Used Weber Cr 6 for sale (106)

Condition: used, Vibratory Feeder with Pneumatic Screwdriver Stand Eco Line Vibratory Feeder, Sorting Device, Bowl Feeder, Vibratory Bowl, Automatic Screwdriver WEBER Type ZSU 24 Machine No.: 1113212 Year of Manufacture: 2003 Bodpfexf Up Ujx Afasdi Vibratory Feeder WEBER ZSU 24 Bowl diameter: 240 mm Bowl internal height: 70 mm Sorting track width: 10 mm Power supply: 230 Volt, 50 Hz Operating pressure: 6 bar (for singulation and screws) Control voltage for pneumatic valves: 24 Volt - Controller for infinitely variable vibration speed = infinitely variable transport speed - Vibratory bowl in protective enclosure - With pneumatic feeding system - Feed impulse via external electrical control - The feeder was used for feeding screws M5 x 12 mm - Some pneumatic hoses need to be replaced - Siemens S7-200 CPU 224 PLC MISSING Space requirements vibratory bowl L x W x H: 450 x 450 x 315 mm Vibratory bowl weight: 32 kg WEVER Eco Line Screwdriver Stand Guide column: Ø 60 x 525 mm Height adjustment: 345 mm Primary stroke pneumatic cylinder 1 FESTO DZF-32-125-P-A-SM: 115 mm Screwdriver holder diameter: Ø 50 mm Secondary stroke pneumatic cylinder 2 FESTO: 30 mm Screwdriver guide diameter: Ø 37 mm Distance screwdriver guide to table: 135 - 465 mm - 1 piece flat cylinder FESTO, Type DZF-32-125-P-A-SM - 1 piece flat cylinder FESTO, Type probably DZF-32-30-P-A-SM - Screwdriver linear motion frame on linear guide - 3 position sensors on the cylinders - Festo pressure switch - Bosch pneumatic valve Screwdriver stand dimensions W x D x H: 200 x 410 x 1050 mm Screwdriver stand weight: 35 kg good condition Total weight vibratory feeder and screwdriver stand: 67 kg Attention: The original Siemens S7-200 CPU 224 PLC is missing (see picture control cabinet without PLC), therefore, an automatic process is not possible in this condition. The control system also managed the separations of the screws and controlled the screwdriver itself. The vibratory bowl is fully functional even without the PLC, the built-in vibratory bowl controller does not require PLC control. Process: Fasteners are filled into the bowl in bulk and conveyed upward by mechanical vibration (micro-throw principle). The vibratory bowl is automatically switched on or off depending on the fill level of the screw magazine. The screw is then conveyed by compressed air through a plastic hose to the downstream device. The feed impulse for each individual screw is triggered externally by the downstream device.

Condition: good (used), For sale: a complete set of Weber-Hydraulik hydraulic rescue tools. The set includes a SP-40 hydraulic power unit, cutters, and a spreader. The entire set is mounted on a metal transport frame and equipped with reels containing hoses. The set has been inspected and is in 100% working order. The visual condition and detailed scope of equipment are shown in the photos. Data read from the nameplates: Power unit manufacturer: Weber-Hydraulik Bdodsz Skyiepfx Afaji Power unit type: SP-40 TÜV marking: SP32-95-TP18/SP30 Engine: ATB AKF 90S/2F-12R Engine power supply: 230 V, 50 Hz Engine power: 1.3 kW Rotational speed: 2760 rpm Engine protection rating: IP54

Year of construction: 2025, condition: refurbished (used), functionality: fully functional, Container conveyor scale, electronic, pneumatic, bulk material scale, 60 tons/hour. Calibratable, year of manufacture 2025 (all electrical and pneumatic components have been completely overhauled). For fine-grained bulk materials such as grain, high measuring accuracy. Ideal for goods receiving and loading. High throughput capacity, dust-proof frame construction. Purchased to replace a mechanical conveyor scale, but not installed due to the short-term shutdown of operations. Pre-hopper with level indicator also available. Bdedpfx Afozy Rcyeaoi

Year of construction: 1994, condition: used, weight 2,2 t Bodpfx Afsx U A Iasaodi extruder diameter x mm x +++++ Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. +++++

Condition: used, functionality: unexamined, Adapter for extruder Weber DS-85 Bsdpfx Afezzwi Aoasdi Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Condition: used

Condition: used, functionality: fully functional, fuel type: gasoline, overall weight: 32 kg, DGUV certified until: 03/2026, Year of construction: 2018, machine/vehicle number: 20008074, Equipment: UVV, Specifically designed for compaction of pipe collars in trenches. Other areas of application: compacting edge zones of walkways; installation of drainage systems. Due to its low weight, it is easy, flexible, and safe to operate even on slopes and in very confined spaces. Bdedjxpu Tbepfx Afasi

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, WEBEN / CEEVER Washing Tunnel with Robot, Conveyor, and Inspection System Manufacturer: WEBEN / CEEVER Application: Automated parts handling downstream of a press (press not included), washing, drying, and quality control Description: This system is an automated solution for retrieving and transferring parts from an upstream press. Robots pick up the parts and move them via a conveyor and transport system through an industrial washing tunnel (wet cleaning), followed by an inspection/measuring system for quality assessment. The complete process chain is designed for continuous operation, integrating robotic handling, washing process, conveyor technology, and automatic quality decision (OK/NOK). Technical Specifications – Washing Tunnel Year of manufacture: 2021 Cleaning process: spray-spray system (water-based), air blow-off, hot air drying Max. workpiece dimensions: length 1,400 mm Max. workpiece dimensions: depth 2,000 mm Max. workpiece dimensions: height 10 mm Max. workpiece weight: 12 kg System dimensions: width 3,000 mm System dimensions: depth 35,500 mm System dimensions: height 3,400 mm Weight (empty): 20,000 kg Weight (operational): 27,000 kg Material in contact with media: stainless steel AISI 304 Washing tank volume: 4,000 liters Washing tank heating: electric 80 kW Rinse tank volume: 2,500 liters Rinse tank heating: electric 40 kW Washing pump: 2,000 l/min, 6 bar, 30 kW Rinse pump: 900 l/min, 6 bar, 15 kW Washing filtration: 4 bag filters, 100 µm Drying: electric 48 kW Electrical connection: 380–400 V / 50 Hz / 3 Ph + N Total connected load washing tunnel: 385 kW Compressed air for automation: 6–8 bar, 1/4" connection Compressed air blow-off: 6–8 bar, 4 connections, approx. 30,000 Nm³/h consumption, 1 1/4" connection Technical Specifications – Robot, Conveyor, and Inspection System Control: Siemens PLC S7-1500 1517F Operator panel: Siemens TP1900 Comfort Robot: KUKA KR50 R2500 IONTEC with KRC4 (multiple robots in line) Conveyor technology: multiple conveyor lines / transport zones Max. conveying speed: up to 24 m/min Inspection system: laser measuring system with automatic OK/NOK evaluation and sorting Bdsdpfxjy Ein Us Afaji Location: EU

Condition: used, Year of construction: 1995, Constant machine - combination station, dust brush - thickness measuring device - electronic segmented sanding pad MCS System Weber 32 mm - grooved steel calibrating roller - belt blow-off - vacuum conveyor belt. Sanding width: 1100 mm Drive: 15 kW Feed approx. 1.1 kW Height adjustment 0.25 kW Sanding belt dimensions: 1150 x 2500 mm Max. workpiece thickness: 150 mm Machine width: 1700 mm Machine length: 2000 mm Machine height: 2160 + 150 mm Machine weight: 1900 kg Constant working height: 850 mm Extraction connector: belt 180 mm / brush 120 mm Suction air volume: 0.74 m³/s Connected load: 23 kW Compressed air supply: 7 bar Feed speed: 3-15 m/min. Operating hours: 7000 h Location: Nattheim Bdsdpfxjx Twcpe Afasi

Condition: excellent (used), DOUBLE SCREWS for WEBER DS105.17D EXTRUDER Application: PVC PIPES SCREW NUMBER: 014.185605 r.920 S Screw diameter: 104.7 mm and 104.8 mm Bsdpjywr Tdefx Afaodi

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, power: 44.7 kW (60.78 HP), Technical Data: Operating height: 900 mm Operating width: 1350mm Max. workpiece thickness: 99mm Min. workpiece thickness: 0.8mm Dimension of the machine: Weight: approx. 4800kg Width: approx. 2800mm Length: approx. 3460mm Height: approx. 2440mm Bdsdpfx Afswnw E Tjaei We bought the machine in 2020 and refurbished it. It comes with a new conveyor belt.

Condition: good (used), Year of construction: 1991, Brand: Hans Weber GmbH Bdsdpfx Aezu Nl Asfaei Model: DS 120 Year of manufacture: 1991 Screw diameter: 120 mm • One pair of original WEBER screws (in excellent condition, including measurement report) • One pair of non-original screws • Gearbox inspected and partially overhauled by WEBER • Control system upgraded to WPS control • Output on PVC approximately 700 kg/hour

Condition: ready for operation (used), Year of construction: 1995, operating hours: 39,000 h, functionality: fully functional, Equipment: documentation/manual, A used and functional profile line for rigid PVC-profiles (300 x 100 mm), consisting of: Twin-screw extruder (parallel) Manufacturer: WEBER Type: DS 7.22 Year of manufacture: 1995 Machine no.: DS70-043 Operating hours: 39,000 hours Screw diameter: 70 mm Effective screw length: 22 x D Screw geometry: for rigid PVC profiles Torque: 4,500 Nm per screw Screw speed: max. 40 rpm, continuously adjustable Drive motor: DC low-voltage motor, thyristor-controlled Drive power: approx. 25 kW Cylinder heating/cooling zones: 5/3 (air cooling with fan) Adapter heating zone: 1 Tool heating zones: 5 Control: conventional control with digital temperature controllers Degassing: Busch rotary vane vacuum pump (1.5 kW) Output capacity, max.: 120-150 kg/h for hard PVC, depending on material Connected load: approx. 50 kW (without tool) Special accessories: Mass temperature sensor and mass pressure sensor Adapter between extruder connection and extrusion tool Used tool set for a window profile (widening), consisting of: - Extrusion tool ‘widening’, incl. heating bands - Dry calibration Bdedpfxsyhcabo Afasi - Vacuum tank approx. 2 m long, with 8 slots for calibration discs - 16 calibration discs Vacuum calibration unit Manufacturer: Uniplast / Greiner Type: CAL VAK 4P Year of manufacture: 1992 Machine number: K9209590 Total length: 6500 mm Vacuum pumps: 4 x Speck vacuum pumps (4.3 kW each) Water circulation pumps: 2 x Calpeda (1.1 kW each) Caterpillar haul-off, incl. attached saw Manufacturer: Uniplast / Greiner Type: CAT PUL 2D Year of manufacture: 1992 Machine number: R 9204546 Haul-off: Effective contact length: 2000 mm Pad width: 250 mm Haul-off force, max.: approx. 25000 N Speed range: approx. max. 10 m/min. Profile saw: HM circular saw blade: Ø 450 mm Profile cross-section, max.: approx. 300 x 100 mm Tilting table Manufacturer: Ide Type: ME N 52/2 Year of manufacture: 1994 Length: 6000 mm Support width: 270 mm Note: The complet profile line was overhauled in 2020 and has only been in operation for 325 hours since then.

Condition: used, mileage: 1,001 km, power: 4 kW (5.44 HP), gearing type: other, fuel type: diesel, color: yellow, first registration: 01/1999, Year of construction: 1999, driver cabin: other, Vehicle location: Bovenden, Hatz Diesel Engine E 673LS! Forward and reverse gear! The exact year of manufacture and power output cannot be determined as there is no type plate present! Equipment details provided without guarantee; subject to change, prior sale, and errors! Bedpfsxy Swxox Afaodi

Condition: good (used), Rear axle, steering axle, forklift axle, steering cylinder, hydraulic cylinder, support cylinder, hydraulic ram, pressure ram, tilt cylinder, lifting cylinder, tie rod cylinder, tilt cylinder -Manufacturer: Weber Hydraulik, hydraulic cylinder tilt cylinder stroke 110 mm Bodpfxsv Tahio Afajdi -Type: Clark 4334896 -Piston rod: Ø 35 mm / M30 -Dimensions: Ø 88 x 420 mm -Weight: 8.7 kg

Condition: new, Diamant Weber WM 306791 A/R0 3 Diamond tool, serial number as shown in the photo, unused in original packaging, 100% functional, scope of delivery as shown in the photos. Bedpei D Upkofx Afaodi

Condition: used, Weber Loading Conveyor Model CZB Stainless steel Bdedpjxtfz Refx Afaji

Condition: good (used), Year of construction: 1994, Model: NE 12 Screw type: Single screw Year of construction: 1994 Screw diameter: 130 mm Bjdpfoyxpbuex Afasdi L/D ratio: 30 L/D Drive power: 350 kW Including: • Machine was in production when dismantled • Machine was producing 710 mm pipes • Output on HDPE approximately 1,000 kg/hour • 800 mm extrusion head

Condition: new, functionality: fully functional, power: 2.7 kW (3.67 HP), fuel type: gasoline, color: blue, operation weight: 62 kg, Year of construction: 2026, motor manufacturer: Honda, Equipment: UVV, Weber SRV 590-II Rammer – NEW | 700 blows/min | 62 kg operating weight | 280 mm shoe width | Honda GXR 120 petrol engine with 2.7 kW Item number: WEB170160 Technical Data: Manufacturer: Weber MT Bedpfj Ahfd Isx Afajdi Model: SRV 590-II Condition: NEW Operating weight: 62 kg Blows per minute: 700 min⁻¹ Shoe width: 200 mm or 280 mm Engine: Honda GXR 120 petrol engine Engine output: max. 2.7 kW Fuel: Petrol Starting system: Recoil start Features & Equipment: - Proven rammer for professional compaction applications - Reliable Honda GXR 120 engine – powerful & durable - 200 mm or 280 mm shoe width – ideal for trenches & confined job sites - High impact rate for efficient compaction - Compact & robust design – optimal for construction site use - Quality by Weber MT – immediately available Applications: ✓ Cable & pipeline construction ✓ Landscaping & gardening ✓ Compaction in trenches & narrow areas ✓ Municipal operations & construction companies ✓ Fiber optic & network installation Location: Warehouse D 46514 Schermbeck (NRW) – Inspection & collection possible Delivery across Germany & internationally on request Pricing ex works Maassenstraße 91, D 46514 Schermbeck (district of Wesel) All information subject to change. Errors and prior sale excepted. Prices plus VAT / VAT excluded Further models available! SRV 620, SRV 660, etc. also in stock ➡️ New & used machines, accessories & spare parts Buy Weber Rammer | SRV 590-II NEW | Petrol Rammer | Honda GXR 120 | 280 mm shoe width | Weber MT Compaction Technology Your reliable partner for compaction technology & construction equipment: Claudio Macagnino Baumaschinen & Nutzfahrzeughandel GmbH ➡️ Contact us now & secure immediately available new equipment! On request, we are happy to offer you a virtual machine inspection via video call.

Condition: used, mileage: 1,001 km, power: 2 kW (2.72 HP), gearing type: other, fuel type: gasoline, color: blue, empty load weight: 62 kg, first registration: 01/2018, Year of construction: 2018, driver cabin: other, Vehicle location: Bovenden. Honda GX R120 petrol engine! Accessory specifications provided without guarantee; subject to changes, prior sale, and errors reserved! Bedpfx Afexy Swrjaodi

Condition: used, Year of construction: 1990, Used Weber wide belt sanding machine with 2 sanding belts, oscillating. Infinitely variable feed speed. Sanding width 900 mm. Used as a backup machine. Bdjdswzlqkjpfx Afaei

Year of construction: 2001, condition: excellent (used), Single screw extruder WEBER NE5 1-30:D with 2 co-extr. WEBER ZE30 Year of construction 2001 Screw diameter 50 mm Application:PE-PP, Three-layer pipes or pipes with colored stripes The plant has manufactured heating pipes Condition: very good 2 Co-Extruders WEBER ZE30 Screw diameter 30mm The three-layer pipe system is my property Location: Sachal EXTRUSIONSMACHINEN D-26345 Bockhorn/Grabstede, Germany Bsdpfxshy Tp Do Afasdi

Condition: like new (used), Extruder hose sections for Weber DS 10.22. Bdsdjhlvm Nepfx Afasi

Condition: like new (used), Quantity: 2 2x WEBER DS 88 - 17D complete original processing units Complete conversion kit from the old degassing position to the upstream degassing position - suitable for PVC window recipes, dryblend processing - Enlarged preheating zone - all parts unused in original packaging Location: Pirmasens Bedot H Rrzepfx Afasdi We will be happy to send you further information on request.

Condition: good (used), Hydraulic cylinder, support cylinder, hydraulic piston, pressure piston -single-acting cylinder -Cylinder: Ø 100 mm -Piston rod: Ø 48 / Ø 36 mm -Pipe outer diameter: mm Bdedpfx Aeb A I Hisfaji -Stroke: 500 mm -Total length when retracted: 570 mm -Ideal for building a hydraulic press -Number: 8 available -Price: per piece -Weight: 10.5 kg/piece

Condition: ready for operation (used), Year of construction: 1998, travel distance X-axis: 3,000 mm, travel distance Y-axis: 2,500 mm, travel distance Z-axis: 1,500 mm, table load: 20,000 kg, spindle speed (max.): 3,500 rpm, number of axes: 3, This 4-axis Burkhardt-Weber MC100 was manufactured in 1998. It features a working range with an X-axis travel of 3,000 mm, Y-axis travel of 2,500 mm, and Z-axis travel of 1,500 mm. The machine has a maximum table load capacity of 20,000 kg and a spindle speed of 3,500 RPM. If you are looking to get high-quality milling capabilities, consider the Burkhardt-Weber MC100 horizontal machining centre we have for sale. Contact us for further details. • B-axis (NC rotary table): 360° continuous • Tooling standard: High-torque configuration for large-scale milling • Additional notes: Bjdpfxjzg Il Es Afaedi • Retrofitted in 2008 Technical Specification Taper Size BT 50