Used Testing for sale (10,232)

Condition: excellent (used), Weiss Here we offer a Weiss emission test chamber. Mini - SHED for Diurnal Loss Measurements Test chamber dimensions: Width 1600 mm x Depth 2140 mm x Height 2150 (Usable 1600) mm. Housing dimensions: Width 1760 mm x depth 3100 mm x heights 2790 mm Max. floor load 250 kg Operating range +18 °C ...+45 °C, (at higher temperatures SHED operation is only possible without Tedlar bag) Temperature range +18 °C ...+45 °C Temperature constancy ≤ ±1 K (temporal) Temperature change rate, (heating and cooling) approx. 0.5 K/min., without test material Duct connection (air inlet and outlet) ∅ 80 mm, in chamber rear wall Shut-off valve, gas-tight (air inlet and outlet) ∅ 80 mm, gas-tight, pneumatic operation Delivery limit: connection flange of shut-off valve Bodpfxemfny Ie Aglscu Cooling water consumption approx. 0.8 m3/h Voltage: 230/400 V; 3 PH + N + PE; 50 Hz Rated power: 4,1 kW Rated current: 14,0A Weight: approx. 2500 kg type: WT 5,1'/ + 18-45 Condition: used / used Sale ex location Scope of supply: (Only the Weiss emission test chamber WT 5,1'/ + 18-45 Mini-SHED) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: excellent (used), Heraeus shock test chamber Here we offer a shock test chamber. Temperature shock test chamber water cooled Two-chamber design Bcodoikvlxspfx Agleu Warm chamber: The temperature range of the warm chamber is from +50°C to +220°C. Temperature deviation temporally in useful chamber center ± 1 K Temperature deviation spatially ± 2 K Temperature change rate heating 11 K/min cold chamber: the cold chamber from -65°C to +70°C Temperature deviation temporally in useful space center ± 1 K temperature deviation spatially ± 2 K Temperature change rate heating 2 K/min cooling 3 K/min Test chamber volume 125 liters Temperature range hot chamber +50°C to +220°C Temperature range cold chamber -80°C to +70°C Test chamber dimensions width 470mm depth 650mm height 410mm Outer dimensions width 930mm depth 2115mm height 1970+mm Rated power 10 kW Rated current 25 A Voltage: 3/N/PE AC 400V +6/-10% 50Hz Refrigerant R404A / R23 Weight: 1000 kg For you as a buyer for safety the following information! The following points are carried out on our offered chambers in advance: 1. functional check and replacement of necessary components 2. new filling with legally compliant refrigerant 3. leak test with certificate 4. after successful inspection, the chambers are subjected to a test run, which is monitored with calibrated equipment. Type: HT 7012 S2 Condition: used / used Scope of delivery: (See picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: excellent (used), Weiss temperature test chamber Bcsdjirmg Aopfx Agleu Here we offer a Weiss temperature test chamber. Weiss temperature test chamber water cooled Technical data: Test chamber designation: WT1-600/70 Outer dimensions without hinges and door lock height 1980 mm, width 1085 mm, depth 1655 mm Internal dimensions height 950mm, width 800mm, depth 800mm Test chamber capacity: approx. 600 liters cold / heat operation -70 to 180°C Temperature change per time cooling approx. 2,5 K/min Heating up approx. 4 K/min 3/N/PE AC 400V ±10% 50Hz Rated power: 9.1 kW Rated current: 19 A Permissible test material weight Total load of grate supports 80kg Refrigerant: R 404A +R23 Weight: 600kg Type: WT1-600/70 For you as a buyer for safety the following information! The following points are carried out on our offered chambers in advance: 1. functional check and exchange of necessary components 2. new filling with legally compliant refrigerant 3. after successful inspection, the chambers are subjected to a test run, which is monitored with calibrated equipment. Condition: used / used Scope of delivery: (See picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: excellent (used), RS simulators Here we offer a temperature test cabinet. Temperature test chamber water cooled Temperature range: -70°C to +180°C Time deviation: ±1 K according to DIN 50011 with empty test chamber Average heating time: approx. 3 K/min 8acc. to DIN 50011 part 12) Average cooling time: approx. 3 K/min 8acc. to DIN 50011 Part 12) Test chamber dimensions: Width 530 mm x height 530 mm x depth 530 mm Outer dimensions: Width approx. 900 mm x Height approx. 1800 mm x Depth approx. 1400 mm Total power: approx. 6 kVA power consumption: 12 A Main fuse: 3 x16 A, slow blow Connection voltage: 3x400V/N/PE 50Hz Weight: approx. 600 kg Type: TS 150/75 Refrigerant: R404A / R23 Condition: used / used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) Bcodpfx Aelp Hytoglju Further questions we can answer on the phone for you.

Condition: excellent (used), Vötsch Type: VT 3050 Modules / Test Chamber Temperature Chamber Air-cooled Test chamber capacity 500 litres Temperature range -30°C / +100°C Temporal temperature fluctuation K ±0.5 Spatial temperature fluctuation K ±1.5 Bcjdpfx Asw S E N Tjglsu Temperature gradient K 3 Change rate Heating K/min 2.0 Cooling K/min 1.4 Heat compensation max. W 650 Calibration values +23°C +80°C Test chamber dimensions Width 710 mm Depth 590 mm Height 1250 mm External dimensions Width 940 mm Depth 1030 mm Height 1955 mm Sound pressure level db(A)

Condition: excellent (used), Zwick Type: BT1-FR050TH.A1K 50 kN Universal Testing Machine Zwick/Roell BT1-FR050TH.A1K Material Testing Machine – Precise Strain Gauge Testing Note: PC not included!! Highlights: - Test force: 50 kN (tension/compression) - High-precision TC-MODCSCC module for strain gauge load cells (4- & 6-wire) - Measuring range: 0.2 – 165% of nominal value, data acquisition up to 500 Hz - Maximum resolution: up to 297,000 points (at 50 Hz) - Positioning repeatability: ±10 µm - Crosshead speed: 0.0005 – 600 mm/min - Robust construction - Compact dimensions: 1,814–2,688 mm height, 936 mm width, 722 mm depth - Low noise: 59 dB(A) - Ambient conditions: +10 to +35 °C, humidity 20–90% Special features: - Ideal for research, development, or industrial material testing Dimensions & weight: Load frame: - Test force (tension/compression): 50 kN - Load frame height: 1,714 mm - Overall height: 1,814 – 2,688 mm - Load frame width: 760 mm - Overall width: 936 mm - Load frame depth: 477 mm - Overall depth: 722 mm Bsdpfx Ajw S Hvzeglocu Weight: - With electronic unit: 230 kg - With typical accessories: approx. 300 kg Condition: used Scope of delivery: (see picture) - ZwickRoell BT1-FR050TH.A1K testing machine - Operating manual (Specifications are subject to change and errors excepted!) If you have any questions, we are happy to answer them by phone.

Condition: used, dr. wiesner Type: INTEGRA DDV -1...1 bar Product description: dr. wiesner Integra leak test system The classic - for all common test procedures The leak test system for industrial leak-tightness and flow tests with fully graphical color display up to three independent test circuits operable 255 test programs can be stored automatic process optimization autoTune (option) communication via flexibly exchangeable bus coupling modules freely programmable fixture control freely programmable special test procedures The device is suitable for tests according to the relative and differential pressure method with overpressure. Special versions: none Technical data: Electrical supply: 110 ... 230V~; 50 ... 60Hz (connection via power cable to plug XO) pneumatic: clean and dry compressed air max. 7 bar (to connection P) Test pressure range: 0 ... 1000 mbar, electronically regulated Bsdpfxswqm Dde Agljcu Measuring ranges Relative pressure: 0 ... 1000 mbar Differential pressure: +20 mbar Resolution: 0.1 Pa Internal volume: 13 cm³ test circuit 15.0 cm³ reference circuit Electrical interfaces: 3x serial RS232 (COM1; COM2; COM3) 1x digital I/O (X1) pneumatic: Connection test object (Test) Connection reference circuit (Ref.) Enclosure Protection class: IP40 Dimensions: 450x185x380mm (WxHxD) Weight approx. 15.5kg Condition: used (Changes and errors in the technical data, information reserved!) We are happy to answer further questions by phone.

Condition: used, Technical specifications (manufacturer/model type – without guarantee): Peak force: “according to manufacturer specifications” approx. ≈ 10 kN Bcsdoxtdl Ispfx Aglju Max. acceleration: “up to approx. 1,000 m/s²” Max. speed: “typically in the range of approx. 1 m/s to a few m/s” Components: - Control cabinet TGA 022/3 - Vibration exciter SW 6507 - Power amplifier TG D 9000-000.00 - Blower Condition: used Scope of delivery: Vibration test system as shown (Subject to change and error in technical data!) For further questions, we are happy to answer your call.

Condition: used, Type: Erichsen 606/1000L For sale is a high-quality Erichsen 606/1000L corrosion test chamber. This unit is ideal for performing salt spray and condensation tests to evaluate the corrosion resistance of coatings, metals, and surface materials. Standards & Application Areas: Suitable for testing according to DIN EN ISO 6270-2, DIN 50958, ISO 11503, ASTM D2247, BS 3900 Part F2, and ISO 9227. Perfect for quality control, research & development in the automotive, coatings, and metal industries. Technical Data: Test chamber volume: 1000 l Capacity: approx. 180 test samples Test temperature range: Ambient temperature up to +50 °C Power supply: 400 V / 3~ / 50 Hz Power consumption: approx. 4,320 VA Air connection: 4–10 bar, approx. 15 l/min at 6 bar Water connection: 2–6 bar Dimensions (W×D×H): approx. 1,820 × 1,000 × 1,900 mm Weight: approx. 150 kg Condition: used Scope of delivery: (see photo) Test chamber (1000 l) Bcodpfexdcqwjx Aglju Controller with touchscreen operation Dosing unit for spray solution Air circulation pump (Specifications are subject to change and possible errors!) For any further questions, please feel free to contact us by phone.

Condition: used, IMV Type: i240 + SA3AM Power Amplifier + Fan Dimensions Power Amplifier: SA3AM.i40 W x H x D 1234 x 997 x 720 mm Vibration Exciter: i240 W x H x D 580 x 1950 x 850 mm Technical Data: Armature Mass: 20 kg Armature Diameter: 290 mm Armature Resonance: 2300 Hz Permissible Eccentric Moment: 850 N·m Frequency Range: 0-2600 Hz. Maximum Force: 24 kN (sine and random) 48 kN (shock) Maximum Acceleration: 1200 m/s² (sine) 840 m/s² (random) Bodpfx Agow H N U Djljcu 2400 m/s² (shock) Maximum Displacement: 100 mm p-p. Maximum Load Capacity: 400 kg. Ambient Conditions: Temperature 0-40 °C, Humidity 0-85 %RH. Maximum Output Power: 30 kVA (SA3AM-i40) + Shaker Armature 290 mm Usable up to 2000 Hz Weight: 410 kg (SA3AM-i40) Total weight approx. 2800 kg Condition: used Scope of delivery: (see picture) (Specifications subject to change and error!) For further questions, please contact us by phone.

Year of construction: 2020, condition: excellent (used), Weiss Type: C/800/55a/25/S Year of manufacture: 2020 Weiss ClimeEvent Climate Test Chamber, Water-cooled Chamber volume: 800 liters Internal dimensions: Height 950 mm, Width 1100 mm, Depth 800 mm External dimensions: Height 2015 mm, Width 1415 mm, Depth 3156 mm Floor load capacity: designed for a maximum load of 250 kg Specifications for temperature testing: Temperature range: -55 to +180°C Temporal temperature fluctuation at chamber center: ±0.1 to ±0.5 K Spatial temperature deviation (temperature gradient): 0.5 to 2.0 K Heating rate: 25 K/min Cooling rate: 25 K/min (down to -45°C) Heating compensation: max. 8000 W Specifications for climate testing: Temperature range: +10 to +95°C Humidity range: 10 to 98% RH Climate performance data (excerpt) Humidity range: 10 to 98% relative humidity (RH) Humidity deviation (temporal): At chamber center, in steady-state condition, depending on climatic setting: ±1 to ±3% RH Temperature deviation (temporal): At chamber center, in steady-state condition, depending on temperature: ±0.1 to ±0.3 K Temperature uniformity (spatial): Relative to the setpoint (in the range > 20% RH): ±0.5 to ±1 K Operational data: LED strip: 24 V, 6.8 W / 2 x Halogen lamp 24 V, 50 W Rated voltage: 3/N / PE AC 400 V ± 10%, 50 Hz Rated power: 53 kW Rated current: 87 A Refrigerant: WT69-R449A Chamber is equipped with Greenmode Bodpjw R Rt Iefx Agljcu Weight: approx. 2050 kg Buyer Safety Information! The following steps are performed on all chambers we offer: 1. Functional inspection and replacement of necessary components 2. Refill with legally compliant refrigerant if required 3. Leak test with certificate 4. Upon successful testing, chambers undergo a documented trial run. Condition: used Scope of delivery: (see picture) (Specifications and technical data are subject to change and error!) For further questions, we are happy to answer your call.

Condition: used, Espec Type: TSD-100 100 liters usable chamber volume for larger test specimens up to 30 kg. Bcedpfx Aoxugq Aeglsu Compliant with all common international standards. Water-cooled Temperature range hot chamber: +60°C to +200°C Temperature range cold chamber: -70°C to 0°C Test chamber interior dimensions: 710 x 345 x 410 mm (W x H x D) External dimensions: 1100 x 1885 x 1965 mm (W x H x D) Water-cooled refrigeration unit Programmable control via touch panel Automatic defrosting Overtemperature protection Operating hours counter Mobile design (on castors) 2 stainless steel specimen baskets Cable entry port ⌀ 100 mm Refrigerants: 3 kg R404A, 1 kg R23 Power supply: 400V 3Ph 50Hz Max. current consumption: 32A Condition: used Weight: 1100 kg Important safety information for buyers: The following procedures are performed on all chambers offered by us prior to sale: 1. Functional check and replacement of necessary components 2. If necessary, refilling with legally compliant refrigerant 3. Leak test with certificate 4. Upon passing inspection, chambers undergo a documented test run. Condition: used Scope of delivery: (see picture) (Subject to modifications and errors in technical data and specifications!) For further questions, please feel free to contact us by phone.

Condition: used, Keysight / Scienlab Battery Test System SL1001A + Angelantoni Climate Chamber DM500 C 10 ESS SPEEDY BT SP Complete Battery Testing System – For Laboratory Use Incl. PC, software & technical documentation For sale is a professional battery test system, consisting of: - Keysight / Scienlab SL1001A Battery Test System - Angelantoni DM500 C 10 ESS SPEEDY BT SP Climate Chamber - Monitoring/Sampling Unit - Control PC with original software - Technical documentation The system is fully functional, well-maintained, and ideally suited for battery module testing, research, development, and quality assurance. Technical Data – Scienlab SL1001A: - Manufacturer: Keysight / Scienlab - Model: SL1001A - Year of manufacture: 2020 - Voltage / Current / Power: 80 V / 600 A / 24 kW - Dimensions (L×W×H): approx. 1.6 × 0.9 × 3.3 m - Weight: approx. 700 kg - Function: Charging, discharging, and cycling of battery modules - Condition: Very well maintained, laboratory use only Technical Data – Angelantoni DM500 C 10 ESS SPEEDY BT SP: - Manufacturer: Angelantoni Industrie S.r.l., Italy - Model: DM500 C 10 ESS SPEEDY BT SP - Year of manufacture: 2019 - Weight: approx. 1,225 kg - Temperature range: -70 °C ... +180 °C - Humidity range: 10 ... 98 % rH - Refrigerants: R449A + R23 - Pressure ranges (PS Hi/Lo): 28 bar / 8 bar - Wi-Fi integrated - CE certification present - Internal dimensions (L×W×H): approx. 1.6 × 2.3 × 3.3 m - Function: Temperature and humidity testing, ESS (Environmental Stress Screening) - Power supply: 3PH + N + PE, 400 V ±10 %, 50 Hz, full load 54 A - Max. power consumption: 32.5 kW Monitoring / Sampling Unit: - Dimensions: 0.6 × 0.5 × 0.2 m - Measured variables: Cell voltages, current, temperature - Interfaces: CAN, Ethernet - Compatible with Scienlab / Keysight PathWave software PC + Software + Documentation: - Industrial PC with control and measurement software - Enables automated test runs, logging, and data analysis Overall Dimensions / Weight (approx.): Component Dimensions (L×W×H) Weight Scienlab SL1001A 1.6 × 0.9 × 3.3 m 700 kg Angelantoni Chamber 1.6 × 2.3 × 3.3 m 1,225 kg Monitoring / PC 0.6 × 0.5 × 0.2 m 50 kg Total system L 3.2 m × W 2.5 m × H 3.3 m approx. 1,975 kg Applications: - Development, testing, and lifespan analysis of battery modules (e.g., Li-ion, LFP, NMC) - Fast charging and cycle tests - Environmental simulation for temperature and humidity - Research, industrial, and university laboratories Important Note: Bcedsxuqk Hepfx Agleu "The table shown in the photos is not included in the sale." Scope of Delivery: - Scienlab SL1001A power unit - Angelantoni DM500 C 10 ESS SPEEDY BT SP climate chamber - Monitoring/Sampling unit - Control PC with software - Technical documentation and manuals - Connection cables and accessories (as available) Condition: used Scope of delivery: (see image) (Specifications and data are subject to change and error!) For any further questions, we are happy to assist you by phone.

Condition: used, Chroma Type: ATE 17020 The Chroma 17020 is a highly professional, modular test system for lithium-ion & other battery pack qualification. Particularly strong in: - Lifetime testing, BMS verification, and validation of complex charging cycles - High energy recovery – up to 85% efficiency - Flexible expansion through numerous channels or higher current ranges - Enterprise deployment with extensive safety features & data persistence Technical data – Chroma ATE 17020 PTS Feature Specification Model: Chroma ATE 17020 PTS System type: Regenerative battery pack test system (charge/discharge test) Channel output: 600 W to 60 kW (modular and scalable) Total output: Up to 600 kW (depending on configuration) Voltage range: 20 V / 60 V / 100 V / 200 V / 500 V Current per channel: Depending on module: from a few amps up to >300 A per channel Parallel operation: Yes, for higher current up to 2,600 A Current and voltage accuracy: ±(0.05% of reading + 0.05% of range) Power accuracy: ±0.1% Transition time (charge/discharge): < 50 ms Sampling rate (measured data): up to 50 kHz (with BatteryPro) Data logging: Cyclic, 10 μs – 1 s / memory for 60 min power failure Test modes: CC, CV, CP, CC-CV, DCIR, pulse, drive cycle, dynamic profiles Number of channels: Up to 60 channels (expandable) Communication: CAN, S-Bus, Ethernet, USB Software: Chroma BatteryPro (test programming, real-time monitoring) Protection functions: OVP, UVP, OCP, UCP, OTP, reverse polarity, wire loss, delta V/I, etc. Energy recovery: Yes – up to 85% energy efficiency, grid-friendly (THD < 5%) Cooling: Fan cooling, low waste heat due to energy recuperation Temperature monitoring: Optionally integrable, range 0–90°C ±2°C Dimensions & weight: Depending on configuration (e.g. 19″ rack, approx. 300 kg) Mains connection: 3-phase, 400 V AC (depending on model) Applications: E-mobility, battery development, quality assurance, cell research Weight: approx. 455 kg Condition: used Bsdpfx Agswwrxaelscu Scope of delivery: (See picture) (Specifications and technical data are subject to change and errors excepted!) If you have further questions, we are happy to assist you by phone.

Condition: excellent (used), Vötsch Type: VT 7060 Vötsch VT 7060 Temperature Chamber 600 Liter with Simcon 32-net Chamber is air-cooled Reliable climate chamber for demanding environmental simulations Ideal for laboratories, R&D, and quality assurance. Device description: For sale is a professional temperature chamber from manufacturer Vötsch Industrietechnik, model VT 7060 with SIMcon 32-net controller. This high-performance unit is suitable for a wide range of demanding environmental simulations, from material testing and electronics tests to long-term climate stress tests. Technical data (summary): Model: Vötsch VT 7060 Internal volume: approx. 600 liters Temperature range: –70 °C to +180 °C Temperature deviation when stabilized: Temporal: ±0.1 K to ±0.5 K Spatial: ±0.5 K to ±2.0 K Temperature change rate (without test specimen): Heating: 4 K/min Cooling: 3 K/min Control: SIMcon 32-net with touch panel Interfaces: RS232, optionally RS485/422 1 × port, NW 50 mm, left 1 × port, NW 125 mm, left 2 × ports, each NW 125 mm, right External dimensions (approx.): Width 1090 × Height 1960 × Depth 1995 mm Internal dimensions (approx.): Width 800 × Height 800 × Depth 950 mm Rated voltage: 3/N/PE AC, 400 V ±10 %, 50 Hz Rated power: 9.1 kW Rated current: 19.0 A Refrigerants: R 404A and R 23 Weight approx. 675 kg For your safety as a buyer, please note the following: Bodpswybb Njfx Agljcu The following steps are carried out on all chambers we offer: 1. Functional test and replacement of necessary components 2. If necessary, new charge with legally compliant refrigerant 3. Leak test with certificate 4. After successful testing, the chambers undergo a documented test run. Shipping / Collection: Collection preferred Shipping via freight carrier on pallet possible Europe-wide. (Shipping costs according to expenditure) Condition: used Scope of delivery: (see picture) (Specifications and technical data subject to change and errors!) For further questions, we are happy to assist you by phone.

Condition: good (used), Heraeus Vötsch Type: VTS 7034-5 Heraeus Vötsch temperature test chamber water-cooled Temperature range -70°C to + 180°C Temperature deviation temporal ± 0.1 to ± 0.5 K Temperature deviation in terms of time ± 0.5 to ± 2.0 K Temperature change rate cooling 5.0 K/min Temperature change rate heating 6.5 K/min Heat compensation +20°C 3000 W Thermal compensation -20°C 3000 W Test chamber dimensions: Width 580 mm Depth 765 mm Height 750 mm External dimensions: Width 870 mm Depth 1595 mm Height 1775 mm Bcsdpeun Rv Nofx Agleu Test chamber volume 335 liters Rated voltage: 3/N/PE AC, 400V ±10 %, 50Hz Rated power: 10 kW Rated current: 21 A Sound level at 1m distance (free-field measurement) < 69dB (A) Lateral feed-through 5.5 cm / 12.5 cm Cabinet is water-cooled Refrigerant: R- 404A and R 23 Weight approx. 570 kg The following information for you as a buyer! The following points are carried out on our offered chambers in advance: 1. functional check and replacement of necessary components 2. refilling with legally compliant refrigerant 3. after successful inspection, the chambers are subjected to a test run, which is monitored with calibrated devices. Condition: used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: excellent (used), CTS Temperature test chamber T-55/1000 Li water-cooled Temperature range: -50°C to +100°C Rated voltage: 400V 3/N 50Hz Rated power: 9.5 kW Nominal current: 18 A Compressor: TFH2511Z / TFH2511Z Refrigerant R404A/R23 The type designation of the CTS cabinet series is composed as follows: z. e.g. type T -55/1000/Li 1) T means: temperature 2) -55 means: lower temperature -55 °C 3) 1000 means: 1000 liter test chamber volume 4) Li means: special equipment for tests with lithium-ion accumulators Control: 32 bit controller LCD control panel Digital display of set and actual values Numerical input of setpoints Error messages in plain text Ethernet interface RS 232 interface Free switching channels for on-site test material control Test room lighting: energy-efficient, high-intensity LED light strip mounted on the door Insert grid: Stainless steel, support surface 970 x 980 mm Load per shelf max. 35 kg Total load with max. grating load 100 kg 1a Feed-through NW50 1b Feed-through 2x NW125 1c Entry port 2x Rp 314° for Minimax Technical performance data: Temperature tests: Temperature range -50°C to +100°C Temperature deviation ≤ ±0.3 K in time Temperature change rate according to IEC 60068-3-5 Heating 2.5 K/min Cooling 2.5 K/min Heat compensation approx. 4000 W at +20°C approx. 2200 W at -40°C The technical data refer to an ambient temperature of +25 °C, rated voltage 400V, without test material, without heat compensation and without additional equipment. Options may affect the performance data. Dimensions: Test volume 1000 liters Test chamber dimensions Height, approx. 1000 mm, width, approx. 860 mm, depth, approx. 1100 mm External dimensions Height, approx. 1950 mm, width, approx. 1270 mm, depth, approx. 1900 mm Bsdovba Raopfx Aglocu Operating data: Electrical connection 400 V +6/-10 %, 3/N, 50 Hz Nominal current 18 A Rated power 9.5 kW Protection class IP 54 Sound pressure level < 58 dB(A) (according to DIN EN ISO 3744 measured at a distance of 1 m from the front) Mass approx. 1000 kg Heat output to the installation room 10.4 kW Cooling unit: water-cooled, low-noise, fully hermetic Infinitely variable output adjustment via electronic monitoring and control system, environmentally friendly refrigerant R404A/R23 The following information is for your safety as a buyer! The following points are carried out on our offered chambers in advance: 1. functional check and replacement of necessary components 2. if necessary, refilling with legally compliant refrigerant 3. leak test with certificate 4. after successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: used, Vötsch Type: VCS 7034-5 Water-cooled climatic test chamber Test chamber capacity 335 liters Performance for temperature tests Temperature range -70 to +180°C Temperature deviation in time K ±0.1 to ±0.5 Spatial temperature deviation K ±0.5 to ±2.0 Temperature gradient 1 to 4 Rate of change : Cooling 6.7 K/min Heating 6.8 K/min Heat compensation at +20 °C 3000 W / at -20°C 3000 W Temperature calibration values +23 °C and +80 °C Performance for climate tests Temperature range +10 to +95°C Temperature deviation in time ±0.1 to ±0.3 K Spatial temperature deviation ±0.5 to ±1.0 K Temperature gradient 1 to 2 K Humidity range 10 to 98% Humidity deviation in time ±1 to ±3% Dew point range -3 to +94°C Heat compensation 400W Climate calibration values +23 °C / 50 % r.h. and +95 °C / 50 % r.h. Test chamber dimensions: Width 580mm Depth 765mm Height 750mm External dimensions: Width 870mm Depth 1595mm Height 1775mm Electrical connection: 3/N/PE AC, 400 V ±10% 50 Hz Rated power: 10kW Rated current: 21 A Sound pressure level: 64dB(A) Cooling water consumption: 1.4m³/h Refrigerant: R-404A / R-23 The following information is for your safety as a buyer! The following points are carried out on our offered chambers in advance: 1. functional check and replacement of necessary components 2. if necessary, new filling with legally compliant refrigerant 3. leak test with certificate 4. after successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (see picture) Bcedsuxq T Djpfx Aglsu (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: excellent (used), Weiss temperature test chamber Here we offer a temperature test chamber. Weiss temperature test chamber water cooled Technical data: Test cabinet designation: WT-600/70 Outer dimensions with hinges and door lock height 1995 mm, width 1090 mm, depth 1660 mm Outer dimensions without hinges and door lock height 1995 mm, width 1000 mm, depth 1660 mm Internal dimensions: Height 950 mm, width 800 mm, depth 800 mm Test chamber capacity: approx. 600 liters cold / heat operation -70°C to 180°C Temperature change per time cooling approx. 2.5 K/min Heating up approx. 4 K/min 3/N/PE AC 400V ±10% 50Hz Rated power: 9.1 kW Rated current: 19 A Fuse on site: 32 A slow blow Bjdpeiqk Abjfx Aglecu Permissible test material weight Total load of grate supports 80kg test chamber floor 80kg, insert grate 40kg Refrigerant: R 404A/R23 Weight: 675kg Type: WT-600/70 For you as a buyer for safety the following information! The following points are carried out on our offered chambers in advance: 1. functional check and exchange of necessary components 2. new filling with legally compliant refrigerant 3. after successful inspection, the chambers are subjected to a test run, which is monitored with calibrated equipment. Condition: used / used Scope of delivery: (See picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: excellent (used), Here we offer a TIRA temperature test chamber. TIRA temperature test chamber air-cooled The chamber has the option for an external test box with external sensor connection can therefore also be used as an external temperature control unit. Temperature range -20°C...+140°C Temperature stability over time ± 0.1°C...± 0.3°C External dimensions Width 860 mm x depth 1500 mm x height 2100 mm Test chamber dimensions width 601 mm x depth 545 mm x height 692 mm Bcedpfx Agsnyh T Sjleu Electrical connection 400V +6% / -10% 50Hz 3P+N+PE Rated current: 10.0 (max.17) A Rated power: 5.2 (max.9.0) kW Net weight: 735 kg Refrigerant: R404A / R23 Type: TTRE 2001S The following information is for your safety as a buyer! The following points are carried out on our offered chambers in advance: 1. functional check and replacement of necessary components 2. if necessary, new filling with legally compliant refrigerant 3. leak test with certificate 4. after successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: excellent (used), Espec Here we offer an Espec(ThermoTec) stress test chamber. Overpressure humidity tests at over 100 degrees in many different modes Program capacity of 10 patterns with 30 steps per pattern A variety of protection mechanisms; overheat/overpressure protection, detection of water- supply failure.Complete door interlock and temperature sensor. Saturated Temp Range 105 to 142.9°C Unsaturated Temp Range 105 to 132.9°C Humidity range 50 to 100% r.h. Nominal pressure 0.196 MPa at 132.9°C and 100% e.F. External dimensions: width 740 x height 1553 x depth 1000 mm Test chamber dimensions: Width 355x Height 355 x Depth 426 mm Other equipment: with rails and grid Test material connections in the interior Type: EHS-221M Scope of delivery: See pictures 300 kg Condition: Used Scope of delivery: (See picture) (Changes and errors in the technical data, specifications are reserved!) Bcedpfsn Arznsx Agleu Further questions we can answer on the phone for you.

Condition: excellent (used), Vötsch shock test chamber Here we offer you a Vötsch shock test chamber. Water cooled Temp. range -80C to +220C Hot chamber +50 to +220 Medium chamber -10 to +90 Cold chamber -80 to +70 Mains voltage 400V +-10% 3/N 50Hz Rated current 30.5 A Rated power 13.5 KW Refrigerant VK : R 404A 3.00kg p*: 25bar Refrigerant TK : R23 15bar p* : 25 bar Condition: used / used Type: VT 7012 S3 For you as a buyer for safety the following information! The following points are carried out on our offered chambers in advance: 1. functional check and exchange of necessary components 2. new filling with legally compliant refrigerant 3. after successful inspection, the chambers are subjected to a test run, which is monitored with calibrated equipment. Condition: used / used Scope of delivery: (See picture) (Changes and errors in the technical data, specifications are reserved!) Bcedpfx Agon Avcujleu Further questions we can answer on the phone for you.

Condition: excellent (used), Feutron Type: 3702/06 Water-cooled climatic test chamber Technical data: Test chamber nominal volume 2.0 m³ Dimensions: Test chamber exterior, with humidifier console Width 2970 mm Height 2370 mm Depth 1530 mm Rear wall Minimum insertion dimensions: Width 2970 mm Height 2390 mm Depth 1550 mm Test chamber: Width 2000 mm Height 1000 mm Depth 1000 mm Double-leaf door, clear width Width 2000 mm Height 1000 mm Heated viewing window, 2 pieces Width 500 mm Height 600 mm Feed-through opening, 1 side panel left ∅ 75 mm Temperature range: -40...100°C Climatic range: 10...95°C Temperature difference, temporal ≤ ± 0.5...± 1.0 ΔN/K Change rates measured in the supply air without load Cooling up to 2.0 on average K/min Heating up to 2.0 on average K/min Humidity range: 10...95 %r. F. Humidity difference, temporal ≤ ± 3.0 %r. F. Dew point range, temporary down to -5... 95°C Bcjdsk E Hnqjpfx Agleu Refrigeration system: water-cooled semi-hermetic Bitzer system Refrigerant: R507 (Μ-Κ1) Air conditioning and dryer refrigeration system air-cooled /hermetic system Refrigerant: R134a (Μ.ΚΚ) Power supply: Electrical mains connection: 400V 3/N/PE.AC,50Hz Mains plug: CEE 5-роlig, 32 A, with 5.0 m cable Max. simultaneous power requirement 10.0 kW Supply line fuse: 3x 25, Char, C A Degree of protection IP20 Weight: 1300 kg Condition: used Scope of delivery: (see picture) (Subject to changes and errors in the technical data and specifications) We will be happy to answer any further questions you may have on the phone.

Condition: excellent (used), Lindner Bursting Test Stand Here we offer a Lindner burst test stand. AGB Bursting Test Stand TMM4 Technical data: AGB Bursting Test Stand TMM4 Year of manufacture 2015 Rated voltage: 3/N/PE AC 400V Rated power: 5,5 kW Temperature range chamber: RT ... 180°C Temperature range medium: RT ... 135°C Pressure range: 0 ... 5 bar Compressed air supply: 6-8 bar Test medium: glycol / water Heat transfer oil Fragoltherm Q-HTF Dimensions: length 2150 mm x width 1050 mm x 2160 mm Operating voltage: 3/N/PE AC 400V +/-10% 50Hz power: 5,5kW rated current: 8A Back-up fuse: 16A Control voltage: 24VDC PLC system: S7-1215 DC/DC/RLY For the commissioning of the burst test bench the following items are necessary: Pump, cooling tower & fire alarm panel these are not supplied. Bcodpfxjlx A T Do Agleu Type: AGB burst test rig TMM4 weight approx. 705 kg Condition: used / used Scope of supply: (See picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: excellent (used), Here we offer a temperature shock test cabinet. Bcodpfx Aelgux Aeglou White Temperature Shock Test Cabinet Air Cooled Specification: Temperature range hot chamber +60°C ... +220°C Temperature range cold chamber -10°C ... -80°C Change hot/cold chamber 10 s Temperature constancy ±1 K Dimensions and other data: External dimensions: Height 1990 mm Width ( without and with door hinge ) without....approx. 1820 mm with....approx. 1850 mm Depth ( without and with test room door ) without....ca. 900 mm with....ca. 1155 mm Dimensions of the lifting basket ( test chamber ) height 450 mm, width 500 mm, depth 600 mm volume 130 liters Test space load max. 20 kg Test chamber floor load max. 20 kg Cooling water pressure min. 2 ... max. 6 bar Max. Backup fuse 35 A (plug 32 A CEE) Sound pressure level, 1 m in front of unit approx. 65 dB(A) Cooling cascade water cooled Connected load: 3/N/PE/AC 400V ±10% 50Hz /14,0 kW nominal current 26,0 A Refrigerant R 404A / R23 Weight: approx. 950 kg Type: TS 130 Condition: used / used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.