Used panel saws with a cutting length from 3000 to 3999mm for sale (63)

Condition: like new (used), Year of construction: 2003, I sell the panel beam saw SCM Sigma 85KC. Year 2003. Cutting size 3300x3200mm. Cutting height 85mm. Main motor 7,5kW Scoring motor 1,1kW Total power 10kW Total area covered W.5400mm x D.7000mm 5 pcs. gripper with pneumatic regulation Side alignment top roller with pneumatic stroke. WinCut optimising software included. Nwodpfszvhy Isx Aiujk Very good condition. Available immediately.

Condition: used, Year of construction: 2001, machine/vehicle number: 0-34-07-5949, functionality: fully functional, input voltage: 24 V, input current: 48 A, input frequency: 50 Hz, cutting height (max.): 320 mm, cutting width (max.): 60 mm, We offer this used HOMAG Optimat chf 41 circular table saw, year of construction 2002. Manufacturer: HOMAG Model: Optimat chf 41 Construction year: 2002 year Condition: used Category ID: 2094 Type ID: 1612 Machine type: circular table saw Njdpfozq Hwhex Aiuswk If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: used, Year of construction: 2024, machine/vehicle number: 0-341-87-0182, operating hours: 1,354 h, total length: 6,080 mm, total width: 4,950 mm, total height: 1,940 mm, Used panel saw, available for inspection while in operation. ▪️Labeling software ▪️Manual label printer ▪️Stress-free cutting/ripping program (cutting cycles, stress elimination, reduced waste) ▪️tapio ready Nsdpfjzu Nytjx Aiuowk Transportation is the responsibility of the buyer.

Condition: used, Year of construction: 2023, Cutting area: 5600x5600 mm 1x Gabbiani G 3 130 (56) - High-performance panel dividing saw 1x Compact label printer 1x "eye-M EVO" control console 1x Human-Machine Interface (HMI) software MAESTRO ACTIVE 1x Maestro pattern 1x High-performance, fixed air cushion table with guide, 2500x600 mm, with infeed rollers 3x High-performance, mobile air cushion table - 2500x600 mm, with infeed rollers 1x Double, lateral, automatic aligner with motor drive 1x Foot switch for START/STOP of the working cycle 1x Setup for grooving with height adjustment of the saw blade via the control system 1x "Autosetting" device on the saw carriage for cutting length/width 1x Main saw blade motor 25 HP (18 kW) 50 Hz with star-delta starter 1x Quick clamping of the saw blades with mechanical flanges "AKE" 1x Selective collet chuck (area 0 - 1600 mm) 3x Additional double collet chuck 4x Additional collet chuck with single finger 1x Compact office label printer 1x Cut editor 1x Maestro optiwise - Advanced - No. 1 license 1x Maestro connect: Service agreement for 1 year (including "plug&play" gateway kit) Nwedpfxexlvktj Aiuek 1x Base 1x MACHINE LANGUAGE: German 1x PC LANGUAGE: German 1x SPEC01 Special version 01 1x European safety regulations (CE marking) including 123 hours of on-site commissioning (within Germany) (daily working hours are 8 hours including travel time). including 1 day of online training MAESTRO OPTIWISE PRO (as needed) including MAESTRO CONNECT 1 year including MAESTRO PATTERN IMPORT (255€ free)!!! FULL MANUFACTURER'S WARRANTY IN THE FIRST YEAR !!! Storage location:

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, cutting height (max.): 50 mm, cutting width (max.): 3,300 mm, saw blade diameter: 300 mm, Equipment: documentation/manual, type plate available, For sale: SIGMA PRIMA 50 panel saw (2016) with label printer – precision, power, and reliability in one! Nwedpjzqc E Iefx Aiuok We offer a professional Sigma Prima 50 panel saw from 2016 – an ideal solution for carpentry workshops, furniture factories, and companies involved in the production of wood-based panel components. Why choose it? 1. Highest level of cutting precision – a stable structure and high-quality guides guarantee perfectly straight and repeatable cuts. 2. Powerful and efficient motor – easily handles MDF, particleboard, laminate, or solid wood. 3. Large panel table – comfortable processing even of large-format panels. 4. Scoring saw – perfect edge finishing without chipping. 5. Year of manufacture 2016 – modern design, proven and ready for work. 6. Connected label printer, ensuring that each component is accurately labeled, preventing errors during assembly. Ideal for: 1. Production of custom-made furniture 2. Serial processing of panels 3. Companies producing prefabricated houses 4. Precision carpentry work 5. Businesses that value quality and efficiency The machine is in good working order, robust, durable, and designed for intensive use. It is an investment that will quickly pay for itself thanks to increased efficiency and accuracy. Contact us for more information, photos, or to arrange a viewing. Don't miss this opportunity – a professional panel saw in very good condition is a guarantee of quality for years to come! We purchased a new model, so this one is being sold. Price: 96,500 PLN net Tel. 666-609-957

Condition: used, Year of construction: 2022, - Work surface: 3800 x 2200 mm with rear lifting table - Maximum cutting length: 3800 mm - Saw blade overhang: 108 mm - Maximum gripper opening: 100 mm - Minimum panel size: 1830 x 915 mm - Maximum panel size: 3660 x 2200 mm - Maximum stack height: 630 mm - Minimum thickness on the lifting table: 10 mm - Maximum lifting table stroke: 985 mm - Load capacity of the lifting table: 5 t Panel dividing saw Manufacturer: Biesse Type: Selco WNT 630 Year of manufacture: 2022 Technical data - Work surface: 3800 x 2200 mm with rear lifting table - Maximum cutting length: 3800 mm Nsdpozuyl Tefx Aiujwk - Saw blade overhang: 108 mm - Maximum gripper opening: 100 mm - Minimum panel size: 1830 x 915 mm - Maximum panel size: 3660 x 2200 mm - Maximum stack height: 630 mm - Minimum thickness on the lifting table: 10 mm - Maximum lifting table stroke: 985 mm - Load capacity of the lifting table: 5 t The machine is almost new and has only been used for a few months. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: ready for operation (used), Year of construction: 2007, Main motor (kW): 27 Njdpjzgwpgefx Aiujwk Infeed device Saw length (mm): 3300 Saw width (mm): 3300 Panel thickness (mm): 40 All specifications are manufacturer’s data.

Condition: used, Year of construction: 2006, with automatic lifting table feeding system with 4 precision spindles, ensuring the stack is always held evenly at the correct level. Equipped with 4 powered roller groups. Lifting table dimensions: 6000 x 2200 mm. Feeding side: left (from the operator's perspective). Max. stack height: 450 mm. Lifting table height (bottom): to be defined. Speed for lifting and lowering: 0.7 m/min. Lifting table drive: 3 kW. Powered roller group: 4. STANDARD CONFIGURATION. Usable cutting length: 6000 mm. Lifting table feeding: Yes. Working height: 950 mm. Saw blade overhang: 100 mm. Clamping device opening: 117 mm. Machine control: G Drive RT. Number of clamping devices movable in X: 1. Number of clamping devices movable in X and Y: 1. Number of fixed clamping devices: 1. Min. material thickness (with side alignment): 10 mm. Min. material thickness (with lifting table feeding): 10 mm. Min. panel dimension (with lifting table feeding): 2400x1200 mm. Max. panel dimension (with lifting table feeding): 5500x2070 mm. Max. panel dimension (without lifting table feeding): 5800x2010 mm. Safety device according to CE: included. Supply voltage: 400 V / 50 Hz. MACHINE CONFIGURATION. Machine bed: The machine bed structure made of steel is welded using arc welding and then milled and finished on CNC machines. The rigid structure of the machine bed guarantees both high cutting quality with high cutting speed, as well as the enormous durability of the entire machine. Saw blade overhang: 100 mm. Power of main saw motor: 7.5 kW. Power of scoring saw motor: 2.2 kW. Diameter of main saw blade: 400 mm. Diameter of scoring saw blade: 215 mm. Feed rate of saw carriage: Forward: 1-170 m/min. Return: 170 m/min. Motorization of saw carriage feed: Servo drive. Diameter of dust extraction port (bottom, 1x): 200 mm. Diameter of dust extraction port (top, 2x): 115 mm. Thanks to the rigid machine bed construction, the masses are distributed in the best possible way, which prevents twisting and thus guarantees an absolutely vertical run of the saw blade. Machine table made of steel with individual, removable support elements made of high-quality, durable material. The saw carriage runs on two round guides, which are mounted horizontally on one level. Large prism rollers (diameter 86 mm), with spring-loaded counter rollers, ensure smooth linear feed, as well as very low contact pressure and enables virtually wear-free operation of the saw carriage. The weight and forces acting on the saw carriage are evenly distributed on the two guides (50/50) and on each individual prism roller. The saw carriage runs absolutely without lubricant on the guides. The two guides are located away from the cutting line, outside the direct dust area. The diameter of the guide rods is 40 mm, making them the largest and most stable guides used in this sector. Pneumatic quick clamping system; for quick and convenient tool changes. This system is extremely reliable in operation, as it is mechanically clamped via a flange with a bayonet lock and spring force and unlocked via a pneumatic quick coupling. The flange must be rotated by approx. 10° in order to remove it. Due to excellent accessibility and the fact that the operator does not need any other tools, the tool change is very easy and can be carried out in seconds. The scoring saw adjustment is made from the outside. Nwsdpfx Aiozn N Ikeuek

Condition: ready for operation (used), Year of construction: 2005, machine/vehicle number: GA1/002357, functionality: fully functional, input voltage: 400 V, input current: 51 A, input frequency: 50 Hz, overall weight: 6,000 kg, year of last overhaul: 2025, Equipment: CE marking, documentation/manual, Panel Saw Gabbiani Galaxy T 108 PR – 2005 Manufacturer: SCM Group Njdpfxsy R Svre Aiuewk Weight: 5,000 kg Condition: fully operational Performed maintenance: Complete operational check Inspection of mechanical systems Inspection of electrical system General maintenance Professional machine suitable for industrial production. Available for testing.

Condition: excellent (used), Year of construction: 2004, functionality: unexamined, Used sheet metal cutting system Model GABBIANI Galaxy 85 K Year of manufacture 2004 Good condition, inspection possible at our location in the Netherlands. Njdpjzty Husfx Aiujwk Availability: approximately end of October 2026 3200 x 3200 mm WinCut software 3 air cushion tables Sale in current condition, ex works from our location in the Netherlands.

Condition: used, Year of construction: 2006, functionality: fully functional, Machine identification Model: SCM Sigma Plus 125 P 45 Type: heavy-duty panel saw with lifting platform Manufacturer: SCM Group S.p.A., Italy Serial number: AE/028708 Year of manufacture: 2006 (used machine) Condition: used industrial panel saw Nwsdpfxey Iwy Dj Aiujk Main equipment / configuration Fixed, phenolic-coated front air cushion table with stop Three movable, phenolic-coated air cushion tables Pneumatic automatic alignment device Quick saw blade change system Independent main saw blade lifting THK precision linear guides Four additional clamps in the right-angle alignment zone Optimized saw blade extension PC operator interface in English

Condition: used, Year of construction: 2009, machine/vehicle number: 731, functionality: fully functional, input voltage: 400 V, input current: 35 A, input frequency: 50 Hz, cutting height (max.): 100 mm, cutting width (max.): 3,800 mm, saw blade diameter: 380 mm, saw blade bore: 80 mm, rotational speed (max.): 4,800 rpm, rotational speed (min.): 2,800 rpm, total height: 1,650 mm, overall weight: 4,500 kg, travel distance X-axis: 3,800 mm, cutting length (max.): 3,800 mm, workpiece weight (max.): 80 kg, air pressure: 6 bar, compressed air connection: 6 bar, cutting height with scoring (max.): 100 mm, extraction nozzle diameter: 120 mm, feed length X-axis: 3,800 mm, feed rate X-axis: 70 m/min, main saw diameter: 380 mm, Equipment: scorer, The saw is regularly serviced and in perfect working order. It is in daily operation on a single shift. Sale due to transition to a newer production system. Still functional, it can be seen in operation until October 10, 2025. Also supplied with a set of saw blades and a pre-cutter. Option to purchase a vacuum board lifter, which can be seen in the video. Njdpfx Aisxf Im Tjuowk

Condition: used, Year of construction: 2005, - Saw motor: up to 19 kW at 2930 rpm, 50 Hz - Scoring motor: 1.5 kW at 2830 rpm, 50 Hz Panel dividing saw Manufacturer: Schelling Type: FM-H 430 Year of manufacture: 2005 Technical data Infeed speed: Forward: 0-25 m/min Reverse: 80 m/min Saw feed speed: Forward: up to 120 m/min Reverse: 120 m/min Saw motor: up to 19 kW at 2930 rpm, 50 Hz Scoring motor: 1.5 kW at 2830 rpm, 50 Hz Clamping opening: 113 mm Cutting straightness: +/- 0.1 mm over a cutting length of 3 m Dimensional accuracy: +/- 0.2 mm length, +/- 0.2 mm width, +/- 0.3 mm diagonal Main saw blade: Diameter: 450 mm Inner bore diameter: 30 mm Saw blade thickness: 4.4 mm Number of teeth: 72 Scoring blade: Diameter: 200 mm Inner bore diameter: 20 mm Nwsdpozuy Diefx Aiujk Saw blade thickness: 4.2 / 3.5 mm Number of teeth: 36 Edge scoring blade: Diameter: 220 mm Inner bore diameter: 20 mm Saw blade thickness: 4 / 4.8 mm Number of teeth: 2 x 24 Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: good (used), Year of construction: 2018, functionality: fully functional, power: 7.5 kW (10.20 HP), input voltage: 400 V, input frequency: 50 Hz, saw blade diameter: 380 mm, Equipment: documentation/manual, Number of clamps: 6 Cutting length: 3800 mm Max. saw blade overhang: 90 mm Air tables: 4x Features include “post-forming” for a single panel or a stack of laminated panels, a linear motor for moving the saw carriage without any friction or mechanical components, a speed exceeding 200 m/min, and an acceleration of almost “1g”, among many others. PRISMA EVO is a cutting center without a motor on the saw carriage (patented), and thanks to this extraordinary innovation, all causes of vibration are definitively eliminated, which improves the quality of the cut surface and ensures a longer blade life. PRISMA EVO uses linear guides with ball bearings for all sliding movements of the saw carriage, the pressure beam, and the side pressure device as standard. The feeder of this model is automatic, electronically controlled, and equipped with a brushless motor. The side aligner is “permanently engaged,” which guarantees a faster cross-cutting cycle for a single strip. The side aligner slides on a linear guide, ensuring smooth and clean movements, and is wear-resistant and virtually maintenance-free. Njdpfx Asy S Rhceiuswk

Condition: ready for operation (used), Year of construction: 1987, machine/vehicle number: 402, functionality: fully functional, cutting height (max.): 70 mm, cutting width (max.): 3,200 mm, saw blade diameter: 300 mm, cutting length (max.): 3,200 mm, cutting height with scoring (max.): 70 mm, Equipment: scorer, Cutting length: 3200 mm Cutting width: 3200 mm Width stop: Gear motor adjustment Main saw unit: saw blade Ø 300, Ø 30, Z=60, SH 70 Scoring unit: yes - saw blade Ø 125, Ø 20, Z=24 Softforming unit: no Side pressure unit: yes - Version: FR 50/100 Residual cutting device: yes - Pressure beam recess Veneer cutting device: yes Trimming device: yes - Spacing: 145/525/1790 Support table front: 400 x 1400 mm - 2 pieces Rear support table: 240 x 2960 mm - 1 piece Support bars rear: 40 x 2960 mm - 5 pieces Angled table: 480 x 1400 mm left Angle ruler: with pull-out Collets: 4 pieces - floating - distance 70/400/1600/2800 Stop jaw: 2 pieces - rigid - distance 1000/2200 additional foot at the rear : no - 3 feet safety guard: yes foot switch : no Njdpfjvi H Disx Aiuewk Machine cuts from: left to right unit can emerge in any area: no automatic lowering with saw overtravel: no 3-step cutting height adjustment: no Main circular saw: 7.5 kW, 380 V, 2870 rpm, 50 Hz Scoring saw: 1.1 kW, 380 V, 2800 rpm, 50 Hz Width stop adjustment motor with torque compensation: fine input motor: 0.12 kW, 380 V, 1380 /min, main motor: 0.35 kW, 380 V, 1350n.

Condition: used, Year of construction: 2001, functionality: fully functional, power: 13.5 kW (18.35 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, cutting height (max.): 125 mm, cutting width (max.): 3,200 mm, saw blade diameter: 450 mm, Equipment: CE marking, scorer, We are offering this used Holzma HPP 11/32 panel saw, year of manufacture 2001. Manufacturer: Holzma Model: HPP 11/32 Year of manufacture: 2001 The machine is in perfect working condition. Complies with CE safety standards. Automatic panel saw for chip-free and precise cutting of coated and uncoated boards made from wood-based materials and those that can be processed like wood-based panels. Rear machine table equipped with the appropriate number of combi-profile rails with rollers for easy and gentle handling of panels. Machine table features extensive, abrasion-resistant table supports, which are recessed at the clamping jaw positions. This ensures lasting table stability and consistent cutting quality. Saw blade feed direction: from left to right against the square fence. Technical specifications: Main saw motor: 13.5 kW Scoring saw motor: 2.2 kW Max. clamping jaw opening: 130 mm Saw blade diameter: 450 mm Saw blade projection: 125 mm Saw carriage feed rate, forward: 5–100 m/min Return feed rate: constant 100 m/min Program carriage feed speed, forward/return: max. 80 m/min Compressed air: 6 bar Operating voltage: 400 V / 50 Hz Minimum extraction speed at extraction nozzle: approx. 28 m/sec Chip extraction connection: 1 x 200 mm Pressure beam extraction connection: 1 x 160 mm Minimum operating temperature: +5°C Maximum operating temperature: +35°C Cutting length: 3,200 mm Cutting width: 3,200 mm Dismantling and collection to be organized by buyer. Location for collection: A-8265 Kroisbach an der Feistritz Nedpfx Aeyxqigeiuowk If you have any questions or require further information, please feel free to send us a message or call us.

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, Cutting length: 4300 mm Cutting depth: 4300 mm 7.5 kW main blade unit Scoring blade unit 1 fixed front table with air cushion 3 mobile front tables with air cushion Nwedeznz Uispfx Aiujk Pushing carriage with approx. 7 clamps WinCut software Foot pedal for cycle start and stop Safety guards Weight approx. 3277 kg. Available starting September 2026.

Condition: ready for operation (used), Year of construction: 2006, operating hours: 80,773 h, total height: 2,400 mm, cutting length (max.): 3,200 mm, Panel saw manufactured in 2006. This MAYER AL160 features a saw blade diameter of 650 mm and a maximum cutting width of 3200 mm x 3200 mm. It has a main saw motor power of 35 kW and offers variable forward speeds for both the saw aggregate and infeed. If you are looking to get high-quality panel cutting capabilities, consider the MAYER AL160 machine we have for sale. Contact us for further details. Nsdezug Arjpfx Aiujwk - Main Saw Motor Power: 35 kW- Saw Blade Diameter: 650 mm- Package Clamps / Collets: 210 mm maximum- Saw Aggregate Forward Speed: 0.2 - 60 m/min- Saw Aggregate Return Speed: 60 m/min- Infeed Forward Speed: 10 m/min- Infeed Return Speed: 20 m/min- Extraction Connections: 1 x 140 mm, 1 x 160 mm- Working Height: 1100 mm- Installation Dimensions: approx. 6280 mm (W) x 6855 mm (L)- Cutting Width/Length: 3200 mm x 3200 mm- Compressed Air Volume: 720 Nl/min- Operating Pressure: min. 5 bar, max. 6 bar- Component Condition Notes: Requires repair/adjustment on 3 package clamps, dust protection curtain, and cutting lips at the saw gap

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, HI-TRONIC unit with vertical stroke and blade speed adjustment, with a power of 25 HP (18 kW), making it also suitable for cutting plastic materials. Cutting length: 3200 mm Nedezdqk Sjpfx Aiuewk Cutting width / Cutting depth: 3200 mm Cutting height: 130 mm Main blade unit Scoring blade unit 1 fixed front table with air cushion and guide 2 movable front tables with air cushion Pushing carriage with 11 clamps Console with integrated "eye-M" PC Software: Maestro Cut Hardware key for Maestro Pattern + Easy Import Presser, clamps, and aligning device with differentiated pressures controlled by the system START/STOP foot pedal Approximate weight: 4150 kg. Cutting optimization software included Available from August 28, 2026

Condition: excellent (used), Year of construction: 1999, cutting length 3.200 mm cutting width 3.200 mm cutting hight 65 mm saw blade DM max. 300 mm saw blade motor: 5,5 kW scoring unit DM max. 160 mm motor scoring unit 1,5 kW front support tables 3 Stk. 1 x 2500 x 500 & 2 x 1500 x 500 mm cutting optimisation program no. of grippers 8 pcs saw blade hight adjustment on THK guides pressure beam with openings side pusher (alignment) saw blade quick change system suction DM1 x 120 & 1 x 150 mm space requirement L x B 5700 x 6000 mm weight approx. 2500 kg INVERTER NEW Nwodpfohvan Isx Aiujk Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: like new (used), Year of construction: 2020, functionality: limited functionality, operating hours: 50 h, power: 50 kW (67.98 HP), input voltage: 380 V, input current: 80 A, input frequency: 60 Hz, type of input current: three-phase, cutting height (max.): 72 mm, saw blade diameter: 380 mm, height adjustment type: pneumatic, actuation type: electric, total length: 7,500 mm, total width: 6,000 mm, total height: 1,900 mm, overall weight: 5,000 kg, table height: 1,000 mm, Equipment: CE marking, documentation/manual, saw blade guard, scorer, AES Alpha Heavy Duty Beam Saw 3200 * 3800 mm | Showroom Condition | Less 100 Hours Category: Panel Saw / Beam Saw Condition: Used – Like new showroom machine Description: For sale: AES Alpha heavy duty beam saw. The machine has been used exclusively in a showroom for demonstrations and training. It is in working condition with less than 100 working hours. Equipped with all Yaskawa and Schneider Electric drivers. Technical Data: Cutting width: 3200 mm Bridge depth: 3800 mm Main motor: 15 kW (20 HP) Scoring motor: 2.2 kW (3 HP) Max cutting height: 72 mm Saw carriage speed: 70 m/min Pusher speed: 60 m/min Max blade: 380 mm Max scoring blade: 200 mm 8 clamps AES Alpha Heavy Duty Paneelzaag 3200 mm | Showroomstaat | Minder 100 Werkuren Categorie: Paneelzaag / Opdeelzaag Conditie: Gebruikt – Zo goed als nieuw (Showroom) Beschrijving: Te koop: AES Alpha heavy duty paneelzaagmachine. Deze machine werd uitsluitend gebruikt in een showroomomgeving voor demonstraties en trainingen. De machine verkeert in uitstekende staat en heeft minder dan 100 werkuren. Uitgerust met hoogwaardige aandrijvingen van Yaskawa en Schneider Electric, wat zorgt voor maximale betrouwbaarheid en precisie. Technische specificaties: Snijbreedte: 3200 mm Brugdiepte: 3800 mm Hoofdmotor: 15 kW (20 HP) Voorritsmotor: 2,2 kW (3 HP) Nwodpoyzzguofx Aiuek Maximale zaaghoogte: 72 mm Zaagwagensnelheid: 70 m/min Duwbalk snelheid: 60 m/min Max. zaagdiameter: 380 mm Max. voorritsdiameter: 200 mm 8 klemmen Luchtkussentafel (3 stuks): 1 vast, 2 verplaatsbaar Pneumatische zaagwagen beweging Aandrijvingen: Yaskawa & Schneider Levering: Binnen 10 dagen mogelijk Prijs: Op aanvraag

Condition: excellent (used), Year of construction: 2007, machine/vehicle number: 0-243-02-2974, functionality: fully functional, The equipment was purchased new in 2007 for its current location. The factory ceased operations in 2016, and the equipment has not been used since then. The equipment is available for purchase as-is or fully dismantled and loaded onto a truck. Njdpfx Aiozcn Ndjuowk Do not hesitate to contact for more information.

Condition: like new (used), functionality: fully functional, Panel Dividing System SCHEER FM 16 – DNC 3100 x 3100 As New – Machine No. 33542 The SCHEER FM 16 is a high-performance, electronically controlled panel dividing saw featuring advanced drive technology and an intuitive control interface. The machine has been fully overhauled and newly painted – its condition is virtually as new. Ideal for precise, automated cutting of wood-based panels in continuous industrial operation. Main Technical Data: • Cutting length: 3100 mm • Cutting depth / Blade projection: 80 mm • Saw motor: 7.0 kW • Scoring motor: 1.1 kW (can be switched off) • Feed speed: 2 – 40 m/min (steplessly adjustable) • Return: Rapid traverse, automatic lowering • Operator interface: SCHEERWIN, graphical, document-oriented (64-bit) on Windows 10 • Drive system: Küenle frequency inverter with Stöber synchronous servo drives incl. absolute encoder – for highest positioning accuracy and dynamic control Features & Highlights: • FM 16-3100 longitudinal cutting saw with hardened guides and automatic forward/reverse travel • HP 5021 material feed table with 6 clamping carriages, servo drive & measuring resolution of 0.05 mm • WP angular pressure system, 2400 mm adjustment range, fully automatic • SP 5000 remnant cutting device for offcuts down to min. 5 mm • HP 5024 miter fence table (1800 x 800 mm), steel angle with Pertinax overlay • HP 5025 workpiece support table (1800 x 800 mm), also with Pertinax overlay • Air cushion system in the front tables, including radial fan Saw blades included: • KSB 4005 for main saw (ø 305 mm, Z = 60) • KSB 4006 for scorer (ø 200 mm) Condition & Service: • Condition: Overhauled & as new • Functionality: Fully operational • Warranty: 12 months Reliability in Continuous Operation: This machine is in use worldwide – even under extreme conditions. Whether in the dry climates of Africa or the humid environments of Southeast Asia (e.g., Thailand), the SCHEER FM 16 operates reliably in 3-shift systems – 365 days a year – and stands out for its superior precision, stability, and durability. Warranty: We are so confident in the quality and robustness of our machines that we offer a 7-year warranty on the machine frame and guideways. (Excludes electrical supplier components and wear parts.) Flexibility & Customization: We offer various models and equipment options – to fit every budget. We also realize custom tailored solutions based on your individual requirements. 📞 Contact us for an individual offer or to arrange a viewing appointment. Nwsdpfeunwk Tox Aiusk Machine available from stock. Delivery, commissioning and training optionally available.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, cutting height (max.): 90 mm, cutting width (max.): 3,800 mm, saw blade diameter: 380 mm, overall weight: 4,400 kg, cutting length (max.): 3,800 mm, main saw diameter: 380 mm, Beamsaw SIGMA IMPACT 90 (SCM Group) suitable for furniture panels precize cutting by one or more panels overlapped. Manufacturer: SCM Group Model: Sigma Impact 90 Production year: 2017 Cutting width: 3.800 mm Cutting depth: 3.200 mm Max. cutting height: 90 mm Front tables (air cushion): 1x 2.500x600mm, 3x 2.500x600mm Machine basement with air-cushion. Nedpfex Nc Aysx Aiuswk Max. main blade diameter: 380 mm Scorer diameter: max. 300 mm PUSHER: brushless motor, max. speed 120 m/min ! SAW CARRIAGE: brushless motor, max. speed 150 m/min ! THK linear guides for the saw carriage movement. THK linear guides for the PUSHER movement. Automatic centralized lubrication of THK linear guides. Hi-Tronic kit: - main motor 15 kW (mode S6) - vertical movement of main and scoring blade by price ball-screws - optimized stroke of the main blade - electronic scorer adjustment in 2 axis (vertical, horizontal) - grooving with the main blade (electronic depth adjustment) - postforming cuts - window cut outs (blind cuts) - AKE flange for main and scoring blade Quantity of clamps (grippers): 10 pcs (maximum) Automatic exclusion of the clamp acting on the panels edge (up to 800 mm width). Start/stop pedal. Label printer. Control SW: WINCUT Optimalisation program: OTTIMO PERFECT CUT TOP (1x HW key) Control PC Eye-S: Windows + LCD touch screen 21" Air conditioning device for the electric box. Panel´s dimension automatic measuring. Laser line for the visualisation of the cutting line. Automatic double side aligner - motorized (60-2.200 mm). Machine stat: fully working Possibility to see in actuall production. Availability: cca April 2026

Condition: as good as new (ex-display), Year of construction: 2023, functionality: fully functional, power: 7.35 kW (9.99 HP), input voltage: 400 V, input frequency: 50 Hz, cutting height (max.): 105 mm, cutting width (max.): 1,300 mm, saw blade diameter: 350 mm, rotational speed (max.): 4,000 rpm, total length: 4,300 mm, overall weight: 1,300 kg, cutting length (max.): 3,200 mm, pivoting range: 45 °, The Concept 350 combines the advantages of various saw systems: As flexible as a panel saw, the cutting quality of a pressure beam saw, and as ergonomic as a trimming saw. This is the sawing concept for modern industrial production. The machine is a leasing return. Further technical data: - Motorized rip fence with 4 aluminum stops, which move synchronously - Screen control with 8" touchscreen - Air requirement: 6 bar - Sliding table: 1,000 x 400 mm (extension table) - Outrigger table size: 3,200 mm with 2 digital stop jaws - Extraction connection: 1 x 100 mm, 1 x 120 mm - Feed speed: 0 - 40 m/min Special features: - Programmable saw blade height adjustment - Mitre fence +/- 50° Nodpfxswzuips Aiuowk - Cutting line laser - Additional support table 800 x 200 mm With the new Concept 350, you no longer need a panel saw! The workpiece rests on the machine and is positioned precisely with a pressure beam. The saw unit can be swiveled from 90° to 45°, is guided with precision, and cuts your workpiece at a constant feed speed of 0–40 m/min, ensuring the best possible cutting results. The standard crosscut fence enables quick cutting to length and efficient operation, with significantly less space required compared to any sliding table saw! Advantages over a sliding table panel saw: - Significantly less space required - The pressure beam secures the workpiece on the machine and guarantees optimal cutting results - The pressure beam prevents the operator from reaching into the saw blade - Ergonomic operation, as the operator no longer has to push the material through the saw blade - Time saving, as the operator does not need to guide the material during the sawing process Including delivery and installation within postal code areas 71, 72, 73, 77, 78, 79, 86, 87, 88, 89.