Overhauled ORT RP18 B PLC

ORT RP18 B PLC

Year of construction: 1985, condition: reconditioned (used), Technical Details : Wire Dimeter range- 4-12mm Gscxckebw Run out table - 4m Hsdoh In Thspfx Afgow Speed -80' m/min. Reconstruction- 2022

Condition: good (used), Centerless grinding machine HERMINGHAUSEN SR40 III CNC Hjdpfx Afsgq Ddfsgjw

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Hodpfx Ajuz If Nefgow Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: good (used), Rotary vane vacuum pump /// Oil-lubricated Manufacturer: Busch Type: RC 0100B Hjdjbrantjpfx Afgjw Ultimate pressure: approx. 20 mbar Pumping speed: approx. 100 m³/h Condition: General overhaul If you have any questions about this listing or general questions about vacuum generation, please do not hesitate to contact us.

Condition: new, Precision, quiet, and reliable drill press. Built according to strict safety standards. Precision spindle with hardened Morse taper and machined base plate. Electronic speed control included. Rotating table + vise, 350 x 250 mm. Drilling capacity in steel: R50 mm, ø 22. Tapping capacity in steel: R50 mm, M14. Spindle taper: CM2. Spindle stroke: 90 mm. Spindle bore diameter: 52 mm. Column diameter: 98 mm. Distance from column to spindle center: 201 mm. PU transmission. Hjdpfx Aeir Aihofgow Electronic speed control (E). Spindle speed: 270 ÷ 4,200 rpm. Motor power: 0.75 kW / 220 V, single-phase. Dimensions (h x w x d): 1950 x 600 x 680 mm. Weight: 220 kg.

Condition: good (used), Rolling pressure 220 kN Ø Pieces 3mm min; 70mm max Pitch 6mm max Grooving pitch 2.25mm max Roller width 160mm max Ø Roller 133mm min; 170mm max Roller shaft speed 24 30 38 45 62 72 90 114 rpm Ø Roller carrier shaft 54mm standard; 69.85 special Hjdpovyyyxsfx Afgjw Distance between shafts 135mm min; 230mm max Working stroke 15min max Feed rate 0.5mm/s to 6mm/s Laminating time 0.1s to 100s Pause time 0.1s to 100s Main motor 5.5 Kw Electrical power consumption 8.6 Kw Tank capacity 130 L Weight approx 2100 Kg

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate Hedpfxjk S Htxe Afgjw - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition

Condition: excellent (used), Spot welding machine with single-acting cylinder and flange-mounted electrode holders above and below Make: DALEX Type: PMS 14-3 Throat depth: 350 mm Rated power at 50% duty cycle: 80 kVA Secondary short-circuit current: 54.5 kA Secondary open circuit voltage: 7-14 V Electrode force: 80-1,200 daN Equipped with: 8-step switch Main switch Attached control cabinet HARMS+WENDE Synchronous welding control MPS 200 8 welding programs with AEG nameplate Hedpfetuwz Ijx Afgjw Start via foot pedal

Condition: good (used), Year of construction: 2006, operating hours: 9,911 h, functionality: fully functional, travel distance X-axis: 450 mm, travel distance Y-axis: 270 mm, travel distance Z-axis: 310 mm, rapid traverse X-axis: 75 m/min, rapid traverse Y-axis: 75 m/min, rapid traverse Z-axis: 75 m/min, nominal power (apparent): 17 kVA, total height: 2,300 mm, total length: 1,500 mm, total width: 2,600 mm, overall weight: 3,400 kg, spindle speed (max.): 30,000 rpm, spindle nose: HSK40, number of slots in tool magazine: 40, input voltage: 400 V, Equipment: documentation/manual, CNC machining center CHIRON FZ08 KS Magnum High Speed Plus (HSP) TECHNICAL CHARACTERISTICS: Year of manufacturing: 2006 Hjdpfxox Iiw Io Afgew CNC control : FANUC 18i-MB5 Number of axes : 7 Stroke X axis : 450 [mm] Stroke Y axis : 270 [mm] Stroke Z axis : 310 [mm] Traversing feeds X, Y and Z axes : 75000 [mm/min] Max. bar diameter in turning spindle : 32 [mm] Main spindle max. speed : 8000 [rpm] Main spindle max. power : 12 [kW] Angular A axis stroke : 360 [°] A axis indexing precision : 0.001 [°] B axis swivelling stroke : -20° / +115 [°] B axis indexing precision : 0.001 [°] Spindle type : HSK40 Max. spindle speed : 30000 [rpm] Tool changer magazin number of stations : 40 Part turnaround by robot (6th side machining) : Yes RS232 Interface : Yes Total power required : 17 [kVA] Supply voltage : 400 [V] Number of running hours : 9911 [h] Dimensions : 1500 x 2600 x 2300 [mm] Weight : 3400 [Kg] EQUIPMENT INCLUDED: x1 RENISHAW TS27R tool probe x1 spindle cooling unit x1 parts catcher x1 coolant tank x1 unit for 6th face machining (gripping system not included) x29 tool holders type HSK40 BIG KAISER x10 collets type F37 SCHAUBLIN x1 washing gun x1 3-color status light x1 maintenance manual x1 electrical diagrams manual x1 operator's manual x1 programming manual Price on request, loading on truck included. Possibility of shipping Worldwide. The information on this page has been obtained by the best of our ability. Therefore, its accuracy can not be guaranteed Machine similar to brands such as Okamoto, ELB, GER, Tacchella, Karstens, Jones & Shipman, Jung, Favretto, Blohm. Internal and external grinding (ID/OD) also to be considered. Surface grinder, lathe, machining center, milling machine.

Condition: good (used), Year of construction: 2001, Machine is in good condition. Parts shown by hand not come. Hsdpfx Aforpk Rmsgjw Cutting tools not come.