Single-Column Eccentric Press

Weingarten ARP 100

Year of construction: 1985, condition: ready for operation (used), Press force: 100t, stroke rate: 60/min, ram stroke: 8mm-137mm, ram adjustment: 80mm, throat depth: 375mm, table dimensions X/Y/Z: 800mm/630mm, machine dimensions X/Y/Z: approx. 1500mm/2400mm/3500mm, weight: approx. 8800kg. An on-site inspection is possible. Djdsyu T Dqjpfx Anwsut

Condition: excellent (used), Year of construction: 2003, working width: 215 mm, welding power (max.): 750 kVA, Complete Mesh welding/Lattice girder factory Factory consists : - Mesh welding line SCHLATTER PG 24 , Semi- automatic , Year - 2002 - Lattice Girder Line SMEI , Full automatic , Year - 2003 - Straightening and cutting machines 1x Wafios R4 2 x VITARI NR16 1X VITARI NR10 - Cold drawing line SMEI , Input wire max.10mm, Speed - 4m/sec. - But welding achine SMEI - Wire sharpener SMEI Duodpfxoqy Ek Ae Anwot

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Dsdpfou Rwa Iox Anweut Weight 8.3 tons Good condition

Condition: used, Year of construction: 1983, pressure 100 t throat 375 mm stroke 20-125 mm no. of strokes 60 Hub/min ram - range of adjustment 80 mm table surface area 920x660 mm ram surface 700x450 mm hole in the table Ø90 mm Dodpfx Ajxh Swhsnweut tool hole in ram Ø50 mm weight of the machine ca. 8 t dimensions of the machine ca. 2100x1500x3300 m

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Dedpekvnumofx Anwjut Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: as good as new (ex-display), Year of construction: 2025, working width: 1,525 mm, sheet thickness (max.): 100 mm, overall weight: 6,400 kg, The 42 series provides the solution for manufacturers who deliver premium quality products. This top-level quality is achieved by a multi-rotating brush unit with 8 abrasive flap brushes, which perform uniform deburring and produce perfectly rounded metal edges. This is a multidirectional rotary brush machine (RB) for consistent deburring and finishing of flat metal parts. It enables all-round processing in a single pass, giving the workpiece a non-directional surface finish. Equipped with one or more abrasive belt units (W) for pre-deburring and fine grinding. Cup brush unit (TB) for deburring, edge breaking, non-directional finishing, or removal of scale. - Abrasive belt unit (self-calibrating) Dodexw Ih Uopfx Anwsut - Cup brush unit (self-calibrating) - Rotary brush unit with 8 brushes (self-calibrating)

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Duedpfeg U Utvex Anwet Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm 650x450 band speed 15 - 100 m/min table height 844 mm Duodpfed Iipmsx Anwjt dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,9 x 2,87 x 1,3 m PROMOTIONAL PRICE!!! 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off 5. Raise the frame until it is just above the material 6. Vice opens

Year of construction: 1965, condition: used, pressure 150 t throat 550 mm stroke 10 - 140 mm table surface area 1180 x 980 mm no. of strokes 40 Hub/min dayligth 500 mm ram surface 1040 x 800 mm ram adjustment 70 - 150 mm tool shank hole (depth x diameter) 435 x 55 mm required power 15 kW weight of the machine ca. 12 t dimensions of the machine ca. 3 x 1,7 x 3 m - with additional brake - slide weight compensation - motorized slide adjustment - central grease lubrication (manual) Dodpfxjcubato Anwjut - table mounting plate - safe for manual inlay work

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz Dodpfx Anohlnzkswsut - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.