Used Powder Furnace for sale (1,821)

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Lrjdpofzccnjfx Akqsu Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Ledpfx Aksfz I Rxjqoru Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2024, condition: new, functionality: fully functional, Forced-air curing oven Powder coating oven NEW SLS-90/O * D+t Through-feed oven, divisible Working dimensions: 1400 width x 2000 height x 6500 depth Overall dimensions: 1920 width x 2810 height x 6800 depth Power supply: Electric Rated power: 90 kW Voltage: 380V Frequency: 50-60Hz Door type: 2 doors on each side - through-feed oven Anti-explosion lock Warm-up time: 15-30 min. (180 °C) Ledpfscutrlox Akqeru Homogeneity: < ± 3 °C at 180 °C Max: < ± 3 °C Maximum temperature: 230 °C Transport: optional Air circulation: Forced air Heaters: Interchangeable roof heating panels Airflow: Vertical Fan: Radially mounted on interchangeable panels Door: Double, two doors on two sides (through-feed oven) Divisible Motor power: 1.1 kW Capacity: 6480 L Warranty: 12 months GERMAN-SPEAKING CONTACT PERSONS IN GERMANY FEEL FREE TO INQUIRE Delivery time: approx. 12 to 16 weeks after order Shipping costs are calculated individually. We also offer systems tailored to your requirements. More information at Romer Germany Powder coating, electrostatic painting, Powder Coating, Powder painting, plastic powder, Peinture en poudre, thermoplastic, Verniciatura a polvere, Poederlakken, Порошковая окраска, Порошкове фарбування, powder coating booth powder coating system powder coating plant powder coating booth for powder coating surface technology powder gun powder guns curing oven powder coating oven industrial oven INDUSTRIAL OVEN, forced-air curing oven, powder coating oven

Condition: new, power: 14 kW (19.03 HP), inner dimension length: 1,000 mm, inner dimension width: 1,000 mm, inner dimension height: 1,000 mm, total length: 1,395 mm, total width: 1,600 mm, total height: 2,045 mm, overall weight: 400 kg, control type: NC control, actuation type: electric, fuel type: electric, continuous power: 14 kW (19.03 HP), Equipment: CE marking, ⭐⭐⭐⭐⭐ ⚡ Top Service ⚡ Fast Delivery ⚡ Professional Support! ✈️ Shipping costs are calculated separately according to the delivery address. Please contact us for an individual transport quote. ✅ Made to order ✅ Brand new, unused professional industrial product ✅ Proton Maschinenbau GmbH is the sole authorized European distributor for Matech products ✅ 2-year warranty ⏱️ Delivery time: approx. 4 weeks after receipt of payment Please also inquire about current stock availability. Lredpfx Aswfpp Eekqou ➖➖➖➖➖ ⭐ Matech Powder Oven with Electric Heating – MATOVENB-101010 MATECH QUALITY – WITH PROTON SERVICE! ☘️ Compact ☘️ Efficient ☘️ Professional Curing ✅ Electrically heated powder oven ✅ Compact design for small and medium-sized workpieces ✅ Digital temperature control up to 220°C ✅ Adjustable curing temperature and curing time ✅ Automatic exhaust fan function adjustable ✅ Acoustic signal at the end of curing time ✅ Insulated door with special locking system ✅ Robust sandwich panel construction ✅ Excellent heat retention through strong insulation ✅ Timer function from 10 minutes to 24 hours ✅ Automatic shut-off after process completion ✅ Can be used with a mobile workpiece trolley ✅ Optional insert shelving system for small series ➖➖➖➖➖ ♨️ Also available with upgrade for up to 500 °C for high-temperature processes (optional) ➖➖➖➖➖ Technical Specifications: ✔️ Electric heating power: 12 kW ✔️ Blower output: 1,500 m³/h ✔️ Circulation fan: 0.75 kW ✔️ Total output: approx. 14 kW ±10% ✔️ Digital temperature control ✔️ Stepless temperature adjustment up to 220°C ✔️ Interior: 1.2 mm galvanized steel ✔️ Exterior: 1.2 mm powder-coated steel ✔️ Insulation: 150 mm ✔️ 50 mm rock wool + 100 mm glass fiber ✔️ Adjustable curing time ✔️ Adjustable exhaust fan function ✔️ Acoustic signal after process end ✔️ Control panel: 1 piece ➖➖➖➖➖ ⚙️ Optional Control Functions ✅ PID control for precise temperature management ✅ Touchscreen control panel and smartphone operation ✅ Ramp heating mode for defined temperature curves ✅ Storage of process parameters ✅ Weekly & monthly reports at the push of a button ➖➖➖➖➖ ⚙️ Safety and Process Control Safety sensor for overheating prevention Automatic shut-off in case of fault Acoustic warning signals for errors Fume extraction via automatic ventilation ➖➖➖➖➖ ♨️ Ramp-Heating Mode (optional) Control temperature profile and holding times precisely, e.g.: • Reach target temperature in defined time • Hold at set temperature for desired period • Controlled cool-down to target temperature • Automatic notifications for process events ➖➖➖➖➖ ✅ No repeated settings required! The oven stores your process parameters – batch after batch. This saves you time and prevents errors. ➖➖➖➖➖ ✳️ Maintain your liquidity! We offer various financing models so you can flexibly plan your investment. Please contact us for information about leasing, hire purchase, or installment options. ➖➖➖➖➖ ✨ Buy directly from the official European distributor and secure the advantage of professional service and guaranteed quality! ✨ Custom dimensions or individual configurations are available on request. We are happy to design a suitable solution for your workshop. Inquire now – make your business ready for professional powder coating!

Condition: new, Year of construction: 2025, Powder coating oven The oven is designed for drying elements painted with water-based and solvent-based varnishes. Working dimensions (mm): 1500 (w) x 4000 (d) x 2000 (h) Technical data: • Power consumption: 59 kW. Equipment: • Top transport, • Touch control panel, • Hot air circulation (Equal temperature throughout the furnace, acceleration of the workpiece heating process), • Locks for safe opening and closing, • Time module, • Thermoregulator (controls the temperature inside and maintains it at an appropriate level), • The oven is equipped with rails for easy transport. • Maximum working temperature: 230°C. CHOOSE BUMEX SP. Z O.O. Very high quality of the machines offered on the market. Ledpfx Akeg Ib Epjqeru Professional advice and service. Guarantee. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our clients. All products of the brand BUMEX SP. Z O.O. have WE certificate. We offer our own transport - prices are agreed each time for a given offer. We issue VAT invoices. Short lead times! Possibility to order machines in various, personalized configurations and dimensions! Please do not hesitate to contact us.

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Lsdpfx Aksfzb Rcoqoru Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 Ledpjfx Nfmefx Akqeru 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning. Lodpfjfzkqmox Akqeru

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Lrodpfx Akjfy Txyjqju Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Condition: good (used), functionality: fully functional, Complete Industrial Powder Coating Line for Sale We offer a complete industrial powder coating line in good working condition. The installation has been professionally maintained and is suitable for coating a wide range of steel and metal products. Equipment includes: Pretreatment system Drying oven Powder coating booth Powder spray equipment Curing oven Conveyor system Electrical control system The complete line is available for immediate sale and can be inspected by appointment. Condition: Well maintained Lrodpfx Aszqur Hokqju Fully operational before dismantling Suitable for industrial production GEMA OptiStar CG07 Powder Coating Gun

Condition: used, Year of construction: 2010, machine/vehicle number: 1000017741, inner dimension length: 1,000 mm, inner dimension width: 840 mm, inner dimension height: 815 mm, operating temperature: 1,700 °C, usable tank capacity: 685 l, No minimum price – guaranteed sale to the highest bidder! The machine was professionally dismantled and stored. All parts and connections are labeled for reassembly. An on-site inspection is possible at any time. TECHNICAL DETAILS Furnace chamber and usable space Usable batch space (W × H × L): 840 × 815 × 1,000 mm Total length of the graphite box: approx. 1,100 mm Usable volume: approx. 685 l Operating temperature: max. 1,700 °C Operating temperature under partial pressure: max. 1,500 °C Operating temperature under vacuum: max. 1,700 °C Temperature uniformity: ± 10 K Temperature fluctuation in the steady state: ± 5 K MACHINE DETAILS Process pressure range: 1 × 10⁻² < p < 1,040 mbar Final pressure in the empty, clean, and cold furnace: < 1 × 10⁻² mbar Leak rate: < 5 × 10⁻³ mbar·l/s Power supply: 3 × 400 V, 50 Hz Permissible voltage fluctuation: max. ± 5 % Installed heating power: max. approx. 190 kW Electrical power of the pump station: approx. 14 kW Cooling water flow rate: approx. 150 l/min Cooling water temperature: 20–30 °C Cooling water pressure: 2–4 bar Cooling water quality requirements: according to specification PW 800 943 ND Compressed air for valve operation: 4–5 bar Nitrogen inlet pressure: 5–7 bar Hydrogen inlet pressure: 5–7 bar EQUIPMENT Double-walled furnace chamber made of stainless steel with water cooling Lsdez I Tt Iepfx Akqeru Internal graphite box for precise guidance of the process gases Post-cleaned graphite components Automatic control of the entire process Pump station Labeled lines and connections for easier recommissioning Note: Two internal graphite heating elements were damaged during dismantling and must be replaced.

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, input voltage: 400 V, workpiece height (max.): 2,100 mm, workpiece length (max.): 2,000 mm, Ideal-Line Powder Coating Line | Gema Automatic Booth | 17 Guns | Chemical Pretreatment | 250 m Overhead Conveyor Complete Powder Coating Line 3-stage chemical pretreatment system | Dry-off oven | Automatic powder coating booth with recovery system | Curing oven | Overhead conveyor For sale: a complete used powder coating line in good working condition. The line is technically operational and designed for continuous coating of steel and aluminum components. The line consists of: • Overhead conveyor system • Surface pretreatment section • Dry-off oven after washing • Automatic powder coating booth • Powder recovery system with cyclone and filtration unit • Curing oven • Loading and unloading stations • Control cabinet and automation system _____ Technical Specifications • Manufacturer: Ideal-Line, booth and application system by Gema • Year of manufacture: 2012 / 2015 • Maximum part dimensions (L × W × H): 2000 × 750 × 2100 mm • Powder application system: Gema automatic system with 17 powder guns • Pretreatment: 3-stage chemical pretreatment washer • Oven heating source: Direct-fired natural gas • Conveyor length: Approx. 250 m • Power supply: 400 V _____ Technical Condition Lsdpfx Akez Rnu Tsqjru The line has been regularly maintained and operated in continuous production service until 30 September 2026. _____ Additional Information • Technical documentation available • Sale due to plant closure • Inspection available by appointment • All de-installation and removal costs buyer is responsible Location • Koszalin, Poland Price • Cena: 369 000 EUR excl tax

Condition: excellent (used), Year of construction: 2022, operating hours: 600 h, functionality: fully functional, machine/vehicle number: PO210417, total width: 4,600 mm, total length: 25,000 mm, total height: 3,000 mm, type of input current: three-phase, energy consumption: 1,700 kWh, input current: 2,230 A, The AG series of convection tempering furnaces with forced air circulation (Northglass fifth-generation furnaces, featuring proprietary focused convection technology) was developed to meet the growing customer demand for more efficient low-E glass tempering, improved product quality, and reduced energy consumption. The AG series furnace integrates the advantages of a four-convection furnace, primarily offering benefits in terms of higher productivity, superior product quality, and easier process control. The furnace consists of loading conveyors, a heating section, a convection system (upper and lower), a flat tempering/cooling section, and an unloading conveyor. The equipment package includes air ducts and a device control system. Max. working width: 2,850 mm. Max. loading length: 5,000 mm. Max. glass loading area: 2,850 x 5,000 mm (5-19 mm), 2,850 x 4,600 mm (4 mm). Upper fan convection: 6 fans x 4 kW, lower: 6 fans x 3 kW. Main technical data is attached in a PDF file. Lrjdpfxez Dhm Ue Akqju

Condition: new, Year of construction: 2026, It is a complete painting system, comprising the following components: 1) An oven with an air heater (the type of fuel can be adapted to the client's specifications). 2) A spray painting booth equipped with an absorbent filtration system suitable for even the most demanding paint applications. 3) Two parking areas where parts can be placed after painting or curing. Lrodpfeyaqt Tex Akqou 4) A rail system that enables easy movement of parts from one station to another. 5) A trolley for transporting the aforementioned parts. 6) A fully integrated and robust steel structure, engineered for high static stability and to minimize the risk of component failure. From both a design and technical specification perspective, the above installation constitutes a comprehensive and autonomous electrostatic painting line. For limited systems, there is an offer for the complete package at 115,000 euros.

Condition: used, Desktop Metal Desktop Metal 3D Printer Complete System 3D Metal Printer Studio System from Desktop Metal Complete system: 3D printer + debinding machine + sintering furnace Desktop Metal The three-part solution includes a 3D printer, debinder, and furnace. Manufacturer: Desktop Metal Model: Desktop Metal Studio System Operating condition: Used (Good) Year of manufacture: 2019 Includes: Bound Metal Deposition (BMD) technology Features: Printed materials: Metal Technology: FDM Application: Industrial Other features: Office X-axis travel: 30 cm (12 in) Y-axis travel: 20 cm (8 in) Z-axis travel: 20 cm (8 in) Ljdpfx Akozd Tllsqoru Description: In contrast to laser-based systems that selectively melt metal powder, the printer extrudes bound metal rods – similar to an FDM printer. This eliminates the safety requirements often associated with 3D metal printing, and enables new features such as the use of closed-cell fillings for lightweight strength. Desktop Metal Studio Debinder (Delamination machine) Fully automatic debinding Cleaning tank: 17.4 L (in process) / 22.5 L (storage) Description: The debinder prepares green parts by dissolving the primary binder for sintering. With a low-emission design, it requires no external ventilation and is safe for an office environment. Automatic liquid distillation and recycling mean that no refilling is required between cycles. Desktop Metal Studio Sinter Furnace Hybrid technology (microwave & conventional heating elements) Build volume: 305x205x205 mm Carbon housing Gas supply: 2 x 900 L gas cylinders Heating power: 20 kW Function: Sintering Configuration: Chamber Heat source: Gas Other features: High temperature, automatic Maximum temperature: 1,400 °C (2,552 °F) Description: Fully automated and sized to fit through an office door, the furnace delivers industrial-grade sintering in an office-friendly package. Built-in temperature profiles, tailored to each design and material, ensure uniform heating and cooling without the residual stresses that occur in laser-based systems. Condition: used Scope of delivery: (See image) (Changes and errors in technical data, information is subject to change!) We will be happy to answer any further questions you may have by telephone.

Year of construction: 2008, condition: ready for operation (used), A complete bulk powder coating system MEEH powder coating and dust filter system is available. Product dimensions X/Y/Z: 8000mm/800mm/3000mm, max. product weight: 1000kg, total surface area of all openings: 12.9m², max. permissible powder injection quantity: 90kg/h, extraction capacity: 18000m³/h, total system dimensions X/Y/Z: approx. 28m/13m/6m, compressed air requirement: approx. 38nm³/h, compressed air: 8bar, connected load: approx. 30kW. 1) Manual powder stand with suction, internal dimensions X/Y/Z: 10m/3m/4m, external dimensions X/Y/Z: 10040mm/3370mm/4600mm. 2) Chamber dryer MEEH KTÖ240, year of construction: 2008, air capacity: 30000m³/h, heat output: 240kW, burner: Weishaupt, burner year of construction: 2019, fuel: heating oil, internal furnace dimensions X/Y/Z: approx. 8530mm/4610mm/5840mm, external furnace dimensions X/Y/Z: approx. 8200mm/3500mm/4000mm. 3) Lifting and lowering station with 2 chain hoists H/S 160, year of construction: 2008, speed: 4m/min, max. load: 2x500kg, lower edge of traverse - floor distance: approx. 3700mm. 4) Electric traversing platform EQ 160, year of manufacture: 2008, max. load: 2000kg, speed: 12m/min, max. traverses: 3, total traverses: 14, total traverse positions: 14, traverse length: 8m, load: 1000kg. Documentation available. On-site inspection is possible. Lrsdpewr Dv Hjfx Akqsu

Year of construction: 2003, condition: used, functionality: fully functional, machine/vehicle number: HWO 1/9-5.2​, - The system is located at the Geberit Keramik GmbH site in Wesel. - The system, including the associated safety technology, performs technical flash firing and re-firing and is prepared for this purpose. - Maximum firing temperature [°C] = 1300 - Current operating temperature [°C] = 1238 - Number of burner groups = 10 - Number of burners = 38 - Number of kiln cars = 18 - Number of kiln cars in the kiln = 9 Lodpfxezu Nvzs Akqjru - Current firing cycle [h] = 17 - 23 - Gross energy consumption [kcal/kg] / [kWh/kg] = 785 / 0.912 - Specific energy consumption [kcal/kg] / [kWh/kg] = 1459 / 1.696 - Gas connection capacity [m³/h] = 770 - Usable waste heat [m³/h] = 4000 - Standard loading quantity [pieces] = 900-980 ceramic products Dimensions of the housing: - Length [m] = 14.4 - Width [m] = 6.4 - Height [m] = 5.7 - Volume density [m³] = 146.3 Dimensions of the kiln car: - Effective length [m] = 1.45 - Effective width [m] = 5.2 - Effective height [m] = 2.156 - Track gauge [m] = 1.5 (2x) Special features: In 2023, the kiln was completely overhauled and brought up to the latest state of the art. The following changes were made: - Renewal of the kiln roof: The fiber lining in the upper area was replaced with cordierite stones. - Renewal of the burners, including new nozzles, flame tubes and controllers. - Replacement of the media valves; installation of servo motors on the gas and air lines in front of the burners. - Installation of new software; the Simatec control panel was replaced – control is now exclusively via the PC. - Replacement of the O₂ control system; installation of a Zerox probe; installation of an O₂ analyzer for O₂ correction (to improve energy efficiency by approximately 12–14 %). - The system must be dismantled, packed and collected independently by the buyer.

Condition: good (used), 1 x Powder Packing Machine/Powder Depositor Model: AF-PP5 Range of pack: 1-1.5kg Ledpeyt H Aqsfx Akqjru With weigher

Condition: refurbished (used), functionality: fully functional, machine/vehicle number: 3315N130, Year of construction: 2015, total length: 995 mm, total height: 1,600 mm, total width: 1,050 mm, type of input current: three-phase, overall weight: 350 kg, input voltage: 400 V, input frequency: 50 Hz, ambient temperature (min.): 15 °C, ambient temperature (max.): 35 °C, electrical fuse: 16 A, space requirement length: 3,000 mm, space requirement height: 2,400 mm, space requirement width: 1,200 mm, Misan is Czech authorized reseller for machining centers and metal AM machines. Concept Laser QM Powder - inertized industrial powder sieve: - For Concept Laser / GE Additive / Colibrium Additive M2 powder containers. Also compatible with M1 and Mlab bottles. May be used with another machines with compatible bottles. - Suitable for steel, aluminum, inconel, titanium alloys. - Size: 1050 x 995 x 1600 mm - Weight: 350 kg - Power: 3 P/N/PE AC 400V, ±10%, 50Hz-60Hz - Requires inert gas supply: argon or nitrogen, 5 bars Equipment used by customer. First installed in 2015. Fully refurbished by Misan now (new seals, filters, hoses, overflow bottle,...), clean and functional. New container console. Original price: 25.000 Eur Lrjdpfjz Tf Hfex Akqou We are awaiting your contact. Video conference can be set up if needed. Sieving station can be seen at our showroom. Visit is possible upon contact.

Year of construction: 2019, condition: new, Recirculating air convection furnace Gas-fired furnace CGN Powder coating oven NEW – SGS-800/O Gema Optiflex Ledpfxjcw Tzxs Akqjru Width: 2500 mm, Height: 2500 mm, Depth: 12500 mm Directly from the manufacturer. For more information, visit Romer-Deutschland.

Condition: new, Year of construction: 2026, functionality: fully functional, total length: 3,200 mm, total height: 2,400 mm, total width: 1,700 mm, overall weight: 1,500 kg, EASY-TO-TRANSPORT ELECTRIC OVEN – NO ASSEMBLY REQUIRED!!! This system comprises an industrial electric oven with internal dimensions of 1700 × 3200 × 2100 mm, engineered to deliver consistent and reliable thermal processing for demanding applications. The key feature of this oven is that it can be transported in its assembled state, eliminating the need for on-site assembly. The oven is powered by a high-efficiency electric heating unit (2200 × 2100 × 300 mm), equipped with 3 resistance blocks (a total of 9 heating elements), providing a total installed power of 27 kW. This configuration ensures uniform heat distribution and provides sufficient energy for stable and efficient operation under continuous workloads. To optimize internal air circulation and thermal performance, the system incorporates 2 Ø350 mm impellers, driven by 2 electric motors of 1.5 kW each (2 HP). This setup guarantees enhanced airflow dynamics, contributing to homogeneous temperature distribution throughout the chamber. The oven is fully insulated using 180 mm high-density thermal panels, significantly reducing heat loss while ensuring maximum energy efficiency and complete chamber sealing. This construction supports stable operating conditions and minimizes energy consumption. Additionally, the unit is equipped with an advanced control panel featuring all essential functions and operational parameters. The interface is designed with a strong focus on user-friendliness and operational flexibility, allowing the operator to easily adjust and control the system according to specific production requirements. Why this system excels: High power output (27 kW) Lrsdpjyzw Ihofx Akqsu Optimized airflow system (dual motor + impellers) Heavy-duty insulation (180 mm panels) User-friendly and fully functional control system Designed for reliability, efficiency, and industrial performance.

Condition: ready for operation (used), functionality: fully functional, A well built Pedestal Auger Filler from Webb Automation - controls have been simplified and replaced - original hardware and drive units - stainless steel contact parts throughout - three phase supply - automatic level probe to control a separate infeed device - complete unit working well Mounted on frame with castors and jacking feet Height Adjustable platform under outlet Ideal Powder Filler for filling bags or containers Lrsdpfxo Adq U Ij Akqju Request videos and pictures via Whats App Ready to ship worldwide

Condition: new, Year of construction: 2026, functionality: fully functional, This system pertains to an industrial oven with overall dimensions of 5000 × 2500 × 3200 mm, engineered to provide high-performance thermal processing with maximum efficiency and reliability. The unit features a gas-fired boiler system integrated with three high-performance electric motors, ensuring optimal power delivery and consistent operation under demanding conditions. These are coupled with three Ø452 mm impellers, specifically selected to achieve superior airflow characteristics and maximize mechanical efficiency throughout the chamber. The oven structure is fully enclosed with 180 mm thick high-resistance insulated panels, designed to minimize thermal losses, ensure energy efficiency, and provide complete chamber sealing. This construction guarantees stable internal temperature conditions and optimal process control. Additionally, the system includes an advanced control panel interface that supplies all essential operational data and adjustment functions. The interface is developed with a focus on user accessibility and ease of operation, enabling standard personnel to efficiently manage the system without compromising precision or performance. Lrjdpfxoyzw E Ho Akqeu

Condition: excellent (used), Year of construction: 1980, Hot chamber furnace Chamber: 65 x 39 x 22 cm Power: 15.3 kW Lredpfjy E Izysx Akqsu Max temperature: 1000°C Operating mode: electric

Condition: new, functionality: fully functional, power: 55 kW (74.78 HP), Year of construction: 2026, Ball Mill for Powder and Mining Plant: Structure, Function, and Technical Details A ball mill is a key grinding machine widely used in mining, metallurgy, cement, chemical, and powder-making industries. It is designed to grind various ores and other materials into fine powder through impact and attrition between steel balls and the material inside a rotating cylindrical shell. In mining plants, ball mills are essential for ore beneficiation, preparing materials for flotation, magnetic separation, or leaching processes. In powder production, they ensure uniform particle size and high surface area for further processing. Working Principle The ball mill operates on a simple yet effective principle: as the cylindrical shell rotates around its horizontal axis, the grinding media (steel or ceramic balls) are lifted along the inner wall by centrifugal force and friction. When they reach a certain height, they fall freely, striking and grinding the material below. This repeated motion causes both impact and abrasion, reducing the material to the desired fineness. The grinding process can be performed in dry or wet conditions depending on the application. Structural Composition A standard ball mill consists of several main components: Feeding part: Equipped with a feeder or screw conveyor to ensure uniform material input. Discharging part: Can be grate type or overflow type, depending on the discharge method. Rotating part: The cylindrical shell made of steel plates, lined with wear-resistant liners. Lrodpfsq Nf U Esx Akqou Transmission system: Includes motor, reducer, small transmission gear, and electrical control. Grinding media: Steel balls or ceramic balls of different diameters for efficient grinding. The internal liner design and ball size distribution are optimized to achieve maximum grinding efficiency and minimal energy consumption. Technical Details Typical Specifications: Feeding size: ≤25 mm Discharge size: 0.074–0.4 mm Capacity: 0.65–615 t/h (depending on model and material hardness) Cylinder speed: 18–38 r/min Power: 18.5–4500 kW Liner material: High manganese steel, rubber, or alloy steel Grinding media load: 30–45% of cylinder volume Operating Modes: Dry grinding: Suitable for materials that must remain moisture-free, such as cement clinker, limestone, and quartz. Wet grinding: Common in ore beneficiation, where water or slurry improves grinding efficiency and particle uniformity. Application in Mining Plants In mining operations, ball mills are used after crushing to further reduce ore size and liberate valuable minerals. They are integrated into grinding circuits with classifiers, hydrocyclones, and flotation systems. The ground material is classified by size, and oversized particles are returned to the mill for regrinding. This closed-circuit system ensures consistent product fineness and efficient energy use. Common Applications: Gold, copper, iron, and zinc ore grinding Cement clinker and slag processing Silicate and ceramic powder production Coal and mineral powder preparation Conclusion A ball mill is an indispensable piece of equipment in both powder production and mining beneficiation plants. Its ability to grind materials into fine, uniform particles makes it vital for downstream processes such as flotation, sintering, and chemical reactions.