Center lathe

WEILER Matador VS

Condition: used, turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - very good condition (!!) regularly receive a WEILER factory service particularly suitable for medium-precision turned parts Njdpfx Afoxacgdeusdb Equipment: - robust lead/pull spindle lathe - KLOPFER four-jaw chuck Ø 140 mm - KLOPFER three-jaw chuck Ø 140 mm - collet holder with lots of collets - foldable lathe chuck guard - chuck key - MULTIFIX steel holder A, with 3x new inserts - movable tailstock - control panel, front left - automatic feeds for face and top support - pole-changing drive motor - machine base frame, with cabinet door (storage area) - chip splash guard rear wall - emergency stop button, bottom right - machine swing feet - original operating instructions

Condition: ready for operation (used), turning length 450 mm turning diameter over bed 245 mm turning diameter over slide rest 135 mm spindle bore 23.0 mm tool adaptor DIN 55021-4 quill: 2 MK quill travel 80.0 mm turning speeds 60 - 3000 U/min bed width 155 mm total power requirement 1.2 / 1.5 kW voltage 380 V weight of the machine ca. 340 kg. Ndsdpfxszbc Dte Afusb range L-W-H 1200 x 650 x 1330 mm from a vocational school (!) particularly suitable for precision turned parts The Primus series is the most compact precision sliding headstock and sliding headstock lathe (LZ) from WEILER. It is used in toolmaking, laboratories and training workshops as an absolute machine for precise work in the tightest of spaces. The machine is built for extremely tight tolerances. The hardened and ground machine bed ensures maximum for maximum vibration damping and durability. Features: - Robust lead/traction spindle lathe - 2-axis digital readout "D60-2V" - three-jaw chuck - Folding lathe chuck guard - chuck key - MULTIFIX steel holder with 3x inserts - Sliding tailstock - Control panel, front left - infinitely adjustable feeds for flat and top support - Pole-changing drive motor - machine base frame - Chip guard rear panel - Additional accessories such as collet holder Collets etc. - EMERGENCY OFF button at the front

Condition: ready for operation (used), turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - in very good condition (!!) particularly suitable for medium-precision turned parts Features: - Robust lead/feed screw lathe - RÖHM three-jaw chuck Ø 160 mm Ndedpjxq Hhyefx Afusb - Foldable lathe chuck guard - Chuck key - MULTIFIX steel holder A, with 3x new inserts - Movable tailstock - Swiveling machine light - Control panel, front left - Automatic feeds for face and upper support - Machine base, with cabinet door (storage space) - Chip splash guard rear panel - Emergency stop button - Operating instructions

Condition: used, turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - very good condition (!!) regularly receive a WEILER factory service particularly suitable for medium-precision turned parts Equipment: - robust lead/pull spindle lathe - KLOPFER four-jaw chuck Ø 140 mm - collet holder with lots of collets - chuck key - MULTIFIX steel holder A, with 3x new inserts - movable tailstock Ndsdsxaccxepfx Afusb - adjustable bed stop - control panel, front left - automatic feeds for face and top support - pole-changing drive motor - machine base frame, with cabinet door (storage area) - chip splash guard rear wall

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, total height: 325 mm, total width: 185 mm, total length: 483 mm, overall weight: 16 kg, type of cooling: water, electrical fuse: 16 A, welding current at 100% duty cycle: 175 A, welding current (min.): 5 A, welding current (max.): 250 A, Equipment: documentation/manual, type plate available, Complete set: LORCH T 250 DC Basic Plus TIG welding machine with WUK 7 water cooling system and accessories. For sale is a professional industrial welding machine from the premium brand LORCH, model T 250 DC Basic Plus, combined with the innovative water cooling unit WUK 7. The system is designed as a mobile all-rounder as well as a fully functional workshop device and features state-of-the-art inverter technology. Manufacturer: LORCH (Made in Germany) Model: T250 DC Basic Plus incl. optional WUK 7 water cooling Condition: very good, fully functional Location: Graz _____ Scope of delivery (Full Set): • LORCH T 250 DC Basic Plus TIG inverter welding machine • LORCH WUK 7 water cooling unit (direct LorchNET connection) • TIG welding torch incl. hose set • Ground cable • Maintenance unit for gas / pressure regulator _____ The new price was approximately €6,000 _____ Highlights: • Innovative single-cable solution: Thanks to the modern cooling unit connection, the entire system (inverter + water cooling) now only requires a single power cable. The power supply and intelligent, demand-based control of the WUK 7 is carried out directly via the back of the welding power source. No cable clutter during assembly! • High-end inverter technology: Full 250 A welding power in a compact design. • FastPuls function (up to 2 kHz): Perfect for distortion-free welding of extremely thin sheets. • Robust mobility: Extremely lightweight base unit (only 16 kg), ideal for demanding applications in vehicle construction, metalworking, and tank and pipeline construction. _____ Technical data: • Power range: 5 – 250 A • Duty cycle (ED) at 40°C: 60% = 200 A / 100% = 175 A • Mains voltage: 400 V (mains fuse 16 A) • Cooling capacity (WUK 7): 0.53 kW Ndodpfxeyxvwie Afujb • Weight: approx. 16 kg • Dimensions welding inverter Lorch T 250 DC: 483 x 185 x 325 mm (L x W x H) • Dimensions water cooling unit Lorch WUK 7: 547 x 212 x 265 mm (L x W x H) _____ The device is in a ready-to-use condition. Inspection and test run can be arranged.

Condition: used, turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - very good condition (!!) regularly receive a WEILER factory service particularly suitable for medium-precision turned parts Equipment: - robust lead/pull spindle lathe - KLOPFER four-jaw chuck Ø 140 mm - KLOPFER three-jaw chuck Ø 140 mm - collet holder with lots of collets - foldable lathe chuck guard - chuck key - MULTIFIX steel holder A, with 3x new inserts - movable tailstock Nsdpfx Afsxaciroujdb - adjustable bed stop - control panel, front left - automatic feeds for face and top support - pole-changing drive motor - machine base frame, with cabinet door (storage area) - chip splash guard rear wall - emergency stop button, bottom right - machine swing feet - original operating instructions

Condition: ready for operation (used), WEILER Matador VS 2, including a new three-axis digital display, from a school workshop. -Maximum distance between centers: 140 mm -Distance between centers: 500 mm -Spindle speeds: 15 - 3550 rpm -Automatic longitudinal and cross feeds -Threading capabilities: metric, inch, etc. -New three-axis digital display -Electric chuck guard -Work light -Multifix base with inserts -Coolant system -Three-jaw chuck / collet chuck -Tailstock MK 3 -Various tools -Documentation Dimensions: L x W x H: 1.5 x 0.6 x 1.5 meters / Weight: 680 kg Errors and omissions excepted. Nedpfozr Rnysx Afuodb

Year of construction: 1972, condition: ready for operation (used), Spindle-to-table distance min./max.: 81mm/481mm, counter support spindle center distance: 195mm, spindle head swivel: 360°, milling spindle diameter: 70mm, spindle adjustment: 100mm, headstock adjustment: 300mm, table dimensions X/Y: 480mm/820mm, travel X/Y/Z: 500mm/200mm/400mm, max. workpiece length: 400mm, spindle speed: 1600rpm, feed X/Y: 500mm/min, feed Z: 250mm/min, spindle head swivel: +/-30°, machine dimensions X/Y/Z: approx. 1600mm/2550mm/1700mm, weight: approx. 2300kg. The machine was electrically tested at the end of 2025 and a defect of the emergency stop switch was discovered. Documentation available. On-site inspection is possible. Ndedpfx Afox S Rcmoujb

Condition: used, Year of construction: 1971, turning diameter over bed 297 mm turning diameter over bed slide 160 turning length 500 mm short taper holder Größe 5 spindle bore 36 mm spindle turning speed range 30-3550 U/min number of speeds 18 quill adjustment 90 mm tailstock quill taper MT 3 cross adjustment +15 tailstock adjustment - manual 500 mm weight of the machine ca. 610 kg dimensions of the machine ca. 1,4 x 0,7 x 1,2 m cessories: Forkardt V-block chuck, Ø 160 mm Collet chuck, Collets (see photo) Steel Multifix system, size A with 3 quick-change inserts rotating center point chip guard chuck guard Ndodpsy Hxp Dsfx Afueb fixed steady rest The machine comes from the training workshop of a renowned German corporation.

Condition: ready for operation (used), functionality: fully functional, Distance between centers: 500 mm Center height: 160 mm Spindle bore: 36 mm Spindle speed: 56 – 2000 rpm Tailstock: MT 3 Drive power: 2.4 kW Weight: 650 kg Dimensions: 1,400 x 700 x 1,220 mm Digital readout: Optional at extra cost Ndsdpfx Afeypbypjusb Accessories: Additional accessories available on request!

Condition: used, Year of construction: 2003, centre height 255 mm centre distance 1.080 mm turning diameter over bed 500 mm turning diameter over slide 290 mm turning length 1.000 mm control EuroTurn spindle bore 70 mm spindle taper KK 8 DIN 55027 3-jaw-chuck diameter 250 mm bed width 360 mm Ndedpfx Afewizltouob turning speed range 2 - 2.800 U/min rapid travel - longitudinal/face 10 / 5 m/min quick change toolholder PARAT Gr. 2 drive capacity - spindle motor 11,0 kW taper in tailstock-quill MK 5 dia. of quill 80 mm quill stroke 160 mm voltage 400 V total power requirement 16,0 kVA weight of the machine ca. 3,0 t dimensions of the machine ca. 2,85 x 1,60 x 1,80 m - Serial-No.: 495 / 03 - control: EuroTurn - quick change tool holder PARAT - coolant equipment - machine lamp

Condition: excellent (used), functionality: fully functional, Weiler Matador VS-2 lathe with lead screw and tailstock, equipped with a 3-axis digital display from Heidenhain ND 780, from a training workshop!! Technical data: >> Machine No. 7702, year of manufacture approx. 1990 >> Center height 140 mm >> Center distance 500 mm >> Speed: 15 – 3550 RPM >> Spindle bore 36 mm >> Short taper spindle head DIN 55022-5 with bayonet fitting Ndedey T Hqcspfx Afujb >> Tailstock MK 3 >> Feeds from 0.012 to 0.9 mm/rev >> Possible threads: metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 12 mm >> Brake motor >> Weight approx. 700 kg >> Length 1.4 m, height 1.2 m, depth 0.55 m Accessories and equipment: >> 3-axis digital display Heidenhain ND 780 >> Quick-change tool holder, internal and external collets (see picture) >> 1 three-jaw chuck, 3 sets of jaws >> Mulifix size A with 3 steel holders >> Spindle guard >> 1 bed stop >> Change gears >> Machine feet About the machine: Offered is a Weiler Matador VS-2 in very good condition. The machine is, of course, fully functional. All slides move smoothly and evenly. Even at high speeds, the Weiler runs quietly. The original location of the Weiler was a training workshop. The machine is equipped with a wide range of accessories. Take the opportunity to inspect this machine on-site while it is powered up and to convince yourself of its very good condition.

Condition: excellent (used), Year of construction: 1988, functionality: fully functional, Weiler Matador VS-2 lathe with lead screw and tailstock, featuring a 3-axis digital display from Elesta, from a training workshop!! Technical data: >> Machine no. 88-8115, year of manufacture 1988 >> Center height 140 mm >> Center distance 500 mm >> Speed: 15 – 3550 RPM >> Spindle bore 36 mm >> Short taper spindle head DIN 55022-5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.012 to 0.9 mm/rev >> Possible threads: metric, inch, module, and diametral pitch Ndedsy Tmkvspfx Afujb >> Metric thread pitches from 0.25 to 12 mm >> Brake motor >> Weight approx. 700 kg >> Length 1.4 m, height 1.2 m, depth 0.55 m Accessories and equipment: >> 3-axis digital display Elesta >> Quick-change tool post, internal and external collets (see picture) >> 1 three-jaw chuck, 1 set of jaws >> Mulifix size A with 3 steel holders >> Spindle guard >> 1 bed stop >> Change gears >> Follow rest >> Machine feet About the machine: A Weiler Matador VS-2 in very good condition is offered for sale. The machine is fully functional. The slides all move smoothly and evenly. Even at high speeds, the Weiler runs smoothly. The original location of the Weiler was a training workshop. The machine is equipped with a wide range of accessories. Take the opportunity to inspect this machine on-site while it is powered up and to convince yourself of its very good condition.

Condition: new, Year of construction: 2025, x-travel 580 mm y-travel 200 mm z-travel 340 mm speeds 115 - 1750 U/min table surface area 1000 x 240 mm tool taper ISO 40 total power requirement 4,5 kW weight of the machine ca. 820 kg dimensions of the machine ca. 1290 x 1090 x 2170 mm Universal precision drilling and milling machine for horizontal and vertical milling work with digital 3-axis position display DPA 31 Plus Description: - Heavy, solid design made of high-quality, vibration-absorbing gray cast iron - Oil bath gear with ground, hardened gear wheels - Coolant system - Halogen machine lamp with bundled beam - Solid and large cross table, precisely surface-machined with T-slots and adjustable wedge strips - Milling head can be tilted ± 45° - Right/left rotation - X-axis moves either with the handwheel or via the table feed device - Automatic limit switch on the X-axis - Height-adjustable protective screen with microswitch, against flying chips and parts, for the greatest possible protection of the user Scope of delivery: - Gear rim drill chuck 1 - 16 mm / B 18 - Arbor drill chuck ISO40 / B18 - Horizontal milling spindle with counter bearing, disc milling cutter holder Ø22 mm, Ø27 mm - Adapter ISO 40/MK3 Ndodpfx Afetv Riasusb - Adapter ISO 40/MK2 - Vertical and horizontal drawbar - T-slot nuts - Drifter - Operating tool

Condition: excellent (used), Year of construction: 1992, functionality: fully functional, Weiler Matador VS-2 Lead and Feed Screw Lathe with 3-Axis Digital Readout by K&C—NEW in Special Light Grey Paintwork!!! Technical Data: Nedjyylq Ujpfx Afuodb >> Machine No. 92-027, Year of manufacture: 1992 >> Centre height: 140 mm >> Distance between centres: 500 mm >> Spindle speeds: 15 – 3550 rpm >> Spindle bore: 36 mm >> Short Taper Spindle Nose DIN 55022-5 with bayonet lock >> Tailstock taper: MT 3 >> Feed rates: 0.012 to 0.9 mm/rev >> Thread cutting: Metric, Inch, Module, and Diametral Pitch >> Metric thread pitches: 0.25 to 12 mm >> Weight: approx. 700 kg >> Length: 1.4 m, Height: 1.2 m, Depth: 0.55 m Accessories and Equipment: >> 3-axis digital readout by K&C, brand new, 12-month manufacturer’s warranty with operating manual Functions: mm/inch switching, coordinate selection ABS/INC, value halving, reference mark, tool programming for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 piece 3-jaw chuck with 1 set of jaws >> 1 piece 4-jaw chuck with 1 set of jaws >> Electronic spindle protection >> Multifix size A with 2 tool holders >> Motor brake >> Bed stop About the machine: Offered here is a Weiler Matador VS-2 in very good condition. The machine is, of course, fully functional and has been freshly repainted in light grey. A very attractive machine. The 3-axis digital readout by K&C has been retrofitted. All measuring scales are new and fitted with protective covers to prevent contamination. The carriage movement is smooth and even throughout. Take the opportunity to view this machine under power on site and convince yourself of its condition.