Used Holzher 1401 for sale (161)

Condition: not inspected (used), Used machine Dksdjxviuaspfx Ah Ujw Used vertical panel saw by Holz-Her, type 1210 Older model; suitable only for coarse cutting Technical data: Cutting length approx. 5300 mm Cutting height approx. 2200 mm Cutting depth approx. 80 mm Maximum saw blade diameter 300 mm Motor power 4 kW Location: ex stock 54634 Bitburg - immediately available -

Year of construction: 2015, condition: used, Used machine Year of manufacture: 2015 Info: Was a demonstration unit from Holz-Her and only went into production operation in 2019 Dkodpfxewkbags Ah Uew Equipment and technical data: Automatic Panel Storage System STORE-MASTER 5110: - 30% to 50% space saving - Minimal distances between stacks (from 70 mm) = optimal space utilization - No panel damage; panel separation monitored by weight measurement - Fully automatic process (infeed/outfeed) as well as automatic loading of the machine - Adaptable to all panel formats (1.2 to 5.6 m), depending on option - Panel rotation by 90° - Low height of manipulator construction External dimensions: - Length: 8.5 m - Width: 7.5 m Panel formats: - Min. panel size: 1.2 x 0.6 m - Max. panel size: 3.2 x 2.1 m - Max. lifting weight: 150 kg Lifting and stacking range: - Stack height: 1.8 m (max. 2.0 m) - Max. lifting height: 2.1 m Travel speed: - Horizontal: approx. 120 m/min - Vertical: approx. 45 m/min Manipulator suitable for slightly air-permeable, smooth materials such as coated chipboard, blockboard, raw MDF, raw HDF, raw chipboard (good quality) Vacuum capacity for the suction units on the manipulator: 100 m³/h for a material mix in the warehouse including e.g. MDF and raw chipboard Connected load: 6 kW Portal bridge with vibration damping, manipulator head with lifting device, as well as steel gripper arm, space-saving due to low structural design Articulated arm design with direct drive via steel band; thus maintenance-free and insensitive to vibration Electronic panel position measurement Panel rotation correction Panels are measured using sensors and neatly stacked Separation device for thin panels via integrated weight measurement Infeed and outfeed station Direct loading onto the machine Warehouse management software Previous list price: €110,000.00 Availability: short-term Location: Flörsheim

Condition: used, Holz Her STREAMER 1054 FÜ + PU Edge thickness 0.4 - 6 mm Modern control with selector switch for adjusting the units Pre-milling unit for attaching before the gluing part Fully automatic edge magazine for rolls and strips Glue application station GLU-JET cartridges + PU gluing Glue application using nozzle technology Workpiece height 6-60 mm Automatic glue height adjustment High-quality 3-roller printing unit, 1st roller motorized Cutting unit pneumatic. for rolls and strips up to 6 mm edge thickness with pneumatic adjustment of 0-10° bevel of the mitre saws pneumatic milling unit, flush milling 6 mm, radius milling - chamfer milling - 15°, pneumatic via control panel scraper unit for chamfers and radii with 2 scraper holders pneumatic engagement and disengagement surface scraper unit - finish spraying device - PU machine is WORKSHOP REFURBISHED in TOP CONDITION Dksdpfx Ahjxu E Nwj Ujw

Condition: used, Year of construction: 2004, Cutting length 4300 mm, cutting height 2200 mm, motor 4.0 kW, cutting depth 60 mm, saw blade diameter 250 mm. Location: Nattheim. Dkodpfxoxr A Nvs Ah Usw

Condition: good (used), Year of construction: 2013, Cartridge system (for rolls and strip material) Reinforced cutting cylinder Dsdpfsxqy Elsx Ah Uekw Cutting unit Multi-function milling station (chamfer-flush-radius) Pull scraper Edge thickness 0.3–3 mm External dimensions L x W x H approx. 3060 x 1040 + magazine plate overhang) x 1350 mm All information without guarantee; data obtained from a brochure.

Condition: used, Year of construction: 2003, total height: 2,900 mm, total length: 5,100 mm, total width: 1,700 mm, Weight: 650 kg - Year: 2003 - Documentation available: No - Serial number: 633/0-306 - Max. cutting height vertical [mm]: 2200 - Max. cutting width [mm]: 4300 - Min. saw blade diameter [mm]: 240 - Max. saw blade diameter [mm]: 250 Dedoxbhmlopfx Ah Uskw - Arbor saw blade diameter [mm]: 30 - Horizontal cutting: Yes - Vertical cutting: Yes - Transport dimensions: 5100mm x 1700mm x 2900mm (l x w x h) - Transport weight [kg]: 650kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2007, Used machine Year of manufacture: 2007 Equipment and technical data: Nesting system with grid table Processing dimensions: - X: 5000 mm - Y: 1240 mm - Z: 135 mm Traverse paths: - X: 5665 mm - Y: 1650 mm - Z: 325 mm with milling unit 7933: - Motor 11 kW (S6) - HSK 63 - water-cooled with C-axis with 18-position disc tool changer with vacuum pump 250 m³ with handheld control device with central lubrication Dkedpfxewka Ipe Ah Usw with minimum quantity lubrication system Availability: short-term Location: Röllbach

Condition: used, Holz Her Perfect 1422 K + PU Heavy-duty version, for edge banding up to 20 mm thickness Fully automatic roller magazine – crosscut shear Fully automatic edge magazine for strip material Cartridge + PU gluing station Flush trimming Dkjdsxurqbjpfx Ah Uew Multifunction milling unit, flush – chamfer – radius milling with mechanical digital adjustment Soundproof enclosure CE-compliant design Machine is FUNCTIONALLY TESTED and in VERY GOOD CONDITION available ex-stock Lieboch

Condition: used, Year of construction: 1994, Edge thickness 0.3 - 20 mm, edgeband height: max. 66 mm, edgeband length: min. 200 mm, workpiece width min. 60 mm, workpiece length min. 140 mm, workpiece thickness: min. 6 mm, max. 60 mm, feed speed 8 or 16 m/min - Edgebanding with Ultra - Granupress - End trimming with 2 saws, 0 - 15° tiltable - Milling, radius / flush - Corner copying - Scraper - Pneumatic buffing Location: Nattheim Dksdpfxovvkdts Ah Uew

Condition: good (used), Year of construction: 1999, Cutting area approx. 4300 x 2100 mm manual feed automatic retractable grid Cutting depth 40 mm Motor 3 kW Saw blade diameter 220 mm TRK extraction Dedexp Uyuopfx Ah Uskw Further technical data on request All information provided without guarantee

Condition: used, Year of construction: 2003, Used machine Year of manufacture: 2003 Features and technical data: - Control system with LCD display - Swiveling operator panel - Program memory - Manual pressure bridge adjustment - Feed via transport chain - Extendable workpiece support Jointing unit 1961: - 2 x 2.0 kW - Diamond jointing cutters for up-cut and down-cut operation Edge magazine 1903: - Support plate 820 mm, max. loading capacity 40 mm - Automatic feeding of coil and strip material Adhesive application system 1906: - Cartridge system with sensor-controlled nozzle - Automatic reloading Dsdpfowka Nyex Ah Ujkw - Use of PUR adhesives possible Pressure unit 1816: - With powered roller - Pneumatic control of the pressure unit End trimming unit 1918: - 2 x 0.22 kW - Swivels from 0 to 10°, pneumatically adjustable Milling unit 1942 MOT 2: - For flush, radius, and chamfer milling - Motorized adjustment - Air nozzle at milling unit Corner copying unit 1832: - Corner copying up to r = 3 mm, postforming up to r = 6 mm Radius scraper unit 1929 MOT 2: - For plastic edging up to 3 mm - Chip collection box for radius scraper Surface scraper 1964: - Process-controlled surface scraper - Air nozzle at surface scraper Buffing unit 1940 Edge thickness, coil material: 3 mm Edge thickness, strip material: 5 mm Max. edge thickness, corner copying: 3 mm Workpiece thickness: 6-45 mm Workpiece thickness, corner copying: 45 mm Min. workpiece length: 180 mm Feed speed: 8 m/min Distance, workpiece support: 470 mm Support plate diameter for edge material: 800 mm End trimming blade for coil material up to: 3 mm Heating up time: 3.5 min Jointing cutter power: 2 x 2 kW End saw power: 2 x 0.22 kW Milling station power: 2 x 0.6 kW Corner copying power: 0.22 kW Extraction nozzle jointing unit: 120 mm Extraction nozzle milling unit: 70 mm Extraction nozzle scraper unit: 70 mm Dimensions: 5,350 x 1,669 x 1,940 mm Weight: 1,200 kg Location: Röllbach Availability: short notice

Condition: used, Holz Her Sprint 1317-1 FÜ + PU heavy-duty design – edge thickness 0.4 – 5 mm SPS screen control large LCD display pre-milling unit before gluing area fully automatic edge magazine for coil and strip material glue application station for cartridges + PU gluing maximum edge height 51 mm automatic glue height adjustment press unit 1913, motorized pneumatic trimming unit for coils and strips with pneumatic adjustment for miter saw angle from 0–10° multifunctional milling unit 1942 MOT 2 milling unit with motorized adjustment axes for various radii – chamfering – flush milling via SPS copy milling unit 1832 for corner copying up to R 3 mm + postforming up to R 6 mm scraping unit for chamfers and radii pneumatic infeed and outfeed finish – surface scraper regular maintenance by Holz Her Dodpfxoxuhpaj Ah Ujkw machine is FACTORY SERVICED, in EXCELLENT CONDITION available from stock in Lieboch

Condition: used, Year of construction: 2009, HOLZ-HER edge banding machine CONTRIGA 1366 Edge thickness: 0.4-30 mm (depending on equipment) Edge height: 51/66 mm (depending on equipment) Panel thickness: 6-45/60 mm (depending on equipment) Edge types: Rolls and strips Feed speeds: Continuous feed from 12-30 m/min (depending on equipment) With adjustable infeed level in the magazine area (max. adjustment range 30 mm) With height-adjustable magazine plate for changing the lower edge overhang With large magazine plate Ø 820 mm for edge rolls up to Ø 800 mm With transport chain including automatic central lubrication With motor-driven, position-controlled bridge height adjustment With pneumatic locking roller for the shortest workpiece sequence With extendable workpiece support (extension width 1600 mm) With space-saving, pneumatically controlled sliding hoods over the entire machine (Deviations for individual units are possible) with motorized infeed guide with injection oiler for lubricating all joints and bolts (including operating hours counter) with central connection for extraction (2x Ø 200 mm) with integrated chip collection box at the end of the machine (when radius scraper unit is installed) PPC 231 control system - Power PC for efficient setup and changeover - 15" SVGA screen with touchscreen - 128 MB CF memory card - USB connector on board - Ethernet network connection - Keyboard connector on board - Windows-like user interface - all information in plain text and/or graphics - Rotatable and pivoting control panel at eye level - Dust-proof membrane keyboard with softkeys (pushbuttons) - LED display for unit preselection - Program list with program names and numbers - Extensive program memory - Individual selection of the units with the functions as basic setting options for setpoints, route points and tool corrections as well as the fixed route points - Centralized and clear setup processes for units and their axis settings via fine adjustment (depending on the equipment) - Interval display for the shortest workpiece distance - Integrated path control - Path points are controlled generally or program-specifically - Clear and complete recording of all operating data - Service messages in plain text - Diagnostic system - including integrated synchronous bus system for high precision in unit control - Individual administration for up to ten users, including password protection - Online maintenance (optional), data exchange with HOLZ-HER Service - Barcode interface (optional) BASIC MACHINE CONTRIGA 1366 - Belt bridge Options and accessories for the basic machine Spraying device 1856 for the inlet and outlet area For the inlet area: Electronically controlled release agent sprayer with Riepe-LPZ/II release agent For the outlet area: Electronically controlled cleaning agent sprayer with Riepe-LP163/93 cleaning agent (only in conjunction with pre-milling unit 1961 and surface scraper 1964) Joint milling unit Joint milling station 1803 (2x 2.6 kW, 200 Hz, 12000 min-1) With two plunge-controlled milling units 1 unit in up-cutting direction 1 unit in down-cutting direction Plunge path 5 mm With static frequency converter 200 Hz Without milling tool With ProLock screw-in clamp for fast tool changes Tool for 1803 (workpiece height up to 60 mm) Diamond milling cutter PRO UT 2 pieces (front and rear) including protective covers Ø 100-63 - Ø 30 mm, Z = 3 + 3 + 3, 1x left-hand rotation, 1x right-hand rotation Noise-reduced milling cutter with integrated chip guide DFC technology (Leitz syst Dkedpfx Aovvkfdsh Uew

Condition: used, Year of construction: 2001, Used machine Year of manufacture: 2001 Equipment and technical data: Machine is completely workshop overhauled! Automatic horizontal and vertical positioning for absolute and incremental dimensions Digital readout for horizontal cuts PLC control with a 2-line display and plain-text error diagnosis for operation mode and fault diagnosis Infinitely variable feed speed up to 24 m/min Automatic workpiece end detection Calculator function integrated in the control panel (calculation of workpiece dimensions) Cutting length: 4300 mm Cutting height: 2200 mm Max. trimming height: 2100 mm Max. scoring height, vertical: 2100 mm Max. cutting depth: 80 mm Motor: 5.5 kW Saw blade speed: 4,500 rpm Saw blade diameter: 300 mm Air requirement: 1,200 m³/h Air velocity: 20 m/s Static negative pressure: 1,200 Pa Extraction connection: 2 x 120 mm Dimensions (L x W x H): 5,620 (plus extraction nozzle) x 1,480 x 2,948 mm Room height: 2,990 mm Compressed air connection: 6 bar Air consumption: 50 NL/min Electrical connection load: 5.7 kW Dkedpfx Ahsw Nac Aj Usw With Supercut pre-scoring unit With pneumatically swiveling saw unit With longitudinal stop for lower workpiece support With short folding rail, complete Availability: by arrangement Location: Flörsheim

Condition: used, Holz Her Auriga 1308 FÜ + PU Compact design - Edge thickness 0.4 - 8 mm PLC screen control Edge-Control PPC 221 color display Pre-milling unit for edge preparation before the gluing section Fully automatic edge magazine for both coil and strip material Gluing unit GLU JET cartridge + PU bonding - multi-system Adhesive application via nozzle technology Workpiece height 6-65 mm Automatic glue height adjustment Pressure unit 1912-3 pneumatic End trimming unit 1918 pneumatic for coil and strip material up to 8 mm edge thickness With pneumatic adjustment from 0-10° mitre for trimming saws Milling unit for flush trimming 8 mm, corner rounding, bevel trimming at 15° via control panel Profile trimming unit 1832 pneumatic, rounds corners up to 3 mm edge thickness in throughfeed Scraper unit for bevels and radii Flat scraper unit – finish Dodpsxrr Uzjfx Ah Uskw Spraying device – PU Complete set of DIA tools included Machine is WORKSHOP-REFURBISHED in TOP CONDITION Available from stock in Lieboch

Condition: used, Storage location: Nattheim Dksdpfx Aevvkrdoh Uew

Condition: used, Year of construction: 2005, Used machine Year of manufacture: 2005 Equipment and technical data: Travel paths: - X-axis: 2,685 mm - Y-axis: 1,095 mm - Z-axis: 140 mm Milling unit: - 6 kW, water-cooled - Tool holder: HSK 63 F Dkjdpewka H Esfx Ah Uew - Speed: 1,000 - 18,000 rpm Tool changer: 6-position, side-mounted Drilling head: - 9 vertical drilling spindles, 32 mm pitch - Horizontal spindle: 1+1 - Vertical spindle: 1+1 Grooving saw in X direction Control: Twin CAM 32 Vacuum pump: 100 m³/h Includes vacuum suction cups Dimensions: 5,200 x 2,843 x 1,855 mm Weight: approx. 3,500 kg Availability: by arrangement Storage location: Röllbach

Condition: used, Year of construction: 2011, Weight: approx. 4500 kg Dkjdpfx Ahsvvi R Ej Ujw Storage location: Nattheim

Condition: used, Year of construction: 2008, Used machine Year of manufacture: 2008 Edge Control control system with 18.5" touchscreen color monitor 16:9 Dedpfx Aov Sv Enjh Ujkw Swiveling operator panel, Program storage, Motorized pressure bar adjustment, Feed via transport chain, Feed speed: 8-18 m/min Extendable workpiece support, Infeed fence with motorized adjustment Jointing unit 1961, Diamond jointing cutter for climb and counter rotation, Automatic adjustment to workpiece height Edge feed 1903 Pre-trimming up to 3 x 45 mm (depending on material) Glue application system 1905 Multi-System Automatic glue height adjustment with sensor nozzle, Pressure regulator for adjusting the cartridge contact pressure, Use of PUR adhesives possible, Pressure unit 1913 MOT, First roller driven End trimming unit 1918 with pneumatic adjustment End trim saw pneumatically swiveling, Multifunction unit 1824 MOT 4 with multifunction cutter radii 1,2,3 mm Corner copying unit 1832 Corner copying up to 3 mm edge thickness Radius scraper 1929 MOT 2 With motorized adjustment of horizontal tracing rollers With pneumatic adjustment (top and bottom separate) Chip collection box for radius scraper, Surfacing scraper 1964 For removing glue residue for a clean glue line With extraction hoods Spray unit 1856 for infeed and outfeed area Buffing unit 1940 For finishing and edge polishing ----- Technical Data ----- Edge thickness roll material: 3 mm, Edge thickness strip material: 8 mm, Max edge thickness for corner copying: 3 mm, Workpiece thickness: 45 mm, Workpiece thickness for corner copying: 45 mm, Min. workpiece length: 180 mm, Feed speed: 8-18 m/min, Distance workpiece support: 470 mm, Support table diameter for edge material: 800 mm, End cut knife for coiled material up to: 3 mm, Heating time: 3.5 min, Jointing unit power: 2 x 2 kW, End trim saw power: 2 x 0.22 kW, Milling station power: 2 x 0.35 kW, Corner copying power: 0.22 kW, Extraction port jointing unit: 120 mm, Extraction port milling unit: 70 mm, Extraction port scraper unit: 70 mm, Total length: 5,350 mm, Dimensions (LxWxH): 5,350 x 1,669 x 1,940 mm Picture of operating hours taken from a recording in 2022 Availability: short term Location: Röllbach

Condition: used, Year of construction: 2006, EVA glueing, 2 pressure rollers, cross-cutting station, pre-milling cutter and rounding cutter, surface scraper, transport device Storage location: Nattheim Dksdpfjvvkg Ijx Ah Uow

Condition: used, Year of construction: 2004, Used machine Year of manufacture: 2004 Condition: Functionally tested Equipment and technical data: Travel distances: - X-axis: 2,685 mm - Y-axis: 1,095 mm - Z-axis: 140 mm Milling aggregate: - 6 kW, water-cooled - Tool holder HSK 63 F - Speed 1,000 - 18,000 rpm - Tool changer: 6-position, lateral Drilling head: - 9 vertical drilling spindles at 32 mm pitch - Horizontal drilling spindle: 1+1 - Vertical drilling spindle: 1+1 Grooving saw: in X direction Control: Twin CAM 32 Vacuum pump: 100 m³/h Including vacuum suction cups Dsdpfx Asxpla Sjh Uekw Dimensions: 5200 x 2843 x 1855 mm Weight: approx. 3,500 kg Availability: as agreed Storage location: Lower Saxony

Condition: used, Year of construction: 2009, Automatic central lubrication Milling unit 7833 2-stage, 11 kW power 1000 - 24000 rpm 1 double drilling spindle in X-direction 1 integrated sawing unit for sawing / grooving in X-direction, traveling Tool changer 7892, 16-way Linear Pick-up changer, permanently installed on the right-hand side of the machine Laser pointer consisting of 2 laser pointers for positioning the vacuum suction cups or tracing the workpiece contour Automatic console - suction cup positioning 6 consoles including 3 suction cup holders per console including 1 vacuum suction cup 80x80 mm per suction cup holder including 4 feeding aids Additional processing fields at the front for 6 consoles Basic unit pneumatics for frame clamping system 7974 (6 consoles) 2D barcode scanner Video camera in the processing head Vacuum pump 140 m³/h Vario tool Change changing unit package consisting of Consists of: Vector axis 7899 (C-axis), fully interpolating, 0-360° continuously rotatable, including pneumatic tool changer 7890, single-slot magazine pick-up system, permanently installed in front of the machine frame on the left. Tool changer 7894, 6-slot pick-up magazine specifically for Vario Tool Change tool holders, permanently installed in the machine frame on the left, can be equipped with a Vario Grip KSJ F 40 collet chuck, 3 Vario Grip KSJ F 40 tool holders (for 2-20 mm ER32 collets), 1 saw blade holder, 3 collets according to customer selection, 1 carbide circular saw blade, max. 220 mm diameter. Dedpfxsvvi Sps Ah Ujkw Storage location: Nattheim

Condition: used, Year of construction: 2007, HOLZ-HER – 6310 CUT 110 580 Computer-controlled Panel Saw Watch the video of the machine: Year of manufacture: 2007 Machine number: 136 The machine has been overhauled in all essential mechanical components. New PC, new label printer, etc. in 2023 Technical Specifications and Description: Base machine: Pressure beam saw Version: Fence on the right Saw cycle: away from the fence Cutting length: 5,850 mm Cutting width: 5,850 mm Saw Blades: Main saw blade Ø 400 x 4.4 x 30 mm, Z72, FZ/TZ (not included!) Tungsten carbide pre-scoring blade Ø 180 x 4.4/5.4 x 30 mm, conical (not included!) Cutting Height Cutting height: 110 mm Saw blade projection: 120 mm Pressure beam: pneumatic, pressure adjustable Extraction: Central moving dust channel on the unit Extraction port base machine: 1x Ø 160 mm, positioned on the right side Dust channel in pressure beam: 2x Ø 120 mm – 1x top left, 1x top right Dodpfx Ajw I Uxpeh Uekw with cutting length 5,850 mm: 3x Ø 120 mm – 1x top left, 1x top center, 1x top right Extraction air velocity: 30 m/s Air volume: 4,000 m³/h at 30 m/s Compressed Air Air consumption approx. 32 l/min at 6 bar per cutting cycle Switchable collet chuck pressure Switchable from the control panel For sensitive panel materials Automatic cutting length limitation The saw unit detects the workpiece end using a non-contact sensor and optimizes the cutting cycle Offcut device For cutting without leftover piece Clamps retract into recessed pressure beam Width Stop Precision-guided, freely programmable width stop with clamps Rack-and-pinion drive for precise positioning With surface-hardened linear guides Return speed of panel pusher: 80 m/min Forward speed of panel pusher: 80 m/min (EU – max. permissible forward speed 25 m/min) Max. opening for clamps: 120 mm for longitudinal and cross cuts Clamps, floating design Compensate for internal stress in panel packs upwards – 6 pcs for 3,250 mm cutting length – 7 pcs for 4,250 mm cutting length – 8 pcs for 5,850 mm cutting length Control CUTCONTROL 2 with 15" TFT display Operating system Windows 2000 RJ45 network connection 10/100 Base-T Fast Ethernet Intel Celeron processor Midi tower US keyboard Optical mouse CD ROM drive Control panel located on fence side Clearly arranged graphic-based operator interface for easy handling and order/material management on Windows basis Realtime display Large, clearly structured buttons All functions accessible from one level No limits in input fields and unlimited job inputs possible Control Functions Direct Cut: Cutting by direct entry of cutting dimensions. Processing of absolute, serial, or format cuts, with integrated grooving, notching, or positioning cuts. Unlimited jobs programmable. Job prioritization (prioritization possible at any time). Order programming parallel to cutting. NC Cut: Processing of optimized jobs. Graphical machine overview with machine process flow function ...

Condition: used, Year of construction: 2005, Used machine Year of manufacture: 2005 Dkjdpfxewlwn Ne Ah Usw Features and technical specifications: Base machine 555 Workpiece support with 8 consoles, pneumatically clamped Drilling unit 7968: - 18 vertical drilling spindles with 32 mm spacing - Individually selectable - T-shaped arrangement - 12 on the X-axis and 6 on the Y-axis - Max. drilling diameter: 35 mm (depending on panel thickness) - Spindle extension stroke: 70 mm - Rotation direction: alternates between right- and left-hand rotation - Speed: 4725 rpm, steplessly adjustable - 2 horizontal drilling units in X-direction, 1 horizontal drilling unit in Y-direction Sawing unit 7946: - 3.5 kW - 90° pneumatic swivel - Speed: 5300 rpm - Tool holder: outer diameter = 200 mm, inner diameter = 30 mm, width = max. 3.5 mm - Sawing/grooving in X and Y direction Milling unit 7935: - With 6 kW spindle, water cooled Milling unit 7982: - For lock case milling Tool changer 7996: - 18-slot magazine (carousel) Vacuum pump 140 m³/h Manual control device PC control with TwinCAM WOP system Siemens control Availability: short-term Location: Poland

Condition: used, Year of construction: 2001, Used machine Year of manufacture: 2001 Condition: well maintained Features and technical data: Cutting length: 4300 mm Cutting height: 2200 mm Cutting depth: 45 mm Motor: 3 kW Saw blade diameter: 220 mm with SuperCut scoring unit Dkjdpfoxb Hf Hox Ah Uew with automatic shifting grid with complete length stop with strip stop Availability: short-term Location: 65439 Flörsheim