Double-Column Presse

SMG DS 25

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 480 mm 610 x 450 saw band length 5320 x 34 x 1,1 mm band speed 15 - 100 m/min table height 820 mm total power requirement 3,0 kW weight of the machine ca. 2,3 t dimensions of the machine ca. 2,65 x 2,8 x 2,2 m Hfsdpfxefu Nbbs Ad Dsp For miter cuts up to 45° left in fully automatic Operation and up to 60° left in semi-automatic operation Material height sensor (automatic cut start detection) Automatic feed unit via ball screw with incremental feed automatic length compensation Button on the saw band for automatic adjustment of the saw stroke Fully automatic control of the saw frame and clamping device Hydraulic unit with automatic pressure shut-off when idling Mechanical chip clearing brush feed vice opening on both sides Remaining piece length 100 mm Modern CNC control freely programmable for multiple sawing jobs with various Cutting lengths and quantities. Automatic feed unit 500 mm via ball screw incremental feed with automatic length compensation. Adjustable for section lengths of 25 – 9,999mm. Fully hydraulic control of saw frames and clamping devices Preselection of 3 different material feed speeds Visualization of the entire workflow with simple data entry

Condition: new, Year of construction: 2025, Semi-automatic sawing process with automatic clamping, sawing, and raising of the workpiece to preset height after the cut is finished Stepless hydraulic cutting pressure and feed monitoring at the saw band press. Therefore, optimal conditions for every sawing task, i.e., constant pressure for solid material and constant feed for thin-walled profiles. Particularly suitable for universal application with different cross-sections, materials, and frequently changing miter cuts The machine control complies with CE standard 89/289 Technical data: round/flat 90° 325/500 x 300 45° 300/300 x 300 30° 200/200 x 200 Rapid feed lowering of the saw frame to the material edge by push button Manual miter adjustment from 90° - 30°, infinitely variable on a scale The miter pivot point is the intersection between the saw band and the fixed clamping jaw, resulting in no length change when adjusting the angle Hydraulic full-stroke workpiece clamping - CETOP hydraulic system At every saw frame angle, the material is clamped parallel at 90° Complete coolant device with electric immersion pump Central machine operation Saw band drive with end stop Movable band guide arm, adjustable to material width Saw band deflection roller with carbide guide Chip cleaning brush, rotating Saw band tensioning with torque wrench Painting silver-grey/blue-grey (RAL 7001/RAL 7031) Remnant length: 25mm Cutting speed: AC frequency-controlled drive 15-150 m/min continuously adjustable at the control panel Drive Saw band 3.0 kW; 400V, 50Hz Hodpfxjhppabj Ad Dofp Hydraulics 1.1 kW Coolant pump 0.1 kW Saw frame feed: Continuously up to 300mm/min, hydraulically controlled Saw band tension: Mechanically with torque wrench Saw band dimensions: 4200x34x1.1mm Working height: 750mm (without base elements) Weight: 850kg Dimensions (LxWxH): 1300x2050x1400mm The following options are available: Laser light Micro-spraying device Clamping pressure regulator Support table on the feed side

Condition: used, Year of construction: 2020, clamping force: 90 kN, displacement volume: 113 cm³, injection pressure: 2,400 bar, overall weight: 7,500 kg, load hours: 4,200 h, screw conveyor diameter: 30 mm, terms of delivery: EXW (ex Works) delivery time: on request Hfjdpfxov S H N Rj Ad Dep terms of payment: 100% prior to delivery

Condition: new, 550 mm 550 mm 550 x 550 mm saw band length 5980 x 41 x 1,3 mm table height 800 mm band speed 20 - 100 m/min total power requirement 5,5 kW weight of the machine ca. 3,8 t dimensions 3,0 x 2,15 x 2,2 m PROMOTIONAL PRICE!!!! 2-column high-performance automatic band saws from the SBS series The SBS series impresses with its sophisticated technology, high quality and longevity and unrivaled, sophisticated standard equipment. • Modern SNC 20 control for CNC version Hfsdefg E Hwjpfx Ad Dop • Frequency-controlled saw drive • Control buttons with pictograms • Work light • Powered chip brush • Hydraulic belt tension • Clamping pressure regulation • Double vice (before and after the belt) • Creep path for positioning • Bundle tension prepared electrically and hydraulically • Chip conveyor The SNC 20 control allows you to enter up to 20 different sawing tasks (length and number of pieces) conveniently and easily. When the target dimension is entered, the control automatically calculates the saw waste and the number of feeds. Additionally, the error code display system provides quick analysis for troubleshooting.

Condition: used, _____ Description: Year of manuf. : 2009 Control : Siemens C200-4D SL In General: Year of construction:2009 Hfjdsvxmy Nspfx Ad Dep Control system:Siemens 840 Dsl (C200-4D SL) Bar capacity:65 mm Milling spindles:18,000 rpm Main spindle: Technology:Motorised spindle Speed:5,000 rpm Max. power:35.5 kW Torque max.:170 Nm C-axis:0.001° Z-axis:390 mm Bar capacity:65 mm Clamping cylinder:Hollow clamping cylinder Chuck:3-jaw chuck Sub spindle: Technology:Motorised spindle Speed:5,000 rpm Max. power:35.5 kW Torque max.:170 Nm C-axis:0.001° X-axis:600 mm Z-axis:390 mm Bar capacity:65 mm Chuck:3-jaw chuck Tool carrier I: Technology:Milling spindle on cross slide Speed:18,000 rpm Tool holder:HSK 40 X-axis:350 mm Y-axis:160 mm (+/- 80 mm) B-axis:230° Tool carrier II: Technology:Milling spindle on cross slide Speed:18,000 rpm Tool holder:HSK 40 Y-axis:160 mm(+/- 80 mm) B-axis:230° Tool magazin: Technology:Chain magazine Number of stations:80 pieces Tool changer:Double gripper Tool length max.:180 mm Equipment: Chip disposal:Chip conveyor Coolant supply:IKZ system with filter Parts removal:Gantry-type pick-up Bar loader interface:Electrically prepared Tool monitoring:Drill breakage monitoring

Year of construction: 1997, condition: ready for operation (used), Turning diameter: 200mm, turning length: 400mm, turning diameter: 420mm, bar diameter: 60mm, max. spindle chuck diameter: 160mm, speed: 5000rpm, turret: 2, positions: 2x14, rapid traverse X/Z: 20m/min/30m/min. Machine dimensions X/Y/Z: approx. 7500mm/2100mm/2100mm, weight: approx. 4500kg. Documentation available. On-site inspection is possible. Hfsdpfxsu T Rgke Ad Dsp

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. Hfedpfjfg E Hpsx Ad Dep • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 1250x600 mm capacity 45 degrees: round 680 mm capacity 45 degrees: square 600 mm capacity 45 degrees: flat 870x600 mm capacity 60 degrees: round 580/550 mm capacity 60 degrees: square 530/450 mm capacity 60 degrees: flat 550x450 mm saw band length 8140 x 54 x 1,6 mm band speed 15 - 90 m/min table height 855 mm total power requirement 7,5 kW weight of the machine ca. 5,3 t dimensions of the machine ca. 5,75 x 4,2 x 2,75 m 2-column double miter band saw for quick cutting with pusher system P15. Option P30 Hydraulic saw frame lowering • NC controlled • Automatic angular positioning from + 60° to – 60° High quality automatic miter adjustment Special development for cutting profiles and beams. The highest positioning accuracy is achieved via the new “B&S positioning system”. reached. An intelligent NC control ensures smooth interaction of linear encoder and self-braking positioning motor in conjunction with a reliable hydraulic brake using large radial center positioning. The work table is supported by high-quality preloaded bearings, which ensure very smooth rotation. CNC Control A CNC control allows the programming of up to 90 cutting programs with different section lengths, quantities and mitres. Positioning system gripping on both sides The B&S pusher system, feeding and positioning system, is marked “on both sides Hsdpfx Adofg E Hno Dofp “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: good (used), functionality: fully functional, Year of construction: 2014, laser power: 3,000 W, X Working area max.: 2500 mm Y Working area max.: 1250 mm Control: IndraMotion MTX Laser power: 3000 watts Standard equipment: Machine - Coordinate guide for high-precision machining - Stable, easily accessible C-frame - Linear magazine with 21 tool positions and 4 clamps - Drives with maintenance-free three-phase servo motors - Repositioning device with programmable hold-down device - Foot switch for clamp closing - Ball tables - 2 part flaps 500 mm x 500 mm - FocusLine - NitroLine - FastLine - Ejection cylinder for laser parts - Slag cone detection TRUMPF laser - TruDisk 3001 solid-state laser with 1 LLK outlet - Excitation via pump diodes - LLK according to standard layout (10m) - TruControl laser control 1000 - Cooling unit - Laser logbook function Cutting head - Solid-state laser compact cutting unit - ControlLine Punching head - Electro-hydraulic punching head - Rotatable mono tool holder - Tool length compensation - Programmable hold-down device (active / passive / repositioning) - Punch stroke counter and thread stroke counter - Spray lubrication of punch - Punch slug extraction - Calculation of filling level in the punching console - Level monitoring of thread forming and tool lubrication Control - Open control based on Rexroth IndraMotion MTX - Control panel with 17" touch control panel - Program management - Production plan - Integrated technology data - Teleservice via Internet - Programmable cutting gas pressure - Automatic switch-off with wake-up mode Data transfer - USB interface - RJ-45 network connection Safety - CE marking - Two-beam light barriers - Monitoring system for, among others Gas pressure, temperature, cooling water - Quick shutdown hydraulics - Protection against scattered radiation - Compact dust extraction system - MultiTool function - MultiBend function - Thread forming function Hfjdpfx Aswld Sued Dop - Engraving function - Deburring and rolling technology function - SoftPunch function - StripLine - Lowerable die - Spray lubrication die including level monitoring - Additional clamping claw - 4 pcs. Height-adjustable clamping claws - Vibration-damped installation - Chip conveyor with tilting container - Blow-out device for small parts - Warping detection SheetMaster - Unloading platform - Suction frame with 36 suction cups - Peeling suction cup - Vacuum sensors for each suction cup - Double sheet detector for double sheet control - Central lubrication - TRUMPF control based on Rexroth IndraMotion MTX - Automatic clamp closing machine - Loading and unloading parallel to production time - Peeling system including positioning aid medium format (2500x1250) - First additional suction cup package standard - Second additional suction cup package standard - Unloading monitoring laser parts GripMaster - Parts conveyor belt punching station - Parts conveyor belt laser station ToolMaster with 70 stations (only for punching operation) - ToolMaster set-up parallel to production time

Year of construction: 2017, condition: ready for operation (used), Laser power: 10kW (10000W), working range: 3000mm/1500mm, max. material thickness: mild steel: 25mm, stainless steel: 30mm, aluminum: 30mm, copper: 12mm, brass: 15mm. Positioning speed: 120m/min, positioning accuracy: +/-0.05mm, max. workpiece weight: 1100kg. Machine dimensions X/Y/Z: approx. 9500mm/3500mm/3500mm, suction dimensions X/Y/Z: approx. 1500mm/1500mm/4000mm, machine weight: approx. 12000kg, operating hours: approx. 17000h. Documentation available. On-site inspection is possible. Expected to be available from June 2025. Hfedpfjvyiqgox Ad Dop