Used reinforced steel - bending machines for sale (19)

Condition: new, Year of construction: 2026, rebar bending machine evo 36 400 Volt 50 Hz 3 ph. capacity up to 36 mm at R=65kg/mm2 weight 320 kg with 6 round tooling 50-60-70-80-95-120 mm 1 pc. square bolt foot pedal CE declaration Ijdpfx Ahehiyadjnjba

Condition: good (used), Reinforcing steel bending machine, shaft bending machine, round steel bending machine -Drive: hydraulic -Power: 4 kW -Bending angle: for left/right to adjust the angle -Equipment: adjustable counter-support strips, standard bending tool Ijdpfxeyb R Nde Ahnjba -Dimensions: 930/1640/H890 mm -Weight: 1200 kg

Condition: good (used), Reinforcing steel bending machine, shaft bending machine, round steel bending machine Iedsyb R Akopfx Ahnoba -Drive: hydraulic -Power: 4 kW -Bending angle: for left/right to adjust the angle -Equipment: adjustable counter-support strips, standard bending tool -Dimensions: 930/1640/H890 mm -Weight: 1140 kg

Condition: new, engine 2,8 KW Ibsdpfx Ahey H N Nzonoa weight of the machine ca. 320 kg dimensions of the machine ca. 86 x 90 x 85 cm

Condition: used, Rebar Bending Machine, Reinforcing Steel Bender, Alba DAR 45, Used Machine Manufacturer: Alba (Spain) Type: DAR 45 (Dobladoras Automáticas) Overall dimensions: Width: 1300 mm Depth: 800 mm Height: 830 mm Weight: 555 kg Electrical data: 400 V Iedpfx Aey Rh Rfjhnjba Maximum bending diameter: Ø 45 mm (single bar, for 450 N/mm² steel grade) Bending speed: 2 speed settings (higher speed for smaller diameters)

Condition: used, Rebar Bending Machine, Reinforcing Steel Bender, Peddinghaus Special 32, Used Machine Manufacturer: Peddinghaus Type: Special 32 Overall dimensions: Width: 660 mm Depth: 850 mm Height: 830 mm Weight: 325 kg Electrical data: 400 V; 7 A Bending capacity: max. Ø 32 mm (single bar) Bending speed: approx. 10 rpm Motor power: 2.2 kW Control system: Automatic bending angle adjustment, foot pedal start Isdpfxjy R A Nij Ahnjba

Condition: used, Technical details: bending angle max.: 180 ° working height: 350-550 mm operating voltage: 380 V revolutions per minute: 10-20 U/min number of bars max.: 1-4 mm total power requirement: 1,3/2,1 kW Iedpfxjxu Dxqo Ahneba Weight approx.: 690 kg dimension machine xH: 1,2 x 0,87 x 1,2 m -Two plate speeds -Mode selector switch for automatic mode, jog mode, continuous operation -Four continuously adjustable counterholder bars without accessories! *

Condition: used, Year of construction: 2006, Technical details: bending angle max.: 75 ° working height: 850 mm operating voltage: 380 V Weight approx.: 1,0 t dimension machine xH: 1,9 x 2,6 x 1,0 m transport measurements machine: 2,6 x 1,8 x 1,0 m Single bending and double bending of reinforcing steel possible. Number of bending forms = 2 pieces Bending angle 40°; 60°; 75°. bar size: angle form=Ø 12 - 50mm and double angle=Ø 12 - 35mm Operation via control panel with touch screen bending plate: -Ø 480mm -speed= 7,5 / 15 rpm. -bending pin bore= Ø 48mm (16 pieces) -center pin=Ø 50 x 94mm Counterholder bars: -2piece length=840mm -Displacement per handrail 100mm -13 holes of size Ø 48mm Iodpfxou Ibu Ro Ahnoba Accessories: bending attachments 2x Ø 60mm; 2x Ø 78mm; 1x 96mm; 1x Ø 122mm; 1x Ø 160mm; 1x Ø 200mm 1x pin for plate 8x counterholder div. shapes 1x bending trough *

Condition: used, Technical details: bending angle max.: 0 - 225 ° working height: 850 mm operating voltage: 380 V bending angle max.: 0 - 225 ° number of bars max.: 15 mm diameter max.: 55 mm revolutions per minute: 5 -16 U/min total power requirement: 5,5 kW Weight approx.: 0,7 t dimension machine xH: 1,60 x 1,20 x 1,02 m Reinforcing Steel Bending Machine Perfekt 55 KA, PA, PLA — high-performance production machine. Thanks to the control system with four different bending speeds, the machine operates with exceptional efficiency. The bending angle is continuously adjustable from 0 to 225 degrees for left or right rotation. With its correction potentiometer for material spring-back compensation, the machine is ideal for medium and large-scale series production. Using the PA program control unit, up to eight different bending angles can be continuously pre-programmed from 0 to 225 degrees via rotary knobs. without accessories! Ijdpfx Aox Adbnjhnoba *

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, machine/vehicle number: 200713, total width: 950 mm, total length: 1,050 mm, total height: 890 mm, type of input current: three-phase, input voltage: 400 V, overall weight: 585 kg, oil tank capacity: 13 l, rotational speed (max.): 6 rpm, Electric bending machine P54 Evo Bending machine for concrete reinforcing rebar, studied for high volumes of production. Bending capacity: - 1 rod Ø44 mm (1.73 in) / res. 65 kg/mm² - 1 rod Ø40 mm (1.57 in) / res. 85 kg/mm² Engine 4 kW (5,5 CP), power 400 V (three-phase) Dimensions: cm 105 x 95 x h. 89 Net weight: kg. 585 Operation electric Product handled: concrete reinforcement Displacement: horizontal Bending capacity: Min.: 2 mm; Max.: 44 mm RPM 6Two reversal pins, to be positioned on the circumference of the plate to determine the angle of bending; A set of Allen keys, for ordinary maintenance; An electrical pedal, to facilitate the work to the operator permitting him to keep his hands free and work from all sides of the machine; A set of wheels, for the machine handling; Ibodpfx Ahszgv Hdsnja An industrial plug, that guarantees the electrical connection; Two mushroom button switches, to immediately stop the machine in case of emergency. They are positioned on two opposite sides of the machine;Standardly mounted on all Evo rebar bending machines, long saddles – with max. 10 holes – are indispensable to realize the double bending. Price Euro 3.660 Euro + VAT, negotiable, ExWorks Oradea, Romania. Please make an offer. Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale /

Condition: new, bending diam. - max. 36.0 mm ST cutting thickness max. 36.0 mm ST motor 1450 U/min oil volume 32.0 l motor 380 Volt 50 Hz total power requirement 5.5 kW weight 650 kg range L-W-H 1470 x 1200 x 1020 mm Exhibition machine - NEW (!!) Equipment: - Maximum performance, minimum consumption - hydraulic combination machine for bending and cutting processes * for e.g. structural steel or solid material - Bending mode with 3x different angle settings - manual and automatic mode selectable - simultaneous bending and cutting processes when the machine is in operation - "ECO mode" = hydraulic pump only runs when the foot switch is pressed - freely movable foot switch - operating instructions technical data: Ibjdpfx Ahsxabntjnea - steel 45 kg / mm² .. bending Ø 36.0 mm / cutting Ø 36.0 mm * for 2x pieces - steel 45 kg / mm² .. bending Ø 20.0 mm / cutting Ø 24.0 mm - steel 65 kg / mm² .. bending Ø 32.0 mm / cutting Ø 32.0 mm * for 2 pieces - steel 65 kg / mm² .. bending Ø 18.0 mm / cutting Ø 20.0 mm - steel 85 kg / mm² .. bending Ø 26.0 mm / cutting Ø 28.0 mm * for 2 pieces - steel 85 kg / mm² .. bending Ø 14.0 mm / cutting Ø 18.0 mm * Machine video: ?v=zagTSA81VyA

Condition: new, Year of construction: 2026, Rebar Bender IB 36 Isdpjdibzvjfx Ahneba - solid construction - turning table - manual and automatic mode - Pre selection of bending angle 3 piece - 2 sideholders - with foot pedal for left and right bending Technical Details: bending capacity 500 N/mm² 28 mm Dimensions 800x900x800 mm weight 350 kg motor 3,0 KW bei 400 V 50 Hz 3 phase

Condition: new, Universal bending machine UB-100 Eccentric quick-release clamping device Readable bending angle up to 120 degrees Weight: 35 kg Standard accessories: Infinitely adjustable bending stop Eccentric quick-release clamping device Angle stop Lever and bending dies Material stop Cold bending: - Flat steel 100 x 5 mm - Square steel 16 x 16 mm - Round steel 18 mm - Angle steel 60 x 8 mm Hot bending: - Flat steel 100 x 15 mm - Square steel 30 x 30 mm Ibodpoga T Hvjfx Ahnsa - Round steel 30 mm - Angle steel 100 x 12 mm

Condition: new, Year of construction: 2025, – Capacity 36 mm – Automatic and manual mode – 3 programmable bending movements Ijdpfsydhl Ijx Ahneba – Foot pedal operation – Hardened bending tools – Emergency stop – Documentation – 400V

Year of construction: 1991, condition: reconditioned (used), Mubea / Muhr and Bender BB 032 P200: Ijdpfxoium Euo Ahnoba - rebar bending machine with electr. steering - Saving of bending programs with up to 10 different angle sizes - Memory for up to 200 bending programs Special tools and devices on request. Trade-in of used machines. Europe-wide delivery possible.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, Rebar Bender P74 Evo Year of manufacture: 2023 (like new, only used for testing) Programmable with digital display With modular workbench with rollers, 2 meters With Uniq stirrup tool for 2 materials, 16 mm Serial no. 400V-50Hz, 3-phase basic A/C Ibjdpjy Awzksfx Ahnea Motor: 7.5 kW CE declaration With preset bending angle via plug-in pins 5 rpm Disc diameter: 720 mm Maximum bush diameter: 400 mm Foot switch Dimensions: 160x116x96 cm Weight: 1600 kg Bending capacity at R = 65 kg/mm2, Round: 60 mm At R = 86 kg/mm2 – round steel: 50 mm With bushes, see photos With 1 piece square pin HS-Code: 8462 5900

Condition: new, Year of construction: 2025, MG20B is suitable for bending your steel into the desired shape. Product information: - Voltage: 380 V (optional with 220 V available) - Motor Power: 1,5 kW - Dimensions Machine: 60cm x 45cm x 32cm - Dimensions Machine frame: 57cm x 44cm x 60cm - Ideal for your construction company or also for your construction sites - Easy to carry - In addition to the individual bending process, a bending sequence can also be programmed - Stirrup head for different reinforcing steel Ø are included in the accessories (incl. accessories, see pictures) - Possible in automatic or manual mode - Bending capacities depending on steel strength according to table (see pictures) - Optional available with digital control panel Ijdpfom Sgx Djx Ahneba - Net weight: 95 kg Shipping: Europe-wide (self-collection also possible) If you have any questions, please do not hesitate to contact us!

Year of construction: 2023, operating hours: 0 h, condition: new, HB12X6 (optional 12X3) is suitable for bending your reinforcing steel mesh into the desired shape. Product information: - Motor Power: 7,5 kW (5,5 kW) - Voltage: 380 V - Length: 6400 mm (3400 mm) - Width: 1000 mm - Height: 1090 mm - Hydraulic Oil Tank Capacity: 36 l - 6 m (3 m optional) - 3 stops - Bending angles: 45°-90°-135° - Net weight: 1250 kg (710 kg) Shipping: Europe-wide (self-collection also possible) Ibsdpfx Ajm Tmddjhnea If you have any questions, please do not hesitate to contact us!

Condition: new, Year of construction: 2023, B-Series is suitable for bending your steel into the desired shape. B-Series: B26, B36, B45X1, B50 BS-Series (Double Bending): BS36, BS45, BS50, BS60 (MG65 PRO) Product information: - Voltage: 380 V (16 A) - Motor Power: 2,2 kW - 6 kW Ijdjm Shffepfx Ahnjba - Ideal for your construction company or also for your construction sites - Left & Right Bending possible (in the BS-Models) - In addition to the individual bending process, a bending sequence can also be programmed - Head for different reinforcing steel Ø are included in the accessories (incl. accessories) - Possible in automatic or manual mode - Bending capacities depending on steel strength according to table (see pictures) - Optional available with digital control panel - Net weight: 215 kg - 850 kg Shipping: Europe-wide (self-collection also possible) If you have any questions, please do not hesitate to contact us!