Used Biesse Rover 24 for sale (336)

Condition: used, Year of construction: 2018, Numerical Control BH 660 with BIESSE BSolid software bEdge module for edge management bSolid surface design Sophia - IoT Connection Office control Working range on X-axis mm 3228 Working range on Y axis mm 1580 Working range on Z axis mm 200 with H74 mm suction cups Working range on Z axis mm 245 with H29 mm suction cups No. 8 adjustable ATS panel support bars Installation of the pneumatic lock divided into two zones in Y No. 6 Pneumatic Bakelite bars for panel lifting No. 3 adjustable suction cups for bar Set-Up Assistant for Suction Cups No. 1 electrospindle (pantograph) with 4 axes, automatic tool change, KW 13 (HP 17.4) motor, cooling liquid, HSK cone attachment, 20000 RPM Automatic tool change with 16 positions on the X-axis of the carriage Drilling tesa BH17 independent spindles arranged as follows: No. 5 independent spindles for vertical drilling in the "X" direction No. 5 independent spindles for vertical drilling in the "Y" direction No. 4 spindles for horizontal drilling in the "X" direction No. 2 spindles for horizontal drilling in "Y" direction No. 1 blade integrated into the drilling head diam 120 mm (useful cut 25 mm) GU60L gluing unit for EVA glue with pre-melter - edge pressure system with double rubber roller for spokes maximum internal 30 mm and edge joint sensor - 500 ml glue pot installed on the glue roller - lamp edge heating - edge feed system - edge cutting system - possibility of Introduction of the manual edge Plastic edge thickness from 0.4 to 3 mm Wood edge thickness from 0.4 to 2 mm Laminated edge thickness from 0.4 to 1.2 mm Maximum edge width 65 mm Workpiece thickness from 10 to 60 mm Minimum internal radius workable with 30 mm edging Maximum external radius for edging, proportionate to the thickness and stiffness of the edge: * 10 mm with edge up to 1 mm thick * 20mm with 2mm thick edge * 30mm with 3mm thick edge Minimum dimensions of the edging panel 300 x 300 mm Minimum internal diameter for edging: 350 mm with plastic edges less than 1 mm thick and with panel maximum thickness 18 mm 2-position edge storage unit positioned inside the protective casings for edges with maximum thickness 65 mm Finishing aggregate cleaning station with automatic dispensing of special cleaning liquids and with a cleaning cycle No. 1 aggregate for edge trimming / rounding No. 1 EF60A combi aggregate trimmer / edge scraper / glue scraper Perimeter protection grids Chip evacuation system with motorized belt Cedpfsugpwnjx Ab Usgr Liquid cooling system Automatic lubrication system No. 1 vacuum pump of 250 m3/h TECHNICAL DETAILS TO BE CONFIRMED

Condition: new, Year of construction: 2022, axis stroke (X,Y,Z) 3100 x 2205 x 170 mm Number of spindle head vertical 0 St. Number of spindles head horizontal 0 St. Number of tools 14 St. Dust suction hood 200 mm Number of milling agregates 1 St. Cgodpfx Absxfwduj Uer Year 2022 Speed 24.000 U/min. Required air-pressure 7 bar Motor output 9 kW Capacity 2x 250 m³/h Control BH660

Condition: new, Year of construction: 2022, axis stroke (X,Y,Z) 6735 x 1930 x 245 mm Number of spindle head vertical 0 St. Number of spindles head horizontal 0 St. Number of tools 39 St. Dust suction hood 2x 250 mm Cgodpfxjxf Dwzs Ab Uor Number of milling agregates 2 St. Year 2022 Speed 18.000 / 24.000 U/min. Required air-pressure 7 bar Motor output 16,5 / 19,2 kW Capacity 250 m³/h Control BH660

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, travel distance X-axis: 3,280 mm, travel distance Y-axis: 1,320 mm, travel distance Z-axis: 170 mm, number of slots in tool magazine: 12, Machine is provided "free loaded on truck". No dismantling and loading costs! TECHNICAL DETAILS X-axis travel: 3,280 mm Y-axis travel: 1,320 mm Z-axis travel: 170 mm CNC control: BiesseWorks Working beams: 6 pieces Cgedpfovvvcbox Ab Ujr Suction cups: 18 pieces Tool magazines: 12 MACHINE DETAILS Total weight: 3,000 kg Electrics Input voltage: 400 V Type of input current: AC Required power: 25 kW EQUIPMENT - Safety mats - BECKER vacuum pump

Condition: used, CNC machining center BIESSE Rover C 6.50 CONF.2, year 2007 Working area: approx. 140 × 460 cm Machine dimensions: 300 × 650 cm Weight: approx. 6,100 kg Two working heads Tool magazine: 22 positions Vertical drilling spindles: 28 pcs Horizontal drilling spindles: 12 pcs Price negotiable, available immediately. Cgodpfxow Rpd Ss Ab Usr Price is without VAT.

Condition: used, Year of construction: 1999, functionality: fully functional, travel distance X-axis: 2,900 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 140 mm, number of slots in tool magazine: 7, controller manufacturer: XNC, feed rate X-axis: 75 m/min, feed rate Y-axis: 75 m/min, feed rate Z-axis: 15 m/min, spindle motor power: 11,000 W, number of spindles: 1, spindle speed (max.): 24,000 rpm, spindle speed (min.): 1,000 rpm, Equipment: CE marking, chip conveyor, documentation/manual, rotational speed infinitely variable, Biesse Rover 23 woodworking center – fully equipped Still in use to this day, 1 to 2 days a week, but for sale due to business closure in Slovakia. Always well maintained. ✅ Powerful performance Milling spindle with ceramic bearings (11 kW) Adjustable speed: 1,000 – 24,000 rpm Drilling head with 10 vertical and 6 horizontal drills Circular saw on the X-axis ✅ Efficient & flexible Pneumatically adjustable vacuum pods in 6 rows, 3 per row 100 m³ vacuum pump Tool magazine with 7 positions (ISO 30) Cedpfow S Edwsx Ab Usgr All adapters and tools included ✅ User-friendly Conveyor belt for automatic chip removal Immediately operational, fully equipped 📍 The machine is located in Slovakia and must be disassembled and collected by the buyer on site.

Condition: good (used), Year of construction: 2007, machine/vehicle number: 94323, travel distance X-axis: 3,060 mm, travel distance Y-axis: 1,260 mm, travel distance Z-axis: 150 mm, total height: 2,400 mm, total length: 4,400 mm, total width: 2,800 mm, overall weight: 3,130 kg, I will sell a MACHINING CENTER IN CONTINUOUS OPERATION CNC machining center Biesse ROVER 3.03 functional to view in Wadowice Feed X 3060 mm Feed Y 1260 mm Cgedpfxjwpthtj Ab Usr Feed Z 150 mm Control type CNC XP 600

Condition: good (used), Year of construction: 2018, machine/vehicle number: 1000028154, functionality: fully functional, Equipment: rotational speed infinitely variable, The machine was commissioned in 2019, single owner. It has seen very little use. Cgsdpexdl H Usfx Ab Usr Description Useful working area, 5-axis configuration: X=3280mm, Y=1600mm Axis travel: X=3706mm, Y=2294mm, Z1=515mm, Z2=371mm Axis traverse speed: X=80m/min, Y=60m/min, Z=30m/min Electrospindle: HSD, 5 axes 11 kW, with continuous 360° rotation on B and C axes, enabling high-precision machining of complex shapes liquid-cooled Drilling head: HSD 20 vertical spindles 4 horizontal spindles grooving discs on X-axis grooving discs on Y-axis Work table: 6 cross beams Isbjwhypnjni Itxtobb 4 suction cups per beam preparation for uniclamp Tool magazines: 16-position revolver-type tool changer Vacuum system: Vacuum pump with a capacity of 250 m³/h, ensuring firm clamping of the parts during processing

Condition: new, machine/vehicle number: 1000007776, CONTROL SYSTEM • Numerical control, PC-based • bSolid software • CAD-CAM 3D module – 3-axis working module – bEdge module TECHNICAL FEATURES • Usable working area (X-Y-Z): approx. 4,320 x 1,600 x 200 mm • Usable working area for edgebanding (X–Y): approx. 3,300 x 1,500 x 60 mm PANEL SUPPORT AREA • 2 independent working zones on the X axis • 10 Set-Up Assistant (SA) working tables for panel support, with manual positioning and illuminated position/direction indicators – 32 rails • 8 lifting bars for loading support • 28 stops (8 rear stops, 8 intermediate stops at 670 mm, 6 side stops, 6 central stops) each with descent verification sensors • 1 vacuum pump, 100 m³/h DRILLING/SAWING UNIT • 1 extra 'Z' pod for rear working unit • 1 BH 24 L boring head Csdow Nip Sopfx Ab Uogr GROOVING/MILLING UNIT • 1 electrospindle, 13.2 kW (17.7 HP), HSK F63 tool clamping system, air-cooled, equipped with a 360° working unit and gear C-axis torque • 1 air blowing system with 4 nozzles • 1 revolver tool changer with 16 positions on the X pod EDGEBANDING UNIT • GU60L edgebanding unit for EVA and PUR adhesives, including: – glue pot for EVA and glue pot for PUR – pre-melter for EVA glue – double pressure roller for edgebanding radii up to 30 mm; closed-loop joint sensor • 1 edge magazine for 2 coils positioned on the X pod • 1 edge magazine for 2 coils outside the machine • 1 blower unit for panel cleaning prior to edgebanding • 1 cleaning station for edge trimming units • 1 HSK F63 aggregate for blade diameter max. 215 mm • 1 combined unit for rough trimming, edge scraping, and glue scraping EF60A • 1 unit for edge rounding and end trimming • 1 kit for narrow panels 10-60 mm (edge max. 2 mm) and 12-60 mm (edge max. 3 mm) PREDISPOSITIONS AND ACCESSORIES • Automatic lubrication system • Waste extraction system for wood chips SAFETY STANDARDS AND OPTIONS • Copy of original EC Declaration of Conformity • Bumper system and double front/rear photoelectric safety barriers

Condition: used, Year of construction: 2014, CNC Machining Center Biesse skill 12 24 G FT Year of construction 2014 Machine no. 60961 Recording HSK F63 10x vertical drilling 12 switch positions Software: BiesseWorks X axis 2465 mm Y-axis 1260 mm Z axis 324 mm Disassembled for transport on normal trailer; 4500x2200x2400mm; Cgedpfx Aewnhanjb Ujr Own weight 2000kg - Details: - └ Description: Pallet with white control box does not belong to this machine - Year: 2014 - Documentation available: Yes - CE certificate present: No - Serial number: 60961 - Number of milling spindles [pcs.]: 1 - Type milling table: Flat table - Tool clamping system: HSK-F63 - Drilling unit present: Yes - └ Vertical drilling spindles [pcs.]: 10 - Tool changer positions [pcs.]: 12 - System/software: BiesseWorks - Safety feature: Enclosed fence - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - Working range X [mm]: 2465 - Working range Y [mm]: 1260 - Z-axis working range [mm]: 324 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: like new (used), functionality: fully functional, Ferwood code: RS0003524 - Manufacturer code: 2420A0716 - Condition: As new (showroom item) - Functionality: Fully functional - Compatible machine: - If interested, we offer refurbishment service, please contact us. 1.5KG 36X26X21 Cgedpfxjymfgbo Ab Uer

Condition: used, Pressure gauge BIESSE 2424A0007, Codpfx Ajlkchyob Ujgr

Condition: excellent (used), functionality: fully functional, EDGE BANDING machine model BIESSE AKRON 245 second hand machine CE regulation : Yes with Instruction Booklets for the application of edges in wood, pvc, veneer, melamine, abs for furniture, furnishings, kitchens, bathrooms, doors, panels and various NC 321 electronic positioner Technical data: min. height of gluing panel mm.10 max. height of gluing panel mm.45 min. thickness roll edge mm.0.4 max. thickness roll edge mm.3 max. thickness wood edge mm.8 min. panel width mm.50 min. panel length mm.150 feed speed motor power Hp 2 electric press lift telescopic support for large panels soundproof cabin Composition: Cgedpfx Abjgipk Aj Uer gluing group with glue tank pressure rollers edge feeder end-cutting unit for front and rear vertical cutting of the excess edge n.2 motors trimming unit with overlapping motors for trimming the upper and lower part of the excess edge . n.2 motors tilting trimming unit for the final upper and lower trimming of the excess edge . n.2 motors glue scraper group for cleaning glue residues overlapping brush group for brushing and polishing the applied edges . n.2 tiltable motors Compressed air 7-8 bar Weight kg 1700

Condition: like new (used), Year of construction: 2019, I sell the edge banding machine Biesse JADE 240 Year 2019. Special offer: Machine almost NEW !! Configuration: Entry fence manual adjustable Premilling pneumatic adjustable Edge banding manual adjustable / 2 glue tanks for EVA glue Pressure zone manual adjustable End cutting saw pneumatic adjustable Tilting radius milling manual adjustable Corner rounding unit 2-motor manual adjustable Cedjxncrvepfx Ab Uogr Radius scrapers manual adjustable Glue scrapers pneumatic adjustable Polishing brushes Separation fluid spraying front Central lubrication system Top feeding rolls Height adjustment manual Material height 10-60 mm Edge thickness 0,4-8,0 mm Feeding speed 12 m/min. Only 9250 meters edgebanded. Machine almost NEW !! CE Mark. Including full documentation and CDs. Very good condition ! Available immediately !

Condition: used, machine/vehicle number: 008490, X axis working area: 3657 mm Y axis working area: 1524 mm Working Table: Flat table Main Electrospindle power: 12 KW Number of controlled axes: 3 axes Total number of drilling spindles: 10 Cgsdpfjyxmwaox Ab Usr Total number of tool changer positions: 12

Condition: used, machine/vehicle number: 008109, Type of edging: Thin edge, Thick edge, Solid wood Csdpfx Aew Idc Dsb Uegr Gluing System: EVA Hotmelt Premilling Unit: yes Corner Rounding Unit: yes Maximum panel thickness: 12 mm Operating Units: 9 nr

Year of construction: 2012, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: BCOR12150, BIESSE BREMA EKO 902 CNC and vertical dowel insertion machine for reduced cycle times Equipment Features - Clamping grippers measure the thickness to adjust drilling depth - Laser-based measuring system for detecting the front and rear panel edges - Length tolerance compensation correcting the workpiece length in X - 5-position tool changer - Drilling head with individually retractable spindles and grooving saw - Diameter: 120 mm - Gluing and dowel insertion units mounted on Y and Z axes Options - 4.5 kW electrospindle; 18,000 rpm - Special drilling unit for hinges Technical Data - Panel length: 160 - 3200 mm - Panel width: 35 - 900 mm - Panel thickness: 8 - 80 mm - X/Y/Z axis speed: 100 / 60 / 30 m/min - X axis travel: 3200 mm - Y axis travel: 900 mm - Main spindle power: 4.5 kW - Number of controlled axes: 3 axes Csdew Nytnopfx Ab Usgr - Number of drilling spindles: 20 - Number of tool positions: 5

Condition: used, Year of construction: 2014, Empty weight: 4.000 kg Price: On request - Machine available from: 2026-01-26 - Year: 2014 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 89867 - Number of milling spindles [pcs.]: 1 - Type milling table: Flat table Cjdpfxsxr Evle Ab Uogr - Tool clamping system: HSK-F63 - Drilling unit present: Yes - Saw unit present: Yes - Tool changer positions [pcs.]: 12 - System/software: BiesseWorks - Safety feature: Safety mat - CNC options: Label machine, Loading system, Unloading system - Table length [mm]: 3600 - Table width [mm]: 1800 - Transport weight [kg]: 4000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2020, total height: 2,100 mm, total length: 2,000 mm, total width: 2,500 mm, Price: On request Cgodpfx Abjx Ad R Ne Usr - Machine available from: 2025-12-15 - Year: 2020 - Documentation available: Yes - └ Type Documentation: Operating system, Technical data, User manual, Electrical diagrams - CE marking present: Yes - CE certificate present: No - Serial number: 1000040377 - Main motor power [kW]: 10 - Number of controlled axes [pcs]: 3 - Working range X [mm]: 975 - Working range Y [mm]: 1321 - Working range Z [mm]: 243 - Number of milling spindles [pcs]: 1 - Tool holder interface: ISO30 - Spindle diameter [mm]: 16 - Min. spindle speed [rpm]: 1000 - Max. spindle speed [rpm]: 18000 - Horizontal drilling unit: Yes - Horizontal drilling spindles [pcs]: 10 - Vertical drilling unit: Yes - Software: Biesse works - Saw unit present: Yes - Safety feature: - Spindle speed control: Variable - Voltage [V]: 400 - Current consumption [A]: 18 - Fuse [A]: 32 - Power [kW]: 10.0 - Transport dimensions: 2000mm x 2500mm x 2100mm (l x w x h) - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: excellent (used), Year of construction: 2023, Biesse Akron 1330 A Edgebander Single-sided edgebander AKRON 1330-A Gluing Unit SP03 End trimming Unit IT03 Fine trimming Unit RF02 Corner rounding Unit AR02 PRE-MILLING UNIT RT02 Symmetrical diamond tools H=45 mm Z=2+2 30° included. EDGE SCRAPER RB02 Tools are not included. GLUE SCRAPER UNIT RC02 BRUSHING UNIT SZ02 SUPPLEMENTARY LATERAL PANEL SUPPORT KIT FOR THE INSTALLATION OF THE PANEL RETURN SYSTEM MANUAL INFEED SYSTEM FOR NARROW PIECES KIT FOR PROCESSING "SHADOW LINE" PROFILE PANELS STRAIGHT AIR TABLE AT THE MACHINE INFEED ANTIADHESIVE UNIT ADZ02 PAIR DIAMOND-COATED MILLING CUTTERS H=65 mm Z=2+2 30°.In replacement of standard tools. HYBRID GLUING CHUCK FOR GRANULATED EVA/PUR GLUE INSTEAD OF THE STANDARD SYSTEM TM15 HYBRID PREMELTER FOR EVA/PUR GLUE ADAPTIVE INFRA RED LAMP AdIRL-700 AX-4, NC AXIS ON FINE TRIMMING UNIT PRO-NESTING KIT FOR FINE TRIMMING UNIT Pair of multiprofile milling cutters for fine trimming unit: chamfering 25 degrees, R=2 mm + R=1 mm, straight profile for solid wood AX-2, NC AXIS ON CORNER ROUNDING UNIT ROUNDING FUNCTION ONLY SLIDING UNIT FOR CORNER ROUNDING UNIT Pair of milling cutters, R=2 mm, for corner rounding unit Pair of milling cutters, R = 1 mm, for corner rounding unit AX-4, NC AXIS ON EDGE SCRAPER PRO-NESTING KIT FOR EDGE SCRAPER UNIT Pair of knives R=2 mm, for edge scraper Pair of knives R=1 mm, for edge scraper CLEANING UNIT LPT02 (Despite our great care all changes, mistakes in technical data, prices and all information is subject to (typing) errors. No guarantee on printed data! Availability subject to prior sales). (Trotz größter Sorgfalt bleiben Änderungen, Irrtümer bei technischen Daten, Preisen und allen Angaben (Tipp-)Fehler vorbehalten. Keine Gewähr auf gedruckte Daten! Verfügbarkeit vorbehaltlich Zwischenverkauf). Prices excl. advertisement cost MachineSeeker / Preise exkl. Inserierungskosten MaschinenSucher Codpfx Abeyyb Ico Ujgr Best woodworkingmachines from the Netherlands Holland Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland

Condition: good (used), Code: 0278 Brand: COMIL BIESSE Model: COSMO Self-adjusting clamp press for furniture, furnishings, kitchens, bathroom furniture and various Working length max mm 2500 Working height mm 1200 Cgsdpfx Aeyyzvgeb Uer Working width mm 700 Positioning speed 3,5 mt/min Total power Kw 3,7 Overall dimensions: mm 3760 x 920 x 2280 h Weight kg 2200

Condition: excellent (used), ELECTRONIC (CNC control) machine, Numerical Control Type NC 500 - Software Tooling System N. 2 Through-feed motorized conveyoring belts - Feeding speed (m/min) 35 - 75 ca. Max. working width (mm) 3200. Min. working width (mm) 215 N. 2 Horizontal units/supports N° 2 Drilling heads for each horizontal unit (11 Spindles for each horizontal drilling head) N. 5 Bottom vertical units/supports Drilling heads/blocks for each bottom vertical unit (N°) 2 x HP 1,8 N. 2 Top vertical units/supports Drilling heads/block for each top vertical unit (N°) 2 x HP 1,8 N. 4 Vertical top pressure clamps - N. 2 Motorized endless screws to evacuate wastes/chips Quota (axes) digital display. Total installed power (Kw) 62,7 The CNC controls the movement (X axe) of the mobile horizontal unit Cedpfx Aoyyw S Reb Ujgr The CNC controls the vertical movement (Hv) of the 2 horizontal units The CNC controls the movement (X axe) of all the vertical units The CNC controls the movement (Y1 and Y2 axes) of the boring heads The CNC controls the movement (Y axe) of the stops The CNC controls the movement (X axe) of the pressure clamps The CNC controls the movement (X axe) of the conveyor belts The CNC controls programming of the working cycles

Condition: excellent (used), Numerical Control Type NC 400 Deluxe Through-feed motorized conveyoring belts (No.) 2 No. 2 Horizontal units/supports Drilling heads for each horizontal unit (N°) 1 Splindles for each horizontal drilling head (N°) 20 Max. working width (mm) 3200 Min. working width (mm) 205 (ca.) Cgodpsyyw Sdefx Ab Uor No. 5 Bottom vertical units/supports Drilling heads/blocks for each bottom vertical unit (N°) 2 No. 2 Top vertical units/supports Drilling heads/blocks for each bottom vertical unit (N°) 2 Vertical top pressure clamps (N°) 4 Transport belts to evacute chips (wastes) (N°) 2 The CNC controls the movement (X axe) of the mobile horizontal unit The CNC controls the movement (Y axe) of the stops The CNC controls the movement (X axe) of the conveyor belts Total installed power (Kw)

Condition: excellent (used), Angular sawing plant Numerical Control OSI Plus - Software Optiplanning N. 2 Pre-loading roller tables (mm) approx. 4500 x 2200 each Lifting table (mm) 4500 x 2200 1° Rear-pusher, with No. 5 clamps/grippers Turning device (rotating unit) at 90° 1° Panel saw (longitudinal) max. cutting width (mm) 4500 Max blade projection (mm) 152 Scoring Unit (max. diameter saw) mm approx. 215 Main Sawing Unit (max. diameter saw / power) mm 530 ( Kw 30) Adjustable speed of the saw carriage (m/min) 1 - 170 m/min Cutter for shredding trimmings 2° Rear-pusher, with No. 10 clamps/grippers 2° Panel Saw - Max cutting width mm 2200 Max blade projection (mm) 152 Scoring Unit (max. diameter saw) mm approx. 215 Main Sawing Unit (max. diameter saw / power) mm 530 (Kw 30) Adjustable speed of the saw carriage (m/min) 1 - 170 m/min No. 2 Front supporting tables with Air blowing system mm 2200 x 1500 Cgedpsukhd Ajfx Ab Uor Automatic unloader (bridge) for cut panels "RBO (BIESSE)" Mod. Lifter with 6 stacking stations

Condition: used, Year of construction: 2005, Biesse Comil Cosmo NK Corpus press Cgedpfjywxzzox Ab Ujr Year of manufacture: 2005 Press dimensions: 2500 x 1300 mm Press cycle: Automatic Press type: Motorized Motor power: 3.7 kW Press pressure: 12,000 N (Despite our great care all changes, mistakes in technical data, prices and all information is subject to (typing) errors. No guarantee on printed data! Availability subject to prior sales). (Trotz größter Sorgfalt bleiben Änderungen, Irrtümer bei technischen Daten, Preisen und allen Angaben (Tipp-)Fehler vorbehalten. Keine Gewähr auf gedruckte Daten! Verfügbarkeit vorbehaltlich Zwischenverkauf). Prices excl. advertisement cost MachineSeeker / Preise exkl. Inserierungskosten MaschinenSucher Best woodworkingmachines from the Netherlands Holland Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland