded construction - ELGO NC control model P8511, control panel at the front left * for positioning the electro-motoric rear stop Codpfoxab Tvjx Aktjri * target/actual position value input possible * adjustment by three-phase motor via toothed belt - support table with ball rollers * there are recessed grips between the table plates - front finger guard - hydraulically acting sheet metal hold-down device - 1x freely movable foot switch - emergency stop button at the front - movable scrap switch - original operating instructions + circuit diagram Special accessories included: - EHT pneumatic sheet metal holding device for thin sheet metal cuts - 1x EHT extra long side stop 3.000 mm with mm scale & support foot - 1x EHT extra long support arm with 3.000 mm with scale & Support foot - EHT additional support arms with mm scale

Year of construction: 1987, condition: ready for operation (used), An EHT hydraulic guillotine shear refurbished in 2023 is available. Cutting length: 3000mm, max. sheet thickness steel/VA: 4mm/2mm, backgauge: 10mm-1000mm, adjustment speed: 180mm/s, stroke rate: 18-31 strokes/min, oil volume: 160l. Machine dimensions X/Y/Z: approx. 3700mm/2100mm/2150mm, weight: approx. 4800kg, operating hours: 44024h. The cylinders, blades and hoses were overhauled in 2023. On-site inspection is possible. Crodpfjwrhwusx Aktji

Condition: good (used), Year of construction: 1999, cutting width: 6.050 mm cutting thickness: max. 4 mm Crjdpfjwzvntsx Aktei length stop range: 10 - 1.000 mm

Condition: good (used), Year of construction: 2000, sheet width 3100 mm plate thickness 4.0 mm thickness at "Niro-steel" 2.5 mm cutting angle adjustment 1.0 ° back stop - adjustable 10 - 1000 mm adjustment speed 180 mm/s down holder 21 Stück strokes per minute 18 - 31 column arm 200 mm Control ELGO P8721 oil volume 160 L 0 max. 300 bar Csdjzycpxepfx Aktsri voltage 400 V main drive 7.5 kW weight of the machine ca. 4800 kg. dimensions of the machine ca. 3660 x 2070 x 2140 mm from a maintenance workshop good condition (!!) Features: - Electro-hydraulic sheet metal shear ("swing cut") - Machine frame = all-steel welded construction - ELGO NC control system, Model P8721, control panel on the front left * for positioning the electrically driven backgauge * Target/actual position value input possible * Adjustment via three-phase motor using a toothed belt - Support table with ball bearings * Recessed handles between the table plates - Front finger guard - Hydraulic sheet metal hold-down devices - 1x side stop with mm scale - 2x front support arms with mm scale - 1x freely movable foot switch - Emergency stop button at the front - 1x movable / rear scrap deflector - Original operating instructions Special accessories included: - EHT pneumatic sheet metal holding device for thin sheet metal blanks

Condition: used, functionality: fully functional, Year of construction: 1987, machine/vehicle number: 101536, Offered for sale is a hydraulic guillotine shear Manufacturer: Eisen und Hammerschmidt GmbH Model: TSS4-20 Year of manufacture: 1987 Serial No.: 101536 Capacity: 4 mm Working width: 2,000 mm Control: ELGO Type P8511 Light curtain system by SICK Used, fully functional condition. Collection by purchaser; assistance with dismantling/transport can be arranged if required. — If you are interested or have any questions, please feel free to send me a message. Viewing on site by appointment possible. Further metalworking machinery such as bench drills, press brakes, column drilling machines, eccentric presses, heavy-duty racking, welding tables, MIG welders, compressors, etc. – please take a look at my other listings. Location for viewing and collection: 12277 Berlin Domestic price net plus VAT or Net export price Collection only – dismantling and transport by buyer or by arrangement. If you are interested or have any questions, please feel free to send me a message. Further photos and technical details available on request. Csdox Da D Uopfx Akteri All information is subject to change without notice. Errors and prior sale reserved. For further questions, please call Nous parlons Français / Мы говорим по-русски We speak English / Noi vorbim românește Viber / WhatsApp / Skype We handle all customs and registration matters for an additional charge. For an extra fee, we can transfer the vehicles to the port.

Condition: used, Year of construction: 1971, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Working area Sheet metal width: 2,000 mm Sheet metal thickness for St 42: 16 mm Passage width: 2,250 mm Overhang: 600 mm Knife and cutting Knife length: 2,005 mm Cutting gap adjustment: 0.05–0.95 mm Cutting angle: 1° 40′ Clamping beam: 10 pcs. Back gauge Gauge length: 1,000 mm Back gauge adjustment: 10–1,000 mm Work table Table size: 2,500 × 700 mm Table height above floor: 800 mm Credpoz S Ng Hefx Aktei Hydraulics and Electrics Oil volume: 900 l Operating voltage: 380 V Machine data Machine weight: approx. 10 t Space requirement: approx. 3 × 2.3 × 2.3 m EQUIPMENT Foot switch Supports Spare knife

Condition: good (used), functionality: fully functional, Year of construction: 1995, Press force: 150 t Bending length: 4050 mm Frame width: 3550 mm Control system: CYBELEC ModEva Pac Overhang: 350 mm Distance between table and ram: 430 mm Table width: 250 mm Stroke: 250 mm Total power requirement: 18.5 kW Machine weight, approx.: 16500 kg Space requirement, approx.: 4400x2100x3200 mm Equipment/accessories: - Control system upgrade at the end of 2018 - Electric back gauge, 1250 mm - 10-stage die shifting - Crowning - Tool holder EHT 26 mm - Axis control: Y1, Y2, X, R - Sheet metal support table - 4 manually adjustable stop fingers Cjdpfezd S Thox Aktjri - Pneumatic upper tool clamping - Safety light curtain - 3 adjustable support arms - Oil cooler - 2-hand foot switch

Condition: good (used), functionality: fully functional, Year of construction: 2001, operating hours: 7,300 h, stroke length: 400 mm, operating speed: 140 mm/s, reverse speed: 180 mm/s, oil tank capacity: 350 l, overall weight: 14,800 kg, total length: 6,350 mm, total width: 3,590 mm, total height: 3,220 mm, power: 18.5 kW (25.15 HP), input voltage: 400 V, pressing force: 175 t, clearance between the columns: 3,550 mm, distance table to ram: 720 mm, type of input current: three-phase, Equipment: CE marking, documentation/manual, safety light barrier, EHT VarioPress 175-40, approx. 7300 operating hours, original EHT tooling, straight bending tool 420 mm x 4000 mm, split, forming pad 220 mm x 4000 mm, split, 2 sets of dies, split, pneumatic tool clamping system, top and bottom, Csdpfo Aa Nz Sox Akteri automatic crowning, 2 x adjustable material support arms, table/punch distance, min.: 320 mm, table/punch distance, max.: 720 mm, 3 stop fingers, manually adjustable, 2 sets of upper tools, 1 x forming pad 220 mm, 1 x straight tool 420 mm, original operating manual and electrical diagrams available, annual maintenance and safety inspection carried out, last maintenance in 2025.

Condition: good (used), functionality: fully functional, Year of construction: 2007, operating hours: 94,201 h, control type: CNC control, bending force (max.): 400 t, installation height: 595 mm, Bending length [mm] 3550 Pressing force [tons] 400 Control system Cybelec ModEva 10s Standard equipment: - Sturdy machine frame as a welded construction in all-steel design - Press beam with high bending strength - Electro-hydraulic upper drive via proportional valves - Modern block hydraulics - CNC rear stop for X and R axes, safe displacement of the stop fingers from the front by means of a safety interlock - Upper tool clamping system "EHT", manual, head width 26mm, load max. 3000 kN/m - Lower tool clamping system EHT, manual, clamping width 90mm for block tools and 13mm for single V-dies, without clamping - Control system: CYBELEC ModEva 10S on Windows, 2D graphic control with a 10.4" color screen - Control cabinet air conditioning + Rear stop - System 1, 5 axes, straight finger, 140mm wide, adjustment of R axis 150mm + EHT quick clamping device, for upper tools, pneumatic, head width 26mm, load max. 3000 kN/m (self-centering horizontally) + EHT lower tool clamping, Crodpfx Aez Rmcvektji pneumatic, clamping width 55mm + Hardened insert strip, for EHT lower tool clamping 55mm / 90mm + Lower tool displacement, CNC-controlled, infinitely adjustable via rear stop 1 (max. 4550 mm working length) + Crowning device CNC-controlled, in the table without tool clamping, load max. 3000 kN/m + Safety device LaserSafe (up to max. upper tool height 440mm) + Additional foot switch + Bending aid 1st arm, load max. 1500N with 2 integrated support strips in standard design + Bending aid 2nd arm, load max. 1500N with 2 integrated support strips in standard design + 2 pcs. support strips for a bending aid with T-slot 14mm and scale and ball rollers + 2 pcs. table extension for bending aid + Short park position left + Short park position right

Condition: used, Year of construction: 1994, sheet width / mm plate thickness / mm distance between columns / mm Manufacturer: EHT Type: TSS 20-25 Year of construction: 1994 Max. Cutting length: 2250 mm Max. Sheet thickness: 20 mm Strip width min / max: 10/1000 mm Distance between the consoles: 2530 Height above the ground: 900 mm Table length without extension arms: 3030 mm Oil volume: 800 l Max. Pressure: 280 bar Operating voltage: 400V Control voltage: 230 V. Nominal current: 87 A. Weight: 15.8 to Dimensions L x W x H: 3500 x 2500 x 2400 mm Accessories / special equipment Pneumatic cutting gap adjustment Cutting length limitation Roller conveyor elevation bracket Hand protection 1 bay Csdpfx Ajuddh Ajktori Multitron control Multitron PS 80; ELCO 85 P Lower knife height adjustment

Condition: used, Year of construction: 1995, sheet width 6000 mm plate thickness 6 mm distance between columns 610 mm Control Elgo 87 P2 total power requirement 15 kW weight of the machine ca. 22 t The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Crsdpfoyutt Eex Aktei Your Markus Hirsch Team

Condition: ready for operation (used), Year of construction: 1999, sheet width 3200 mm plate thickness 4.0 mm ST distance between columns 3300 mm upper clamping bar adjustment 400 mm Adjustment folding beam 80.0 mm pivoting angle 180 Grad clamping capacity max. 200 KN rear stop 10.0 - 1600 mm oil volume 160 Liter total power requirement 9.8 kW weight 8500 kg range L-W-H ~ 4900 x 2000 x 2300 mm from a maintenance workshop good / well-maintained condition (!!) - inspected condition - machine video - ?v=RY-amZooeX4 Equipment: - robust CNC folding machine - CNC control unit - CYBELEC "DNC 80 PP" * swiveling control panel, front right * 2D graphic display for visualization and multi-simulation * 2D graphic programming * easy operation - CNC motorized backgauge * travel range 10.0 - 1,600 mm * pneumatic / retractable gauge fingers * adjustment speed max. 250 mm/sec. * rear sheet support table with brushes - motorized lower beam adjustment (S-axis) - electro-hydraulic folding movement of the lower beam Cedpfoxaa A Nex Akteri - pneumatic upper tool clamping - pneumatic lower tool clamping - 1x mobile dual foot pedal - original operating manual + electrical/hydraulic schematics Special accessories included: - 1x segmented set of goat-foot upper tools, H = 150 mm - 1x segmented set of goat-foot upper tools, H = 200 mm - 1x standard sharp-nosed rail (installed) - 1x segmented set of bending/lower tools (installed) - rear sheet support with brushes

Condition: used, functionality: fully functional, Year of construction: 1992, power: 2,500 kW (3,399.05 HP), input voltage: 380 V, input current: 53 A, input frequency: 50 Hz, pressing force: 250 t, table length: 4,050 mm, type of input current: three-phase, year of last overhaul: 2007, Equipment: documentation/manual, We are offering this used Eisen u. Hammerwerk GmbH - EHT EHPS 25-40 press brake (hydraulic press brake, die bending press) for sale. Available immediately. Ready for operation. For sale due to new acquisition. Crodpfjy D Sy Rex Aktsi Specifications: - 250 t pressing force - Cybelec DNC880S CNC control with Windows operating system (retrofitted in 2007) - Foot pedal control - Various upper tools in different lengths (segmented) - Lower tool (reversible die) in various lengths (segmented) - Hydraulic tool clamping - Support table for bent parts Technical data: - Machine type: EHPS 25-40 - Force: 2500 kN - Year of manufacture: 1992 - Working length: 4050 mm - Serial number: 207380 - Power supply: 3~ - Frequency: 50 Hz - Operating voltage: 380 V - Control voltage: 24/220 V - Rated current: 53 A - Main fuse rated current: 80 A - Circuit diagram number: 209-178/372 If you have any questions or require more information, feel free to send us a message or give us a call. Machine location at our premises: Pavic Fahrzeugtechnik Homberg GmbH Poschweg 2 34576 Homberg Relbehausen Germany This is a non-binding offer. Subject to prior sale, errors and changes excepted.

Condition: good (used), functionality: fully functional, Year of construction: 1999, Press force: 225 t Bending length: 4050 mm Frame width: 3550 mm Control system: CYBELEC DNC 86 PS Cjdpszd Sqyjfx Aktjri Total power consumption: 18.5 kW Machine weight (approx.): 18,000 kg Space requirement (approx.): 5180x2400x3200 mm Equipment: - CNC control system Cybelec - Pneumatic upper and lower tool clamping - Die shifting - Light curtain on the machine - 2 support arms in front of the machine - Controlled axes y1, y2, x, r, z1, z2 - Compensation - 2-hand foot control - Side protective doors

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2009, controller model: Cybelec ModEva 10S, bending force (max.): 170 t, empty load weight: 16,300 kg, working length: 4,050 mm, TECHNICAL DETAILS Press force: 170 t Bending length: 4,050 mm MACHINE DETAILS Control: Cybelec ModEva 10S Machine weight: 16,300 kg EQUIPMENT Lasersafe Credpfxjxwnv Ee Aktoi 2 sheet supports Die shifting Crowning Pneumatic tool clamping top and bottom Controlled axes: Y1, Y2, X, R, Z1, Z2 Tool cabinet with tools

Condition: good (used), Year of construction: 1992, Sheet metal shears, tin scissors, sheet metal scissors, hydraulic shears -Sheet shear: hydraulic -Cutting width: 2000 mm -Max. cutting thickness: steel 6 mm -Features: Back gauge, cutting gap adjustment -Space requirement: 3280/2700/H2060 mm Codpfx Akoywzbdstsri -Transport dimensions: 2280/2700/H2060 mm -Weight: 5980 kg

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1995, controller model: Cybelec ModEva 19 T, bending force (max.): 300 t, distance between stands: 3,550 mm, oil tank capacity: 400 l, working length: 4,050 mm, The machine control was renewed in 2022! TECHNICAL DETAILS Press force: 300 t Bending length: 4,050 mm Distance between uprights: 3,550 mm Oil capacity: 400 l MACHINE DETAILS Control system: Cybelec ModEva 19 T Total power requirement: 22 kW Machine weight: approx. 20,000 kg EQUIPMENT 2 bending aids Matrix displacement Pneumatic tool clamping, top and bottom Crowning Controlled axes: y1, y2, x, R, z1, z2 Two-hand foot control 2 parking stations for bending aid Crjdjxwnqcspfx Aktsi

Condition: used, Year of construction: 1986, machine/vehicle number: 200485, Lg.no. 24243 Technical data: - max. working length 4050 mm - upright clearance 3050 mm - max. pressing force 110 t - ram stroke 200 mm - throat 350 mm - Table height 900 mm - Opening width 400 mm - Drive power 17.5 kW - Space requirement approx. W 4250 x H 2850 x D 2200 mm - Weight approx. 15.0 t - with: Crodetqmvzopfx Aktji - CYBELEC ModEva 10 S control unit renewed in 2011 - Y 1+ 2 , X , Z - Two-hand control panel: - Mot. backgauge 5 - 1000 mm - front support arms - split pointing tool, - universal die

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1994, working width: 4,050 mm, sheet thickness (max.): 8 mm, TECHNICAL DETAILS Sheet metal width: 4,050 mm Sheet metal thickness: 8 mm Crjdpozapq Dsfx Aktsi Control: conventional

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1998, controller model: CYBELEC DNC 880S, bending force (max.): 175 t, stroke length: 240 mm, throat depth: 300 mm, distance between stands: 3,050 mm, TECHNICAL DETAILS Pressing force: 175 t Bending length: 4,050 mm Distance between uprights: 3,050 mm Throat depth: 300 mm Stroke: 240 mm Stroke speed (down, unloaded) max.: 140 mm/s Working speed max.: 9 mm/s Stroke speed (return) max.: 130 mm/s Distance table/punch min.: 370 mm Distance table/punch max.: 610 mm MACHINE DETAILS Control: CYBELEC DNC 880S Total power requirement: 15 kW Controlled axes: Y1, Y2, X, R Dimensions & Weight Space requirement: approx. 5.89 x 3.6 x 3.16 m Machine weight: approx. 15 t EQUIPMENT CNC crowning Csdpfx Akeygw Ahstori 4x backgauge fingers (manually adjustable) Foot switch 1 set of upper tooling 1 set of lower tooling 2x front sheet supports Side and rear safety guards Operating manual

Condition: good (used), Year of construction: 2000, Punch press Manufacturer: EHT Type: Strippit 1500/30 Year of manufacture: 2000 CNC control: Fanuc Working area without repositioning: 2500 x 1500 mm Maximum material thickness: 8 mm Punching force: 30 tons Turret with 46 tool stations, including 4 indexing stations, size D 3 programmable clamps Metal table Used exclusively in single-shift operation Includes tools from WILSON TOOL 31126 Cjdpfoul S Eajx Aktjri

Condition: good (used), Year of construction: 2006, Press force: 135 t Bending length: 2550 mm Frame gap: 2050 mm Control system: CYBELEC ModEva 10 S Total power requirement: 25 kW Machine weight approx.: 11,000 kg Description Machine: – Rigid machine frame as an all-steel welded construction Crsdpfx Asy H Ilbjktei – Ram with high flexural rigidity – Electrohydraulic top drive via proportional valves – Modern block hydraulics Special equipment: – Increased installation height and stroke by 150 mm each – Rear gauge system 2 – 2 axes, R axis adjustment 150 mm – 2 x additional backgauge fingers 2/4 axes, however offset by 20 mm – CNC sheet support device – Distance from bending line to sheet support device approx. 240 mm – EHT quick-release clamping system for EHT upper tools, pneumatic, head width 26 mm, horizontally self-centering – EHT lower tool clamping, receiving width 55 mm, pneumatic – Hardened insert strip for EHT lower tool clamping 55 mm / 90 mm – CNC-controlled die shifting, stepless – CNC crowning system in the table (minimum table width 110 mm), without tool clamping – Safety device SICK V4000 – 2 x bending aids max. 1500 N – 2 x 2 support rails for bending aid with 14 mm T-slot and scale – 2 x table extensions for bending aid – Park position right and left, short

Condition: used, Year of construction: 2006, pressure 135 t chamfer lenght 2550 mm distance between columns 2050 mm control CYBELEC ModEva 10 S dayligth 570 (EHT) mm total power requirement 25 kW weight of the machine ca. 11.000 kg Machine: - Sturdy machine frame constructed as a fully welded all-steel structure - Pressure beam with high bending strength - Electrohydraulic top drive via proportional valves - Modern block hydraulic system Optional equipment: - Increase in installation height and stroke by 150 mm each - Backgauge system 2 - 2 axes, R-axis adjustment 150 mm - 2 x additional stop fingers 2/4-axes, however, offset by 20 mm - CNC holding device - Distance from the bending line to the holding device approx. 240 mm - EHT quick-clamping device for EHT upper tools, pneumatic, head width 26 mm, horizontally self-centering - EHT lower tool clamping, mounting width 55 mm, pneumatic - Hardened insert strip for EHT lower tool clamping 55 mm / 90 mm - Die shift CNC-controlled, infinitely variable - CNC crowning device in the table (table width min. 110 mm) without tool clamping - SICK V4000 safety device - 2 x bending aids, max. 1500 N - 2 x 2 support rails for bending aid with 14 mm T-slot and scale - 2 x table extensions for bending aid - Parking position on right and left, short Crodpfx Aksy D T S Iotoi

Year of construction: 1998, condition: good (used), functionality: fully functional, machine/vehicle number: 107856, new seals on hydraulic cylinders TECHNICAL DETAILS material length: 6050 mm sheet thickness: 6 mm (450 N/qmm) passage: 6050 mm upright projection: 100 mm Control system: ELGO P8721 number of support arms: 4 stop range (from cutting line): 10 - 1000 mm Adjustment speed: 70 mm/s Cjdpfsl N Ufyjx Aktjri MACHINE DETAILS machine length: 7000 mm machine width (without support arms): 2350 mm machine width with supporting arms: 3440 mm machine height: 2550 mm Machine weight: 21000 kg Oil tank. 300 l Connected load: 18 kW Material: aluminum 1,2 mm EQUIPMENT motorized backgauge 1 side stop sheet holding-up system

Condition: excellent (used), functionality: fully functional, Year of construction: 1995, CNC Hydraulic Press Brake Manufacturer: EHT Model: EHPS 2030 Year of manufacture: 1995 Control system: Cybelec Max. working width: 3050 mm Clamping force: 200 tons Main motor: 18.5 kW Back gauge: 1000 mm Bending aid 2 Multi V dies Csdpfo Ahm Ibox Aktjri 2 sets of split tools, 260 mm high Hydraulic crowning in the table