Hydraulic press

Oy Jaromet AB HR 30 - 10

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. Njdewp Rqfspfx Akcela The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Year of construction: 2026, condition: new, functionality: fully functional, Complete plastics recycling line for films and fibre materials from Taiwan leading Plastics Recycling Machinery manufacturer. GENIUS Machinery Co who have more than 30 years of recycling extruder production and experience. Extruder can be fed without size reduction or shredding.. Materials in baled, loose or reel form can be fed. Line can be supplied complete with Belt conveyor, Cutter compactor, Main extruder, Filtration system, (variety of types to suit requirements), Hot pellet die-face cutting device, Centrifugal pellet dryer, Vibrating screener, Storage silo for pellets. Additional ancillary equipment can be supplied . A two stage " Cascade" version is also available for heavily printed films, or very dirty films requiring double filtration. Alternative sizes from 100 kgs per hr up to 1200 kgs per hr can be offered. Full sales and support and training is available in UK and Europe for these extremely modern and economic machines. Nsdpfowg R Rtox Akcola

Condition: new, Year of construction: 2025, Entry-level sheet fiber laser metal cutting machine Lower laser cutting cost and easy operation The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. Njdpfx Ashwrgtskcola The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Condition: New Laser Type: Fiber Laser Laser Power: 1000W, 1500W, 2000W, 3000W Cutting Area: 3000*1524mm Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Cutting Speed: 0-100m/min Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: used, Year of construction: 2026, operating hours: 15 h, functionality: fully functional, machine/vehicle number: 204065, Used machine CNC cutter/plotter Cutting area in X and Y: 3,500 x 2,100 mm. Multifunctional CAM cutting system in CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam and other flat, semi-flexible or rigid, non-metallic materials Equipment of the used machine • 1 cutting bridge and 1 multifunctional tool head The machine is sold with one driven circular knife, electric oscillating knife and one Milling Head + exhaust • Multifunctional tool head to hold max. 2 interchangeable tools • powerful vacuum blower for fixing the material • Standard equipped with gray conveyor table (Conveyor). Green-blue exchange conveyor possible (offers high contrast for dark materials) Can be extended with other tools (on request): • EOT electric oscillating blade • POT pneumatic oscillating knife • PRT rotating blade • UCT universal blade • KCT Kiss-Cut tool • CTT creasing tool • V-Cut angle-cut cutting blade • Punching tool for pinches or holes • Printer mark detection • Camera registration Easy-to-use function • Easy interchangeable cutting tools, "PLUG & CUT • Intuitive user interface • Easy blade change • Vacuum zones can be activated with a click Fast amortization • Low cost with high added value • Best material utilization through nest expert software modules (not included in equipment) • High velocity • Constant precision Data: • Short cutting times due to high positioning speed up to 90 m/min. • Repeatabiliy +/- 0.25 mm • Cuts single or multiple layers Nsdpfx Asif Ek Rjkcela • Suitable for both single ply and multi ply or sheet goods and roll goods (can be extended with suitable unwinder) (Product photo as example) The machine is CE certified.

Condition: used, Year of construction: 2008, turning diameter 1000 mm swing diameter 1250 mm turning height 500 mm control Siemens Sinumerik 840 D Workpiece spindle flange diameter 520 mm work piece spindle speed range 0-440 U/min total power requirement 75 kW weight of the machine ca. 25 t dimensions of the machine ca. 5100 x 3034 x 4500 mm With grinding spindle Table travel: - Z1/Z2 axis 1000 mm, - X1/X2 axis approx. 1300 mm Table speed continuously adjustable: - Z axis 0–30 m/min, - X axis 0–50 m/min - Feed speed continuously adjustable 0.01–15 mm/min - Feed dependent on stroke 0.0005–0.1 mm - Workpiece spindle positioning C axis Nedpfxew Rgcfe Akcela Equipment/accessories: - Grinding spindle - Kaiser dresser - Tool measuring probe - Filter system - With flushing nozzle connections - 2 Capto holders - 1 set of jaws for chuck - technical documentation

Year of construction: 2006, condition: like new (used), Container volume 32 m3 Njdpfx Ajfhb Tkskcjla

Condition: good (used), Year of construction: 2015, travel distance X-axis: 650 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 650 mm, 1 Horizontal machining center Make: STARRAG HECKERT, type: HEC 400D, year 2015, Nlsdpfx Ajuav H Nskcoa Control system, Siemens, type Sinumerik 840D, travel X/Y/Z = 650 x 650 x 650 mm, 2-fold pallet changer, pallet size 400 x 400 mm, NC rotary table 360x 0.001°, 80-fold tool changer, HSK 63 tool holder, spindle speed 15,000 rpm, IKZ 50 bar, belt filter, coolant temperature control, spindle cooling, chip conveyor, sound and control cabinets, operating hours 43,698, spindle hours 5,401

Condition: excellent (used), Year of construction: 2015, Maximum turning diameter: approx. 380 mm Maximum swing over bed: approx. 675 mm Maximum turning length: approx. 500–540 mm Bar capacity (main spindle): approx. 76 mm (3″) MAIN SPINDLE Maximum spindle speed: 4,000 rpm Spindle motor power: 26 kW Spindle bore: approx. 77–88 mm Chuck: 8″ power chuck SUB SPINDLE Maximum spindle speed: 6,000 rpm Spindle motor power: approx. 11 kW Chuck: 6″ or 8″ power chuck Part transfer function AXES X-axis travel: approx. 230 mm Z-axis travel: approx. 575 mm C-axis on main spindle (full contouring and interpolation) TURRET / TOOLING Number of tool stations: 12 positions Live tooling capability (drilling and milling) Tool measurement system (Tool Eye) CNC control: Mazatrol Matrix Nexus Nljdpfeyg It Dex Akcsa EIA/ISO programming Conversational Mazatrol programming 19″ color LCD screen (touch screen) COOLING & CHIP HANDLING High pressure coolant through spindle: 15 bar External flood coolant via spindle nozzles Hinged belt chip conveyor with side discharge Complete coolant system with pumps and filters AUTOMATION Automatic bar feeder included Automatic chuck open/close Chuck status feedback via sensors Automatic part transfer between spindles OTHER FEATURES Pitch error compensation (X, Z) 3D tool compensation Helical interpolation Polar coordinate programming Thread cutting (G33) Workpiece coordinate rotation User macro functions Tool breakage detection MACHINE DIMENSIONS & WEIGHT (approx.) Machine weight: 5,000 – 5,500 kg Machine footprint: approx. 2,600 × 2,000 × 1,900 mm

Condition: excellent (used), Year of construction: 2014, DOOSAN PUMA 2600LMB (2014) CNC LATHE WITH LIVE TOOLS AND “C” AXIS Z-1,350 CNC FANUC i Series 10.4” Color LCD EZ-Guide - Swing over bed: 780 mm - Swing over carriage: 630 mm - Max. turning diameter: 376 mm - Max. turning length: 1,245 mm - Travel: X 260 mm Z 1,350 mm - Chuck diameter: 380 mm - Bar capacity: 102 mm - Spindle nose: ASA-A2-11 - Headstock: 2,800 rpm, 22 kW - Driven turret: 12 stations BMT 65P* (Indexing 1 station 0.25 sec) - Live tools: 5.5 kW, 5,000 rpm - C axis indexing: 0.001 mm - Tailstock quill diameter/travel: 100 mm/100 mm EQUIPMENT INCLUDED: Njdjyb Sryopfx Akcela - Samchully HCH-15” 3-jaw hydraulic chuck, 380 mm diameter - C-axis 360° (0.001°) - Automatic tool presetter - Integrated tailstock - High-pressure pump - Chip conveyor - Preparation, base, and logic for steady rest - SMW AUTOBLOK SLU-3.1 hydraulic steady rest (20-165 mm) - Set of tool holders - Set of DOOSAN and FANUC manuals CONDITION: Machine in good condition. Can be seen in operation. Immediate delivery.

Year of construction: 2023, condition: new, ! Offers for customers from Baltic states only: Lithuania, Latvia, Estonia. Guillotine RAPIDO is fast reliable shearing machine. Depends on sheets length there are guillotines with different working lengths available: 1300 mm / 2600 mm / 3200 mm / 4100 mm. Machine can do up to 35 cuts per minute. The drive system with eccentrics, pulldown rods, and hold down system which can be positioned as close as 2.5 cm from the knives allow for easy and expedient trimming of narrow strips. RAPIDO guillotine shear is equipped with squaring arms on both sides and the LED cutting line light. Nodpfoixz D Ujx Akcola Available working lengths: 2600 mm / 3200 mm / 4100 mm