Used Calibrating for sale (1,004)

Year of construction: 2004, condition: excellent (used), Known K&S 8020 Specifications Specification Value Bonding type Automatic thermosonic ball bonder Wire material Gold wire (Au) Bond head Voice-coil direct-drive bond head Ultrasonic transducer 120 kHz unibody transducer with adaptive USG Kjdpezdgm Defx Abvjdn Vision system 20/20 vision system Camera Sony XC-75 CCD Bond pitch capability Sub-70 µm pitch kit available Bond area 2.0 × 2.3 in (≈ 50.8 × 58.4 mm) Optics Universal optics with increased depth of field Illumination LED Workholder 250-series heated manual workholder Power 208 V, 50/60 Hz Control Software-controlled automatic bonding programs Typical Process Capability The 8020 was developed to provide: Fine-pitch bonding Long, low wire loops Improved process control High throughput for leadframe and laminate packages Automated vision alignment and pattern recognition These capabilities were key selling points of the 8000 family. Applications Plastic IC packages SOIC, QFP, TSOP Memory devices ASICs Hybrid microelectronics Chip-on-board assemblies Physical Characteristics Unfortunately, a complete factory datasheet with dimensions, weight, XY-table resolution, bond-force range, and supported wire diameters is not readily available in public archives. Most of the available information comes from listings of used equipment and K&S annual reports. If you need details such as: Bond force range (grams) Wire diameter range (e.g., 0.7–2.0 mil) XY positioning resolution Air requirements Maintenance manual Error codes or calibration procedures

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, working width: 1,300 mm, overall weight: 4,700 kg, height adjustment type: electric, Wide-belt sanding machine Manufacturer: Viet Type: S3 223 TM Year of manufacture: 2006 (CE) Well-maintained calibrating and fine-sanding machine from a small carpentry/manufacturing workshop, suitable for sanding solid wood, veneer, and lacquered surfaces. Ksdpfjzd Ayljx Abvedn Working width: 1300 mm Constant table height, motorized height adjustment of the machine’s upper part (the machine is also suitable for inline operation). Automatic workpiece detection, thickness measurement, and infeed protection. 1x cross-sanding unit, sanding belt dimensions: 150 x 5520 mm 1x combination unit with calibrating roller and electronic segmented sanding shoe, segment pitch: 25 mm 1x cleaning brush for removing dust from workpieces 1x ionizer to prevent static charging Feed rate infinitely adjustable Vacuum transport for small, short, or slippery workpieces (e.g., lacquered parts) Operating voltage: 400 V, 50 Hz, 3 phases Dimensions: approx. 2500 x 2850 x 2280 mm (L x W x H) Weight: approx. 4700 kg

Condition: used, functionality: fully functional, Sales Description – Keyence XM-T1200 including accessories Kjdpfszdnxyox Abvsdn For sale is a high-quality Keyence XM-T1200 3D coordinate measuring machine including extensive accessories. The system is ideal for precise dimensional measurements, quality control, and flexible measuring tasks in manufacturing, toolmaking, and production. The XM series from Keyence impresses with its ease of use, high measuring accuracy, and fast measurement results – even with complex components. Thanks to the optical measurement support and intuitive software, measurements can be performed efficiently and reproducibly. Equipment / Scope of supply Keyence XM-T1200 Control and operating unit Original accessory package Probes / measuring sensors (depending on the configuration) Calibration accessories Software / documentation (if available) Further accessories by arrangement Technical highlights Precise 3D measurements Simple and user-friendly operation Flexible positioning of the measuring sensors Fast commissioning without complex fixtures Ideal for single parts, series production, and quality inspection Condition The machine is in well-maintained and fully functional condition. Maintenance and operation were carried out carefully. An inspection or demonstration is possible by arrangement. Sale Location: Hanns-Martin Schleyer Str. 2 // 41199 MG Availability: by arrangement Price: Negotiable / on request If you are interested or have any questions, please do not hesitate to contact us. We will be happy to send you further photos, technical details, and information about the accessories.

Condition: used, Bütfering Optimat SBO 109K Wide-belt calibrating fine-sanding machine Combination unit with contact roller and sanding shoe Steel contact roller with adjustable height and grit compensation Working width 950 mm Control panel with LED thickness display Thickness adjustment and feed rate adjustable via a multi-function lever on the control panel Motor power approx. 11 kW Ksdpfszcanlox Abvsdn 2 feed speeds: 4 / 8 m/min. Machine is WORKSHOP REFURBISHED and in TOP CONDITION From a craft business Available from stock in Lieboch

Condition: new, Year of construction: 2026, Top quality made from high-strength structural steel Q355, including plasma nitriding and calibration. 3D perforated table 4000 x 2000 x 200mm, 100mm grid, plate thickness 20mm, hole diameter 28mm. Surface finish machined, very robust, weight approx. 2400 kg. With table base, adjustable in 8 positions. Price excludes accessory set, surcharge €500. Packed in a wooden crate, shipping on request. The stated price refers to the table in standard version without plasma nitriding (last 4 pictures). Price for high-strength steel Q355, stainless and impact-resistant including plasma nitriding: surcharge €1800 (as shown). Kdjdpfx Absyg Ex Dsvjn

Condition: excellent (used), Weiss Spray Water Test Unit Type: SWT 600/800-S Manufacturer: Weiss Umwelttechnik GmbH For sale is a professional spray water test unit from the manufacturer Weiss Umwelttechnik. The unit is used to perform standardized water, spray water, and ingress protection tests according to IPX1, IPX2, IPX3, IPX4, IPX4K, and IPX9K. Ideal for industry, automotive, electronics, quality assurance, development, testing laboratories, as well as research and material testing. Operation is via an integrated touch control panel. Test sequences can be automated. Unit Manufacturer: Weiss Umwelttechnik GmbH Type: SWT 600/800-S Spray Water Test Unit Test types: IPX1 IPX2 IPX3 IPX4 IPX4K IPX9K Stainless steel test chamber Rotating test table Swivel arm system Water circulation Existing test accessories Electrical data Supply voltage: 3/N/PE AC 400 V ±10 % Frequency: 50 Hz Rated power: 17 kW Rated current: 30 A Wiring diagram no.: 82962 CE marking available Water supply Water inlet: R 3/4" Water outlet: R 1 1/4" Supply pressure: approx. 2 to 6 bar Test pressure IPX9K: approx. 80 to 100 bar adjustable Technical data Turntable speed: approx. 1 to 5 rpm Swivel speed: approx. 60°/s Permissible ambient temperature: approx. 10 °C to 35 °C Noise level: approx. 88 dB(A) Heat dissipation to the environment: Average approx. 1 kW Maximum approx. 3.5 kW Equipment Touch control panel Stainless steel test chamber Rotating test table Swivel arm Water circulation pump Nozzle ring / spray ring High-pressure unit Flow meter ESD earth bonding point CE marking Robust industrial design Dimensions / Weight Test chamber SWT 600/800: approx. 2,350 x 2,400 x 2,650 mm Test chamber without hinges and door locking: approx. 2,350 x 2,400 x 1,850 mm Weight of test chamber: approx. 650 kg Dimensions of high-pressure unit: approx. 850 x 1,200 x 800 mm Weight of high-pressure unit: approx. 380 kg Total weight: approx. 1,030 kg Kdsdpozachcefx Abvsn Documents Operating manual EC declaration of conformity Quality test certificate Technical documentation as shown in the pictures Accessories Nozzle ring / spray ring Test and spray components Swivel arm accessories Flow meter Connection components Tools and keys Documentation Condition Used unit from industrial use. Visual condition see pictures. The unit can be switched on. Display and user interface are functional and visible. Further technical testing, calibration or complete functional testing has not been carried out. Inspection and testing on site possible and desired after prior appointment. Scope of supply Weiss Umwelttechnik SWT 600/800-S spray water test unit High-pressure unit Turntable and swivel arm Test and spray accessories as shown in the pictures Operating manual and documentation Accessories as shown in the pictures The table shown in the photos is not included in the scope of supply. Loading possible by arrangement. Transport and shipping by a suitable freight forwarder required. Dimensions, weights and technical data partially taken from documents. Information may vary. Commercial sale without warranty. Subject to change, errors and prior sale.

Condition: as good as new (ex-display), Year of construction: 2023, operating hours: 31 h, 3D Coordinate CNC measuring device Profitech Innometrik Advanced in gantry design (demo unit at a special price) Open Cable Special features of the gantry design: Gantry design with a low center of gravity, wide bearing separation and optimum stiffness to mass ratio. The granite guideways ensure a uniform thermal, dimensional, torsional and geometric stability of the machine. 24 air bearings for smooth movement of the three axes. High dynamics for better performance, the machine can achieve high accelerations like comparable medium and large CMMs. Thermally compatible materials and components minimize the influence of ambient temperature fluctuations on measurement results, Air filter and regulator. Z-axis pneumatic counterweight system. Granit table with thread inserts of size M10. Passive vibration isolation pads Technical specifications Measurement paths: X: 500mm Y: 600mm Z: 400mm Max workpiece weight: 250kg Weight of the machine: 850kg Dimensions over everything: 1290x1160x2350mm Accuracy according to DIN EN ISO 10360-2 or ISO 10360-4: Volumetric probing deviation: MPEP = 2.2μm Volumetric length measurement deviation: MPEE = 2.2+ L / 350 (μm) Environmental conditions: Kdodpfx Abjdyah Sevjn Room temperature standard: 18-22 ° C Operating temperature 10-35 ° C Air Supply: Minimum air pressure: 6bar Air consumption: 90NI / min Also configurable as a complete package with touch probe, software commissioning and training. (Annual maintenance & calibration can also be offered)

Condition: good (used), functionality: fully functional, Year of construction: 2011, controller model: Rexroth IndraMotion MTX, laser type: CO₂ laser, laser power: 4,000 W, punching force: 22 t, Equipment: CE marking, nozzle changer, safety light barrier, Standard Equipment: Machine - Work area 3050 x 1550 mm - Robust, easily accessible C-frame - Coordinate guidance for highly precise machining - Linear magazine with 21 tool positions and 4 clamping claws - Drives with maintenance-free three-phase motors - Repositioning device with programmable clamping system - Foot pedal for closing clamping claws - Ball tables - Two parts collection containers - Chip container - Initial oil fill - Transport and assembly device - ContourLine - FocusLine - NitroLine - FastLine - FlyLine - PlasmaLine - Additional Xp and Yp axes - Ejection cylinder for laser parts - Quick flap for laser parts 500 x 500 mm including sensor for part chute - Liftable laser cutting support - Slug detection TRUMPF Laser - Laser TruFlow 2700 with LensLine and optimized standby mode - High-frequency excitation - Cooling unit - Laser control system TASC - Enclosed beam guidance - Beam pipe ventilation with compressed air Cutting Head - Lens cutting head with 170 mm focal length - Universal cutting head quick-change device UTI with bus connection - ControlLine Programming - Extended workshop programming (TruTops via network access) Punching Station - Electro-hydraulic punching head - Rotating mono-tool holder - Tool length compensation - Programmable clamping system with manually adjustable clamping force - Stroke counter for punch - Spray lubrication for punch - Punch slug extraction - Deflection detection - Flap for punching parts 500 x 500 mm including sensor for part chute - Reaching the fill level in the punching console - Level monitoring for thread forming and tool lubrication Control System - TRUMPF control system based on Rexroth IndraMotion MTX - External control panel with 15" TFT touchscreen - Hard drive with 160 GB storage capacity - Integrated technology data - Teleservice via internet - Integrated e-shop - Programmable cutting gas pressure - Automatic shutdown - Production plan Data Transfer - Network connection RJ45 and USB interface Safety - CE marking - Dual light curtains - Monitoring system for gas pressure, temperature, coolant, among others - Quick stop - Protection against scattered radiation - Compact dust extraction system - TruFlow 4000 including LensLine - Automatic nozzle changer - MultiTool function - MultiShear function - MultiBend function - Thread forming function - Deburring and rolling technology - Active die - StripLine - Adaptive stroke calibration - Spray lubrication for die - 4 individually opening clamping claws - Repositioning cylinder - Vibration-damped mounting - Chip conveyor with tipping container - Brush tables with loading and unloading assistance - Blowing device for small parts Automation: SheetMaster - Suction frame 3000 x 1500 mm with 36 suction cups (y-axis = 400 mm) - Adjustable suction rails (v-axis = 120 mm) - Peeling suction - Vacuum sensor for each suction cup - Sheet thickness sensor for double sheet detection - Automatic clamping claw closing on machine - Central lubrication - Main-time parallel loading and unloading of SheetMaster - Unloading monitoring GripMaster special arrangement 4m: - Scrap grid tongs with sensor - Scissor lift table 400 mm Kdodpfxoza A Hlo Abven

Condition: used, PRIMO - 1100 for sale Ksdpfx Ajzb Eprsbvjdn CONSTANT-TABLE GRINDING MACHINE with automatic head positioning Wide-belt calibrating and fine-finishing machine Combined unit with contact roller and sanding pad, featuring an electronically controlled segmented grinding shoe Belt drive motor power: 9 kW Contact roller pressure adjustable in infinitely variable steps according to grit scale Infeed table with roller support Working width: 1100 mm Feed rate: 3 - 15 m/min, infinitely variable Belt speed: infinitely variable Automatic workpiece thickness adjustment ENORMATIC quick adjustment Swiss-made quality product from a traditional workshop First delivery: 2003 Machine is WORKSHOP OVERHAULED and in TOP CONDITION Available from stock in Lieboch

Condition: used, SCM Sandya 600 RCS 110 Wide-Belt Calibrating and Fine Sanding Machine The advanced sanding center for calibration, solid wood sanding, and fine veneer sanding TOP Equipment 1. Calibration sanding unit with RA diagonally ribbed steel contact roller 2. Combination sanding unit with 140 mm diameter contact roller, 85 Shore hardness, elastic segmented sanding shoe with electronically controlled sectors Working width 1100 mm Main motor power 15 kW Design "B" for RCS MESAR elastic segmented sanding shoe electronic programming unit "LOGIC SC screen control" Kodpszb Dvwsfx Abvodn electronic adjustment of working height with automatic workpiece detection Roller table in infeed and outfeed for long workpieces Machine from small craft business / LEASE RETURN First delivery 2017 ex stock Lieboch / LEASING OPTION

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,000 kg, maximum load weight: 15,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,040 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 1 pair of removable guide rollers, additional 4 container locks with sturdy 20"-based arms for swap bodies 7.15 and 7.45 Swivel frame with heavy-duty ball bearing swivel ring Wheel chocks with holder Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Rear mud flaps across the entire width (not compatible with forklift mount) Quarter-shell front fenders and half-shell rear fenders Kdjdpfx Aezd Uvlsbven *Towing equipment for trailer turntable Towing fork with certified 40 mm tow eye Towing fork mechanically adjustable in length by approx. 6 x 100 mm (approx. 1900–2500 mm); towing fork length set to 2200 mm *Axles + Suspension BPW or SAF drum brake axles, at the manufacturer’s discretion “Laser-aligned axles/chassis” to reduce tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded piping for easy maintenance. Air reservoir: 180 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, EBS, Electronic Brake System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With raise/lower valve, hold function in both lower and raise positions Axle load detection via EBS CAN bus signal, for display in the cab; the truck must be equipped accordingly; no truck installation (no calibrated scale) Tire pressure monitoring system *Wheels and tires 235/75 R17.5, brand selected by the manufacturer Steel rims in twin configuration, factory silver *Electrical System 24 volts, Aspöck Eco LED II multi-chamber lights, yellow LED side lighting linked to the turn signals (“flashing side lights”), LED license plate lighting, (Note: With certain towing vehicles, false diagnostics may occur even though the system is functioning properly) 2 white LED front position lights 2 white/red rear lane-keeping lights (LED) 2 x 7-pin reverse-polarity-protected connectors at the front, with connecting cable, LED work lights on both sides (activated by the reverse light) 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the crossbars, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holders Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint Finish Frame hot-dip galvanized or painted according to customer preference

Condition: excellent (used), CATALOG NO. 7967 TECHNICAL DATA - Maximum working width: 1100 mm - Maximum working height: 170 mm 2 units: 1) Grooved metal roller for calibration 2) Grooved rubber roller + shoe + metal roller – Top side: - Rubber pressure roller - Unit (two units on one motor) 15 kW - Rubber pressure roller - Outfeed rubber roller - Belt cleaning by air blast – Bottom side: - 2 metal pressure rollers - Feed belt - 2 rubber pressure rollers - Pneumatic belt oscillation - Grinding thickness potentiometer - Electric and manual table lifting (for precise adjustment) - Pneumatic brake - 2 feed speed options - Working pressure: 6–8 bar - Extraction nozzle diameter: 2x140 mm - Overall dimensions (L/W/H): 1830x1670x1950 mm - Weight: 1160 kg ADVANTAGES – Italian manufacture – 2 sanding units – Not repainted – Used sander, perfect condition Kjdpoza Elwofx Abvsdn Net price: 77,900 PLN Net price: 18,550 EUR (based on 4.2 EUR exchange rate) (Prices may vary with larger exchange rate fluctuations)

Condition: used, This listing is for the Watson-Marlow 520Di Dispensing Pump without legs The unit is in full working condition and is ready for immediate use Overview The 520Di is a high-precision, programmable peristaltic dispensing pump designed for aseptic fluid transfer and filling in pharmaceutical, biotech, and food processing environments. With a simple keypad-screen interface and up to 50 programmable batch routines, it meets cGMP documentation needs while delivering fast and accurate fluid dispensing. Dispenses 50 mL in 2 seconds with ±0.5% accuracy Pumps up to 3.5 L/min, pressures up to 2 bar Batch record output for regulatory compliance 5-year warranty Enclosure options: IP31 (NEMA2) and IP66 (NEMA4X) Control User Interface: Tactile membrane keypad + alphanumeric LCD Security: Optional passcodes to lock settings Program Storage: Save 50 custom fill/dispense sequences Digital I/O: 4 configurable outputs Remote Operation: Contact closure or logic input control Documentation Full operating manuals Kdodpfx Abexv Da Revon Validation support documents (cGMP, IQ/OQ protocols) Maintenance and calibration guides Sectors & Applications Pharmaceutical & Biotech: Aseptic fill/finish, cell culture media filling, vial/bottle dosing Food Production: Adding dyes, vitamins, flavours Laboratory R&D: Benchtop reagent prep, Petri dish filling Chemical Processing: Metering corrosive or high-viscosity fluids

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,200 kg, maximum load weight: 16,800 kg, overall weight: 21,000 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, total length: 7,200 mm, total width: 2,550 mm, total height: 1,800 mm, suspension: air, tire size: 435/50 R19,5", tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. Chassis, central axle, tipping trailer Steel welded construction, continuous tipping shaft at the rear with 100 mm ball bearing Type 210, then total weight technically 21,000 kg (special permit required) Gearbox support leg at the front Retractable rear support 2 chocks with holder Under-ride guard, steel Splash guards at the rear over the entire width (not in conjunction with forklift holder) Quarter panel fenders in front of and behind each axle 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable 1 pair of aluminum ramps, 3,440 mm long, 360 mm wide, load capacity per pair 8,000 kg (attachment rail for ramps at the rear) Coupling device for central axle trailer Drawbar with tested 50 mm tow hitch Axles + suspension BPW disc brake axles "Axle/chassis laser-aligned" reduces tire wear and fuel consumption Axle spacing 1810 mm (then 10 tons axle load technically) Air suspension Braking system 2-line compressed air brake system Color-coded line routing for easy maintenance. Spring brake parking brake 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit, 24 Volt EBS, electronic braking system with EBS connector at the front, with connection cable, Note: The trailer may only be towed by tractor units that guarantee the effectiveness of the ABS! with lift and lower valve Vehicle - driving stability system Axle load detection via EBS-CAN bus signal, for display on the display in the driver's cab, truck must be correspondingly pre-equipped, no truck installation (no calibrated scale) Wheels and tires 435/50 R19.5", manufacturer's choice Tires with 164 K or J marking, manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front in LED 2 white/red marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connection cable, 1 additional LED work light at the rear, switched via reversing light Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with stroke limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If required, this can be retrofitted to the truck. (Truck with max. hydraulic delivery rate of 55 l/min) Operation hydraulically via truck PTO Hydraulic connection with SVK plug NW 10/3, incl. connection hose Tipping bridges Steel sheet floor Hardox 450, 4 mm thick, ball bearing at the rear, 100 mm diameter Side panel construction steel, side walls foldable and pivotally mounted with central locking at the bottom. Rear wall pivotable and as a 2-wing door (not foldable), with door holder and protective rubber on the side (not in conjunction with pivot or mesh grating attachment) Side wall retraction springs (not possible with foldable front wall) Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Painting Side panels/bridge painted in desired color Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. Kjdpfxszd Eyno Abvsdn

Condition: used, This listing is for Akta Process sample pump. The unit is in full working condition and ready for immediate use. High-performance liquid chromatography sample automation pump optimized for scaling up biopharmaceutical manufacturing and reliable laboratory fluid delivery. [[1](?selectedProduct=28956095), [2](), [3]()] Transparency Report and Technical Audit: • Source Pedigree: Biotech / Research Facility • Condition: Direct-from-Bench (Decontaminated/Original) • Power-On Test: Verified; Digital display active, lighting operational, and fan system engaged. Kjdsxhga Ropfx Abvedn • Integrity: 100% Original Parts (Non-Refurbished) [[1](), [2]()] Software and Media Disclosure: As a Direct-from-Lab asset, any original software media or accessories found with the unit are included as a courtesy. Licensing Notice: We do not provide, transfer, or guarantee software licenses or keys. The buyer is responsible for all software licensing, registration, and workstation compatibility via the manufacturer. Notice for Procurement: This unit is sold As-Is. While we verify the power-on status and physical integrity, we do not perform analytical validation, fluidic testing, or operational calibration. Ideal for labs with in-house technical expertise or existing service agreements. [[1](), [2]()] Sustainability Impact: By choosing Direct Reuse, your facility avoids the carbon footprint of new manufacturing and prevents specialized materials from entering waste streams. Direct-to-Lab reuse is the most carbon-efficient way to equip a modern laboratory • Condition: Direct-from-Bench (Decontaminated/Original) • Source Pedigree: Biotech / Research Facility

Condition: good (used), Year of construction: 1990, functionality: fully functional, total height: 100 mm, total width: 630 mm, total length: 1,000 mm, overall weight: 189 kg, plate height: 100 mm, Granite measuring plate / inspection plate DIN 876 quality 0 – 1000 x 630 x 100 mm incl. base frame Kodpjzd Rl Aofx Abvsdn For sale is a high-quality granite measuring plate (hard stone test plate) according to DIN 876, quality class 0. Suitable for precision measurements, mechanical engineering, toolmaking, quality assurance, or demanding workshop applications. Technical data: Dimensions: 1000 x 630 x 100 mm Material: Hard stone / granite Accuracy class: DIN 876 quality 0 Weight: approx. 189 kg Flatness according to test report: 2.9 µm Target value: 8 µm Last documented inspection: 06.05.2013 Includes a sturdy steel base frame with leveling feet Used very little Exact year of manufacture unknown, manufacturer unknown Condition: The measuring surface is in good used condition. No visible damage or chipping on the surface. Signs of age and use are present on the frame. Inspection labels are present. Special features: Precision measuring and inspection plate for the highest requirements Low-vibration hard stone Industrial quality Ready for immediate use Includes base frame Pickup & Shipping: Pickup preferred. Assistance with loading using a forklift or crane is readily available. Shipping via freight carrier is also possible, with the buyer covering all costs. Price: Negotiable 650 net plus VAT. No guarantee, warranty, or return. If you have any questions or need more information, please send us a message or call us. Keywords: Granite measuring plate, measuring plate, hard stone plate, hard stone test plate, precision measuring plate, precision plate, inspection plate, test plate, layout plate, measuring table, metrology, quality assurance, toolmaking, mold making, mechanical engineering, precision engineering, DIN 876, quality 0, calibration plate, reference surface, straight edge, measuring room, measuring instruments, granite plate, surface plate.

Condition: refurbished (used), functionality: fully functional, Year of construction: 2007, DAVI_MCB 3060 WT 4-roll plate bending machine CNC _ 3000x65 MM - Year of make 2007 Capacity plate width 3100 mm Plate thickness 65 mm Prebend 55 mm TOP ROLL 600 MM LOWER ROLL 550 MM Configuration installed: • Surface hardening of the four rolls • Dual pre-pinch, with adjustable force upon the input of plate thickness • Conical bending hydraulic attachment - hardened contrast pad. • Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. • Calibration system for re-rolling of welded shells rounding. • Console electric independent with centralized commands joysticks and CNC screen readout. • CNC controller DAVI GENIUS semiautomatic and fully automatic programmable. with digital readout of the 4rollers for use in manual operation, • Opening front side hydraulic drop-end to unload closed shells. • Variable working speed step-less axis interpolation. • Safety installation with emergency stop. • Instruction manuals for operation and service Voltage electric 3phase Vac 380/50 power Kw 75 Kedpfx Absy D Npiovjdn nr.1 top support hydraulic operated , shell ID max 5 mtrs - CNC programmable nr.1 side support hydraulic on the left nr.1 side support hydraulic on the right, finger pusher to swing the sheet plate forming cones rolling.

Condition: excellent (used), functionality: fully functional, Year of construction: 2017, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: MG EVO, controller model: 4axis autocalc, number of rollers: 4, roller (bottom) diameter: 240 mm, roller (top) diameter: 250 mm, side roll diameter: 180 mm, roller diameter: 300 mm, roller length: 4,100 mm, working width: 4,000 mm, working height: 800 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 4 mm, power: 5 kW (6.80 HP), input voltage: 400 V, number of digital displays: 4, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, model capacity 4000x6 mm CNC EVO plate roll Hydraulic 4 roll plate bending machine used year 2017 plate thickness rolling 6 mm pre-bend 4 mm minimum rolling diameter ID 300 mm plate max width on the rollers 4100 mm top roll size 250 mm lower roll 240 mm side rolls 180 mm Power on hydraulic unit 5,5 kw Vac 400/50 -480/60 Installed configuration Hardened rolls high surface strength Conical plate rolling, cone bending Electric console remoted with CNC EVO 4 axis Automatic plate roll programmable on drawing import from CAD station Rolling compensation upon plate different yield strength data input Hydraulic rotation central rolls driven Parallelism of the 4 rollers lifetime with torsion bar Kdedpey I Sp Tsfx Abven Pre-pinch setting upon plate real strength for best pre-bend Drop-end open front for unloading closed shells Re-rolling system for welded shells precise calibration. Safety and emergency stop installed Manuals and schematics service and instruction books

Condition: good (used), functionality: fully functional, Year of construction: 1998, control type: NC control, degree of automation: semi-automatic, actuation type: hydraulic, controller manufacturer: Siemens, controller model: Simatic OP7, number of rollers: 4, roller (bottom) diameter: 470 mm, roller (top) diameter: 530 mm, side roll diameter: 400 mm, roller diameter: 530 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 2,000 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 65 mm, sheet thickness stainless steel (max.): 50 mm, overall weight: 40,000 kg, total length: 6,000 mm, total width: 2,900 mm, total height: 2,900 mm, power: 55 kW (74.78 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 4, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, plate bending roll capacity 3000x50 mm Davi modelMCB3053 Hydraulic 4 roll plate bending machine, year 1998 plate width 3000 mm thickness rolling 50 mm pre-bending 40 mm width on the rolls 3100 mm upper roll size 530 mm lower roll 470 mm side rolls 400 mm Power electric 70Hp on hydraulic unit voltage 380/50 - Installed configuration Hardened surface of the 4 rolls conical bending attachment – hardened cone bending Console electric with digital position readout of the rolls Controller Siemens Simatic OP7 NC programmer for automatic rolling Hydraulic power driven the central rolls with axial gearbox Pre-pinch pressure adjustable plate edge pre-bend. Drop-end open front for unloading closed shells Rerolling system for calibration roundness of welded shells. Safety and emergency system installed. Ksdpfoy D Ngzsx Abvjdn Manuals original for operation and maintenance Dimension 6000x2900 x h 2900 mm weight 40000 kg

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: EVO, controller model: EVO 4 AXIS 15", number of rollers: 4, roller (top) diameter: 300 mm, roller diameter: 300 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 1,250 mm, sheet thickness (max.): 30 mm, sheet thickness steel (max.): 30 mm, sheet thickness stainless steel (max.): 25 mm, overall weight: 17,000 kg, total length: 5,500 mm, total width: 2,000 mm, total height: 2,100 mm, power: 18.5 kW (25.15 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, 4roll hydraulic plate bending machine rated capacity 3000x35 mm MODEL MG M3035 , used year 2024 machine as new with warranty included Planetary dual pre-pinch Performance Capacity: Plate width 3000 mm plate thickness rolling 30 mm pre-bend 25 mm minimum rolling diameter ID 350 mm max open width plate feed 3100 mm special top roll reduced size 300 mm to achieve rolling ID 350 mm Power electric motor 18.5kw on hydraulic unit Vac 400/50 -480/60 Installed configuration Hardened rolls high surface strength Conical plate rolling, cone bending Electric console remoted on wheels with joysticks and readout CNC programmable 4 axis controller touch screen 15” Setup virtual infinite rolling programs with teach-in mode and cad/cam operator interface --- Hydraulic motorized driven the central rolls Pre-pinch load adjustable for pre-bend Drop-end top roll front open unloading closed shells Re-rolling system for welded shells calibration. Safety and emergency stop Manuals and schematics machine dimension 5500x2000x2100 mm -weight 17ton Kdedpfx Ajy Tbf Iebvjn --- Additional accessories available with the machine See layout drawing in enclosed nr.1 central support hydraulic 2.2 ton capacity to support large shell dia up to 4,5 meters id nr.1 side support hydraulic left side 2.2 ton double arm nr. 1 side support hydraulic right side 2.2ton double arm

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 7,500 kg, maximum load weight: 18,700 kg, overall weight: 26,200 kg, axle configuration: 2 axles, total length: 12,400 mm, total width: 2,550 mm, tire size: 205 / 65 r 17,5, Further information Chassis semitrailer forwarding Welded fine-grained steel construction, fifth wheel plate with replaceable 2 kingpins, rear bevel to approx. 1920 mm, suspension bar for ramps at the rear and front on gooseneck, grinding rollers at the rear, drop center after cranking up to the axle unit. Drawing approval required from customer in case of order! Pair of lashing lugs at the top and side of the outer frame, 10 tons each Pair of lashing eyes embedded in the outer frame on gooseneck, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Folding rear support, mounted on the outside Wheel chocks with holder Aluminum side collision protection Steel underride guard for EG, if technically possible Quarter-shell mudguards with anti-spray flaps according to EG Kdedpfx Asi Ri Hrebvon 1 pair of wheel recesses after gooseneck recessed in the low bed of the tramline area, sloping towards the entrance. Length at bottom approx. 1840 mm, depth of wheel recesses approx. 200 mm. 2nd pair of wheel recesses on rear slope. Depth approx. 200 mm. Note! Frame in main beam area 200 mm higher than wheel recess. In the event of an order, a precise technical inspection is still required. Wheel recess cover can be pulled out from the drop deck with hardwood inserts, on rear slope with hardwood inserts. Electric cable winch, 24 volt, pulling force 5500 kg, mounted in the offset gooseneck, not reaching into the loading area, operation with radio remote control, operation with radio remote control, cable length 35 m x approx. 10 mm, with roller cable window and removable guide roller on rear slope. Axles + suspension SAF or BPW drum brake axles of our choice Air suspension with lift & lower valve + auto-reset function Wheels and tires 205 / 65 R 17.5 tires with 129/127K (132/132G) marking for 8 to tire load capacity at max. 90 km/h at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS make Haldex, electronic brake system with EBS socket at the front, without connecting cable (sent to the customer for approval brake calculation.15.07.2021) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection via EBS-Canbus signal, for display via display in the cab, truck must be prepared accordingly, no truck instal. (no calibrated scales) Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Floor Gooseneck with steel / checker plate covering 30 mm screen-printed floor, in the drop floor between the longitudinal beams in the middleIn the tramline area covered with toothed grating in the wheel recesses with steel/checker plate covering. Access ramps Pair of aluminum ramps 3,200 mm long, load capacity per pair 12,000 kg Pair of steel ramps for entering the drop deck Pair of steel ramps for crossing on gooseneck Drop sides Approval / plates Country of approval: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Prepared for single-line license plate holder Contour markings with reflective strips to ECE R 048, yellow at the sides and red at the rear Warning sign according to ECE -

Condition: new, functionality: fully functional, Year of construction: 2025, operating hours: 0 h, machine/vehicle number: plate roll, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: MG EVO, controller model: EVO 4 AXIS, number of rollers: 4, roller (bottom) diameter: 140 mm, roller (top) diameter: 160 mm, side roll diameter: 150 mm, roller diameter: 200 mm, roller length: 2,050 mm, working width: 2,000 mm, working height: 700 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 6 mm, overall weight: 2,200 kg, total length: 3,200 mm, total width: 1,100 mm, total height: 1,200 mm, power: 4 kW (5.44 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 4 ROLL BRAND MG ITALY, HYDRAULIC MODEL M2006P EVO_CNC PLATE BENDING ROLL PLANETARY DESIGN DOUBLE PINCH PRE-BENDING CNC_EVO PROGRAMMABLE AUTOCALCULATION AUTOMATIC PLATE ROLLING Capacity: -Width of plate: 2000 mm -Thickness of plate rolling 6 mm -Thickness of plate pre-bending 4 mm Ksdsw Dnd Sopfx Abvjdn Rolls -useful width mm. 2050 -Top roll mm. 160 - Lower roll mm. 140 Configuration installed: • Surface hardening of the four rolls, smooth finishing suitable for stainless plates rolling • Dual pre-pinch, with adjustable force upon the input of plate thickness • Conical bending hydraulic attachment - hardened contrast pad. • Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. • Calibration system for re-rolling of welded shells rounding. • Console electric independent with centralized commands joysticks and CNC screen readout. • CNC controller on touch screen 15” , CAD/CAM interface 4 axis auto calculation software package. with digital readout of the axis for use in manual rolling, semiautomatic and fully automatic programmable. • Opening front side hydraulic drop-end to unload closed shells. • Variable working speed step-less axis interpolation. • Safety installation with emergency stop. • Instruction manuals for operation and service.

Condition: like new (used), functionality: fully functional, Year of construction: 2025, machine/vehicle number: M3022, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: Delsy, controller model: Digital readout, number of rollers: 4, roller (bottom) diameter: 330 mm, roller (top) diameter: 350 mm, side roll diameter: 260 mm, roller diameter: 400 mm, roller length: 3,000 mm, working width: 3,100 mm, working height: 900 mm, sheet thickness (max.): 22 mm, sheet thickness steel (max.): 22 mm, sheet thickness stainless steel (max.): 22 mm, sheet thickness aluminum (max.): 30 mm, overall weight: 13,000 kg, power: 10 kW (13.60 HP), input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, hardened rollers, swiveling upper roller, Bending capacity with dual Initial pinch planetary plate width 3000 mm thickness 22 mm pre-bend 18 mm --- Length on the rolls 3100 mm top roll 350 mm lower roll 330 mm Power electric 20Hp Vac 400/50 Installed configuration Hardened surface of the 4 rolls Driven central rolls rotation hydraulic motorized with gear units Synchronized hydraulic rotation between the rolls Rolls parallelism lifetime set with torsion bar Conical plate bend hydraulic attachment Calibration re-rolling feature for welded shells Front open drop-end to unload the closed rolled plates. Control console electric commands with digital readout Kdsdpfxoid Al Ne Abvon Safety and emergency systems installed Manuals and schematics originals

Condition: like new (used), functionality: fully functional, Year of construction: 2024, machine/vehicle number: 4ROLL 3000X 15 MM, roller (bottom) diameter: 270 mm, roller (top) diameter: 290 mm, side roll diameter: 250 mm, roller diameter: 310 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 800 mm, sheet thickness (max.): 15 mm, sheet thickness steel (max.): 15 mm, sheet thickness aluminum (max.): 20 mm, sheet thickness copper (max.): 25 mm, overall weight: 8,500 kg, total length: 5,100 mm, total width: 1,500 mm, total height: 1,800 mm, power: 7.35 kW (9.99 HP), number of digital displays: 2, warranty duration: 12 months, cone diameter: 400 mm, working length: 3,000 mm, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, 4 ROLL DUAL PRE-PINCH ROLLING MACHINE NEW -Width of plate 3000 mm -Thickness of plate rolling 15 mm -Thickness of plate pre-bend 12 mm minimum bending diameter ID 350 mm Rolls dimensions: -Surface length mm. 3100 Kdjdpfxswfc S Ts Abvjn -Top roll mm. 290 -pinch roll mm. 270 -Power electric 10 Hp Technical data: -rolls hardened surface high resistance -variable rolling speed -Powered driven hydraulic rolls rotation -conical bending attachment roller type -calibration system re-rolling welded shells -deflection pinch pressure adjustable upon the thickness -overload protect complete safe operation of the machine. -control console on wheels with electric joysticks commands -position readout digital display for rolling memorize and repeat

Year of construction: 2016, condition: ready for operation (used), - USED - TRAVELLING COLUMN MILLING MACHINE LONGITUDINAL TRAVEL: 6000 mm TRANSVERSAL TRAVEL: 1500 mm VERTICAL TRAVEL: 2500 mm Kodpex Ru Azsfx Abvedn RAPID FEEDS L-T-V: 35 m/min SPINDLE: 337- 5000 rpm; 42 kW; 1180 Nm WORKTABLE: 300 x 2500 x 7000 mm HEAD: ISO 50 ; MILLESIMAL POSITIONING ; A/B AXIS AUTOMATIC TOOL MAGAZINE: PICK-UP ; 12 POS CONTROL UNIT: HEIDENHAIN TNC 640 HIGH PRESSURE COOLANT: 20 Bar NOTE: AUTOMATIC HEAD CHANGE; COMPRESSED AIR INSIDE THE TOOL; RTCP; AUTOCAL SOFTWARE FOR AUTOMATIC CALIBRATION