Used Gripper for sale (710)

Condition: used, Year of construction: 2019, Control Unit: R-30 iB Plus This robot was used as part of a complete automation system for loading and unloading in a machining line • Axes: 6 • Maximum payload (wrist): 165 kg • Reach: 2655 mm • Repeatability: ± 0.05 mm (ISO 9283) • Mechanical weight: approx. 1090 kg • Joint motion ranges: J1: ± 370° J2: ± 136° J3: ± 312° J4: ± 720° J5: ± 250° J6: ± 720° • Maximum axis speeds: J1: ~130°/s J2: ~115°/s J3: ~125°/s J4: ~180°/s J5: ~180°/s J6: ~260°/s Machine/asset does not include any product-related tool/fixture or gripper (robot). Podsxgqg Ejpfx Adyjgu

Condition: used, Year of construction: 2012, functionality: fully functional, The plant comprises the following components:  Platform with a vibrated base for the bin support; this platform is protected by perimeter railings and is accessed via a ship-type ladder;  Empty bag magazine; the supply of empty bags is performed manually by the operator. The exact position of the bags is secured by adjustable side guides; a sensor located under the stack of bags signals when the pile is depleted;  On the structure of the empty bag magazine, pneumatic cylinders are installed for gripping the bag, opening its mouth, and inserting it onto the product dosing spout. The bags are handled by a series of suction cups. The pneumatic control panel QP1 is also mounted on the supporting structure of the magazine;  The dosing spout is supported by 3 load cells; at the outlet, a bucket-type gate valve driven by two pneumatic cylinders is installed. Next to it, two additional cylinders with hooks at the ends are used for tensioning the bag mouth.  The bag is clamped along its longer side by two jaws that hold it after filling and guide it to the sewing machine. Movement is achieved by geared motor units and wheels sliding on chrome-plated rods. At this stage, the bag rests on a motorized conveyor belt for transfer; this belt is also raised via a pneumatic cylinder so that the bag rests gently upon filling completion; the height of this belt can be adjusted manually using a handwheel acting on four jacks, to adapt the belt height to the bag type.  Once inserted into the sewing machine, the bag is stitched and the thread cut; still resting on the conveyor, the bag reaches the overturning station—there, it is held by two jaws, rotated 90°, and finally released so as to be parallel to the conveyor.  The next belt features, in its initial part, a series of square rollers for bag straightening, followed by a conveyor belt for forward movement;  Lastly, there is the roller conveyor where the bag is picked up by the robot; this conveyor is stopped by a photocell when the bag reaches the end of the roller line;  The robot gripper is of the comb type and is equipped with a translation cylinder to discharge the bag and two cylinders operating a plate to lock the bag during handling prior to discharge. Pedpfx Aexrcc Ajdyogu  Two boxes containing the solenoid valves and vacuum units are installed on the plant;  An electrical control panel manages the entire plant; the operator panel and weighing module are installed on it;  The robot is managed by its own control panel with a dedicated operator interface;

Condition: used, mileage: 100 km, first registration: 01/2023, overall weight: 26,000 kg, axle configuration: 3 axles, emission class: euro6, loading space width: 2,400 mm, loading space length: 4,200 mm, Equipment: crane, Int. No.: 2014 Roll-off crane trough Dimensions L=4.2m x W=2.40m Year of manufacture 2014 Crane Atlas 92.2 3x hydraulic extension support Gripper High-level control Pendulum steel side walls Definable!!! * net 29,900 ¤ Pgodpfxjt D Sx Rs Adyju Trade-in possible Financing from 4.99% Subject to errors and prior sale! The information in this ad is a non-binding description and does not serve as a guaranteed feature. The seller assumes no liability for typing and data transmission errors. The equipment listed must be checked separately. All information in the ad is non-binding! Delivery throughout Germany on request Opening times: Monday to Thursday from 9:00 a.m. to 5:00 p.m. Friday from 9:00 a.m. to 2:00 p.m. and by appointment!!!

Condition: used, Year of construction: 1982, machine/vehicle number: 105981, Press capacity: 45 ton Ram stroke adjustable: 20 - 80 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 300 mm Free frontal opening L-R: 710 mm Table surface area : 700 x 450 mm Slide area: 700 x 360 mm Hole in table: 600 x 100 mm Number of strokes: 80 - 400 s.p.m. Required power: 10 kW Podpfx Adsuqc Ngeyogu Height over floor approx.: 2900 mm Weight of machine approx.: 7,2 ton Control: Siemens S7 Standard configuration With gripper feedMachine was completely overhauled in 2001 with SIEMENS S7 control.

Condition: good (used), Year of construction: 2012, load capacity: 235 kg, arm reach: 2,550 mm, The IRB 6640 serie is ABB Robotics latest generation of high payload, high performance industrial robots. With a focus on high production capacity, compact design and low weight, simple service and low maintenance cost. The IRB 6640 is ideal for process applications, regardless of industry. Typical areas are for example Spot Welding, Material Handling and Machine Tending. Year: 2012 (Multiple options available) Cabinet: IRC5 Teach Pendant: Included Signalling & Power Cables: Included (15m) Gripper: NOT included Please contact us for a quote and also the refurbishment options. As PLC Merkezi EOOD, we have more than 300 robots in our inventory and deal with the brand of KUKA, ABB, FANUC and Motoman. Pjdpfx Ajqz Txqjdyogu (Source: ABB's Website)

Year of construction: 2025, condition: new, functionality: fully functional, Semi-automatic depaneling / basic machine with parallel shuttle The dynamic depaneling machine LOW 4322 is especially suited for medium to high product volumes and meets growing demands in the production process. Printed circuit board blanks of various materials are separated using low-dust and low-stress sawing and milling techniques with maximum product flexibility, precision and throughput. Highly dynamic linear motor axes, tools and grippers meet the highest quality standards and guarantee the depaneling machine a long service life and high reliability. Pgsdpjw Et H Isfx Adysu Made in Germany Semiautomatic depaneling - solutions on demand The LOW 4322 depanelling system enables fast product changeover while maintaining short depanelling and handling times. The insertion of the blank PCB is done with a parallel shuttle, pick-up and fixation with pin clamping technology and if necessary in combination with vacuum suction cups. This machine is equipped with: • a shank and disc tool separating module on Z-axis (automatically rotatable 0-90) • X-Y cross stitch module in linear motor technology with high resolution measuring system • 2-compartment loading module built as parallel shuttle, separated left and right with sliding doors • Steel welded frame with two maintenance doors - left and right. Powder coated RAL 9002 • Standard vision system base module for teach-in programming (camera area 400 x 330 mm) • Working area is 420 x 330 mm • Automatic cutter length processing (only in combination with shank separation module) • Remote maintenance/support via remote connection (TeamViewer) or provided by the customer • Touch IPC with Windows 10 operating system • Laser axis measurement incl. protocol • air ionization • Cutter breakage control for end mills only • Preparation for vacuum clamping technology • Powder coated RAL 9002, ESD window and sliding doors Optionally a vacuum cleaner unit can be offered later.

Condition: excellent (used), Year of construction: 2011, Ficep 1003 DZB CNC Drilling / Sawing Line – Year 2011. 3 Spindles. Automatic Tool Changer. Scribing. Short Piece Removal. Pgodpfx Asxmvnusdyeu Hard Stamping. Gripper feed. Infeed and Outfeed Cross Transfers. 1000mm Section Capacity.

Condition: used, Year of construction: 2015, functionality: fully functional, machine/vehicle number: 346-09, This machine is equipped with a 2m LNS bar feeder, allowing it to fully automate the production of milled and turned parts directly from the bar stock. On the main spindle, there is an E162 power chuck with a bar capacity of Ø10mm. The bar feeder itself is designed for material up to Ø65mm. Additionally, the machine is fitted with a pneumatically operated two-jaw chuck to allow complete secondary machining of components on the back side. Finished parts can then be removed by an integrated gripper and placed onto the conveyor belt. The machine was retrofitted by CHIRON specifically for precious metal machining. This mainly means that seals within the machine have been reinforced, and the standard chip conveyor was replaced by a drawer unit with a fabric filter. Other features: - High-speed spindle with HSK 40 interface and high-pressure coolant (max. 40,000 rpm and up to 80 bar) - Oil cooler and chip filtration system - Kraft und Bauer fire suppression system with optical sensor Psdpsw U Tbcjfx Adyogu - Oil extraction system - Renishaw probe - Integrated tool breakage control/measurement - Tool changer with 64 positions Location: Medical device manufacturer >>>> Collets and tool holders are included in the sale and are part of the listed price.

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Pgodou Tg I Depfx Adysu Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: good (used), Year of construction: 2015, workpiece weight (max.): 40 kg, CABO Mixspace Multispeed Paint Mixer Gyroscopic Mixer (gyromixer) Year of manufacture: 2015 Display Alphanumeric 20 x 4 Pgedpovmtw Rjfx Adyju Maximum bucket weight 40 kg Bucket holder tray Pull-out Bucket gripper Automatic Gyroscopic ratio 1:1.8 Speed ​​settings 3 programmable Mixing speed 80 - 180 rpm Acceleration / deceleration during the mixing cycle Automatic speed adjustment to the bucket height Mixing cycle time 20sec - 30m Maximum bucket diameter 380 mm Bucket height: min - max 90 - 490 mm Bucket height 340 (+30) mm Bucket types Round/Square/Oval Mains voltage: 230v 50Hz 3A Machine weight 190 kg machine dimensions: width:860mm length:850mm height:1150mm

Year of construction: 2023, condition: used, Case maker Kolbus DA 370 Year: 2023 New generation of casemaker for faster production and shorter make-ready times. Automatic production of book cases, files, display cards, calendar backs or game boards, at rates of up to 65 cycles/min. Maximum production and process reliability in the manufacture of book cases. The DA 370 casemaker is a versatile machine for a wide range of applications. The machine with its non-stop case feeder is engineered to be ergonomic and extremely operator-friendly so that it can be easily operated by one person. Configuration: - Copilot system with touchscreen - sectional touch panel for direct operation - large display for showing the speed and malfunction messages - board prestacking conveyor to automatically reload the magazines (stream cover and stack feeder) - counter-stacker delivery with roller conveyor delivery incl. table - cloth feeder for non-stop operation with stack magazine - missing product check during separation of cloth and cardboard - cloth cylinder with grippers and interchangeable plates for rubber pads (5 plates 500 mm wide and 5 plates 720 mm wide, incl. 10 rubber pads) - cardboard centre strip magazine - device used to prepare centre strip roll - centre strip waste chopper - centre strip rub-down unit (head and foot) - rub-down unit used to bond the covering material to cardboards and spine strip without creases - extendable gluing station for processing hot glue with glue preparation in the premelter, heated glue roller and scraper roller - viscosity control unit for an automatic supply of water via a water container with a pump - device for padded cases - function used to request individual cases for monitoring purposes on the operating side - servo-controlled drive technology based on Siemens technology Special equipment: Pjdpsv N Ep Dsfx Adysgu - device for producing quarter-bound cases in two operating steps - device for small format - device fo large format - Remote Service Gateway Technical specifications: - Mechanical speed: up to 65 cycles/min - Open cover size max.: 205 x 670 mm - Joint width: 4 - 15 mm - Spine width: 14 - 120 mm - Turn in width open: up to 19 mm - Cloth width: 223 - 708 mm - Cloth height: 158 - 428 mm - Board thickness: 1 - 4 mm - Board width: 95 - 328 mm - Board height: 140 - 390 mm - Board centre strip thickness: 1 - 4 mm - Board centre strip width: 6 - 90 mm - Centre strip roll thickness: 0,3 - 0,6 mm - Centre strip roll width: 6 - 90 mm - Lining width: 195 - 670 mm - Lining height: 130 - 390 mm

Condition: used, Year of construction: 1977, Bobst Autoplatine SP 1420 E - 600 T (1977) Year of manufacture: 1977 Speed: 5,000 sheets/hour Counter: 5 million Size: max. 1420 x 1020 mm min. 700 x 500 mm Equipped with: • New gripper bar • New chains Available: immediately Location: Germany Pedpfx Adsxfu Drsyegu

Condition: excellent (used), Year of construction: 2018, 2018 KALTENBACH KDP1036 CNC DRILLING / MILLING / SCRIBING LINE – KBS 1051 SAWING LINE. INFEED CROSS TRANSFERS T13 20.5 METRES INFEED CAPACITY. GRIPPER FED MATERIAL MEASUREMENT KDP1036 3 AXIS. AUTOMATIC TOOL CHANGER. 500MM SUB AXIS FOR MILLING, DRILLING, MARKING & TAPPING. INTEGRATED CHIP CONVEYOR KBS 1051 SAW HORIZONTAL AND VERTICAL CLAMPING AUTOMATIC FEED CONTROL Automatic adjustment of saw band angle Pedpfxsxmvm Rj Adyogu LS 270 MEASURING HEAD OUTFEED 19.750mm OUTFEED CROSS TRANSFERS T13

Condition: excellent (used), Year of construction: 2022, Selco WNT 630 Beamsaw working size 3800x2200 with back lift table Technical specifications: Max cutting lenght: 3800 mm, Saw blade projection: 108 mm, Max gripper opening: 100 mm, Pgjdpfxev T Sdie Adyju Min panel size: 1830 x 915 mm, Max panel size: 3660 x 2200 mm, Max packet hight: 630 mm, Min. thickness on lift table: 10 mm, Lift table max lift: 985 mm, Lift table capacity: 5 t Back loading table or side loading oppening for panels 3800 x 2200 mm

Condition: used, Year of construction: 2011, Technical details: standard turning dia.: 200 turning length: max. 810 mm control: MSX-701 MAPPS IV greates pass round over bed: 800 mm Max. distance between centres: 1130 mm max. turning diameter: 320 mm max. workpiecediameter: 300 mm bar material dia.: 65 mm Traverse X-Axis 1: 210 Traverse X-Axis 2: 210 mm Traverse X-Axis 3: 210 mm Traverse Y-Axis 1: 110 (+65/-45) mm Traverse Y-Axis 2: 110 (+45,/-65) mm Traverse Z-Axis 1: 300 mm Traverse Z-Axis 3: 300 mm Traverse Z-Axis 2: 810 mm Traverse B-Axis: 870 mm turning speed range - spindle: 5.000 1/min Number of spindle speed ranges: 2 . spindle nose: JIS A2-6 spindle bore: 73 mm spindle bearing diameter: 120 mm C-Axis: 0,001 ° turning speed range - spindle: 5.000 1/min spindle nose: JIS A2-6 spindle bore: 73 mm bar material dia. max: 65/52 mm spindle bearing diameter: 120 mm C-Axis: 0,001 ° Number of Turrets: 3 . Number of tool stations: 16 x 3=48 pos Schank height for square tool: 20 mm Diameter of boring bar: 32 mm turret changing time (4-stations): 0,18 sec Number of driven tools: 16 x 3=48 pos max. spindle speed driven tools: 6.000 U/min. Rotary tool machining ability: M16 / Ø16 . rapid traverse X-axis: 30 m/min rapid traverse Y-axis: 20 m/min rapid traverse Z-axis: 50 m/min drive capacity - spindle motor: 25 / 22 kW power capacity - driven tools: 7,5 / 5,5 kW total power requirement: 92,7 kVA weight of the machine ca.: 9,4 t dimensions of the machine ca.: 4,0 x 2,8 x 2,4 m Accerories Chip conveyor Coolantsystem C-axis in main and sub spindle Y-axis 2 x part counter total counter tool setting Overhead partsgripper with conveyor belt. Spindle 1 Chuck SMW KNCS-N 210 / 52 mm Pgjdpfx Asxq E Ewsdyou Spindle 2 Collet Chuck Hainbuch Spanntop nova Kombi Axfix 65 Robot interface Lehmann Robot with parts belt for feeding and disposal CNC Turning- and Milling Center MORI SEIKI NZ 2000 T3Y2 The NZ2000 T3Y has 2 spindles and 3 turrets, and 2 turrets have the Y-axis function and built-in milling motors. This not only allows synchronized machining using 3 turrets, but also achieves heavy-duty cutting and high-speed machining using rotary tools thanks to the built-in motor turrets. For shaft parts loading and unloading there is a Lehmann Robot conveyor belts for loading and unloading . *

Condition: used, Year of construction: 2013, x-travel 650 mm y-travel 600 mm Pgodjuwv Dlspfx Adyeu z-travel 500 mm Control iTNC 530 Heidenhain turning speeds 18.000 U/min power capacity - main spindel 10 / 15 kW tool taper HSK A 63 rotary table dia. 630 mm center bore 32 H7 Swivel range A: ° rotatable C: 360 ° max. table load 1.000 kg number of toolpositions 32 pos. tool taper HSK A 63 max. tool diameter 80 mm max. tool-dia with free toolbox 125 mm max. tool length 300 mm max. tool weight 8 kg rapid traverse ( X / Y / Z ) 60 m/min Accelaration 10 m/s² feed power 8.500 N total power requirement 43 kVA weight of the machine ca. 9,5 t dimensions of the machine ca. 15 x 7,5 x 3,5 m 5 Axis - CNC Machining Center Universal HERMLE - C 30 U - 2x Hermle C 30 U Linear axes dynamic version 6-fold rotary union Blown air through the center of the spindle Automatic cabin door Rotating transparent window - 1x Kuka KR 180 R2900 prime 6 axes Load capacity: 180 kg Reach: 2,896 mm 66x spaces for workpiece pallets 2x changing places 1x turning station 8x gripper spaces - incl. 1x Schunk gripper - incl. 66x workpiece pallets - incl. 64x HSK 63 holders - incl. 20x collets Also available as a single machine Hermle C 30 U.

Condition: used, Pneumatic pick & place manipulator, loading unit similar to SCARA robot. Handling device, handling system, placement gripper, loading gripper for automation. Horizontal axis with guided cylinder linear module type CLM 100-H100 (GEMOTEC column module). Vertical axis with guided cylinder linear module type CLM 100-H50 (GEMOTEC column module). Payload: max. 2 kg Horizontal stroke: 100 mm (pneumatic) Vertical stroke: 50 mm (pneumatic) Vertical adjustment on both support columns: 330 mm (manual, with clamping) Support columns, vertical guide column: Ø 55 mm Mounting base: 175 x 90 mm - Pneumatically traversable in two axes with precise linear guidance - End position dampers - Mounting plate for tool attachment 55 x 65 mm Pgedpfoxf Ur Asx Adyeu Required space (L x W x H): 320 x 170 x 550 mm Net weight: 16 kg Very good condition Various manipulators available, see our webshop.

Condition: used, Year of construction: 2014, Control Unit: R-30 iB This robot operates as a loading and unloading robot in a cell equipped with the Paul Koester leak test (Lot 2770019). Axes: 6 Maximum Payload: 70 kg Reach: 2050 mm Repeatability: ±0.04 mm to ±0.07 mm Motion Range: J1: ±360° J2: ±225° J3: ±440° J4: ±720° J5: ±250° J6: ±720° Maximum Axis Speeds: J1: 160 °/s J2: 120 °/s J3: 120 °/s J4: 225 °/s J5: 225 °/s J6: 225 °/s Mechanical Weight: approx. 560 kg The machine/asset does not include any product-related tool/fixture or gripper (robot). Pgodpoxgp T Djfx Adyou

Condition: like new (used), Year of construction: 2008, operating hours: 58,000 h, functionality: fully functional, super well-maintained injection molding machine from clean room (pharmaceutical production) - fully functional with functional guarantee - with GEKU SR 500 ST. linear robot - perfect optical condition Technical data Manufacturer Engel Type e-max 200/100 Pjdjubamvepfx Adyjgu serial number 170609 Year of construction 2008 Operating hours 58774 h approx. Dimensions L/W/H 4.0 x 1.3 x 1.9 mtr. Weight 3,900 kg Fully functional Condition excellent Clean room Special Control unit CC200 Screw ⌀ 25 mm Injection weight 55 gr./hp Injection pressure 2400 bar Injection volume 59 ccm Clamping force 1000 kN / 100 to. Distance between tie bars 460 x 410 Clamping platens 650 x 600 mm mold mounting height 150-450 mm max distance between platens 800 mm Opening stroke 350 mm Ejector stroke / force 100 mm / 25 kN Clamping unit electric Connected load: 45 KW Rated current: 69 A The machine is immediately available in our warehouse in Hanover/Germany and has been tested. Extras GEKU Robot SR 500 ST Simotion control X-axis: 600 mm Y-axis: 1400 mm vertical Z-axis: 2500 mm horizontal A-folding axis: SWM 45 C-axis : Servo Gripper: SWS16 B-axis: not available Guarantee Warranty until first commissioning Loading/shipping FCA-free loading on the buyer's truck or free delivery against freight reimbursement from our warehouse in Hanover /Germany Financing On request - installment plan option Price: On request

Condition: used, _____ Description: Year of manuf. : 2008 Control : Siemens 840 Speed : 8000 rpm Movement X/Y/Z : 800/800/800 mm Tool holder : HSK 100 In General: Year of manufacture:2008 Speed:8,000 rpm Tool holder:HSK 100 Control system:Siemens 840 D Travel X/Y/Z:800/800/800 mm Table speed:700 rpm Spindle: Technology:Geared spindle Speed:8,000 rpm Max. power:28 kW Max. torque:727 Nm Tool holder:HSK-100 Turning function:Spindle clamping NC swivel head: Technology:Universal milling head B-axis:0.001° NC- Millturn table: Max. speed:700 rpm Clamping surface:800 x 630 mm Max. table load:800 kg Tool magazin: Technology:Chain magazine Number of stations:120 Tool changer:Double gripper Equipment: Chip disposal:Chip conveyor Coolant supply:IKZ system, 80 bar Coolant temperature control:Immersion cooler Position measuring systems:Direct in all axes Automation:2-fold pallet changer Turning function:Spindle clamping + rotary table Workpiece measurement:Preparation for measuring probe Podpfowx A Hqex Adyogu Process monitoring:Operating mode 4 Set-up mode:Electronic handwheel Emulsion mist separator:Mechanical separator

Condition: used, Year of construction: 2014, Design: -> Dual-spindle Spindle: -> Tool holder HSK63 -> Speed 17,500 rpm Linear Axes: -> X-axis 600 mm -> Y-axis 600 mm -> Z-axis 400 mm Tool Changer: -> 84 positions (42 per spindle) Work Stations: -> OP10: 4-axis (rotary axis/swivel beam) -> OP20: 5-axis (rotary axis/swivel beam + 2 rotary tables) Operating Data: Psdpfxsxgphbo Adyegu -> Spindle hours approx. 22,000 -> Operating hours approx. 48,000 Machine/asset does not include any product-related tool, fixture, or gripper (robot). The machine operates with a FANUC M710iC robot as a loading and unloading unit. The robot is not included in the scope of delivery and can be purchased separately (Lot 2770023).

Condition: used, _____ 2 Pieces of Pfiffner RT 100-12 Description: Year of manuf. : 2013 Control : Siemens 840 D Rotary-Indexing-table/Spindle: Clamping stations:12 motorised spindles Drive:Torque drive, water-cooled Position measuring system:Direct Switching time:1.5 seconds Spindles:Water-cooled motor spindles C-axes:0.001°, hydraulic clamping Speed:5,500 rpm Power:11 kW Podpfx Adsw Si T Aeyjgu Clamping device:Chuck Basic modules: Technology:Positioning module, 3-axis X-axis:50 mm Y-axis:100 mm Z-axis:100 mm Position measuring systems:Direct in all axes Coolant supply:Integrated : : Workpiece size (max.):100 x 100 x 100 mm Station 1: Horizontal:feeding of raw parts (indexing conveyor + Stäubli robot) Vertical:Measuring raw part Station 2: Horizontal:4-fold turret without drive Vertical:Measuring reclamping error (C-axis zeroing) Station 3: Horizontal:4-fold turret without drive Vertical:Not used Station 4: Horizontal:4-fold turret without drive Vertical:Not used Station 5: Horizontal:6-position turret with WAN, 10,000 rpm Vertical:6-position turret with WAN 10,000 rpm Station 6: Horizontal:4-fold turret without drive Vertical:Not used Station 7: Horizontal:6-position turret with WAN, 10,000 rpm Vertical:Not used Station 8: Horizontal:6-position turret with WAN, 10,000 rpm Vertical:Not used Station 9: Horizontal:4-fold turret without drive Vertical:Not used Station 10: Horizontal:6-position turret with WAN, 10,000 rpm Vertical:Not used Station 11: Horizontal:6-position turret with WAN, 10,000 rpm Vertical:6-position turret with WAN 10,000 rpm Station 12: Horizontal:Charging/discharging unit with double swivelling gripper + discharging belt Equipment: Chipmanagement:Chip conveyor High preassure unit:Cooling unit 50 bar Toolmonitoring:Toolbreaktagecontrol ARTIS Rawmaterialfeed:Conveyorbelt with robot Finishpartremoval:Conveyor with 3-way switch Oilmistseparation:Electrostatic filter Fire extraction system:Kraft + Bauer Part labelling:Laser Parts cleaning:HESO cleaning system

Condition: used, Year of construction: 2020, Design: -> Dual-spindle Linear Axes: -> X-axis 600 mm -> Y-axis 600 mm -> Z-axis 400 mm Spindle: -> Tool holder HSK63 -> Speed 17,500 rpm Tool Changer: -> 84 positions (42 per spindle) Swivel Beams: -> 2 units (4-axis machines) Operating Data: -> Spindle hours approx. 9,354 -> Operating hours approx. 21,130 Machine/Asset does not include any product-related tool/fixture or gripper (robot). Pgsdpfsxgpbzox Adyou

Condition: used, Year of construction: 2020, Design: -> Dual-spindle linear axes: -> X-axis 800 mm -> Y-axis 900 mm -> Z-axis 650 mm Spindle: -> Tool holder HSK63 -> Speed 17,500 rpm Tool Changer: -> 84 positions (42 per spindle) Swivel Beams: -> 2 units with 2 rotary axes each (5-axis machines) Operating Data: -> Spindle hours approx. 10,993 -> Operating hours approx. 22,851 The machine/asset does not include any product-related tool/fixture or gripper (robot). Psdpfx Asxgpa Redyogu

Condition: used, Year of construction: 2016, 5-Axis Working Area: -> X-axis 1500 mm -> Y-axis 1250 mm -> Z-axis 880 mm Feed / Rapid Traverse: -> X-axis 100 m/min -> Y-, Z-axis 100 m/min Axis Acceleration: -> X-, Y-axis 7 m/s² -> Z-axis 10 m/s² -> Jerk 150 m/s³ Table Load Capacity: -> Max. weight 400 kg Spindle: -> Tool holder HSK 100 -> Speed range 10,000 rpm -> Power (S6/40% duty) 40 kW -> Max. torque 175 Nm Tool Magazine: -> Positions 36 -> Max. tool length 520 mm -> Max. tool diameter (with free adjacent slot) 205 mm -> Max. tool weight 20 kg Pgedpfx Aexgn Sledysu -> Total load 200 kg -> Tool change time 3 s Machine/Asset does not include any product-related tool, fixture or gripper (robot).