EMMEDI HF WELDER 100KW

EMMEDI | GH INDUCTION HF WELDER 100KW

Condition: used, Year of construction: 1990, Technical details: x-travel: 185 mm y-travel: 95 mm z-travel: 200 mm Bedpfx Ajvc Awrob Uewk control: emco tronic TM02 spindle taper: SK 30 range of revolution per miute: 10 - 4000 / steples U/min feed continuous: 1 - 2000 / steples mm/min. rapid traverse: ca. 3,0 m/min tool turret - number of stations: 10 interface: R 232 table surface area: ca. 420 x 125 mm total power requirement: 0,8 kW machine dimensions LxWxH: 2,1 x 0,9 x 2,0 m EMCOTRONIC TM 02 control panel Operating modes: Manual operation (manual) and/or automatic Coolant system (with feed to the milling spindle) Operation via control panel standing on 3 swivel wheels Pneumatic door protection *

Condition: new, Year of construction: 2025, functionality: fully functional, power: 88 kW (119.65 HP), temperature: 220 °C, heating capacity: 30 kW (40.79 HP), workpiece height (max.): 1,500 mm, workpiece length (max.): 500 mm, insulation material: Steinwolle, insulation thickness: 150 mm, workpiece width (max.): 500 mm, Scope of delivery: 1. chemical pre-treatment by spraying (in cycle process) 2. dryer 3. powder coating system 4. single powder oven 5. conveyor technology, semi-automatic 6. electrical control system Hall/ floor space Floor area of the system max. 12,000 x 6,500 mm Hall floor Industrial floor Workpiece sizes Max. Part dimensions L= 500mm, H= 1,500mm, W= 500mm Range of steel parts Conveyor technology P&F chain conveyor in cycle mode, semi-automatic Bwsdpfx Absulwg Ns Ujk Pre-treatment Chemical Power supply Electricity On-site power (max. 88 kW) Gas On-site power Compressed air On-site power Water On-site power Calculation Type of system Cycle system Conveying speed 3.2 meters / min Length per cycle L = 1,600 mm Time for cycle movement: Tm = 1.6 meters : 3.2 meters/min = 0.5 minute Time for cycle standstill: Ts = 8.5-12 minutes Total time for cycle Tt = Tm + Ts = 9-12.5 min Electrical energy: Total power 88 kW min. Average consumption 60 kWh max. average consumption 70 kWh

Condition: new, Year of construction: 2025, functionality: fully functional, total length: 30,000 mm, total height: 4,300 mm, total width: 6,500 mm, workpiece weight (max.): 100 kg, temperature: 220 °C, heating capacity: 80 kW (108.77 HP), workpiece height (max.): 1,200 mm, workpiece length (max.): 2,500 mm, insulation material: Mineralwolle 75 kg/m³, insulation thickness: 150 mm, workpiece width (max.): 800 mm, The continuous system consists of the following components: Bwodpfx Absum Ufls Uok Chemical pre-treatment by spraying Dryer Powder coating system Powder curing oven Conveying technology (cycle process) Electrical control system

Condition: used, Year of construction: 2010, functionality: fully functional, Wagner Powder painting equipment for sale! Powder coating device, year 2010 consisting of: Booth: Prima Cube 16000 Powder supply: Powder Center Powder recovery: Cyclon Filter 16000 Movement generator: KHG 350 Production process configurations INCLUDING: I. Presumes Maximum size of parts: LxWxH=2600x400x1850 mm II. Equipment Technological Conveyor automatic speed V=1.2 mtrs/min. Speed regulation between 0.5-2.5 mtrs/min 1. Pretreatment Stand MNA-3-LPG, total size 16,7 mtrs Enter size L=2,5 mtrs a. Washing, degreasing and phosphating; L=3,6 mtrs -number of spray frames – 10 -number of nozzles in frame – 18 -number of nozzles in total – 180 -delivery of the pump – 162 m3/h -power of the pump – 15 kW -vessel 4 m3 for active liquid -inner heat exchanger with LPG burner – 160 kW -temperature 500C -mechanical oil separator - solution filter -the dosing system, membrane pump with regulator -washing time – 3 min b. Dripping zone L= 3,1 mtrs -time of dripping – 2 min 30 sec c. First rinsing; L= 1,2 mtrs -number of spray frames – 4 -number of nozzles in frame – 18 -number of nozzles in total – 64 -delivery of pump – 38 m3/h -power of the pump – 3 kW -vessel 1,5 m3 for water -first rinsing time – 1 min c. Dripping zone L= 3,1 mtrs -time of dripping – 2 min 30 sec d. Fine rinsing; L= 1,28 mtrs -number of spray frames – 3 -number of nozzles in frame – 18 -number of nozzles in total – 54 -delivery of pump – 33 m3/h -vessel 1,5 m3 for water -power of the pump – 3 kW -one extra spray frame -number of nozzles in frame – 18 -fine rinsing time – 1 min e. Dripping zone L= 2 mtrs -time of dripping – 1 min 40 sec Three openings to connect to exhaust system with three ventilators Operating space made of stainless steel. Pipes made of PVC or S/S. 1 unit 2. Automatic Dryer after water AST-1-KLPG: - operating space dimensions LxWxH=7000x3000x2800 - air curtains each side to avoid heat losses - one indirect heat exchanger heated with liquid petrol gas to produce 200 kW of rated power - three blowers 6000 m3/h of air delivery - two openings to connect to exhaust system - temperature sensor and temperature regulator - overheating sensor Bwedpfx Abeww Adte Uok - circulation sensor - operating space made of zinc plated steel - thermal insulation 200 mm thick - drying time 10 min 1 unit 3. Automatic Curing Oven APT-2-KLPG for curing powder paints - operating space dimensions LxWxH=10200x3600x2800 - air curtains on one side to avoid heat losses - two indirect heat exchangers heated with liquid petrol gas to produce 300 kW of rated power, of each - eight circulation blowers, capacity of each 6 000 m3/h - two openings to connect to exhaust system - temperature sensor and temperature regulator - overheating sensor - circulation sensor - operating space made of zinc plated steel - thermal insulation 200 mm thick - curing time 25 min 1 unit 4. An overhead rail conveying system ATR-ADAX, for the paint shop including the following: • straight track with hangers L=400 mm 146 mtrs • drive station 2 pc • tension station 1 pc • chain lubrication station 1 pc • drawing of the track supporting structure 1 set

Condition: new, Year of construction: 2026, The CORMAK H - 260SA column band saw is a highly efficient machine for cutting bars, pipes and profiles made of steel, cast iron and non-ferrous metals in an automatic cycle. The solid body and strong frame of the saw, combined with the column construction, provide excellent rigidity and an exceptional level of stability during the cutting process of even the most difficult metals to machine. The cutter is equipped with a PLC controller and an easy-to-use touch screen. Automatic band saw work on manual and automatic modes. Manual mode allows you to perform all activities manually from the machine's desktop. Automatic mode - after switching on the machine, the entire cutting cycle, i.e. fixing the cut detail in the vice, its shift to a specific dimension to the cutting tape, leaving the arm to cut and its raising to the desired height after finished cutting takes place without the operator's operation. Cutting parameters, such as the number of pieces of cut details, their dimensions, the speed of the cutting band, the speed of the arm's descent, are set on the control panel. The device automatically stops when the series is cut, the cutting band breaks or another failure identified by the cutter's control system is detected. The body of the machine is a cast iron set on a rigid, spatial plate structure of the casing. Inside the housing there are: a hydraulic unit, a coolant tank with a pump and a chip feeder. The drive of the cutting band based on an inverter-controlled motor ensures smooth regulation in a large range of speeds. The hydraulically forced lowering of the arm is regulated in a wide range by a precise throttle valve. The fast feed system allows you to shorten the time of cutting individual elements. Hydraulic material feeding system ensures a fully automatic working cycle of the machine. The controller equipped with an LCD display allows you to program the operation of the saw, signals the end of the material, communicates errors and informs about the number of cut sections after the programmed time. The maximum material feed length in one stroke is 500 mm with an accuracy of +/- 0.2 mm per stroke. Innovativeness and production of CORMAK semi-automatic and automatic series cutters according to norms and standards compliant with ISO:90001 and ISO:140001 certificates, guarantee safety, quality and product reliability. The use of motors licensed by a well-known and respected manufacturer on the global market, one of the world's leaders, ABB, guarantees long and trouble-free operation. Technical data Cut range Ø260 or 260 x 260 Tape 3150 x 27 x 0.9mm Cut speeds 40/60/80m/min Engine 2.2kW Hydraulic power pack 0.75kW Coolant pump 0.09kW Feeder stroke 500mm Load capacity 1500 kg Dimensions 1600 x 1800 x 1550mm Weight 1000 kg Max. cutting range angle 0º ø260 260 × 260 Standard equipment Bwjdpjiz S I Hjfx Ab Usk work in automatic cycle arm position memory function built-in hydraulic unit vise position memory function change cutting speed motorized belt cleaning brush cooling system bi-metal band saw CE Declaration of Conformity Manual in Polish and English For more information visit our web page

Year of construction: 2023, condition: used, sheet width 300 mm coil weight 1 t coil internal dia. 375-550 mm coil outside dia. 1600 mm weight of the machine ca. 0,5 t dimensions of the machine ca. 1500x1500x1900 m Bwsdpfelp U Tbsx Ab Ujk

Year of construction: 2017, condition: like new (used), Set for robotic laser welding Scope of supply: 1 x IPG YLS-4000 4KW output laser (2017). Fiber core 300 microns and 30 meter length, LCA LCA. Optical coupler inside. Profinet interface. Power ON work time : 32832 hours 1 x IPG CHILLER.(2017). 1 x HIGHYAG BIMO LASER WELDING HEAD with air knife. Machine can be inspected. Very good condition. Connected, can be tested. Bjdpfxerfucqe Ab Uswk Shipping to EU countries is our responsibility and the shipping cost is free.

Condition: new, Year of construction: 2025, operating hours: 10 h, functionality: fully functional, Fiber laser welding machine with 2000-watt laser power 4-in-1 device Welding with automatic wire feed Welding without wire Cleaning Cutting - Top device at a top price from our showroom - approx. 10 operating hours - 2kW laser source by MaxPhotonik - German-language menu navigation - Universal device for welding / cutting / cleaning - incl. 4-roller welding wire feeder - integrated water cooling - immediately available Also take advantage of our attractive leasing/financing offers. Approx. machine dimensions: Width: 60cm Height: 120cm Depth: 110cm Weight: approx. 150kg Bedpfeug Unfox Ab Uswk

Condition: new, Year of construction: 2025, functionality: fully functional, type of input current: three-phase, laser power: 3 W, Parameter: JSW-3000 Laser power: 3000W Laser source life: 100,000 hours Laser wavelength: 1064 - 1070 nm Cable: 10 m (15 m on request) Operating temperature: -10 - 45 ℃ Working environment humidity: 10 - 90% Positioning: Laser pointer (red dot or line) Protective gas: Nitrogen / Argon / Oxygen Power supply: 3-phase 380V, 50/60 Hz Maximum total power consumption: 24.6 KVA / 37.4 A Average power consumption: 14.7 KVA Indication of the device operating status: Operating status indication of the cooling unit, the temperature of the protective glass and the temperature of the controller Thickness of welded plates: 0.5 - 8 mm Maximum groove width: ≤ 2 mm Laser beam width in cleaning mode: 0 – 70 mm Bodewf I R Uspfx Ab Uewk Cooling method: Water-based Control method: Touch panel / screen and PLC Wire feeder: Fully automatic Machine weight: 195 kg Machine dimensions: Height: 1050 mm Width: 530 mm Length: 1240 mm Material capacity for welding mode (JSW-3000W) Stainless steel: 0.5 – 8 mm Carbon steel: 0.5 – 8 mm Galvanized sheet: 0.5 – 8 mm Aluminum: 0.5 – 6 mm

Condition: used, Year of construction: 2010, operating hours: 16,000 h, functionality: fully functional, machine/vehicle number: E1053A0012, overall weight: 850 kg, total height: 1,940 mm, total length: 1,700 mm, total width: 950 mm, Specification: Protection class: IP54 Power: 16kW/17 kVA 24A at 400V Frequency: 50-60 Hz Supply voltage: 380V (-10%) to 460V (+10%) Bsdpfxewq Rmpo Ab Uswk The Trumpf Laser TruDisk 2602 is a robust and powerful laser system, perfectly suited for demanding industrial applications. It features high precision and efficiency, enabling fast and high-quality cutting operations on various materials. Thanks to its compact design, the system can be easily integrated into existing production processes.