Used Temper for sale (554)

Condition: excellent (used), CTS Temperature testing chamber T-55/1000 Li, water-cooled Temperature range: -50°C to +100°C Rated voltage: 400V 3/N 50Hz Rated power: 9.5 kW Rated current: 18 A Compressor: TFH2511Z / TFH2511Z, refrigerant R404A/R23 The type designation of the CTS chamber series is as follows: e.g., Type T -55/1000/Li 1) T means: Temperature 2) -55 means: lower temperature -55°C 3) 1000 means: 1000-liter test chamber volume 4) Li means: special equipment for testing with lithium-ion batteries Control: 32-bit controller LCD control panel Digital display of setpoint and actual values Numerical input of setpoints Error messages in plain text Ethernet interface RS 232 interface Free switching channels for customer-specific control of the test item Test chamber lighting: energy-efficient, bright LED light strip mounted on the door Insert rack: Stainless steel, support surface 970 x 980 mm Load per rack max. 35 kg Total load with max. rack load 100 kg 1a Conduit NW50 1b Conduit 2x NW125 1c Conduit 2x Rp 314° for Minimax Technical performance data: Temperature tests: Temperature range -50°C to +100°C Temperature deviation ≤ ±0.3 K over time Temperature change rate according to IEC 60068-3-5 Heating 2.5 K/min Cooling 2.5 K/min Thermal compensation approx. 4000 W at +20°C approx. 2200 W at -40°C The technical data refer to an ambient temperature of +25°C, rated voltage 400V, without test item, without thermal compensation and without additional equipment. Options can affect the performance data. Dimensions: Test volume 1000 liters Test chamber dimensions Height, approx. 1000 mm, Width, approx. 860 mm, Depth, approx. 1100 mm Kedpfx Aqjzg Ty Ujpenc External dimensions Height, approx. 1950 mm, Width, approx. 1270 mm, Depth, approx. 1900 mm Operating data: Electrical connection 400 V +6/-10 %, 3/N, 50 Hz Rated current 18 A Rated power 9.5 kW Protection class IP 54 Sound pressure level < 58 dB(A) (measured according to DIN EN ISO 3744 at a distance of 1 m from the front) Weight approx. 1000 kg Heat dissipation to the installation room 10.4 kW Refrigeration unit: water-cooled, low-noise, fully hermetic stepless power adjustment by electronic monitoring and control system, environmentally friendly refrigerant R404A/R23 For your safety as a buyer, the following information! The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, new filling with legally compliant refrigerants 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of supply: (See picture) (Changes and errors in the technical data and information are subject to change!) We will gladly answer any further questions you may have on the phone.

Condition: used, Year of construction: 2001, functionality: fully functional, 1,0 St. gebr. Temperiergerät Hersteller: REGLOPLAS Typ: P140/9/SG51/1K/RT50 Baujahr: 2004 Knsdpfx Aqoxyt Tnopoc Medium: Wasser Temperatur: 140° C Heizleistung: 9 kW

Condition: like new (used), Year of construction: 2018, functionality: fully functional, cooling capacity: 300 kW (407.89 HP), The temperature control unit from Technotrans is available for sale. It has been checked in the workshop for its functionality. Ksdexy Nx Tspfx Aqpenc A short description of the unit can be provided upon request. Medium: Water Heating capacity: 18 kW Operating temperature: max 95°C Direct cooling capacity: 364 kW Pump capacity: 165 l/min Max. pump pressure: 5.1 bar VA tank Interface: TTY 0-20mA with cable

Condition: excellent (used), Treif block dicer in lovely condition. Perfect for producing cubes of meat from frozen tempered blocks. Kodpfxsxrgiyj Aqpsnc

Condition: used, mileage: 100 km, power: 157 kW (213.46 HP), first registration: 03/2026, fuel type: diesel, overall weight: 7,500 kg, gearing type: mechanical, number of seats: 2, loading space length: 4,200 mm, Equipment: ABS, air conditioning, soot filter, Vehicle number: 540075 accident-free, service history, non-smoker ---- ASSISTANCE SYSTEMS * Lane change warning system * Start-off assistant * Rear view camera ENGINE TRANSMISSION & CHASSIS * Traction control (ASR) INTERIOR * Air conditioning LIGHT & VISIBILITY * Green tinted windows * Side marker lights * Daytime running lights Other features Knodsx Egr Ijpfx Aqpec * Chassis color anthracite gray * Driver's cab color E1980 crystal white * Headlight insert. and bumper: Stone Grey * Cab steps and fenders Stone Grey * Wheel trim rings silver grey * Goodyear * Tire pressure monitoring system * Front axle(s): 215/75R17.5 * Driven rear axle(s): 215/75R17.5 * Without spare tire * Steel disc wheels, silver grey * Pneumatic steering column lock * Soft-touch steering wheel, color black * Roof hatch with manual operation * Driver's seat: Air-sprung luxury driver's seat * Passenger double seat, velour cover * Converter 24 V to 12 V, 15 A, 180 W * Emissions class Euro 6 * Manual transmission, 6 gears * Rear axle ratio 3.73 * Mechanical differential lock * 6-speed manual transmission 6S800 OD, 6.58-0.78 * Engine PX-5, 153 kW/208 hp. Cab emblem: 210 * Wheelbase 3.15 m / rear overhang 1.32 m * Standard component layout * Tank for AdBlue 30 l, right side of the chassis * Fuel tank left * AdBlue tank filler cap without locking * Rear underrun protection * Tail lights with bulbs * Battery box left, no spare wheel holder * Longitudinal member 210/4.5 mm, without internal reinforcement * EAS unit right, central discharge * Plastic fuel tank, 110 l * Maximum ambient temperature 38 degrees * Temperate climate * Air intake above, behind the cab * Water separator, heated * Body fastening method BAM 1, console type B * Fixed plug connection. Front driver's cab * Tail lift application * Use with drawbar, type plate, up to max. GVW * Pneumatic connection for trailer, swivel coupling * Crossbar D85-Dc70-V25 ball coupling D85, mounted * Electrical connection for trailer 24V/2x7-pin + 12 V * FGG chassis weight max. 7500 kg * Max. total train weight drive power 18000 kg * First transmission auxiliary drive N./4c-U-32/25 * Exhaust brake * Parking brake actuation with test position * Reverse alarm system * Basic immobilizer * DAF Side and Turn Assist * Alcohol lock, prepared * Electronic stability control (VSC) * Speed limit detection * DAF Drowsiness Detection * Rubber cab suspension, mechanical * Short-haul cab * Side not glazed / rear single glazed * 5 mirrors * Electrically adjustable mirrors * Mirror brackets, structure 2.50 - 2.60 m * Sun visor outside, green, translucent * Headlight beam for right-hand traffic * Halogen headlights with height adjustment * Adaptive Cruise Control with FCW and AEBS-3 * Digital tachograph, VDO 1C, version G2V2 * Speed limiter setting 85 km/h nom. * PACCAR Connect * Antennas: AM/FM + GSM + GPS * FMS connection, prepared * DAF Infotainment System: DAB radio with loudspeaker * Front: 3.60 t, parabola, raised, HD, F36 * Rear axle: 5.00 t, parabola, raised, SR 5.14 * Front axle 1, 3,200 kg, load index 124 * Rear axle 1, 5000 kg, load index 116 * Generator 100 A, batteries 2x 125 Ah * Guarantee Plus drive train-3 years-200,000 km * Meiller DSK Type 3 model 11 * Plug-in storage rack as bulkhead attachment. ---- Subject to prior sale and errors.

Year of construction: 2012, condition: used, functionality: fully functional, The temperature control unit from Plasma, model "Primus", is available for sale with the following technical specifications: Medium: water, Maximum temperature: 150°C, Heating capacity: 9 kW, Cooling capacity: 30 kW, Special equipment: reinforced pump K6 at 60 l/min up to max. 6 bar. The pressure booster pump is used to increase the cooling water pressure during filling; this is necessary if the system pressure is higher than the cooling water pressure. PT 100 sensor. Interface: On/Off, Alarm, PT 100, Temperature monitoring. Knedpfox Eg T Ejx Aqpec

Condition: new, mileage: 25 km, power: 125 kW (169.95 HP), color: white, gearing type: automatic, number of seats: 18, Year of construction: 2026, Equipment: ABS, air conditioning, electronic stability program (ESP), navigation system, soot filter, * 16 passenger seats + 2 folding seats + 1 driver * Double-width swiveling sliding door * Dark-tinted panoramic side windows * MBUX (Mercedes-Benz User Experience) * Intercity seats * Driver's work area lighting * Destination display (Lawo, white) at the front, side, and rear * USB ports in each row * Passenger air conditioning, 13 kW * Roof hatch made of tempered glass * Handrails and grab handles in the interior * Stop button * Microphone for the driver * Speakers in the passenger compartment * Clock with stop function * Glass hammer * Additional interior mirror * Additional turn signals on the roof * Non-extended vehicle * Electrical preparation for a trailer hitch Kedpfx Aozrqu Tsqpenc

Year of construction: 2021, condition: used, Tube manufacturing line Manufacturer: Bazhou Wanxin Industrial and Trading Tube manufacturing line consisting of: Double-station unwinding device Function: Unwinds the coil passively Design: 2-station design with 180-degree rotation, manual expansion Advantages: Fast loading, simple and convenient operation Hydraulic shear and butt welding machine Function: Cuts off the front and rear ends, centers the strip, and welds the strip back together Design: Manual hydraulic shear with cantilever, front and rear pressure rollers, front and rear centering rollers, welding device Cutting method: hydraulic shear Press material method: double-cylinder press Welding method: manual welding Strip storage device Function: To ensure continuous production of the welded tube, a storage unit must be installed after the shear and butt welding platform so that the storage unit can continuously feed the strips while the strip steel material is prepared for stacking, unwinding, butt cutting, and welding. Design: Frame type, with moving and fixed frames (including feeding device) Feeding speed: max. 120 m/min Storage speed: max. 200 m/min Length of stored strips: 200 - 400 m Pinch roller motor: AC 11 kW Forming and sizing machine Working height: +850 mm Power: AC/DC motor: 160 kW, 1000 - 2000 rpm Reducer: Gear hardening Arrangement: Passive five-roll straightening machine, vertical rolls for feeding material, forming through 7 horizontal roll stands and 8 vertical roll stands, guiding, pressing, deburring, cooling, and sizing through 6 horizontal roll stands and 5 vertical roll stands, 1 round sizing stand Round sizing stand: 1 set of smoothing device, two sides with 8 rolls each, 4 rolls per side. 30 mm, 40cr, quenching, tempering, and hardening Horizontal roll shaft: 60 mm, bearing at position 55, made of material 40Cr Heat treatment of horizontal roll: surface hardening, HRC 50-55 Bearing guide: forged steel 45# Vertical roll shaft: 40 mm, material 40Cr, quenched, tempered, and hardened Vertical and horizontal rolls - Design: Portal design, opening width: 120 mm, clamping of horizontal roll stand: adjustment via worm gear Material of horizontal and vertical roll stands: welded (aging annealing) Gearbox: Gear: Spiral bevel gear Shaft of pinch roll: 50 mm, 2 rolls for pinching, adjusted via a manual screw rod Guide shaft: 40 mm Deburring knife: 2 pcs., one for working and one as a spare Cooling tank Cold cut-off saw Function: The cold cut-off saw is one of the most important machines in the ERW tube line. It can cut the tubes to the preset length during high-speed production. Knedpfxezuz H Sj Aqpsc Type: KK-5-50 Tube diameter: Round tubes 16-63.5 mm and corresponding square and rectangular tubes Length cut: any length between 1 - 6 m Material thickness: 0.6-2.5 mm Drive motor: 11 kW servo Yaskawa Feeding motor: 2.9 kW serco Yaskawa Saw motor: 11 kW, AC motor with frequency converter Feeding method: Servo multi-stage speed feed Speed adjustment: max. 110 m/min Clamping force: pneumatic Drag chain Saw blade: 400 mm Saw gearbox model: KK-80 Saw stroke (device length): 3 m Device dimensions: 4500 x 1500 x 1300 mm Conveyor track, table, and packaging machine Function: The formed tubes are automatically removed from the roll.

Operating hours: 13,241 h, condition: used, machine/vehicle number: 24-02577-4 / TT-380, Temperature control unit by Tool-Temp AG, used and untested. This device is suitable for tool temperature regulation, injection molding, and process engineering applications. Operates with oil and water as heat transfer media in a single-circuit system. Maximum supply temperature is 360°C (oil) or 90°C (water), with a heating capacity of 24 kW. The pump delivers up to 90 l/min at 6.0 bar; the control system is MP-888. Operating hours are specified at 13,241, year of manufacture unknown. Accessories include a digital hour meter, analog pressure gauge, transport castors, and crane lugs for loading. Kedpfx Asy St Urjqpsnc

Condition: ready for operation (used), Year of construction: 2024, operating hours: 2,489 h, travel distance X-axis: 400 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 440 mm, number of axes: 3, This 3-axis HAGE 3D Mex-One-A was manufactured in 2024. It features a build area of 400 mm x 600 mm x 440 mm and a heated print bed that reaches up to 180 °C. The machine is designed for unmanned 24/7 operation and includes an advanced filtration system for effective exhaust air purification. If you are looking to get high-quality 3D printing capabilities, consider the HAGE 3D Mex-One-A plastic 3D printer we have for sale. Contact us for further details. • Fused Filament Fabrication (FFF/FDM) • Total Machine on Hours: 4,294 h • Extruder 1 Hours: 1,914 h • Extruder 2 Hours: 575 h • Total Printing Hours: 2,489 • Heated Build Chamber: Up to 100 °C • Heated Print Bed: Up to 180 °C • Maximum Nozzle Temperature: 450 °C • Layer Thickness: From 0.05 mm • Traverse Speed (XY): Up to 250 mm/s • Printing Speed: Up to 200 mm/s • Build Rate: Up to 150 g/h • Print Head: Water-cooled Dual DSD • Extrusion Pressure: Adjustable • Nozzle Diameter: 0.1–1.0 mm (0.4 mm standard) • Inactive Nozzle Lift: Free stroke Kodpfezk Erqsx Aqponc • Part Cooling: Up to 4.8 m³/h • Automatic Print Bed Calibration: Multi-point topography measurement • Exhaust Air Purification: Activated carbon and HEPA filtration • Engineering Plastics Capable: Yes • CE Marked: Yes Drying Chamber (DCU), 2024 (optional, not included) • Internal Dimensions (X/Y/Z): 630 × 390 × 260 mm • Capacity: 3 Movable Small Spools (Upper Section) • Capacity: 2 Movable Large Spools (Lower Section) • Maximum Drying Temperature: 100 °C • Filament Feed: Direct Feeding from the Chamber with up to 4 Spools • Automatic Air Exchange and Moisture Removal • Tempering Chamber Internal Dimensions (X/Y/Z): 418 × 601 × 401 mm • Loading Areas: 3 Loading Positions for 600 × 400 mm Sheets or Grids • Maximum Tempering Temperature: 200 °C • Simultaneous Operation of Drying and Tempering Chambers • External Dimensions (X/Y/Z): 1,600 × 695 × 580 mm • Total Weight: Approx. 100 kg • Control: Siemens LOGO! • Maximum Power Consumption: 6 kW • Electrical Connection: Three-Phase AC 230 V, 16 A Fuse per Phase

Condition: used, Year of construction: 2007, used to produce innerliners Equipment Specifications Summary Forming and Tool Dimensions Maximum frame inner size: 2005 × 905 mm Maximum tool base size: 2000 × 900 mm Minimum tool base size: 700 × 500 mm Maximum sheet size: 2090 × 960 mm Minimum sheet size: 790 × 560 mm Maximum tool height: 800 mm (550 + 250 mm) Maximum formed workpiece height: 550 mm Maximum sheet stack height: 1000 mm Maximum pallet height: 180 mm Heating System Upper heating power: 83.3 kW Lower heating power: 71.3 kW Upper preheating power: 52 kW Lower preheating power: 46.8 kW Drive Motors & Auxiliary Equipment Oil pump motor power: 19 kW Vacuum pump motor power: 23.4 kW Sheet centering motors power: 0.24 kW Sheet feed motor power: 2.2 kW Sheet feed width-adjustment motor power: 2.2 kW Sheet picker motor power: 0.37 kW Fan motor power: 5.5 kW Shear motor power: 2.2 kW Carriage motor power: 2.2 kW Rotary table motor power: 1.1 kW Scrap cutter motor power: 3.0 kW Scrap conveyor motor power: 0.37 kW Finished workpiece discharge belt motor power: 0.75 kW Cross-cutting motor power: 0.25 kW Cross-cut scrap conveyor motor power: 0.22 kW Transfer unit motor power: 1.5 kW Auxiliary units maximum consumption: 5.1 kW Tempering unit power: 52 kW Electrical Requirements Maximum installed power: 375 kW Power consumption at 70% load: 262.5 kW Vacuum System Vacuum pumps capacity: 750 m³/h (250 × 3) Tool vacuum tank capacity: 2,000 L Bell vacuum tank capacity: 2,000 L Hydraulic System Required oil quantity: 600 L Hydraulic operating pressure: 10 MPa Maximum hydraulic operating pressure: 18 MPa Pneumatic System Required air pressure: 600 kPa Compressed air consumption: 1,300 N liters/cycle Cooling Water Requirements Incoming water pressure: 200-300 kPa Incoming water temperature: 12-20 °C Outgoing water temperature: 30-35 °C Mechanical Characteristics Lower tool holder force: 9,000 kg Machine weight: 35,000 kg (35 tonnes) Key Utility Requirements Electrical Supply: 375 kW installed load Knedpfx Aqszumt Dopec Compressed Air: 600 kPa, 1,300 N liters/cycle Cooling Water: 200-300 kPa at 12-20 °C Hydraulic Oil Capacity: 600 liters Vacuum Capacity: 750 m³/h with two 2,000-liter vacuum tanks Fully automatic thermoforming machine designed to shape plastic sheets suitable for high-capacity industrial applications. Thermoformer details: Forming area 2005mm x 905mm Max forming depth 550mm 3x loading stations. 1 x heating station. (pre-heating, final heating, upper and lower elements) - ceramic/quartz infrared elements Pressure and vacuum forming operation. 4 x side trimming presses. (rotary) Guillotine. Scrap collection end station. Automation: Fully automatic batch processing with operator control panel featuring manual/automatic modes. Industrial grade build with multiple access doors, observation windows, and integrated ventilation heat management. Year of manufacture 2007.

Condition: used, TERMIK Range Gas or diesel-powered 5 decks, 15 openings Ksdszyaktopfx Aqponc Usable area: 23.10 m² With integrated loading elevator Maximum power: 128,000 kcal/h, equivalent to 149 kW Forced hot air circulation 2 fans on the 180 series High-efficiency heat exchanger Heat distributed between ceiling and floor Independent steam generator per chamber Steamers located near the combustion cylinder Steamers’ power consumption: 1.5 to 2 kW Standard steam generator: 4 kW Stainless steel and tempered glass doors Removable doors for cleaning Overpressure valves on each chamber Electrical panel with IP55 protection Steamers accessible from the front Internal dimensions: 1850 x 2500 mm External dimensions: 2485 x 3650 mm Loading clearance: 3060 mm Used Tagliavini CT 185/L cyclothermic oven – 23.10 m² baking area General Overview The Tagliavini TERMIK CT 185/L is a professional, multi-deck cyclothermic oven designed for bakery operations that require a large baking area and even heat distribution. This configuration features 5 baking chambers for a total usable area of 23.10 m², with internal dimensions of 1850 x 2500 mm. The cyclothermic principle is based on the forced circulation of heat from the combustion chamber. In the 180 series, two fans direct the heat flow through the ducts surrounding the chambers, achieving a balanced temperature from the bottom to the doors. The CT 185/L can operate on gas or fuel oil/diesel.

Condition: used, mileage: 25 km, power: 125 kW (169.95 HP), first registration: 05/2026, brakes: retarder, color: white, number of seats: 19, Year of construction: 2026, Equipment: ABS, air conditioning, electronic stability program (ESP), soot filter, This is a new vehicle without registration! * 19 passenger seats + 1 tour guide seat + 1 driver * Roof hatch made of tempered glass * Driver's workstation lighting * Passenger air conditioning, 13 kW Knodpfx Asy D U D Eeqpoc * Premium luggage rack with individual ventilation nozzles * Foldable tour guide seat with 3-point seat belts * Comfortable travel seats with fabric/leather upholstery, 3-point seat belts, adjustable armrests and backrests * Refrigerator * LED lighting at the entrance and on the floor * MBUX with DAB+ * Microphone for the driver * Swivel-sliding door * Side windows, black tinted, as a panoramic window with exterior day/night lighting that can be dimmed continuously in the passenger compartment * Telma * USB ports in each row of seats * Deepened trunk including space for the spare tire * Curtains on the side windows * Additional ceiling fan * Additional compartment for skis

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, 5 Wittmann temperature control units are available for sale; the price is for 1 unit. Ksdpfx Asy In Dyoqponc Medium: Water Operating temperature: max. 90°C Heating capacity: 9 kW Cooling capacity: 25 kW

Year of construction: 2006, condition: ready for operation (used), Manufacturer: Wittmann Ksdpfsyk Tfyox Aqpenc Model: TP-PLUS -2:90

Condition: ready for operation (used), Year of construction: 2007, Manufacturer: Wittmann Ksdpfsyk Uiysx Aqpjnc Model: TP-PLUS-2:90

Year of construction: 2008, condition: ready for operation (used), Manufacturer: Wittmann Model: TP-PLUS -2:90 Knedpfxeyk Uvmo Aqpsc

Condition: excellent (used), functionality: fully functional, input voltage: 230 V, year of last overhaul: 2024, total height: 220 mm, total length: 720 mm, total width: 380 mm, type of input current: AC, Temperature control unit Jufeba TG 1-3 T Jufeba model: TG 1-3 T Tabletop unit with container Manual temperature control Robust design 230V connection Used unit, cleaned & tested according to SAB standards Includes warranty + spare parts service Kodsxvk Hdjpfx Aqpjnc We have many more temperature control units in stock!

Condition: excellent (used), functionality: fully functional, input voltage: 230 V, year of last overhaul: 2026, type of input current: AC, input current: 10 A, DGUV certified until: 06/2027, Jufeba TG 1-3 T temperature control unit TOP table-top unit with container Stainless steel design Dry heating system Manual temperature control Robust technology 230V connection Used unit, cleaned With warranty + spare parts service Optional: Maintenance contract Stainless steel GM container Delivery service Training & commissioning Knjdpfxsxiu Hbs Aqpec Visit our large showroom!

Condition: new, Year of construction: 2020, functionality: fully functional, Equipment: documentation/manual, Manufacturer: BRINOX Type: LEP 2.3 – Washing Solution Temperature Control Unit Year of Manufacture: 2020 Serial Number: 1003561 Tag No.: MR-INH-VPR61-KK6751 Equipment No.: 20022779 Location: Germany Condition: New, unused, original packaging Technical Data System Type: Washing Solution Temperature Control Unit (Temperature Control Skid) Knsdpfx Aeyl Ib Ejqpoc Design: Compact, pre-assembled skid unit in stainless steel frame Frame Material: Stainless steel Insulation: Completely insulated piping and components Pumps: Two circulation pumps with electric motors Stainless steel pump housing Inline design Heat Exchanger: Integrated stainless steel heat exchanger Shell and tube or jacketed tube design Valves: Multiple GEMÜ ball valves Stainless steel valves Pneumatic control valves Safety valves Instrumentation: Pressure transmitter Pressure gauges Temperature measuring points Integrated flow measurement Electrical: Integrated control cabinet or terminal box Ready-wired for connection Industrial standard components Piping: Stainless steel process pipelines Fully insulated Flange and clamp connections Transport: Forklift- and crane-compatible Heavy-duty stainless steel base frame Application The temperature control unit is designed for controlled temperature regulation of a washing solution in pharmaceutical or chemical processes. Suitable for CIP and washing processes, pharmaceutical production lines, chemical processing plants, as well as temperature-controlled media circuits. Construction Compact, modular skid design Pre-assembled and ready to connect High-quality stainless steel construction Industrial-grade quality components, including GEMÜ valves Service-friendly design Condition New system Never used Original packaging Direct from manufacturer’s project Immediately available FAT and Documentation Status Technical documentation available Project documentation available Drawings available P&ID available Component lists available Operating manual available Special Features Completely insulated process piping High-quality stainless steel construction Premium industrial components Ideal for new projects or as a replacement/redundant unit Immediate integration possible

Condition: new, Year of construction: 2020, functionality: fully functional, Equipment: documentation/manual, Manufacturer: BRINOX Type: LEP2.3 – Wash Solution Temperature Control Unit Year of Manufacture: 2020 Serial Number: 1003507 LEP2.3 KK6761 Package 8 Tag No.: MR-INH-VPR61-KK6761 Equipment No.: 20023781 Technical Data System Type: Temperature control unit / heating and cooling module for wash solution (CIP or process washing system) Design: Compact, fully pre-assembled skid unit in robust stainless steel frame construction, crane-liftable via integrated lifting points. Frame and Construction: Welded stainless steel construction in industrial design, free-standing, multi-level piping configuration for optimal space utilization. Maintenance-friendly access from multiple sides. Integrated cable trays. Piping: Stainless steel process piping in hygienic design, welded and partially flanged. Multilayer thermal insulation of main lines and apparatus. Integrated drain and vent fittings. Valve Technology: Multiple manual ball valves (GEMÜ) in main and bypass circuits. Pneumatically actuated control and shut-off valves for automatic temperature regulation. Diaphragm and control valves integrated in the heating and cooling circuit. Instrumentation and Control: Temperature measurement points in both supply and return lines. Pressure sensors in the process section. Integrated flow measurement. Electrical junction box with protective labeling. Automatic temperature control via pneumatic control valve. Heat Exchanger: Cylindrical stainless steel heat exchanger, insulated and integrated into the piping system. Designed for controlled heating and/or cooling of the wash solution in a closed loop. Pump Technology: Two electrically driven centrifugal pumps with red-painted motors for process recirculation within the temperature control unit. Electrical: Electrical junction box with warning markings. Wired sensors and actuators. Prepared for integration into a central PLC or process control system. Application This system is used for precise temperature regulation of a wash solution within a pharmaceutical or biotechnological process system. Typical areas of application include CIP systems, production plant washing stations, and temperature-controlled cleaning processes in the pharmaceutical and biotechnology sectors. The wash solution circulates in a closed loop via pumps, is temperature controlled by the integrated heat exchanger, and continuously monitored by sensors. Temperature is regulated automatically via pneumatic control valves to maintain defined setpoints accurately. Knodpfxjyl It Is Aqpec Construction Compact modular skid design with fully insulated main lines. Stainless steel surfaces in hygienic industrial finish. Clearly organized media routing and structured piping layout. Crane-transportable via integrated lifting points. Condition Year of manufacture 2020. Very good visual and technical condition. Professional execution in pharmaceutical plant engineering. FAT / Documentation Typically supplied with CE conformity, Factory Acceptance Test (FAT), and technical documentation including P&ID diagrams and material certificates for product-contacting components. Special Features Fully insulated temperature control module in a compact, high power density design. High-quality valve technology (GEMÜ). Multiple integrated measurement and control points. Suitable for validated pharmaceutical processes. Industrial, pre-assembled skid solution with clearly structured media routing.

Condition: used, Year of construction: 2010, 2010 Mahler HWE 4400/2000/4400 Tempering Bogie Hearth Furnace With Pro Therm (Siemens PLC) Control & Switchgear Usable Chamber Approx Dimensions L4,400 x W4,400 x H2,000mm. Holding Time At 600°C 3–4h. Temperature Uniformity (After 4h Hold) +/- 5K. Batch Weight 15t. Furnace Atmosphere Air. Material Of Parts Steel. Heating Electric. 8 Heating Control Zones. 7 Air Circulation Fans. Installed Heating Capacity Approx 1,680kW Bogie (Car) Approx Travel Speed 50mm/s. Bogie (Car) Approx Load Capacity 15t. Number Of Doors 2. Surface Losses Approx. 30kW. Exhaust Air Volume Flow Approx. 1,000–1,200 m³/h. Exhaust Air Temperature Approx. 250 °C. Max. Ambient Temperature 40 °C. Mains Voltage 3 x 400 V Control Voltage 230 V AC / 24 V DC. S/No. 241 09 (2010). Kjdpfx Aqsz Nh Dreponc

Condition: used, Year of construction: 2011, machine/vehicle number: 253321-01-04, Temperature control unit by gwk, used and untested. Designed for tool temperature regulation, injection molding, and industrial process engineering. Operates as a single-circuit system with Logotherm control. Uses water* as the medium, with a maximum supply temperature of 30 °C. Heating capacity not specified, pump delivers 35 l/min at 3.5 bar*. Year of manufacture: 2011. Total weight: 200 kg. Knedpsy Su Adsfx Aqpec

Condition: good (used), PTC relays, contactors, semiconductor contactors, relays, isolation amplifiers, temperature transducers -Manufacturer: Phoenix Contact, PT100 temperature monitor -Type: MCR-SL-PT100-SP -Price: per piece -Quantity: 7 pieces -Dimensions: 100/13/H115 mm Kedpfxef Ir D Ae Aqpenc -Weight: 0.1 kg/piece

Condition: new, Year of construction: 2026, Briquetting press NEM 900: production time appr. 5 months for briquetting aluminum chips Throughput: up to maximum 320 kg / h * more details after a free test with heard material . Briquette diameter: Ø 70 mm Optimal briquette length: 70 mm . Technical specifications: Knjdpfsgfm Ryjx Aqpjc Total connection: approx. 31 kW In continuous operation approx. 22 kW 400 volts / 50 Hz / 3 phases Pump: 120 + 60 liters per minute Silo: 1 m³ Silo rollers: 1200 mm Including agitator Oil tank: 600 liters Dimensions: 2500 x 1700 x 1730 mm lxwxh Weight: 2250 kg. Hydraulic pre-compression via slide Main press cylinder Vertical cylinder Above for connecting a cooling unit . One and the source material - max.span: 18 mm - Excessive temperature: temperate room at at least + 5 ° C. - max.weight on agitator: 200kg. - The loading must be free of metals and mineral impurities such as sand, stones, etc. This on the pressing tools and / or responsible wear can result