Used Test Station for sale (344)

Condition: used, Test console, test station, measuring station, test device, measuring instrument, tester for HV, PE, and IS measurements ELABO Type PE/IS/HV SCT 42 / 91-3J.3 + 90-1V + 90-9B.3ZM92510 High-voltage tester The PE/IS/HV SCT 42 / 91-3J.3 is used for testing dielectric strength, insulation resistance, and protective earth voltage drop in accordance with VDE0113 or IEC regulations per EN60204, Part 1. Serial No.: 0064016 Year: 2004 Rated voltage: 230 VAC Rated frequency: 50 Hz Rated current: 6.3 A - Protective earth resistance measurement - Insulation resistance measurement - Protective earth voltage drop measurement The 90-1V unit provides a highly stable DC voltage with low ripple. One output terminal supplies the high voltage, while the other is near earth potential and can be set to a potential of up to 300 V. Device No.: 90-7WZ006 Year: 2000 Mains voltage: 230 VAC Mains frequency: 50 Hz Rated current: 1 A Interference suppression: according to VDE 0871 Rated power: 14 watts Output voltage: 0 - 6.0 kV DC Output current: 0 - 2 mA Connection unit for ELABO testers, switching matrix, connector unit ELABO Type 90-9B.3ZM92510 Serial No.: 0097588 Year: 2009 Rated voltage: 230 VAC Rated frequency: 49 - 61 Hz Rated current: 1 A Number of test points: 5 - Compact unit on mobile frame - Various connection cables and accessories as shown Overall dimensions (L x W x H): 580 x 700 x 1380 mm Total weight: 100 kg Pedpfx Asf Axn Aob Uogi Good condition Many other ELABO devices under stock numbers 57819, 57820, and 57821

Condition: used, Test bench, test station, measuring station, test device, measuring device, tester for HV, PE, and IS measurement ELABO Type PE/IS/HV / 91-3J.3 + SHV 16 / 90-1V.3 + 90-9B.3ZM92510 High voltage test device The device PE/IS/HV / 91-3J.3 is used for testing dielectric strength, insulation resistance, and protective conductor voltage drop in accordance with VDE0113 or IEC regulations according to EN60204, Part 1. Serial no.: Year of manufacture: 2003 Rated voltage: 230 VAC Rated frequency: 50 Hz Rated current: 6.3 A - Protective conductor resistance measurement - Insulation resistance measurement - Protective conductor voltage drop measurement The device SHV 16 / 90-1V.3 provides a highly stable DC voltage with minimal ripple. One output terminal supplies high voltage, the other output terminal is close to earth potential and can be set to a maximum potential of 300 V. Serial no.: Year of manufacture: 2005 Mains voltage: 230 VAC Mains frequency: 50 Hz Poded Dc Unepfx Ab Uegi Rated current: 1 A EMI suppression according to VDE 0871 Rated output: 14 watts Output voltage: 0 - 6.0 kV / DC Output current: 0 - 2 mA Connection unit for ELABO tester, switching matrix, connector unit ELABO Type 90-9B.3ZM92510 Serial no.: 0063475 Rated voltage: 230 VAC Rated frequency: 49 - 61 Hz Rated current: 1 A Number of test points: 5 - Compact unit on roller frame - Various connection cables and accessories as shown Overall dimensions (L x W x H): 580 x 700 x 1460 mm Total weight: 100 kg Good condition Many other ELABO devices under stock numbers 57820 and 57821

Condition: excellent (used), Here we offer you a DÜRR test station for adhesive heads. DÜRR test station for glue heads included (5 robot guided glue heads) DÜRR test station (self-built Dürr) for the automotive industry Weight: 1200 kg Type: DÜRR test station for glue heads Condition: used / used Pedpfx Abemhftde Ujgi Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: excellent (used), functionality: fully functional, Universal testing machine for material testing / material inspection Testing of tensile strength, bond tensile strength, and shear strength of masonry & wood joints, and similar applications. - Nail pull-out test - Compression test on cement and mortar prisms - Flexural test on cement and mortar samples - Compaction test - Flexural test on wood, concrete Pjdsxmv H Rjpfx Ab Uegi - Shear strength test on wood - Splitting tensile strength test on wood - Scaffold connection test - Shear strength test on masonry - Tensile test on masonry - Tensile test on reinforcing steel - Tensile test on wood - Pull-out test on reinforcing steel - Reverse bending test on reinforcing steel - Dowel pull-out test - Adhesion tensile test I have made a video demonstrating the machine's operation. I can send this video to a mobile number via WhatsApp or Signal!

Condition: used, Concrete sample press for concrete and material testing Flexural strength test Pgodpfx Asxb Nv Ujb Uoi Determination of compressive strength

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, wheel diameter: 400 mm, overall weight: 4,000 kg, distance between centers: 550 mm, spindle speed (max.): 3,000 rpm, controller model: Siemens 840 D, TECHNICAL DETAILS Max. wheel diameter: 400 mm Workpiece diameter: 36–400 mm Centre distance: 135–290 mm Max. spindle speeds (infinitely variable): 3,000 rpm Centre width: 100–550 mm MACHINE DETAILS Pgsdpfxjywg Hxe Ab Uoi Control: CNC Siemens 840 D Dimensions & Weight Space requirement: approx. 2,000 x 3,055 x 2,788 mm Machine weight: approx. 4,000 kg EQUIPMENT Single-flank rolling test Double-flank rolling test Structure-borne noise testing Helical contact testing (double-flank contact) Use of up to 6 test carriages Highest test accuracy and repeatability Machine table with workpiece drive Swivelling pneumatic unit Spray lubrication (Type: Vogel) Oil mist extraction (Type: Elbaron)

Condition: good (used), Year of construction: 2007, max. wheel diameter 500 mm gear width 200-400 mm module 12 turning speeds 0-3250 U/min bracke pressure bis max. 95 Nm inner taper Konus #39 Control Fanuc 16 Psdpfx Aevr Hf Eob Usgi total power requirement 15 kW weight of the machine ca. 6 t dimensions of the machine ca. 2.350 x 2.240 x 2.500 mm HIGHLY FLEXIBLE TESTING OF HARD, FINISHED AND GREEN SPIRAL BEVEL AND HYPOID GEAR SETS The T 60 bevel gear testing machine is a CNC testing machine with three linear axes for the fully automatic hard and soft testing of spiral bevel and hypoid gear sets with a 90° axis angle. It offers versatile objective and subjective testing options with speeds up to 3,250 min and braking torques up to max. 95 Nm.

Condition: good (used), Year of construction: 2002, Clampable cutter head type (max.) 460 mm Cutter head weight (max.) 150 kg Mounting disc diameter for cutter heads (Ø) 360 mm Mounting cone for cutter heads Nominal diameter Ø 58,227 mm travel -z axis 200 mm diagram-drawing enlargement ±10 - ± 500 µm weight of the machine ca. 2,3 t dimensions of the machine ca. 2 x 1,5 x 2,03 m In the manufacturing process for spiral-toothed bevel gears, the quality of the gear cutting gear cutting tools used plays a decisive role. Particularly in high gear cutting quality and a long service life can only be achieved with precisely can only be achieved with precisely adjusted cutterheads. The Oerlikon cutterhead setting and testing device CS 200 enables quick and easy setting of the individual knives and simple adjustment of the individual knives, it checks the position and documents the measurement results. The measuring sequence on the CNC-controlled testing device is partially automated: The individual actions for carrying out the actions for carrying out the sequence are displayed on the screen via the operator guidance. The positioning of the individual knives in the cutter head and the height of the knife tips is largely automatic thanks to a special sequence and is simultaneously documented by means of a run-out diagram. A subsequent measuring sequence checks the radial position of the inner and outer cutting edges of all knives in the cutterhead. If individual test parameters on the knives do not correspond to the the tolerance specifications, this can be individually repositioned. The combination of semi-automated setting sequence, operator-guided set-up actions and automatic operator-guided set-up actions and automatic measuring sequence, cutterheads can be can be set conveniently, quickly and with high precision. Operator-guided setting and test sequence - Graphic display of the cutter head design and the measurement results with tolerance check - Instructions for the operator in plain text Instructions for the operator in plain text (without coded information) - Simple assignment of the measurement results to the knives - Documentation of the setting and measurement results via printer- Setting and test sequence suitable for ARCON®, RSR, Spirapid, SPIRON®, TRI-AC® types - Interface for neutral data Pgsdsw N S E Ajpfx Ab Uji

Condition: used, Year of construction: 2011, machine/vehicle number: 25621, workpiece diameter (max.): 360 mm, Equipped with: Gear Spindle Runout: -Radial (Bore): .00005 -Axial (Face): .00005 Pinion Spindle Runout: -Radial (Bore): .00005 Axial (Face): .00005 Axis Repeatability: -X: .0001 -Y: .0001 -Z: .0001 Axis Lost Motion: -X: .00005 -Y: .00005 -Z: .00005 Fanuc 160I MB Control Base Work Holding Draw Bars Automatic Doors Spindle Chiller Transformer Hydraulic System Festo Pneumatics Automation Interface Available SPECIFICATIONS: Maximum Gear Outside Diameter: 360 mm (14.2") Maximum Pinion Outside Diameter: 340 mm (13.4") Maximum Pinion Drive Speed: 3000 rpm Maximum Gear Drive Speed: 1500 rpm Offset Vertical 150 mm ( 5.9") Pinion Cone Range: (90) (135-350) (70) (146-438)* (110) (51-343)* Gear Cone Range: (90) (65-280) (70) (78-306)* (110) (56-284)* Standard Testing Torque Load 2 to 90 Nm (1.5 to 66 ft-lb). Parallel Axis - face-to-face 147 - 362 - Center Distance -7 - 250 Pinion Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 419 mm (16.5") Gear Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 250 mm (9.8") Floor Space (width & length) 2100 x 2550 mm (82.7 x 100.4") Height (to top of stack light) 2750 mm (108.3") Pedpfoxdfansx Ab Ujgi Weight (base machine) 9100 Kg (20062 lbs)

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Pgodpsrtrzdefx Ab Usi Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Depth of Taper: 8" Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Condition: used, Year of construction: 1991, max. wheel diameter --- mm gear width --- mm Podpfx Aboya Eqao Ujgi max. module --- min. module --- Control --- total power requirement --- kW weight of the machine ca. --- t dimensions of the machine ca. --- m

Year of construction: 2022, condition: good (used), Test stand for filter testing, filter testing, filter test system, filter measurement system, filter test system -Manufacturer: Lorenz, Filter Test System Type FMP 03 with accessories -Filter holder: Type FH 143/149 -Accessory case: with extensive contents -Individual components/accessories: see photos -Dimensions: 600/560/H975 mm / 640/460/H1130 mm / 430/340/H125 Pgjdpfx Asyk Ahwjb Usi -Weight: 146.3 kg

Condition: excellent (used), Vötsch Climate Test Chamber VT 4004 Tabletop Test Cabinet -40°C to +180°C For sale is a high-quality climate test chamber / tabletop test cabinet by the renowned manufacturer Vötsch Industrietechnik (Model VT 4004). This device is ideal for use in laboratories, R&D, or industrial settings and is perfectly suited for the simulation of temperature conditions when testing electronics, components, and materials. Functions & Application Areas: - Temperature testing in the range from -40°C to +180°C - Uniform temperature distribution via recirculating air system - Combination of cooling and heating - Digital control with display - Compact tabletop design (approx. 35-liter interior) - RS232 interface for connection to PC or measurement systems Technical Data: Pjdpfx Aoywg Amsb Ujgi Manufacturer: Vötsch Industrietechnik Type: VT 4004 Volume: approx. 35 liters Cooling: air-cooled Refrigerant: R404A Electrical Data: Voltage: 1/N/PE AC 230V ±10% / 50 Hz Rated power: approx. 1.5 kW Rated current: approx. 7.5 A Dimensions: External: Width: 95 cm, Height: 63 cm, Depth: 83 cm Interior: Width: 32 cm, Height: 40 cm, Depth: 27 cm Condition: used Scope of delivery: (please see photo) (Specifications and details subject to change and error!) For further questions, please feel free to contact us by phone.

Condition: used, table clamping surface: 228 x 273 mm 3 T-slots: 12 mm in between 4 x 4 threaded holes: M 8 table height at zero position: 146 mm Pgjdpfx Asbbgcxeb Usi Space requirement: 250 x 290 mm Weight: 41 kg

Condition: excellent (used), Pfeiffer Pfeiffer Vacuum HLT 560 Helium Leak Detector Professional Leak Testing, Sniffer & Vacuum Modes Description: For sale is a professional helium leak detector, Pfeiffer Vacuum HLT 560. The device is designed for highly precise leak testing with helium and is typically used in industry, manufacturing, quality assurance, laboratories, as well as in technical service operations. It is suitable for the reliable detection of even the smallest leaks. The HLT 560 operates mass spectrometrically and can be used in both vacuum and sniffer modes. With the sniffer probe, leak points can be precisely located, while in vacuum mode, complete assemblies or systems can be tested. Application areas (examples): - Leak testing of components and assemblies - Testing of vacuum chambers, pipelines, valves, heat exchangers - Quality control in production - Service and maintenance of vacuum technology systems Technical Data: Manufacturer: Pfeiffer Vacuum Model: HLT 560 Pgodpfsyaxu Sex Ab Uji Test gas: Helium Measurement principle: Mass spectrometric helium leak detection Operating modes: Vacuum mode / Sniffer mode Reference leak rate: (7.4 ±15%) × 10⁻⁷ mbar·l/s Dimensions (approx.): Height: 110 cm Width: 50 cm Depth: 60 cm Interfaces: RS232, RS485, Relay I / II, Gauge connection Power supply: 230 V / 50 Hz Power consumption: approx. 400 VA Weight: approx. 44 kg Condition: used Scope of delivery: (see photo) (Subject to changes and errors in technical details, all information is without guarantee!) For further questions, please feel free to call us.

Condition: used, Type: Erichsen 606/1000L For sale is a high-quality Erichsen 606/1000L corrosion testing system. This unit is ideal for performing salt spray and condensation tests to evaluate the corrosion resistance of coatings, metals, and surface materials. Standards & Application Areas: Suitable for tests according to DIN EN ISO 6270-2, DIN 50958, ISO 11503, ASTM D2247, BS 3900 Part F2, and ISO 9227. Pgedoxdcqwjpfx Ab Uji Perfect for quality control, research & development in the automotive, coating, and metal industries. Technical Data: Test chamber volume: 1000 l Capacity: approx. 180 test specimens Test temperature range: ambient temperature up to +50 °C Power supply: 400 V / 3~ / 50 Hz Power consumption: approx. 4320 VA Air connection: 4–10 bar, approx. 15 l/min at 6 bar Water connection: 2–6 bar Dimensions (W×D×H): approx. 1820 × 1000 × 1900 mm Weight: approx. 150 kg Condition: used Scope of delivery: (see picture) • Test chamber (1000 l) • Dosing unit for spray solution • Air circulation pump (Subject to technical modifications and errors in data and specifications!) If you have any further questions, we are happy to assist you by phone.

Condition: excellent (used), CTS Type: C-40/350 Air-cooled Climate Test Chamber For sale is a professional CTS climate test chamber, model C-40/350. This device is designed for demanding environmental simulations in industrial applications and is ideal for material testing, electronics, automotive, aerospace, and research. Temperature Testing: - Temperature range: -40°C to +180°C - Temperature deviation: ≤ ±0.3 K over time - Temperature change rate according to IEC 60068-3-5: - Heating: 3.5 K/min - Cooling: 4 K/min - Heat compensation: - Approx. 3500 W at +20°C - Approx. 2000 W at -20°C Climatic Testing: - Temperature range: +10°C to +90°C - Humidity range: 10% to 95% relative humidity - Dew point range: +5°C to +78°C - Temperature deviation: ≤ 1.0 K over time - Humidity deviation: ≤ ±3.0% r.h. over time Technical data refer to an ambient temperature of +25°C, nominal voltage 400V, without test specimen, without heat compensation, and without additional accessories. Options may influence performance data. Technical Specification: - Refrigeration unit: Air-cooled, low-noise, fully hermetic, infinitely variable performance adjustment via electronic monitoring and control system, environmentally friendly refrigerant R404A - Test chamber floor load: 150 kg/m² - Shelf: Stainless steel, support surface 620 x 600 mm - Maximum load per shelf: 35 kg - Total load with maximum number of shelves: 100 kg Control: - 32-bit controller - LCD control panel - Digital display of setpoint and actual values - Numeric entry of setpoints - Plain-text error messages - RS 232 interface - Ethernet interface - Free switching channels for external test sample control Dimensions: - Test volume: 350 liters - Internal dimensions: Height 750 mm × Width 650 mm × Depth 720 mm - External dimensions: Height 1800 mm × Width 920 mm × Depth 1670 mm Operating Data: - Electrical connection: 400V 3/N, 50 Hz - Rated power: 7.1 kW - Rated current: 11.5 A - Protection class: IP 54 - Sound pressure level: Pgjdpex Ekupofx Ab Uji

Condition: excellent (used), Here we offer you a Heraeus Vötsch temperature test chamber. Heraeus Vötsch temperature test chamber water cooled Temperature range -70°C to + 180°C Temperature deviation temporal ±0,1 to ±0,5 K Temperature deviation in time ±0.5 to ±2.0 K Temperature change rate cooling 7.5 K/min Temperature change rate heating 7.5 K/min Heat compensation +20°C 3000 W Heat compensation -20°C 3000 W Test chamber dimensions: Width 580 mm Depth 450 mm Height 750 mm Outer dimensions: Width 870 mm Depth 1280 mm Height 1575 mm Pgsdpfxehh H His Ab Uji Observation window: Width 300 mm x height 540 mm Test chamber volume 190 litres Rated voltage: 3/N/PE AC, 400 V ±10 %, 50Hz Rated power: 10.5 kW Rated current: 22 A Fuse, on-site: 32 A slow-blow Sound level at 1m distance (free field measurement) < 69dB (A) lateral feed-through 50 cm / 125 cm Cabinet is water cooled Refrigerant: R 404A and R 23 Weight approx. 460 kg Type: VTS 7018-5 For you as a buyer for safety the following information! The following points are carried out on our offered chambers in advance: 1. function check and exchange of necessary components 2. new filling with legally compliant refrigerant 3. after successful inspection, the chambers are subjected to a test run, which is monitored with calibrated equipment. Condition: used / used Scope of delivery: (See picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer gladly on the phone for you.

Condition: excellent (used), Heraeus Vötsch Type: VTS 7018-5 Heraeus Vötsch Temperature Test Chamber, Water-Cooled Temperature range: -70°C to +180°C Temporal temperature deviation: ± 0.1 to ± 0.5 K Spatial temperature deviation: ± 0.5 to ± 2.0 K Temperature change rate (cooling): 6.5 K/min Temperature change rate (heating): 7.5 K/min Heat compensation: 4,500 W Test chamber dimensions: Width 580 mm x Depth 450 mm x Height 750 mm External dimensions: Width 870 mm x Depth 1,280 mm x Height 1,575 mm Viewing window: Width 300 mm x Height 540 mm Test chamber volume: 190 liters Rated voltage: 3/N/PE AC, 400V ±10%, 50Hz Rated power: 10 kW Rated current: 21 A Supply-side fuse: 32 A slow-blow Sound level at 1 m distance (free-field measurement): < 63 dB(A) Lateral port: 50 cm / 125 cm Chamber is water-cooled Refrigerants: R452A and R23 Weight: approx. 460 kg Important safety information for buyers: The following procedures are carried out on all chambers offered by us: 1. Functional check and replacement of necessary components 2. If required, refilling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, all chambers are subjected to a documented trial run. Condition: used Scope of delivery: (see photos) (Technical data and specifications subject to change and errors!) If you have further questions, we are happy to provide information by phone. Pedpfx Asyu Rhgeb Usgi

Year of construction: 2011, condition: good (used), Glass plate 6 cameras with illumination Two hoppers + one drive unit Integrated supply bunker 25 L / 50 kg with control unit Pgedpfeyu Ivnsx Ab Uji Skako Bunker 125 Loader for 10 crates Extra lens TC1224 + holder Extra lens TC23056 + holder without UPS

Condition: excellent (used), CTS CW‑60/5.5 – Water-Cooled Climate Test Chamber The CW‑60/5.5 from CTS GmbH (Climatic Test Systems) is a mid-sized, walk-in or drive-in climate chamber designed for conducting temperature and humidity tests on multiple test specimens simultaneously. Equipment Description This climate test chamber allows you to assess the function or material properties of test objects under controlled temperature and humidity conditions. Efficient air circulation with a high re-circulation rate ensures excellent transfer to the test goods. The air handling system is located at the rear of the inner chamber. All of the aggregates are mounted in a separate frame behind the unit, providing easy access. The control system is housed in a separate switch cabinet, while the user interface is integrated into the cabinet door. To dehumidify the test chamber, it is equipped with a self-regenerating compressed air dryer. Fresh air can be supplied by a blower to purge the chamber as required. Technical Specifications: Temperature Testing: - Temperature range: -60 °C to +100 °C - Temperature deviation: ±0.5 to 1 K over time - Temperature change rate (linear with test specimen and radiant heat, measured at supply air): - Heating: 2 K/min from -40 °C to +85 °C - Cooling: 2 K/min from +85 °C to -40 °C Climatic Testing: - Temperature range: +10 °C to +90 °C - Humidity range: 10% to 95% relative humidity (dew point range +5°C to +89 °C) - Temperature deviation: ±0.5 K over time - Humidity deviation: ±1 to ±3 % r.h. over time Technical data based on ambient temperature of +25 °C, rated voltage 400 V, without test specimen, without radiant heat, and without additional equipment. Dimensions: Internal dimensions (test/useable space): - Volume: approx. 5,500 liters (5.5 m³) - Internal dimensions (approx.): Height 2300 mm, Width 1600 mm, Depth 1550 mm External dimensions: - Height 2800 mm, Width 2250 mm, Depth 5000 mm Operating Data: - Electrical connection: 400 V +6/-10%, 3/N, PE, 50 Hz - Rated power: 58.3 kW (incl. 5 sockets) - Rated current: 86.0 A - Protection category: IP 54 Technical Design: - Refrigeration unit: water-cooled, low-noise, semi-hermetic, stepless power adjustment via electronic monitoring and control system - Environmentally friendly refrigerants: R 23 / R 404 A Pedpfjx Eabpsx Ab Usgi Notes: - Inspection possible by appointment (46325 Borken) - Shipping by freight forwarding possible – costs & organization on request - Scope of delivery: (see picture) - (Subject to modifications and errors in technical data, all information provided without guarantee!) For further questions, we are happy to assist you by phone.

Condition: excellent (used), CTS CW-60/5.5 – Water-cooled Climate Test Chamber The CW-60/5.5 from CTS GmbH (Climatic Test Systems) is a medium-sized, walk-in and drive-in climatic chamber designed for simultaneous temperature and humidity testing on multiple test specimens. Device Description The climate test chamber allows for functionality or material property testing of a test item under the influence of temperature and humidity. Efficient air circulation with a correspondingly high level of recirculating air volume ensures excellent transfer to the test item. The air treatment compartment is located at the rear of the test chamber. The aggregates are positioned behind the unit in a separate frame for easy access. The control system is integrated into a separate control cabinet. The control panel is mounted in the door of the control cabinet. For dehumidification, the test chamber is equipped with a self-regenerating compressed air dryer. The test chamber can also be purged with fresh air via an internal blower. Technical Specifications: Temperature Testing: - Temperature range: -60 °C to +100 °C - Temperature deviation: ±0.5 to 1 K over time - Temperature change rate, linear with specimen and heat radiation, measured in supply air: - Heating: 2 K/min from -40 °C to +85 °C - Cooling: 2 K/min from +85 °C to -40 °C Climatic Testing: - Temperature range: +10 °C to +90 °C - Humidity range: 10% to 95% rH - Dew point range: +5 °C to +89 °C - Temperature deviation: ±0.5 K over time - Humidity deviation: ±1 – ±3% rH over time Technical data refer to an ambient temperature of +25 °C, nominal voltage 400 V, without test item, without external radiation and without additional devices. Dimensions: Internal dimensions (test space/usable volume): - Volume: approx. 5,500 liters (5.5 m³) - Internal dimensions (approx.): Height: 2,300 mm, Width: 1,600 mm, Depth: 1,550 mm External dimensions: Height: 2,800 mm, Width: 2,250 mm, Depth: 5,000 mm Operating Data: - Electrical connection: 400 V +6/-10%, 3/N, PE, 50 Hz - Nominal power: 58.3 kW (incl. 5 sockets) - Nominal current: 86.0 A - Protection rating: IP 54 Technical Execution: Refrigeration unit: Water-cooled, low noise, semi-hermetic, infinitely variable capacity adjustment via electronic monitoring and control system, environmentally friendly refrigerants R 23 / R 404 A Notes: Inspection by appointment possible (46325 Borken) Shipping by forwarding agent possible – Costs & organization upon request Podpfx Abox Eaxbo Ujgi Scope of delivery: (see photo) (Subject to change and possible errors in the technical data; information provided without liability!) For further questions, we are happy to assist you via telephone.

Condition: excellent (used), CTS CW-60/5.5 – Water-cooled Climatic Test Chamber The CW-60/5.5 by CTS GmbH (Climatic Test Systems) is a medium-sized, walk-in or drive-in climate chamber for conducting temperature and humidity tests on multiple test specimens simultaneously. Device Description The climatic test cell enables testing of the functionality or material properties of a specimen under the influence of temperature and humidity. Optimized air circulation with a high recirculation rate ensures effective climate transfer to the test specimen. The air conditioning compartment is located at the rear of the interior chamber. The units are housed in a separate frame behind the main device and are easily accessible. The control system is installed in a separate control cabinet, and the control panel is integrated into the cabinet door. For dehumidification, the test cell features a self-regenerating compressed air dryer. Fresh air can be flushed into the test chamber using a fan. Technical Specifications: Temperature Tests: - Temperature range: -60 °C to +100 °C - Temperature deviation: ±0.5 to 1 K over time - Temperature change rate, linear with specimen and radiant heat, measured in supply air: - Heating: 2 K/min from -40 °C to +85 °C - Cooling: 2 K/min from +85 °C to -40 °C Climatic Tests: - Temperature range: +10 °C to +90 °C - Humidity range: 10% to 95% r.H. - Dew point range: +5 °C to +89 °C - Temperature deviation: ±0.5 K over time - Humidity deviation: ±1 to ±3% r.H. over time Podpfxjx D Abps Ab Uogi The technical data refer to an ambient temperature of +25 °C, nominal voltage 400 V, without test specimen, no radiant heat, and without additional equipment. Dimensions: - Interior (Test chamber / usable space): - Volume: approx. 5,500 liters (5.5 m³) - Internal dimensions (approx.): Height: 2300 mm, Width: 1600 mm, Depth: 1550 mm - External dimensions: Height: 2800 mm, Width: 2250 mm, Depth: 5000 mm Operating Data: - Electrical connection: 400 V +6/-10%, 3/N, PE, 50 Hz - Nominal power: 58.3 kW (incl. 5 sockets) - Nominal current: 86.0 A - Protection class: IP 54 Technical Design: - Refrigeration unit: water-cooled, low-noise, semi-hermetic - Infinitely variable capacity adjustment via electronic monitoring and control system - Environmentally friendly refrigerants: R 23 / R 404 A Additional Information: - Inspection possible by arrangement (46325 Borken) - Shipping by freight carrier is possible – costs & arrangements upon request - Scope of delivery: (see picture) - (Changes or errors in technical data reserved) - For further questions, we are happy to answer your call.

Condition: excellent (used), Here we offer a Feutron climate test chamber. Feutron Climate Test Chamber Temperature Temperature range: -40...90°C Climatic range (without heat load): 10...85°C Temporal temperature deviation during temperature operation: ≤ ± 0.5 K/min Temporal temperature deviation during climatic operation: ± 1.0... ± 1.5 K/min Change rates Heating: avg. 2.0 K/min Cooling: avg. 2.0 K/min Standard IEC 1646 is achievable with testing, solar modules up to max. 160kg weight and nonlinear ramps (setpoint jump) Drying Air drying: condensation drying Humidity Air humidification: steam humidification Humidity range: 10...95 % r.h. Temporal humidity deviation: ≤ ± 3.0... ±5.0 % r.h. Dew point range: 8...80.9°C Test Chamber Test chamber volume: 7.0 m³ Dimensions Internal dimensions: Width 1500 mm x Height 2250 mm x Depth 2000 mm Swing door DIN right, heated, Width 900 mm x Height 2100 mm Observation window, heated, with blackout shutter and lockable: Width 500 mm x Height 600 mm Feedthrough: 2x, right front side, Ø 75 mm Irradiation unit, test chamber Opening: 4x in left side wall for SC 2500, each 850 x 700 mm Irradiated area when using SC 2500: 1200 x 1200 mm Radiation intensity at 1.0 m wall distance: 1000 ± 10% W/m² Lighting: 1x halogen lamp, 200W Refrigeration system: Bitzer compressor, semi-hermetic, 2-stage, air cooled Condenser: split condenser (outdoor installation, winter control) Refrigerant: R507 / R23 Temperature control system Coolant medium Tyfocor / water Mixing ratio 50/50% Coolant density: 1.072 kg/dm³ Filling quantity: approx. 80 dm³ Pyranometer Temperature range: -40...150°C Max. radiation absorption: 4000 W/m² Spectral range (50% points): 305...2800 nm Sensitivity (nominal): 7 µV/W/m² Power supply, test chamber Mains connection: 400V, 3/N/PE, AC, 50Hz Connection type: hardwired Max. simultaneous power demand: approx. 32.0 kW Supply fuse: 3 x 63, Char C (A) Power supply, SolarConstant Mains connection: 400V, 3/N/PE, AC, 50Hz Connection type: Pedpfx Absklv H Io Uogi Max. simultaneous power demand: approx. 30.0 kW Supply fuse: 3 x 63, Char C (A) Overall external dimensions of the test cell including: equipment room/control cabinet and control cabinet for SolarConstant 2500 External dimensions equipment room: Width 3440 mm x Height 2580 mm x Depth 2950 mm /control cabinet: Width 2200 mm x Height 1830 mm x Depth 1100 mm External dimensions condenser, split: Width 900 mm x Height 950 mm x Depth 2000 mm Weight test chamber (total): approx. 2700 kg Condenser empty weight: 153 kg Weight: 2700 kg Type: 3707/06 Condition: used Scope of delivery: (see picture) (Technical data and information are subject to change and errors!) For further questions, we are happy to assist you by phone.

Condition: excellent (used), Year of construction: 2019, ACS Angelantoni Model: ACS WZH10-4080-2 BT Angelantoni Walk-in Climatic Chamber Pedpeyg I Eyjfx Ab Ujgi ACS WZH10-4080-2 BT Optimized for Battery Testing (Li-Ion) -40°C to +80°C Description: For sale is a walk-in climate and environmental test chamber from the renowned manufacturer Angelantoni Test Technologies (ACS), model WZH10-4080-2 BT, year of manufacture 2019. The system is designed for demanding industrial, development, and research testing and is equipped with advanced safety features specifically tailored for battery and accumulator testing (e.g., lithium-ion). Special feature: Safety equipment for battery testing: The system is specially equipped for battery and accumulator testing, including: - Pressure relief flap for controlled pressure discharge in the event of a malfunction - Gas detection system for early identification of critical gas concentrations - Aerosol fire suppression system (SalgroMAG) → Ideal for lithium-ion testing Suitable for: - Batteries & accumulators (including lithium-ion) - Electronics & control units - Automotive components - Industrial & research tests - Endurance, aging, and stress tests Technical data (from nameplates & documentation) General: Model: WZH10-4080-2 BT Year of manufacture: 2019 Standards: CE, IEC/EN 60204-1 Design: Walk-in climatic chamber, double-door Test range: Temperature: –40 °C to +80 °C Relative humidity: 10% to 95% RH Electrical data: Supply: 400 V 3-phase + N + PE 50 Hz Rated power: approx. 37 kW Full load current: approx. 115 A Protection rating: IP54 Short-circuit strength: 10 kA Refrigeration system Refrigerant: R452A Charge: approx. 50 kg CO₂ equivalent: approx. 107 t Dimensions: External dimensions (approx.): Length: ~4.5 m Width: ~2.2 m Height: ~2.4 m Weight: approx. 3,800 kg Condition: used Scope of delivery: (See photo) (Technical data subject to change and errors excepted!) We are happy to answer further questions by phone.