Used Strech Blowing Machine for sale (64,916)

Condition: good (used), Year of construction: 1998, operating hours: 89,340 h, functionality: fully functional, screw diameter: 90 mm, overall weight: 16,000 kg, clamping force: 650 kN, total width: 2,750 mm, total length: 5,600 mm, total height: 3,200 mm, Manufacturer: Sterling Model: 15 LBS Year of manufacture: 1998 Operating hours: 89,340 h Fsdpjzfxwisfx Al Ujpn Closing force: 650 kN Screw diameter: 90 mm BM Sterling APV, year of manufacture 1998 Complete control system replacement in 2008 with MACO-sys 6000, performed by Davies-Standard LTD Net price: 45,000 EUR

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Fedpfsg Ailcsx Al Uopn Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, Equipment: documentation/manual, For sale: Complete PET bottle blowing line TES BluLine4 HiTech MultiFlex (2017) We offer for sale a complete PET bottle production line from the renowned manufacturer TES Sp. z o.o., model BluLine4 HiTech MultiFlex, manufactured in 2017. The machine is in very good technical condition, regularly used, and ready for further operation. Technical data Manufacturer: TES Sp. z o.o. Model: BluLine4 HiTech MultiFlex Year of manufacture: 2017 Bottle capacity range: 0.5 l – 4 l Number of cavities: 2-4 The line includes: ✅ Preform feeder ✅ PET bottle blowing machine ✅ Bottle packer for trays Advantages of the equipment Complete and ready-to-use production line Universal range of produced capacities Solid construction and proven TES technology Very good technical condition Ideal for manufacturers of beverages, water, household chemicals, and other products packaged in PET bottles Price: negotiable. If you have any questions or would like to obtain additional information, please contact us by phone or private message. We will gladly provide detailed information and send additional photos of the equipment. Fsdpfxezd Sb Se Al Uopn

Condition: good (used), Year of construction: 1994, functionality: fully functional, Manufacturer: S.P.A Magic M.P. Fsdpfoxxp Tbjx Al Uepn Model: MGL2D This blow molding machine is fully functional. It is still in production and can be inspected by appointment. Videos can be provided upon request. PRICE REDUCTION!!! From 21,000 to 19,000 EUR!

Condition: used, Year of construction: 2018, functionality: fully functional, If you have any questions or need more information, feel free to send us a message or give us a call. Fpodpfx Aoz D T Auol Uen

Condition: used, Year of construction: 2020, functionality: fully functional, clamping force: 2,500 kN, total width: 12,500 mm, total length: 11,500 mm, total height: 8,600 mm, power: 831 kW (1,129.84 HP), Equipment: documentation/manual, For sale is a highly automated BBM 2500 CoEx3 extrusion blow molding machine, manufactured in 2019. The machine is in very good technical condition, fully functional, and immediately available. An inspection while the machine is running can be arranged by appointment. The machine is designed for the economical production of large-volume HDPE hollow bodies and sophisticated technical blow-molded parts. It is a batch-type 3-layer extrusion blow molding machine with a parison accumulator head. The offered scope of supply includes: - Piovan GMS-160 high-performance plastic granulator, manufactured in 2023 - Piovan VM 500 extraction system - GWK/Technotrans cooling unit The listed peripheral components are included in the offer price. If individual components or the entire range of accessories are not required, they can be removed from the scope of supply, and this will be taken into account when determining the price. Technical key data: Manufacturer/Model: BBM 2500 Year of manufacture: 2019 Process: CoEx3 extrusion blow molding with parison accumulator head Material: HDPE Design: 1 station with 1 CoEx3 blow head 3 extruders: 1 × 130 mm and 2 × 70 mm Total output: up to 1,200 kg/h Accumulator volume: 1 × 20 l and 2 × 7.5 l Electrical wall thickness control Clamping force: 2,500 kN Platen area: 2,160 × 2,400 mm Column spacing: 1,500 × 2,400 mm Opening width: 600–1,500 mm Electrical closing movement Locking via 6 hydraulic power strokes 2 integrated KUKA 6-axis robots for removal and handling Fully automatic KOCH material feeding system with gravimetric dosing and mixing Beckhoff TwinCAT control with Siemens components and drives Connected power: 831 kW Power supply: 400 V, 3 phases/N/PE, 50 Hz Dimensions: approx. 11,500 × 12,500 × 8,600 mm (L × W × H) CE documentation and machine manuals available The machine is particularly suitable for large-volume hollow bodies, technical molded parts, infrastructure products, sanitary parts and industrial containers. Fpjdpjzw D Haofx Al Uon Availability: immediate Inspection and trial run: possible by prior appointment

Condition: excellent (used), Year of construction: 2013, operating hours: 200 h, functionality: fully functional, screw diameter: 65 mm, overall weight: 9,000 kg, clamping force: 785 kN, total width: 1,800 mm, total length: 4,500 mm, total height: 3,000 mm, power: 0.045 kW (0.06 HP), We offer for sale a slightly used injection blow moulding machine in excellent condition. It is connected and fully operational for demonstration purposes. We can also offer several ready-made molds for canisters and lamp shades. The machine is designed for use with PMMA, PC, PP, and PE resins. Fpodsthk Rzopfx Al Uen

Condition: used, Speed: 8.000 bph with 0,5 liter bottle. Different formats are possible optionaly. Dismanteling is made by Seegräber GmbH on begining februar 2018. List of machines included: -SIDEL SBO 6 Blowing machine. Completly overhault by SIDEL in 2006. Fedpfxjz Icmwo Al Uspn -Preform magazin and preform elevator Compressor, cooling, moulds not included

Condition: like new (used), Year of construction: 2022, operating hours: 200 h, functionality: fully functional, screw diameter: 70 mm, overall weight: 600 kg, clamping force: 80 kN, total width: 2,800 mm, total length: 4,000 mm, total height: 2,260 mm, Main Features: 1. Computer Control System (PLC) – Japanese Mitsubishi PLC 2. Electrical Cabinet – All electrical components are sourced from globally renowned brands, ensuring quality and stability. 3. Touch Screen – Innovation computer control system 4. Advanced Hydraulic Cylinder from Germany 5. Linear Guideway 6. ABB Inverter from Switzerland & Rexroth from Germany 7. Large Diameter Galvanized Steel Pipes 8. Electric Lifting Platform 9. Ceramic Heater 10. Hydraulic System & Valve Connections – From Yuken Industry Technical Specifications: • Suitable Material: PE, PP, and others • Max Volume: 6 L • Production Capacity: 170-260 pcs/h • Dimensions: 4.0 × 2.26 × 2.8 m • Weight: 6T Plasticization System: • Reducer: Hard finishing, high strength, low noise • Screw: Ø 70 mm, L/D ratio 24, 38CrMoALA, cooling system available • Plasticization Capacity: 100 kg/h (HDPE) • Heating Zones: 3-4 aluminum heaters, automatic heating • Heating Power: 12 kW/h • Extruder Motor: Three-phase asynchronous motor (380V, 50HZ) • Cooling Fan: 4 zones, automatic cooling Extrusion System: • Material: High-grade alloy steel, central feeding • Number of Die Heads: 1 • Max Die Mouth Diameter: Ø 160 mm • Heating Zones: 4, stainless steel heating cycle • Heating Power: 5-7 kW Clamping System: • Features: High strength, rigidity, central mold locking, stable mold opening & closing • Clamping Force: 80KN • Template Distance Adjustment: 170-520 mm • Max Mold Size: 380 × 420 mm Electric System: • Automatic Monitoring, Fault Alarms, Auto Counting, Auxiliary Functions • Control Interface: Touchscreen with self-diagnosis alarm system • Temperature Control: Automatic temperature control module • Motion Control: Inovance (Chinese/English version) Hydraulic System: • Features: Multi-functional integrated hydraulic block, proportional control, high efficiency • Oil Pump Motor: Three-phase asynchronous motor (380V/220V, 50/60HZ) • Oil Pump: Imported double pump • Valves: Imported oil pump valves and connections • Oil Pipes: Double-layer wear-resistant • System Pressure: 60 kg/cm² • Cooling System: Separate water cooling cycle, oil cooler Pneumatic System: Fodpfov Iflpsx Al Uopn • Brand: Taiwan AIRTAC pneumatic system • Air Pressure: 0.6 MPa • Air Displacement: 0.8 m³/min • Electromagnetic Valve: Taiwan AIRTAC Main Components: Electronic Parts: • PLC Control System: MITSUBISHI from Japan • Touch Screen: INOVANCE • Temperature Controller: HUICHUAN • Auxiliary Relay: OMRON • Contactor: Schneider from France • Electric Motor: Three-phase 380V • Power Source: TAIWAN MEANWELL • Transducer: ABB from SWITZERLAND Hydraulic Parts: • Oil Pump: TAIWAN HIGH-TECH • Valve: YUKEN • Oil Pump and Connection: YUKEN • Sealed Part: HALLITE Air Control System: • Cylinder: AIRTAC • Air Valve: AIRTAC This blow molding injection machine was purchased directly from a factory in China for a specific project that was never realized. The machine was used for only one month. Location: Siemianowice Slaskie, Poland We also have peripheral equipment available for sale, such as: • 5 HP AIR COOLING SYSTEM • Auto Loading • 150 kg Color Mixer • Scraps Crusher

Condition: good (used), Year of construction: 2017, functionality: fully functional, LINEAR PET BLOWING MACHINE SET with auxiliary equipment Fpodsquuvrjpfx Al Uon AC ARCOR - multiBlow2 - 2017 Speed: 1,5L - 6000 Cavities: 4 Formats: 0,1 - 3,0L AUXILARY EQUIP 1. Chiller - M.T.A S.p.A - TAE EVO 051 2. LOW Pressure compressor - SHAMAL 45kw 3. Receiver tank - Low pressure - MAX 16Bar 4. Receiver tank - High pressure - MAX 45Bar

Condition: used, Year of construction: 1998, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 16/16 S1 Year of manufacture 1998 Capacity: 16,000 for 1.5 L bottles and up to 19,000 bph for 0.5 L bottles Installed power: 347 kW Includes 1.5 L moulds Preform feeder Chiller cooling unit Fodpfxoutni Re Al Ujpn Technical condition: used machine, functional until dismantled. The machine is currently dismantled, assembled in elements and prepared for transport. Full and original technical documentation.

Condition: excellent (used), Year of construction: 2017, XYZ 2000 Turret Milling Machine (2017) (Ex College) 3 Axis Newhall DRO (X, Y & Knee) Spindle Taper R8 Fodexxb Rrspfx Al Uopn Spindle speeds to 500 – 4200 rev/min Table Size 1270 x 254mm Table Travel: X - 812mm Y - 406mm Knee Travel: Z - 406mm Quill Travel Z - 127mm For sale with Jet Machinery Ltd Jet Machinery Stock No: #79047 Machine Serial Number: 12907 Cost: £9,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: used, Year of construction: 2003, functionality: fully functional, machine/vehicle number: K787016, overall weight: 41,000 kg, input voltage: 400 V, input frequency: 50 Hz, input current: 800 A, operating pressure: 40 bar, control voltage: 24 V, type of input current: three-phase, Equipment: documentation/manual, Krones Contiform S20 PET stretch blow molding machine – 20 cavities, output up to 40,000 units per hour. Used Krones Contiform S20 machine for manufacturing PET bottles. The machine is completely disassembled and prepared for loading onto a truck. Due to its disassembled condition, it is not possible to perform a test run or functional tests – it is sold as a complete set of components for reassembly by the buyer. Technical specifications: Fsdpfx Alez Euubo Ujpn • Manufacturer: Krones • Model / Year: Contiform S20 / [2003] • Number of cavities: 20 • Nominal output (according to the manufacturer's specifications): up to 40,000 bottles/hour • Maximum container volume: up to 3 l (depending on the shape) • Oven: linear, with a 40 mm stroke • Neck size: 26/22 (PCO 1881) Scope of supply: [preform feeder, hopper/elevator and orienting device, chiller, molds, spare parts, etc.] Inspection possible by prior arrangement – the machine can be inspected in its disassembled state, with the components laid out in Kutno. Loading at the buyer's expense. Transport to be agreed. Price on request.

Condition: excellent (used), Year of construction: 2003, PET bottle blowing machine Manufacturer: KRONES Model: CONTIFORM K781 Efficiency: 12,000 bph Includes 1.5 L and 0.5 L bottle molds Power: 150 kW Air requirement: 10 bar - 1500 m3/h, 30 bar - 1000 m3/h Set dimensions (blow mold + preform feeder): 1100 x 340 cm, h: 450 cm Blow mold dimensions: 500 x 340 cm, h: 250 cm Feeder dimensions: 600 x 250 cm, h: 450 cm Air requirement: 10 bar - 1500 m3/h, 30 bar - 1000 m3/h Year of production: 2003 Technical documentation of machine operation Fpedpfx Aovddkvol Uen Very good condition

Condition: used, Semi-automatic PET bottle blow molding machine Manufacturer: FERENC Model: F-1400 Year of manufacture: 2006 Output: approx. 800 pcs/h Number of molds in the machine: 2 x 5 L (48 mm cap) Oven dimensions: - Length: 900 mm - Width: 900 mm - Height: 1200 mm Blow molder dimensions: - Length: 1800 mm - Width: 750 mm - Height: 2000 mm Fodjugu E Rspfx Al Uspn Set weight: 1200 kg Technical condition: used machine

Condition: used, Year of construction: 1992, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 4 S1 Year of prod. 1992 Capacity: 4,000 for 1.5 L / 2 L bottles Installed power: 150 kW Includes 1.5 L molds Preform feeder Technical condition: used machine, starts up, program is functional Fpsdpfjwa Rhrox Al Usn

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, machine/vehicle number: 271/1, overall weight: 700 kg, Semi-automatic PET bottle blowing machine for producing 5-gallon PET bottles. Includes heating and blowing unit. Supplied with 2 sets of 5-gallon blowing molds. Fedpfxszd Tduo Al Uopn Capacity: 60 bottles/hour.

Condition: good (used), Year of construction: 1976, wire diameter range: a) single wire: 2,2 - 3,8 mm b) double wire: 2,2 - 3,4 mm nail length: 10 - 80 mm output: 300/600 nails/min. Fsded Im Nuspfx Al Ujpn

Condition: good (used), Manufacturer: Plastik-Maschinenbau GmbH (PM) Model: PM Wiska 30-25 D Serial No.: M0793 Made in: West Germany (Kelberg / Eifel) Type: Single-screw plastic extruder Fpodjxu E E Sepfx Al Ujn Documentation: Included (original German manual and correspondence from 1987) Condition: Used, but complete and fully functional Location: Ivanka pri Nitre, Slovakia Technical Details (approximate) Screw diameter: 30 mm L/D ratio: 25 D Main drive motor: Lenze GFOT 100-24 (440 V / 26 A / 2 kW / 3000 rpm) Power supply: 3 × 380–420 V / 50 Hz Control voltage: 220 V Cooling system: Air-cooled barrel with heating zones Control cabinet: Included, equipped with relays, circuit breakers, and analog meters Description Compact single-screw extruder for laboratory or small-scale production, manufactured by Plastik-Maschinenbau GmbH in West Germany. Designed for processing thermoplastics, material testing, or small extrusion lines (e.g., tubing, profiles, or coating applications). Supplied with the original electrical cabinet, pressure gauge, and documentation. Mechanically and electrically complete; ready for standard commissioning.

Condition: used, Stretch blow molding machine by Etek Fodpfx Alokucxls Ujpn ISBM line = Injection stretch blow molding Stretch blow molding machine for single-use PET bottles made from PET preforms Stretch blow molding machine for production using the rotary process Manufacturer: ETEK / GF-Industries, Type Supra 800 sv 1 Serial number: 22000225 Year of manufacture: 2012 Power: 90 kW Mains connection: 400 volts, 50 Hz Weight: approximately 6000 kg In like-new condition

Condition: excellent (used), Year of construction: 2021, XYZ RMX 3500 3 Axis CNC Bed Milling Machine ProtoTRAK RMX Control YOM 2021 Spindle: 5HP – Programmable 40 – 5000rpm 2 Ranges 40 – 600 & 300 – 5000rpm ISO40 Quill Dia 105mm Table: 1370 x 355mm 4 0ff T Slots T Slot size 15.9mm Max load 600kgs Travel: X – 787mm Fpedpfx Alsx D Tbms Uen Y – 508mm Head Vertical (Z) – 500mm Quill (Z) 127mm Dims without travel – 1905 x 2069 x 2225mm Dim with travel – 2758 x 2869 x 2490mm Weight 2430Kgs Power Requirements 22A Air Requirements 6bar YOM 2021 For Sale with Jet Machinery Ltd Jet Machinery Stock Number: #78900 Machine Serial Number: RM310097 £35,000.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: used, Year of construction: 1999, - PET-Blow moulding machine, make Sidel, type: SBO 16 with preform tipper, preform feed, unscrambler, preform transport, built 1999, already dismantled, ex location for sale. - PET-Blow moulding machine, make Sidel, type: SBO 20, with preform tipper, preform feed, unscrambler, preform transport, built 1999, already dismantled, ex location for sale. Fjdpfxorazwrs Al Ujpn

Condition: used, Year of construction: 2006, Semi-automatic PET bottle machine – ZENTRONIK ZR-7 1. Heating oven for PET preform heating 2. Semi-automatic PET bottle production machine Mould: double-cavity for 5.0L bottles (48 mm cap) Fedpfx Alswnzdaj Uepn Output: approx. 800 bottles/hour Technical condition: used, operational

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, ID BYP01 We sell a used Chinese - PP melt-blown fabric extrusion line for melt blown, make: Zhangjiagang Sevenstars Machinery Co., Ltd., MFG 2020. It was used for a short time. excellent condition. All EU import duties have been paid. Output max 400 kg per 24 hours. General description: 1. Product size: PP melt blown fabric with width at 600mm (after trimming 17m*3) 2. Main Material: PP compounding material 3. Extruder type: SJ65/33 single screw extruder 4. Output capacity: 350-400kg/24hour 5. Electric power supply: 3phase, 380V; 50Hz 6. Additional equipment: • Vacuum feeder • Raw material dryer • Mesh manual filter • T-mould for melt blown fabric • Static electrical discharge equipment • Belt type forming 850mm • Collecting device • Winder and slitting Model L/D Output Speed of Screw Rotationl Power Center Height SJ-65 10-33 80-150kg/h 20-120r/min 18.5kw 1000mm This line contains the following machines: Automacic vacuum loader ZJ-400 and hopper dryer make RHONG model RDM-25, MFG 2020; Single screw extruder, model SJ65/33, MFG 2020; Heating oven for hot air, model HJGF101-4, MFG 2020; Extrusion T-mold, model: SUS630, made in Japan, MFG 2020; Forming device, MFG 2020; Winder & slitting system, MFG 2020; Oil free air compressor, MFG 2020; Fpodpfx Alsuiq Dhj Usn The PP melt blown nonwoven production line is a polymer melt extruded from a screw extruder. The polymer is extremely stretched by high-speed hot air or other means to form very fine short fibers, which are aggregated to A web is formed on a roller or a screen curtain, and is finally reinforced by self-adhesion or thermal bonding. Its unique properties are widely used in mask filter materials, thermal insulation filling materials, medical health materials, wiping materials, etc. The finished product can pass the N95 standard as the core material of the mask. Process of melt blown nonwoven production line Polymer preparation --- Melt extrusion --- Metering pump --- Melt blown die head assembly --- Solution thin-flow drawing --- Fibber cooling --- Auxiliary network --- Electrostatic electret --- Reinforced finished product. Melt-blown cloth is produced by melt-blown process. The equipment mainly includes: screw extruder, melt pump, screen changer, melt-blown device, winding device, air system (hot air blower and heater), etc. The function of the screw extruder is to melt the slice material; the role of the melt pump is to accurately measure, control the output and the fineness of the fiber, and continuously and evenly transfer the melt to the spinneret. The function of the screen changer is to filter out impurities in the melt so as not to block the spinneret holes. The function of the winding device is to pack the melt blown cloth into rolls. The function of the air system (hot air blower and heater) is to provide the temperature and pressure of the hot air used in the drawing of the spinning air stream. Price Euro 39.200 Euro + VAT, negotiable, FCA: Oradea / Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Year of construction: 2014, condition: ready for operation (used), functionality: fully functional, X-Floc EM400/440 Insulation Blowing Machine Professional high-performance blowing machine designed for processing a wide range of loose insulation and fibre materials. Suitable for open blowing, dry injection, damp-spray applications and material conveying, it can be used both on construction sites and as part of a stationary production system. The machine is equipped with a large loading hopper of approximately 1,000 litres, capable of holding around 5–6 standard bags of insulation material. Four rotating shredder shafts progressively break up and condition the compacted fibres before transferring them into the rotary airlock. The adjustable airlock feed gate allows precise control of the material flow. Depending on the version and material used, the EM400/440 can reach a processing capacity of up to approximately 1,600 kg/h. The adjustable air system delivers a maximum pressure of 540 mbar, with an air volume of approximately 100–430 m³/h for the EM400 and up to 100–680 m³/h for the EM440. Main features: Suitable for different insulation and fibre materials Fpjdezlggxjpfx Al Uon Two-stage material conditioning system Four high-speed shredder shafts Approx. 1,000-litre loading hopper Adjustable material flow with 10 feed-gate positions Low-dust loading system with transparent strip curtains Connection for external dust extraction Remote adjustment of air and material parameters Robust, low-maintenance industrial construction Easy access to internal components for servicing Direct NW 76 mm hose connection Suitable for mobile or stationary applications The machine can be operated using a cable or optional wireless remote control, allowing the operator to adjust air output, material supply and pressure-control functions directly from the working area. Technical data: Processing capacity: up to approx. 1,600 kg/h Maximum pressure: 540 mbar Hopper volume: approx. 1,000 litres Shredder shafts: 4 Dimensions: approx. 1,285 × 1,000 × 1,800 mm Filling height: approx. 1,250 mm Hose outlet: NW 76 mm EM400 power: approx. 7.5 kW EM440 power: approx. 10.5 kW Weight: approx. 425 kg for EM400 / 445 kg for EM440 Maximum conveying height: approx. 20–45 m for EM400 / 20–60 m for EM440 Optional equipment may include a wireless remote control, pressure-relief valve, internal or external air amplifier, suction drum and dust-extraction system.