Used Mechanical Forging Press for sale (18,029)

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm Pgedpfszuzw Dex Aqior for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Manufacturer: OTT Type: 300-K-D0 Year of manufacture: 1996 Pgodpfezuzwwsx Aqior Technical data Plate dimensions: 2550 x 1350 mm Hot water heating 6 pressure cylinders Total pressing force: 135 t Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2007, Lamination press Manufacturer: Dimter Type: PROFIPRESS L2500 Year of manufacture: 2007 Technical data Wood dimensions to be processed Wood width, panels: 30 - 150 mm Wood thickness: 11 - 60 mm Wood inlet length: 800 - 2500 mm Panel widths, variable: max. 1300 mm Specific pressing pressure for cross-sections of 2500 x 60 mm: up to 1.6 N/mm2 The pressing surface per press cycle must not be smaller than 100 cm2 Filling width of the press per cycle: min. 650 mm / max. 1300 mm Max. filling area of the press per cycle: 3.25 m2 (The max. usable press width depends on the widths of the individual lamellas.) Podpfozuzwqsx Aqiogr Wood type Softwood/hardwood Press without options Electrical connection, press: 7 kW Electrical connection, 40 kW generator: 56 kW Operating voltage: approx. 400 Volt / 50 Hz (C/s) Collection table extended to 3700 x 1300 mm, with stainless steel wood support Motor-driven multi-function slider Lamination press Profipress L 2500 Press bed area approx. 2500 x 1300 mm Sturdy base frame with lower press table made of stainless steel as a grounding electrode Quick-change stop guide sets for panel thicknesses of 19 - 40 mm, which can be hydraulically adjusted to the current filling width Hydraulic special pressure elements ensure uniform pressure distribution over the entire joint length and compensate for tolerances In multi-lane operation, filling widths may vary by a maximum of 15 mm Upper pressure plate with hydraulic drive generates high vertical pressing pressure for minimal displacement Integrated hydraulic unit for generating pressing force and driving the hydraulic motors Control cabinet and control panel Protective cladding Additional individual pressure elements from above Automatic gluing station with precision gluing head Infeed for different widths Camera Washing and rinsing device for gluing head Modem incl. software for online connection Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm - Min. filling height 900 mm Psdpfezuzwkex Aqiogr - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm - Max. power 13.2 kW - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Continuous body press Manufacturer: LIGMATECH TYPE: MPP 15 Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Working height: 500 mm Transport speed: min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Pgedpfx Aozuzv Teqijr Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2000, Corrugated board press Manufacturer: Hüttenhölscher Year of manufacture: 2000 Technical data Voltage: 400 V Pjdozuzvmepfx Aqisgr Current: 32 A Frequency: 50 Hz Compressed air: 6 bar Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2003, Technical details: Podpfx Aqozvnrdsijgr Pressure: 60 t stroke: 400 mm table surface area: 700 x 700 mm passage opening in table: Ø 100 mm distance between columns: 700 mm distance between columns: 700 x 1300 mm table height over floor: 850 mm dayligth: max. 1150 mm daylight dimension : table/slide up: 400 - 800 mm cylinder diameter: Ø 110 mm total power requirement: 4,8 kW machine weight approx.: 930 kg dimension machine approx.LxWxH: 1,2 x 0,7 x 3,0 m HYDRAULIC DOUBLE COLUMN PRESS Special construction welded from 25 mm sheet steel Operating mode: single stroke Punch holder: pin M 70 x 2.5mm and punch Ø 128 x 440mm Table protection housing Round punch Ø 130 x 120 mm Hydraulic unit *

Condition: used, Year of construction: 2001, Short-cycle pressing line Manufacturer: Wemhöner Type: KT-F-1E Year of manufacture: 2001 Technical data - Pressing area: 5,750 mm x 2,200 mm - Operating side: left - Plate dimensions: Length: 2 x 2,600 mm - 2 x 2,620 mm Width: 2,070 mm Thickness: 6 mm - 40 mm - Pressing pressure: approx. 40 kg/cm² Pgjdpfxszuzi To Aqisr Note: Upon request, the complete layout plan of the system can be sent. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 1998, - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Door pressing system Pgsdpfozuzgrjx Aqior Manufacturer: Wild Year of manufacture: 1998 For door dimensions: - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Consisting of the following sections: 1. Continuous door panel gluing with frame assembly station / 2. Pressing line with hardboard facing station Section 1 consists of: - Gantry loading system - Angle transfer with longitudinal and cross saws - Loading and feeding of the longitudinal and transverse frame parts from magazines - Longitudinal cutting station for the longitudinal frame parts - Connecting station of the frame parts with the door panel core. With clamping devices - Conveyor belt angle transfer with shuttle transfer of the door panel cores onto the glued hardboard Section 2 consists of: - Loading of the hardboard - Brush cleaning machine - Hardener application machine from below - Glue application machine from below - Roller conveyor - Angle transfer for the lower hardboard - Vacuum reversing device for the upper hardboard - Automatic facing station for hardboard and door panel cores - 2 door presses, each with 2 x 4 pressing stations, arranged parallel to each other - Both presses are loaded at the infeed with 1 shuttle loading basket - Both presses are unloaded at the outfeed with 1 shuttle unloading basket - Angle transfer to the infeed into a hedgehog buffer - Angle transfer at the outfeed of the hedgehog buffer and feeding to the stacking station - One-sided vacuum stacking with protective plate space Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: excellent (used), Year of construction: 2004, operating hours: 76 h, machine/vehicle number: HF112305, Size 47 x 66 cm, Console DTC (Sakurai Delivery Top Console) with Touch Screen, Full Remote Control Operation, SIS (Sakurai InterActive System) for make-ready, Plate Running Register system, SAS (Sakurai Auto Set) for paper size and thickness, SPC (Semi-automatic Plate Change), Cocking Register, Automatic Washers: Blanket Cylinders & Inking Rollers, Olivermatic Dampening, Baldwin Refrigeration System & Bal Control, Feeder with Suction-belt feed table, Electronic Double Sheet & Side Lay Detector, Chromed Impression Cylinders, Perfector 4/0 - 2/2 (Fully automatic), Semi-High Pile delivery, Powder Spray. Pgedpfx Aozubgroqisr

Year of construction: 1999, condition: ready for operation (used), - USED - 6-AXIS SYNCHRONIZED CNC PRESS BRAKE WITH HYDRAULIC CROWNING AXIS: Y1 - Y2 - X - R - Z1 - Z2 BENDING LENGTH: 3100 mm TONNAGE: 165 ton THROAT DEPTH: 450 mm DISTANCE BETWEEN UPRIGHTS: 2600 mm OPEN HEIGHT: 440 mm UPPER BEAM TRAVEL: 250 mm Pgedpfx Ajrk Sg Roqior APPROACH SPEED: 100 mm/sec RETURN SPEED: 120 mm/sec WORKING SPEED: 0-10 mm/sec MOTOR POWER: 18,5 kW CONTROL UNIT: DELEM DA 65 WEIGHT: 12020 Kg OVERALL DIMENSIONS: 4100 x 1880 x 2920 mm NOTE: No 2 FRONT SUPPORT BRACKETS; BOTTOM HYDRAULIC TOOL LOCKING

Year of construction: 2003, condition: ready for operation (used), - USED - 7-AXIS SYNCHRONIZED CNC PRESS BRAKE    AXIS: Y1 - Y2 - X - X1 - R - Z1 - Z2 BENDING LENGTH: 3150 mm TONNAGE: 70 ton THROAT DEPTH: 400 mm DISTANCE BETWEEN UPRIGHTS: 2640 mm OPEN HEIGHT: 450 mm APPROACH SPEED: 160 mm/sec RETURN SPEED: 160 mm/sec WORKING SPEED: 0-10 mm/sec MOTOR POWER: 15 kW Pjdpfx Asrk Shceqiegr CONTROL UNIT: ESA KVARA WEIGHT: 7800 Kg OVERALL DIMENSIONS: 3400 x 2100 x 2650 mm

Year of construction: 2010, condition: ready for operation (used), - USED - 6-AXIS SYNCHRONIZED CNC PRESS BRAKE WITH HYDRAULIC CROWNING AXIS: Y1 - Y2 - X - R - Z1 - Z2 BENDING LENGTH: 3200 mm TONNAGE: 100 ton THROAT DEPTH: 500 mm DISTANCE BETWEEN UPRIGHTS: 2550 mm OPEN HEIGHT: 600 mm UPPER BEAM TRAVEL: 400 mm Pedpfx Astq Ngboqiegr X-AXIS TRAVEL: 800 mm R-AXIS TRAVEL: 150 mm APPROACH SPEED: 200 mm/sec RETURN SPEED: 180 mm/sec WORKING SPEED: 10 mm/sec MOTOR POWER: 11 kW CONTROL UNIT: ESA 875 PLUS WEIGHT: 10500 Kg OVERALL DIMENSIONS: 4300 x 2000 x 3100 mm NOTE: MACHINE EQUIPPED WITH NEW CNC ESA

Year of construction: 2000, condition: ready for operation (used), - USED - 4-AXIS SYNCHRONIZED CNC PRESS BRAKE AXIS: Y1 - Y2 - X - R BENDING LENGTH: 3130 mm TONNAGE: 80 ton THROAT DEPTH: 405 mm DISTANCE BETWEEN UPRIGHTS: 2700 mm OPEN HEIGHT: 350 mm UPPER BEAM TRAVEL: 150 mm APPROACH SPEED: 100 mm/sec RETURN SPEED: 96 mm/sec WORKING SPEED: 9 mm/sec MOTOR POWER: 5,5 kW Pgedsmyc I Nepfx Aqior CONTROL UNIT: TASK 84 SIRIO 2 WEIGHT: 6500 Kg OVERALL DIMENSIONS: 4000 x 1700 x 2400 mm

Condition: used, Year of construction: 1989, machine/vehicle number: SN: 00789901, functionality: unexamined, pressing force: 815 t, Press 1, manufacturer: Umformtechnik Erfurt GmbH, type: PKZZI 800.1/3150x1600/500E, serial number: 00789901, year of manufacture approx. 1989, 8000 kN, last service in 10/2025, machine in operation until 12/2025. Technical data of the press according to the nameplate: Press force max. 8,000 kN – at a distance in front of the die of 12.5 mm Press force 2,500 kN – at a distance in front of the die of 200 mm Stroke rate in idle 10 to 20 min-1 Stroke of the ram 500 mm Adjustability of the ram: 500 mm Strip feed system consisting of: Roller feed, manufacturer: GSW Schwabe, type VRMA80/78, machine no. 2011-60187, year of manufacture 2011 with reel 1 (sandwich processing), SAWAB reel, year of manufacture 2011 with reel 2, manufacturer: GSW Schwabe, type: LMHR1000/1100, no.: M2011-00171, year of manufacture 2011 with reel 3, manufacturer: GSW Schwabe, type: MHR5/1400, serial no.: M2011-00170, year of manufacture 2011 including enclosure GWS project no.: 2011-60187 with peripherals: - Conveyor belt - Raziol system Function and technical data not verified without additional items/without further accessories, unless explicitly stated as part of the item Pgedpfszvdm Rex Aqior WE STRONGLY RECOMMEND PARTICIPATING IN THE INSPECTION! If interested, please contact us via email!

Condition: used, Year of construction: 1998, machine/vehicle number: SN: 5-2067, functionality: unexamined, power: 45 kW (61.18 HP), pressing force: 255 t, overall weight: 24,800 kg, PME Erfurt, Type: ZH 2500 / 1600, Serial No.: 5-2067, Year: 1998, 2500 kN, in operation until December 2025 Technical data of the press according to the nameplate: Press force: 2,500 kN Stroke rate: 25-75 strokes/min Rated stroke rate: 40 strokes/min Stroke: 20-200 mm Ram adjustment: 140 mm Total power: 45 kW Operating voltage: 400 V Frequency: 50 Hz Machine weight: 24,800 kg Strip feeding system consisting of: PBK, Type: Roller feeder WV-120/DSM 500P, Serial No.: BA00482, Year: 1998, PBK, Type: Straightening machine, Year: unknown, PBK, Type: Unwinding reel SCi 530 M, Serial No.: BA00482, Year: 1998 including enclosure and roller conveyor with peripherals: Pedszvcxlspfx Aqiogr - Conveyor system Functionality and technical data have not been verified. without additional items/without further accessories, unless explicitly stated as part of the item. If interested, please contact us by email.

Condition: used, Year of construction: 2019, machine/vehicle number: M01645/400/23/051/19, functionality: unexamined, power: 75 kW (101.97 HP), Schuler, Type: Eccentric press MC400, Machine No. M01645/400/23/051/19, Year of manufacture 2019, 4000 kN Technical data of the press according to the nameplate: Supply voltage: 3LNPE/400V/50Hz Control system: CCS/PNOZmulti Fuse rating: 250 A Rated power: 75 kW Rated force: 4,000 kN Work capacity: 60,000 J Max. strokes in continuous operation: 20-80 strokes/min Max. strokes in single-stroke operation: 30 strokes/min Max. clutch cycles in single-stroke operation per minute: 20 Post-travel time: 0.20 sec Min. safety distance: 322 mm Min./max. clutch pressure: 5.5/6.0 bar System pressure: 6.0 bar Stroke lengths: 40-315 mm Maximum ram adjustment: 200 mm Standard connection point of the ram: OU Max. installation space, largest stroke in UU: 750 mm Table dimensions: 3000 x 1400 mm Max. tool dimensions: 3000 x 1300 mm Max. weight of tool upper part: 2,800 kg Weight without additional equipment: 72,000 kg Strip feeding system consisting of: GSW Schwabe, Type: MHR 5/2000, Serial No. M 2018-01118, Year of manufacture 2019 GSW Schwabe, Type: RMA 50/79, Serial No. M 2018-01119, Year of manufacture 2019 Including hydraulic unit, enclosure, and roller conveyor GSW project no.: 2018-60420 with peripherals: - SCHÄFER lubricant supply system with tank - RAZIOL EST-10-D ELS-400, Year of manufacture 2018 - Conveyor belt - GÜTHLE ACT10F2000/2400N, Set of 2, Year of manufacture 2019 - Control cabinet Function and technical data have not been verified. Pgodpfxjzvcgpo Aqisr Without further items/without further accessories, unless explicitly specified as part of the item. If interested, please contact us by email.

Condition: excellent (used), Year of construction: 2004, AMADA MODEL HFE 103-3 100 tons capacity x 3000 bending length hydraulic downstroking press brake complete with OP 2000 7 AXIS cnc control, ERWIN SICK machine mounted electronic guards , side and rear interlocked fencing Model Amada HFE 100-3 downstroke CNC Press brake Year 2004 Tonnage 1000 KN Type OP 2000 CNC Controlled Axis Y1, Y2, X, R1 R2 Z1 Z2 Psdoyt H Awjpfx Aqiogr Max. Bend Length 3000 mm Open height 470 mm Stroke Length 200 mm Approach Speed 100 mm/sec Bending Speed 1 - 10 mm/sec Return Speed 1-100 mm/sec Oil Capacity 110 LITRES Motor Power 11 kw Weight 6800 KG kg CNC Control Backgauge Stoke (X axis) 700 mm/s Max gauge 1000mm R axis 250mm can be demonstrated under power BROCHURE AND FURTHER INFORATION AVAILABLE UPON REQUEST

Condition: good (used), Year of construction: 1963, Stroke = 250 mm On request, transport and loading can be organized across Europe at an additional cost. Prices excl. VAT Inspection possible by appointment. Contact us – our team will be happy to assist you. Machinery Purchase / Sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES, MACHINE TOOLS, ETC. Do you need a high-quality yet affordable machine for your production? Or do you want to sell your equipment? Pgedezvnd Tspfx Aqier For further information or contact options, please use the contact form.

Condition: good (used), Year of construction: 2012, Condition: 2012 overhauled to the latest UVV Installation height: 800 mm Pgodpfjzvnfdex Aqisr Ram stroke: 500 mm Projection: 360 mm Nominal force: 400 kN Hydraulic pressure: 160 bar Operating hours: 1356 Other: new control from Pilz, electrical circuit diagrams available Video about functionality available

Condition: used, functionality: fully functional, Brianzola Simcor embossing press Working width 400 mm Two feed speeds: 1.5/3 m/min 9 embossing heads Technical documentation Psdpfx Aqozwc Aajiegr

Year of construction: 1999, condition: used, Colour: Grey Membrane press Orma PM/AIR Year of construction 1999 Serial number 52850199 Dimensions 2300*900mm Max panel size 2200x800mm Max panel thickness 40mm 8 cylinders diameter 100mm Stroke 150mm Pressure 160T Pressure pressure 6 kg/cm² Heating 13kW Total power 17.3kW 380V, 35Amp Pgedpownhicjfx Aqier Dimensions: 3900x1800xH2100mm, weight 5900kg - Year: 1999 - Documentation available: No - CE certificate present: No - Serial number: 52850199 - Main motor power [kW]: 17.3 - Max. workpiece length [mm]: 2200 - Max. workpiece width [mm]: 800 - Max. workpiece height [mm]: 40 - Number of cylinders [pcs.]: 8 - Cylinder diameter [mm]: 100 - Total working pressure [Ton]: 160 - Working pressure [kg/cm²]: 6 - Heating boiler present: Yes Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, total length: 11,500 mm, total width: 2,450 mm, total height: 2,600 mm, Colour: Green Empty weight: 16.500 kg Veneer press Feed-through press HOT Colombo Machine dimensions: 4400x1400 Oil heated input/output is included 8 cylinders Complete with glue roller etc. - Documentation available: No - CE certificate present: No - Press drive: Hydraulic - Max. workpiece length [mm]: 4500 - Max. workpiece width [mm]: 1400 - Max. workpiece height [mm]: 140 - Total stroke [mm]: 140 - Number of stages [pcs]: 1 - Material of press plates: Steel - Number of cylinders [pcs]: 8 - Cylinder diameter [mm]: 85 - Working pressure [kg/cm²]: 4 Pgodownhvvepfx Aqier - Heating type: Oil heated - Voltage [V]: 400 - Transport dimensions: 11500mm x 2450mm x 2600mm (l x w x h) - Transport weight [kg]: 16500kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: good (used), Lechner IV B Hydraulic Bookbinding Press The machine is ready to operate. The press has a built-in hydraulic unit. Four stations. Pgodpszv Nlxjfx Aqijr Irreplaceable in bookbinding for the production of books, pads, etc.

Condition: good (used), Year of construction: 1982, Press force: max. 200 kN Safety distance: 100mm Pgedpfxezvfp Ho Aqier Post-travel: max. 10 mm Motor power: 3 kW