Used Veneer Clipper for sale (578)

Condition: used, Year of construction: 2008, Technical data: - Manufacturer: Bütfering - Type: Optimat SGO 211/RC - Number of grinding units: 2 - Year of manufacture: 2008 - Working width: 1.100 mm - Grinding belt width: 1.120 mm Fsdpoyh Hwuofx Al Ujpn - Grinding belt length: 1.900 mm - Workpiece thickness: 3-160 mm - Feed speed: 2,5-13 m/min. - Table height adjustment Standard equipment: - Automatic workpiece thickness adjustment - Stepless feed speed via requency converter. - 125 grinding programs can be stored - Wear-free braking system 1. Grinding unit (R) - Calibration roller - Profiled steel contact roller - Diameter 160 mm - Drive motor: 15 kW 2nd grinding unit (C) - Combination unit with roller and grinding shoe - Rubberized contact roller 65 Shore - Contact roller diameter 160 mm - Electronic link pressure bar with segment width 35 mm. - Belt speed: 12 and 21 m/s - Tolerance compensation up to 1 mm - Suitable for veneered surfaces and solid wood. - Drive motor: 11 kW - Total connected load: approx. 28 kW - Operating voltage: 400 V / 50 Hz. - Compressed air consumption at 6 bar, 20 L/min. - Belt blow-off device per pressure surge 440 L/min. - Extraction volume: approx. 2,880 m3/h/ at 20 m/s - Extraction connection: Dedusting: 1 x Ø 160 mm (grinding unit, roller) 1 x Ø 160 mm (grinding unit, shoe) Dimensions: - Length: 1,700 mm - Width: 1,850 mm - Height: 2,100 mm - Location: not in stock

Condition: new, Year of construction: 2024, Single-shaft shredder HOKUTech special offer model H600 Compact, robust, high throughput The H600 high-performance shredder with its flexible application options can process all types of wood-based materials (hardwood, softwood, chipboard, MDF materials, plywood, veneer residues, etc.) into chips and achieves an enormous reduction in the volume of bulky materials. The hydraulically controlled pusher feeds the wood waste to be shredded into the cutting area of the rotor and is controlled automatically and load-dependent. The high-performance solid steel electric rotor has a diameter of 252 mm and operates at a rotor speed of 85-95 rpm. The concave-ground, aggressive and 4-way rotating knives / reversible cutting crowns are located in milled knife pockets on special knife carriers. This highly efficient system guarantees high throughput, low energy consumption and optimum discharge of the shredded material by reducing the cutting gap between the counter blade and the rotor. Chip size (10 - 60 mm) Technical data: - Hopper opening - Hopper capacity - Working width of the rotor - Diameter of the rotor - Drive power - Rotor speed 600 x 800 mm 0.6 m3 600 mm 252 mm 15 kW 90 rpm Fodpfx Ajutmw Hel Uopn Location: Comes to stock 54634 Bitburg - available by arrangement -

Year of construction: 2026, condition: as good as new (ex-display), Vacuum membrane press The VP series is the optimal solution for woodworking. The VP 3000 is equipped with heating technology, which reduces the drying time of the adhesive, thereby increasing performance. Possible applications: Veneering / Form gluing / Covering... Coating of various profiles (veneer, paper, plastic...) Wood bending: Production of curved and laminated components The heating system is equipped with temperature control Rubber membrane 2.5 mm Fpedpfx Aledvltyj Uen Tabletop is made of plastic 12 mm Oil-free Becker vacuum pump 25 m3/h The control system of the vacuum / tank capacity 15 l Working area: 3000x1500mm Heating system temperature: Max. 60 degrees C Heating system: 4.5 kW Pump power: 0.75 kW Vacuum pump flow rate: 25 m3/h Rubber membrane External dimensions: 3100 x 1650 x 1600 mm Weight: 450 kg Location: Available from stock in 54634 Bitburg - free loading -

Condition: new, Year of construction: 2024, Hard cover making table -Casemaker- The device is brand new, with a 12 month warranty. European production, based on branded subassemblies. Duty Cycle: The operator manually handles the covering material, to the gluing device in which the hot glue is automatically applied (operating temperature 60-70 ° C). A sheet of covering material with glue the operator places it manually on the suction table, then manually handles sheets of cardboard and spine. The pre-prepared cover is inserted into device manually, which winds up and glues the top and bottom of the covering material (patented brush system). During the sizing operation, the cover is pressed through the guide rolls. Covers leaving the unit are immediately ready for further processing The machine is equipped with: – gluing device for applying glue onto the top of the sheet – table with a suction – guides fixing the veneer and cardboard – wrapper module – delivery table Fpjdpfx Alszyz Erj Uon Technical data: Max format: 840x500mm Min format: 100x100mm Performance: 100-150 covers / h Thickness of the covering material: 80-200 gsm Thickness of cardboard: 1-4mm Overlap covering material: 13-20mm Glue temperature: 30-100 ‚C Glue capacity: 2-3kg Smooth adjustment of the rotation speed of the rollers and brushes Types of covering material: fabric, laminated paper, photographic paper, imitation leather, PVC, polyurethane. Dimensions of the machine: 1500x1000x1000mm Power supply: 380V Consumption: 3.7kW Machine weight: 500kg

Condition: used, machine/vehicle number: 006458, Type of edging: Thin edge, Thick edge, Veneer Gluing System: EVA Hotmelt Premilling Unit: yes Fpodponzrt Aefx Al Usn Corner Rounding Unit: yes Max feed speed: 11 m/min Maximum panel thickness: 50 mm

Condition: new, CNC Panel Saw Wehrmann WT-38/1040 New machine For the conventional cutting of workpieces made of wood/wood-based materials with laminate (CLP, HLP), paper, foil or veneer Panel dimensions + data (finished panel): Length: from 140 mm Width: min. (finished dimension) 38+38 mm Width: max. (finished dimension) 520+520 mm (asymmetrical cutting is possible) Thickness: 8 mm - 40 mm Weight: approx. max. 30 kg Workpiece shape: rectangular Basic structure: - User-friendly combination machine with adjustable zero line - All drives and adjustments are servo-controlled - The machining motors are frequency-controlled. - Stable steel welded construction - Workpiece transport is carried out by means of a transport belt and height-adjustable top pressure. Fsdszvdw Njpfx Al Uopn Base machine: - Sound-absorbing/protective hood with safety interlock - The required connection nozzles for an external extraction system with an air velocity of min. 28 m/sec. (underpressure 2480PA) - A compressed air connection incl. maintenance unit. - Integrated control cabinet with cooling unit for operating the machine at an ambient temperature of 10 - 45 degrees Celsius - PC control Beckhoff - Safety and protection devices according to CE guidelines - CE marking Feed rate v= 5 - 40 m/min servo-controlled drive Electronic height adjustment of 5 - 45mm adjustable via Beckhoff servo axis Stop ruler made of Teflon on the right side of the machine adjustable via Beckhoff servo axis Infeed ruler on the left with pneumatically sprung unit adjustable via Beckhoff servo axes Machine equipment: Unit 1: Slitting saw, frequency-controlled Milling stand with column guide and connecting plate Motor Perske 4.4 KW 50 Hz 400 Volt 4500 RPM. Tool holder D = 35 keyway External + internal thread right / left, controllable via servo drive, operating in the same direction, not swiveling with height adjustment via Beckhoff servo axis Lateral adjustment with mechanical digital display Saw blade max. 350 mm without tools Flow-optimized extraction hoods Unit 2: Saw motor, frequency-controlled Milling stand with column guide and connecting plate Saw motor not controllable, operating in the opposite direction Motor Perske 6 KW 50 Hz 400 Volt 5000 RPM. Tool holder D = 35 wedge shaft with external + internal thread right / left Saw blade max. D400 mm without tools with manually adjustable splitting wedge with height adjustment via Beckhoff servo axis Lateral adjustment with mechanical digital display Flow-optimized extraction hoods Beckhoff control technology - PC-based control system with integrated PLC and electronic path control - Virtually unlimited program memory - Operation via keyboard / mouse / touch - Reporting system for operator and error messages - MDE Basic for recording machine data, production time, set-up time, downtime, fault time, quantity and adjustable recording period - Fast data exchange between control and I/O component via EtherCat - Uninterruptible power supply for panel PC - Feed lock for adjacent machines or transport - Powerful panel PC with integrated 15.6 inch display with touch screen, integrated keypad, keyboard and mouse - USB port - Fast EtherCat interface (field bus) - Ethernet network connection RJ45 - Operating system Windows with TwinCat 3 system for real-time control

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Very well-maintained and robust OTT heating plate press, type ST 2511/80, with a pressing force of 80 tons. The press is ideally suited for gluing and veneering panels, furniture components, and other wood-based materials. The machine is in very good used condition. Technical data: Manufacturer: Paul OTT Type: ST 2511/80 Year of manufacture: 1987 Machine no.: A 6815 Pressing area: approx. 2,500 × 1,100 mm Pressing force: 80 t Specific pressing pressure: approx. 2.9 kg/cm² Total power: 15.6 kW Rated voltage: 380 V Frequency: 50 Hz Control voltage: 220 V Rated current: 24 A Heated press plates Temperature display for upper and lower heating plates Pressure and pressing time setting Safety tripwires Condition: very good Equipment: Upper and lower heating plates Hydraulic pressing device Adjustable pressing pressure Adjustable pressing time Temperature monitoring Safety tripwires Transport possible for an extra charge! The machine is currently still at the customer's site but would be immediately available! The machine will be inspected before sale. For used machines with a year of manufacture of 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sales and changes are subject to change. All information without guarantee. Fjdpezxzbdsfx Al Uepn

Condition: new, Year of construction: 2025, Exhibition machine Year of manufacture: 2025 Equipment and technical data: MODEL Excel 2NRKRT 2-BELT MACHINE 1st BELT: CYLINDER 2nd BELT: COMBINATION UNIT CYLINDER/SHOE FOR SOLID WOOD, VENEER, AND INTERMEDIATE GRINDING FOR LACQUERING - Usable WORKING WIDTH mm 1350 - BELT LENGTH mm 1370 X 2150 - MAX. WORKPIECE THICKNESS mm 160 Fedjzh Rufopfx Al Uepn - STEEL CALIBRATION CYLINDER mm 180 - Rubber-coated GRINDING CYLINDER mm 180 - GRINDING SHOE WIDTH mm 50 - BELT MOTOR POWER KW 14.7 - BELT SPEED m/s 18/16 - FEED MOTOR POWER HP 0.75 - Adjustable gearbox with steplessly adjustable feed speed m/min 4/20 - HEIGHT ADJUSTMENT MOTOR HP 0.33 - Mechanical BELT OSCILLATION "ECO GEAR PATENT SYSTEM" - 1 PCS. DRUM BRAKE for belt braking - Swiveling ROLLER for belt tension - 3 PCS. PRESSURE ROLLERS; with rubber coating - EMERGENCY STOP SWITCH in the infeed area Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2005, - Automatic infeed table - KFA unit - Return system Used single-sided edge banding machine Manufacturer: IMA Type: Combima Systems / I/R751220/R3 1 single-sided combination machine for trimming, edge gluing and edge finishing of panel-shaped workpieces made of wood and/or wood-based materials. Fjdpfezuyplsx Al Uepn - Automatic infeed table - KFA unit - Return system Technical data "Workpiece": Workpiece length - min.: 238 mm - max.: 2350 mm Workpiece width - min.: 142 mm - max.: 800 mm Workpiece thickness: - min.: 8 - 40 mm Technical data "Strip" (only for longitudinal processing): Roll material: - Paper edge bands & plastic edge bands: 0.3 - 3.0 mm - Veneer edge bands: 0.5 - 3.0 mm Edge height: - min.: 14 mm - max.: 45 mm Technical data "Machine": Variable workpiece overhang from the chain conveyor (including edge with edge thickness 0.3-3 mm): - min.: 40 mm - max.: 80 mm - PC control ICOS open - Feed speed v=5-25 m/min, frequency-controlled drive - Inclined roller table as infeed section NC infeed system for front and carcass parts - for length and width-independent automatic workpiece feed in single-sided edge processing machines. Only for the production of strip material in the 2nd pass - An additional stop rail, adjustable via NC axis. Double milling unit 08.376: - Controllable - Motor 1 operating in the same direction and motor 2 operating in the opposite direction - Reserve space on the unit carrier for a double trimming unit with electrical pre-installation for 2 x 6.6 kW. - Heater 300 lg, 2x1.5 kW, for preheating the workpiece edge. - Gluing unit 04.1570 system for straight edges and adhesive application to the workpiece. The edge thickness depends on the magazine used and is max. 3 mm. - Adhesive application for workpiece thickness max. 50 mm - 2 pre-melting tanks for PU adhesive - 12-position edge magazine for roll material 0.3-3 mm thick. (8 slots up to 3 mm, 4 slots up to 1.3 mm) Vertical roll holder for 12 rolls: - max. roll diameter 850 mm - max. edge height 45 mm - Trimming unit 08.42, for 2 motors mounted on the upper pressure bar - Pre-milling and milling unit with height sensor - with 1 motor 1000 W - Multi-profile / chamfer unit, with 2 motors 1000 W - Contour milling unit KFA 30 - Multi-profile drawing blade unit - Flat drawing blade 08.517 - Copy edging unit 08.604 - Edging unit 08.617-2 - Double milling stand 75.184, 1050 mm high, both stand sides can be used - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 6000 rpm - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 600 rpm - Motor spindle for the use of the Hydro-Format tool system - Return system, manufacturer Meinert Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm Single-sided edge banding machine Manufacturer: IMA Type: Novimat Contour/I/G80/790/L20 Year of manufacture: 2009 Technical data - Electronically controlled feed speed: 6-30 m/min - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm - Maximum edge overhang from above: up to 8 mm edge thickness - 5 mm, over 8 mm - 2 mm Fodpfszuyprox Al Uepn Workpiece size: - Minimum workpiece length in the feed direction: 150 mm - Minimum workpiece width: 25 mm, thickness: 65 mm - Minimum workpiece thickness: 8 mm (without profile trimming blades) or 12 mm with profile trimming blades - Maximum workpiece thickness: without corner copying, max. 60 mm (max. 40 mm with corner copying) - Smallest element: 150 mm x 150 mm or 65 mm x 300 mm Note: *65 mm with a maximum piece thickness of 25 mm The edge banding machine is equipped with: - Hand-adjustable guide rail for inserting workpieces - Trimming units 08.376, 2 motors, each with 4.5 kW, spindle speed 9000 rpm, 150 Hz - Heating unit for warming the workpieces - Gluing unit with drive 283.1513, featuring a tightly sealed oil pan, drive arranged with glue pot content of 0.8 l and glue application height of 60 mm, with a pneumatic quick-clamping system for hot melt and PU adhesives, magazine for edge banding rollers and strips, edge banding roller diameter 800 mm - Glue pellet preheating unit with automatic feeding of glue pellets from a 30 kg container. - Automatic preheating unit for PU cartridges with a weight of approx. 2.5 kg and a capacity of 8-10 kg/h - Trimming unit 08.42/30/B, pneumatic adjustment of the saw blades from 0 - 25°, 2 motors 660 W, 200 Hz with frequency inverter and braking function - Pre-milling unit 08.055, swiveling up to max. 30° - Multi-chamfering unit 08.342, 2 motors, 660 W, 400 V, 200 Hz, 12000 1/min - Cleaning agent dispenser - Profile trimming blades 08.519 - Surface trimming blade 08.521 for removing excess glue from glue joints - Buffing unit 08.617-2, 2 motors with 180 kW, 50 Hz, 1400 rpm - Groove/milling unit with one motor Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Fsdpfx Aezuzw Djl Uepn Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Complete line Sign press Fsdpfx Alsz Dfyfs Ujpn oil Power 31 kW 250/130 cm Press entry and exit automation Ejector to die-head? Actually 'moulurière' refers to 'molder' or 'moulding machine'. 'Ejecteur vers moulurière par exemple' -> 'Ejector towards a moulding machine, for example' Glue applicator ORMA SC2R-300 at press entry 380 V Available immediately

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, type of input current: three-phase, input voltage: 400 V, grinding belt length: 3,000 mm, grinding belt width: 150 mm, table height adjustment: 180 mm, input frequency: 50 Hz, Langzauner LZK 3/4 oscillating edge sanding machine, with veneer edge sanding attachment and feed console Sanding unit adjustable from 0-45° Oscillation Miter stop Height-adjustable sanding table (180 mm) for utilizing the full width of the sanding belt Table size (front) 1000 x 350 mm Table size (side) 400 x 250 mm Connection power 4.6 kW Fedsz D Autopfx Al Uepn Belt length 3000 mm Belt width 150 mm Belt speed 22 m/s Weight approx. 350 kg Space requirement 1770 x 730 mm Year of manufacture 1997 Condition: Functionality tested

Condition: ready for operation (used), functionality: fully functional, FM 10-3100 A, horizontal veneer and panel saw, ideal for precise longitudinal cuts on veneer packs, chipboard, MDF, and thin solid wood, automatic feed and return of the saw carriage, infinitely variable control of feed rate, saw blade height, and cutting lengths, pneumatic special pressure beam, front and rear support tables HP 520, Fsdpfeyzxkwex Al Uepn longitudinal and cross cuts in a single operation, three-phase brake motor 6.8 HP / 5 kW and scorer unit, efficient dust extraction, maximum cutting height 60 mm, cutting length 3100 mm, good condition, machine ready for immediate use for further technical details, see pdf file (brochure) located in Neustadt/Weinstr. Transport available at additional cost! Due to the age of the used machine, warranty is excluded for commercial buyers.

Condition: used, Year of construction: 1989, Used Machine Features and Technical Specifications: - Small machine for processing molded parts - Processes hot-melt adhesive-coated edging material, which is reactivated using hot air - The workpiece is automatically fed by pressing it against the central, driven pressure roller, ensuring uniform adhesive reactivation and, consequently, reliable bonding - Thermostatic temperature control via a dial thermostat - Maintenance-free three-phase hot-air blower for continuous operation - Automatic airflow deflection - Pneumatically operated roller cutting device trims even the toughest veneer and PVC edges - Foot switch for processing molded parts - Workpiece thickness: 10–50 mm - Heating power: 3 kW - Connected load: 3.3 kW - Workpiece width (min.): approx. 25 mm - Edge thickness approx. 0.5–1 mm - Minimum inner radius approx. 25 mm - Feed rate 4 m/min. - Pneumatic pressure: 6 bar Fsdpfx Alszk N Ehs Uspn Weight: approx. 105 kg Availability: available shortly Location: Röllbach

Condition: new, 0 600 x 800 mm Motor output 15 kW 0 0,6 m³ Diameter of the motor 260 mm Dimensions (L/W/H) 1.805 x 1.118 x 1.646 mm Fpodpfx Ajx Iwfmjl Ujn Weight ca. 1.100 kg Hoku single-shaft shredder H 600 Compact, robust, high throughput ----- Technical manufacturer description: The H600 high-performance shredder with its flexible application options can shred all types of wood-based materials (hardwood, softwood, chipboard, MDF materials, plywood, veneer scraps, etc.) and achieves a high and, in the case of bulky materials, achieves an enormous reduction in the volume reduction of the material. The hydraulically controlled pusher feeds the wood waste to be shredded to the cutting area of the rotor and is controlled automatically and automatically and load-dependent. The high-performance electric rotor made of has a diameter of 252 mm and operates with a rotor speed of rotor speed of 85-95 rpm. The concave-ground, aggressive and 4-fold rotating knives / reversible cutting crowns are located in milled knife pockets knife pockets on special knife carriers. This highly efficient system guarantees, through the reduction of the cutting gap between the counter knife and rotor, it guarantees high throughput, low energy consumption and optimum optimised discharge of the shredded material. Clamp size (10–60 mm) depending on sieve perforation. Technical data: Hopper opening 600 x 800 mm Hopper capacity 0.6 m³ Working width of the rotor 600 mm Rotor diameter 260 mm Drive power 15 kW Rotor speed 90 rpm Number of knives: 14 pieces + 2 pieces Type and size of knives: concave/40 x 40 mm, reversible cutting crowns concave/ 30 x 30 mm, broaching knives Screen perforation: 10-60 mm connected load: 400 V +/- 5% / 50 Hz included: Switch cabinet (Rittal) with 5 m cable Electrical control (SPS Siemens) Star-delta start-up Rubber oscillating elements E-rotor with blade pockets milled into the profile Gear limit switch 1st row of knives Hold-down device on the pusher for long and large parts Large 40 x 40 mm blades for optimum material feed Very robust gearbox Special broaching blade to prevent lateral jamming ----- Price of the above mentioned machine on request! ----- Prices plus packaging and shipping, plus VAT. (technical data according to manufacturer - without guarantee !)

Year of construction: 2026, condition: new, The VPR-3500 vacuum membrane press is a universal press for woodworking and thermoforming. The VPR-3500 press is also swivelable and mobile. Fpedpjd Ecc Tofx Al Uen Possible applications: Veneering / Form bonding / Encasing… Coating of various profiles (veneer, paper, plastic…). Wood bending: Production of curved and laminated components. Vacuum system: Work surface with vacuum channels for uniform negative pressure, even with large workpieces. Becker vacuum pump / Oil-free / Tank capacity 100 l Work area: 3500x1500mm Pump power: 0.75 kW Vacuum pump flow rate: 40 m3/h Rubber membrane External dimensions: 3600 x 1650 x 1000 mm Weight: 400 kg Location: Available ex warehouse, 54634 Bitburg - Free loading -

Condition: new, Year of construction: 2026, functionality: fully functional, overall weight: 680 kg, total length: 320 mm, cutting length (max.): 300 mm, Alligator shears JMC 320 Fully overhauled, as new IMMEDIATELY available from stock IUT Beyeler AG, DE-06188 Landsberg. Financing and rental possible. We are looking for used alligator clippers! 12-month warranty The well established 320 Shear is a must for any yard and is now recognised as the industry standard for all shears of this type. One of our most popular shears, the McIntyre 320 Shear has maintained dominance in a demanding market due to its strength, quality and reliability The 320 is powerful enough to deal with a wide range of cutting and cleaning operations and is able to handle; automotive scrap, whole gear boxes, cylinder heads and blocks, oversized gate valves and of course all the usual non ferrous metal separations. The 320 can also be used to cut ferrous metals. Fpjdpfx Alsfxvklj Usn Every shear comes with 1 year guarantee, spare parts can be delivered within 24 hours to whole europe.

Condition: used, Heavy-duty hydraulic strip or beam press, Wemhöner Type VS 4 S, for veneering strips, gluing timber or other pressing tasks. The press has four independently controllable pressing surfaces. Includes dismantling and loading. Fixed loading date: 15 June 2026. Fjdpozryzcofx Al Uepn Glue applicator also available. Technical data: - Working length: 3,090 mm - Pressure: max. 104 t

Condition: excellent (used), Year of construction: 1993, Enorm edge sanding machine (now Kündig) In very good condition. Type: LBK 160 Fpedpfx Aszbyt Eel Uon Year of manufacture: 1993 With veneer edge sanding attachment Oscillation can be switched on. Electric height adjustment of the sanding unit Table can be tilted up to 45 degrees Sanding belt width 150 mm Sanding belt length 2600 mm 3 kW motor 2 additional motors for height adjustment and oscillation With feed system Weight approx. 400 kg Location: in stock at 54634 Bitburg - immediately available -

Year of construction: 1998, condition: excellent (used), used Fedpfx Ajd I Id Hel Ujpn Year: 1998 Start type: to be agreed Cost of delivery: Customer cover Conditions of delivery: OWN RECEIPT Category: Saws in Poland Subcategory: Longitudinal saws for veneer

Condition: good (used), Code: 0351 Fpsdjy A Sq Tepfx Al Usn Brand: VOLPATO Model: LS - 1N - CE Standard Automatic edge sanding machine for edges and profiles in wood, solid wood, veneer, painted and various materials - CE Standard Technical data Max working height mm 110 Min working length mm 100 Variable-speed belt feed 5–30 m/min – Motor Kw 1,5 Tilting oscillating sanding unit – 2-speed motor 700–1400 rpm – Power 2 Hp Pneumatic belt tensioner – Timed entry and exit of the pad Mechanical oscillation of abrasive belt 0/20 mm Lifting and tilting via handwheel with special key Removable support for large panels Abrasive belt dimensions 80 x 2450 mm Suction inlet diameter 100 mm Compressed air 5–6 atm Overall dimensions mm 2600 x 1400 x 1500 h Weight kg 720

Year of construction: 2015, operating hours: 1,000 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: M15090L, For sale is a high-quality vacuum membrane press from Columbus Presstechnology. Fjdpfx Aoy I Ugujl Uepn Type: Multimat Sonder Model: M15090L Year of manufacture: 2015 The machine is in good, well-maintained condition and is immediately ready for operation. Technical data: Voltage: 400 V / 50 Hz Power: 19 kW Suction capacity: 40 m³/h Vacuum: up to -0.9 bar Temperature range: up to 140 °C Equipment / Condition: Fully functional and ready for use Robust industrial design Membrane included (used but functional condition) User-friendly controls Ideal for woodworking, furniture, or plastics processing Applications: Veneering Foil lamination Mold making / plastics processing Prototype production Inspection is possible – the machine is ready for use.

Year of construction: 2026, condition: new, functionality: fully functional, Vacuum Press / Membrane Press “Columbus Pioneer” – Available for Immediate Delivery! (Modular system with various configurations and usable surfaces) – now including a digital Master Manual and AI support on tablet for a safe start and reproducible results. The COLUMBUS Pioneer is a professional vacuum and membrane press for applications such as vacuum form-bonding, veneering, coating, and laminating of flat or curved workpieces. Thanks to its modular concept, the machine can be adapted to different requirements and is available in various sizes and configurations. Technical Features: • Quick-change membrane system • Gas pressure dampers for comfortable lid opening Fsdpfxjz Izz Ho Al Uopn • Highly elastic natural rubber membrane (up to +130 °C) • Durable phenolic resin worktop, 15-ply bonded (up to +120 °C) • BECKER high-performance vacuum pump, 40 m³/h (up to 900 mbar / 9 t/m²) • Optional automatic shut-off upon reaching set pressure • Pressure regulation 400–900 mbar with analogue vacuum gauge • Connection for external vacuum bag • Base feet with smooth-running swivel castors • FESTO pneumatic components and SIEMENS electrical systems Available Working Areas: 3,050 mm x 1,350 mm (Pioneer L) 4,050 mm x 1,350 mm (Pioneer XL) 4,050 mm x 1,700 mm (Pioneer XXL) Designs/Modular Configuration: The COLUMBUS Pioneer features a modular design and is available in BASIC (classic vacuum pressing such as veneering, coating, and form-bonding), HEAT (heating and thermoforming of plastics and solid surface materials), and VERTICAL (processing of taller workpieces and convenient loading/unloading via vertical opening) versions, which can be combined or retrofitted depending on requirements. COLUMBUS machines are designed for long-term operation and are manufactured using high-quality industrial components. The robust construction, proven components from renowned manufacturers, and precision workmanship ensure high durability and reliable performance. COLUMBUS offers a lifetime warranty on the machine frame (excluding wearing parts). Every COLUMBUS Pioneer is part of the COLUMBUS 360° System. This includes the digital Master Manual with extensive practical vacuum technology knowledge and Master GPT – an artificial intelligence for all questions regarding the machine, applications, materials, and optimal process parameters. The system assists users with setup, operation, and process optimization, and comes with a tablet for immediate use.

Condition: new, Table for hard cover making 1050×740 The device is brand new, with a 12 month warranty. European production, based on brand-name components. Work cycle: The operator manually hands the covering material to a gluing device in which the animal glue is automatically applied (working temperature 60-70’C). The covering material sheet with the glue applied, the operator places it manually on the stage, then manually adds the cardboard and joint board sheets. The operator prepares the pre-prepared cover manually to the device in which the top and bottom of the covering material are wrapped up and glued (patented brush system). During the sizing operation, the cover is pressed through the arrangement of the guide rollers. Fjdpfx Ajz N Shzel Uopn Covers leaving the device are immediately suitable for further processing The machine is equipped with: – A gluing machine applying glue to the top of the sheet – table with a suction – fixing elements for covering material and cardboard – a module for wrapping the cover – receiving table Technical data: Max format: 1050x740mm Min format: 140x140mm Capacity: 100-150 covers / h Thickness of the layer: 80-170 gsm Thickness of cardboard: 1-4mm Wrap up: 13-20mm Temperature of the adhesive: 30-100 ‚C Capacity of the bender: 2-3kg Smooth speed control of rollers and brushes Types of veneer material: fabric, laminated paper, photographic paper, imitation leather, PVC, polyurethane. Dimensions of the machine: 1600x1800x1000mm Power supply: 380V Power consumption: 3.7kW Weight: 300kg We invite you to tests to our headquarters Machines are available from stock.