Eccentric press

ZTS Kosice LE-250C

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Hsdpfx Aokvnumelwel Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, Hjdpfx Alsg U Utvowol by means of lateral guide rods. The passage width is continuously adjustable.

Condition: new, table width 3000 mm table length 1500 mm burner heads 1 Control CNC feed 20.000 mm/min total power requirement 15 kVA dimensions of the machine ca. 4,5 x 2,5 m * Heavy machine bed with precision guides for quiet movement machine * A ball bearing cross carriage for height adjustment with 400mm vertical Hub * Thermal separation of the drive and cutting areas ensures the highest precision * Automatic height finding and torch height control during cutting * Torch holder with collision protection and automatic shutdown in the event of a collision * Installation or implementation of the machine using the plug & play method with a forklift, Ant or crane possible * 3-sided accessibility to cutting area through boom design SATOTEC suction table: The SATOTEC table system is characterized by a stable table construction max. cutting thickness of 150 mm. For cutting a workpiece thickness of 150 mm, oxyfuel cutting technology is required. Hedpspm U U Nefx Alwol The workpiece support frame has interchangeable ones placed at a 45° angle and 3 mm thick flat iron slats. The distance between the slats is 50 mm. Power source Kjellberg Q1500: * Precise plasma cutting of all electrically conductive materials from 0.5 to 60 mm both dry and under water * Recommended cutting range from 0.5 to 40 mm * Maximum piercing thickness 30 mm, increase possible with ProPierce Technology * Marking, notching and punching, including coated metallic materials * Inverter power source with digitally controlled, fully electronic process flow * Integrated cooling with partially automated filling and emptying Gas control: Fully automatically controlled, processor-controlled plasma all-gas console Q- Gas for cutting all metals Lantek Expert Cut Inside: CAD/CAM module integrated in the machine control Extraction TEKA EcoCube 5.5 kW Medium to be filtered: dry, fat-free or oil-free dust/smoke Filter area: 100 m² (4 cartridges of 25 m²) Filter cartridge: BIA M, Type Nano Degree of separation: 99% (according to BGIA test certificate) Filter control: automatic filter cleaning, PLC Fan performance: 4500 m³/h Motor power: 5.5 kW Connection voltage: 400V/50 Hz or 480V 60Hz. Current consumption: 11.5 A Current type: 3Ph+N+PE Fan structure: on the system, including silencer duct bend, right side Motor control: frequency converter Noise level: 75dB(A) + max 10 dB(A) with cleaning pulse Intake port: NW 250 mm via intake duct, left side Exhaust: via silencer duct bend Dimensions (W x D): approx. 800 x 800 mm System color: - Fan housing: Light gray - Cartridge housing: RAL 5007 brilliant blue Special equipment: - Locking hooks and toggle locks - Compressed air connection and condensate drain each mounted with one Bulkhead fitting - Compressed air connection with hose nozzle d=8mm - Provide the system with grounding bolts - Cable in UL version - EATON frequency converter on the left in the attached control cabinet

Condition: used, Year of construction: 1983, Technical details: Hsdsu Nfvuepfx Alwel Pressure: 160 t throat: 360 mm max. ram stroke: 500 mm distance table/ram: 800 mm clamping plate on table: 1250x630x100 mm passage opening in table: 4x Ø 62mm mm ram speed - forward: 200 mm/s ram speed - reverse: 125 mm/S ram surface area: 450 x 850 mm mortise hole in ram: Ø 49 mm height over floor: 810 mm total power requirement: 17 kW weight of the machine ca.: 7200 kg dimension machine xH: 2,1 x 1,4 x 3,4 m manual counter *

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Hsdpohlnzkjfx Alwsl Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: used, Year of construction: 2003, pressure 250 t stroke 20 - 190 mm no. of strokes 25 - 140 /min throat 460 mm passage to the back 590 mm dayligth 690 mm table surface area 1500 x 880 mm hole in the table 950 x 250 mm table height over floor 900 mm ram surface 870 x 725 mm ram adjustment 120 mm power requirement 30,0 kW Weight 32,0 t dimensions of the machine ca. 2,34 x 2,38 x 3,99 m x m x m permitted for manual loading and automatic mode according to the CE-norm with infinitely variable drive, light guard (make Sick), hydraulic clutch/brake combination, hydraulic overload protection in ram, automatic stroke adjustment, motoric ram adjustment, pneumatic counterbalance in ram, fix table, drawing cushion in table (20 t), motoric centralized lubrication, operator's console with two-hand operation Hodsvuun Tepfx Alwel Width between the tie rods in front 940 mm Side passage 900 mm

Condition: reconditioned (used), Robot welding machine with 2 m two-station turner. Offered is a robot welding machine from the company Yaskawa Motoman incl. RM2-250 turner Safety engineering Robot UP20 XRC nozzle cleaner etc. The system can be set up and put into operation by us. There is also the possibility of instruction and training. Hsdpfx Aljd Tfb Newjl The plant is prepared according to customer requirements We are YASKAWA system partner and offer you the complete service for your Motoman robot and your systems.

Condition: new, functionality: fully functional, Comparable with Durma, Baykal, Ermaksan, etc. Hodpfx Aljuf Nr Aowsl Bending length 3020 mm Pressing force 320 t (also available in many other configurations!) Approach speed 140 mm/s Bending speed max. 10 mm/s Return speed 130 mm/s Y-axis stroke 400 mm Open height 650 mm Throat depth 450 mm Clear gap between frames 2555 mm Machine length 3785 mm Machine width 2290 mm Width without support arms 1740 mm Overall height 3100 mm Table height 920 mm Motor power 22 kW Oil tank capacity 300 l Machine weight 14,450 kg (Specifications may vary depending on equipment) Standard equipment: 3 CNC axes (Y1, Y2, X) Press beam double-guided, stable and precise Robust double-guided backgauge Backgauge fingers double-guided on linear rails Movable front arms with height adjustment Side and rear safety guards 60mm lower die adapter rail Manual upper tool clamping system (Promecam system) Foot switch with emergency stop 380 V, 50-60 Hz, 3 phase LED lighting Additional equipment: Delem DA 66t CNC control R-axis (backgauge) CNC controlled CNC-controlled crowning Fiessler Akas 2M laser safety device 2 additional backgauge fingers (total 4) 1 set of top and bottom tooling - Further processing lengths and capacities available upon request with appropriate accessories! -

Condition: used, Year of construction: 2000, table length 1160 mm table width 710 mm daylight 650 mm Control WENZEL ME 5007 total power requirement kW weight of the machine ca. 800 kg dimensions of the machine ca. m Hodot Hw S Ijpfx Alwjl 3-D-coordinate measuring machine with METROLOG II-Software

Condition: used, Year of construction: 1987, pressure / t stroke / mm table-size / mm weight of the machine ca. 65000 kg Make: Shepherd Type: SVRM 4-roller bending machine: Year of construction: 1986 Working width: 3000cm Smallest pipe diameter with 600 mm roller: Ø 720 mm Hsdpfx Alsuddcaswol Smallest tube diameter with 360 mm roller: Ø 460 mm Sheet thickness up to (depending on the material): 50 mm Material SA- 738 B Working width: 2500 mm Material SA- 738 B Material thickness: 35 mm conical bending: Except for the top roller, all rollers can be moved in an inclined position for conical bending. The roller positions can be read on display instruments. For semi-automatic or fully automatic operation of the machine, the bearing jewels of the rollers are equipped with scale bars and slide cams for limit switch actuation. This allows the rollers to return to the same set position over and over again, giving a very high level of uniformity in the shot wefts being bent.