Used Ims Phy 110 for sale (8)

Condition: reconditioned (used), Year of construction: 2002, Pressure 100 ton Clear width between the two uprights: 420 mm Ram dimensions: 610 x 410 mm Gbodsx Adp Eepfx Ag Teg Table dimensions: 950 x 650 mm Installation height, ram bottom position: 400 mm Adjustable ram stroke: 0–140 mm Ram adjustment: 90 mm Strokes per minute: 55 Clamping pin: D 50 H7 Motor power: 7.5 kW Dimensions: H 3050 x W 1030 x D 1905 mm Weight: 7000 kg Press is equipped with: - Air clutch - Hydraulic overload protection - Central lubrication system - Bronze guide strip

Condition: good (used), punching force: 45 t, - Capacity 45 tons Gbsdpfx Aju Havwsg Tsg - Hydraulic - 4 stations - Foot control - Emergency stop - 400V

Year of construction: 1998, condition: ready for operation (used), machine/vehicle number: 2131, Max. pressure: 55 kN Throat: 175 mm Adjustable punching stroke: 0 - 28 mm Number of strokes at 15 mm stroke: 30 Notching stroke adjustable: 0 - 60 mm Hydraulic drive: 380 V, 3 kW Floor space required: 1170 x 620 x 1470 mm Gbsdpsnacy Tjfx Ag Teg weight: 930 kg

Condition: used, Inverter welding machine for manual electric welding IMS - GYS type PROGYS FLEX 280A CEL MMA welding machine, inverter welding machine, manual electric welding inverter Serial no. IEC 60974 Year of manufacture 2020 Power with mains operation 400 Volt (40% ED) 280 Amp. Power with mains operation 400 Volt (60% ED) 200 Amp. Power for mains operation 400 Volt (100% ED) 170 Amp. Power for mains operation 230 Volt (40% ED) 200 Amp. Power for mains operation 230 Volt (60% ED) 180 Amp. Power for mains operation 230 Volt (100% ED) 150 Amp. Adjustment range 5-280 Amp. stepless Gedpfsvg Rh Tsx Ag Tsbg Mains connection 230 / 400 Volt, 50 Hz. - Operating voltage from 110 to 480 volts alternating current - Adapts fully automatically to the existing mains supply - equipped with 16 Amp. CEE plug for 400 Volt mains voltage - Hot-start function (optimizes the ignition behaviour, simplifies the welding start of electrodes that are difficult to ignite) - Anti-stick function (optimizes electrode guidance and prevents the electrode from sticking) - Arc-Force function (optimizes arc stability and improves penetration) - Digital display - Plug socket for remote control connection - Earth cable with plug connection - Electrode tongs with 3 meter cable and plug connection - Stick electrode welding, can be used for all electrode types up to Ø 5 mm - TIG-DC welding (without TIG hosepack) - The device may be connected to a flexible three-phase power supply between 110 V and 480 V or to a fixed three-phase 400 V power supply (50 - 60 Hz) plus ground wire. This appliance may only be connected to a 3-phase power supply system with 4 conductors, where the neutral conductor is earthed. Dimensions (appliance without cable) L x W x H 470 x 270 x 430 mm Weight (without cable) 23 kg New, unused

Condition: good (used), Year of construction: 2001, Table 950x650 mm, ram 610x410 mm, stroke 0-140 mm Godpfx Asqgcaajg Tobg

Year of construction: 2003, condition: ready for operation (used), There are two identical presses available, max. stroke speed: 200mm/s, oil viscosity: 46cSt a 40°C, max. hydraulic/operating pressure: 25/ 210bar, weight of the half tool: 10t, pump power at 75/ 210bar: 200/ 70l/min, pump motor power: 30kW, weight: 25t. Gjdpfx Ageivt R Aj Tsbg

Condition: used, functionality: fully functional, ---IMS PHY 1100 PUNCHING MACHINE, YEAR 2008, MAX PUNCHING 32X26 mm. Overall dimensions 185X75X210(h) cm, Machine weight 1800 kg ---IMS HY 45 VS PUNCHING MACHINE YEAR 2005 Hydraulic single punch Power 45 ton 5 work stations (slotting, angular cutting, bar cutting, shearing) Punching diameter 32 mm X 12 mm Slotting 50X40 x 6 mm 90 degree angular cutting 80 mm X 80 mm X 8 mm Plates 300 mm X11 mm Swan neck 170 mm Gedpjwn Hu Rofx Ag Tebg Controlled or free descent Self-moving extractor Adjustment of punch upper dead point Check squares Motor power 4 kW Overall dimensions 100X60X180(h) cm, Machine weight 500 kg

Condition: refurbished (used), Year of construction: 1996, functionality: fully functional, TECHNICAL FEATURES: Press Model: T25-VE Year of construction: 1996 Nominal force: kN 250 Free passage between the uprights mm: 220 Distance between the axis of the connecting rod and the uprights (notch) mm: 160 Dimensions of the mallet mm: 250x130 Worktable dimensions mm: 500x310 Minimum distance between worktable and mace with high adjustment and mallet all the way down mm: 275 Mace adjustment mm: 50 Adjustable stroke mm: 0÷60 Shank hole diameter mm: 40 No. strokes per minute: 155 Engine power KW: 1.5 Total mass Kg: 950 Operating voltage V: 380 Frequency Hz: 50 Dimensions mm: H=1890; L=1000; D=980 Lubrication pump motor power Kw: 0.09 Complete with user manual and CE compliance Warranty six (6) months excluding electronic parts. NEW COMPONENTS INSTALLED: - Front and side safety guards with safety keys; - Motor bearings; - Tang locks; - Flywheel bearings; - Flywheel belts; - Work surface brightened on CNC machine Gjdpfx Aottwfyog Tobg